S LW 0 5 5W DC-DC Regulated Single Output Converter series Features : 2:1 wide input range 4:1 wide input range(option) 1000VDC I/O isolation 3000VDC I/O isolation(option) Built-in EMI filter Protections: Short circuit / Overload Cooling by free air convection Six-sided shield metal case 100% burn-in test Low cost / High reliability Approvals: FCC / CE 2 years warranty SPECIFICATION ORDER NO. SLW05A- SLW05B- SLW05C- SLW05A- SLW05B- SLW05C- SLW05A- SLW05B- SLW05C- SLW05A- SLW05B- SLW05C05 05 05 09 09 12 12 12 15 15 15 09 DC VOLTAGE 5V 9V 12V 15V CURRENT RANGE 100 ~ 1000mA 55.6 ~ 556mA 41.7 ~ 417mA 33.3 ~ 333mA RATED POWER 5W 60mVp-p 60mVp-p 60mVp-p VOLTAGE ACCURACY OUTPUT 2.0% RIPPLE & NOISE (max.) Note.2 50mVp-p LINE REGULATION Note.3 0.2% LOAD REGULATION A: 9 ~ 18VDC EFFICIENCY (Typ.) 75% 77% Full load A: 556mA B: 270mA No load A: 33mA FILTER C: 36 ~ 72VDC 80% B: 16mA 80% 83% 80% 80% 83% 81% 81% 85% C: 135mA C: 10mA 160 ~ 250% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed SHORT CIRCUIT All output equipped with short circuit Protection type : Hiccup mode, recovers automatically after fault condition is removed WORKING TEMP. -25 ~ +71 WORKING HUMIDITY 20% ~ 90% RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION WITHSTAND VOLTAGE SAFETY & ISOLATION RESISTANCE OTHERS 77% OVER CURRENT PROTECTION EMC B: 18 ~ 36VDC Pi network Fuse recommended PROTECTION (Note. 5) 50KHz min. VOLTAGE RANGE DC CURRENT INPUT 0.5% Note.4 SWITCHING FREQUENCY (Refer to output load derating curve) -25 ~ +105 , 10 ~ 95% RH 0.03% / (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes I/P-O/P:1KVDC I/P-O/P: 100M Ohms / 500VDC / 25 / 70% RH EMI CONDUCTION & RADIATION Compliance to EN55022 Class B, FCC part 15 Class B Compliance to EN61000-4-2,3,4,5,6,8, light industry level, criteria A EMS IMMUNITY 800khrs min. MIL-HDBK-217F(25 ) MTBF DIMENSION 50.8*25.4*11.27mm or 2"*1"*0.44" inch (L*W*H) 32g WEIGHT Derating Curve Pin Configuration Mechanical Specification Unit:mm 50.8 3 10.2 10.2 1 4 2 BOTTOM VIEW 5 0.8 + 0.1/-0 5.8(0.13) Pin no. Output Single 1 2 3 4 5 + Vi n - Vi n + Vo u t No Pin - Vo u t 100 LOAD (%) 11.27 15.2 2.5 20.3 2.5 25.4 10.2 5.1 10.1 15.3 80 -25 0 25 50 60 71 Ta ( NOTE 100 ) 1.All parameters are specified at normal input, rated load, 25 70% RH ambient. 2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor. 3.Line regulation is measured from low line to high line at rated load. 4.Load regulation is measured from 10% to 100% rated load. 5.Please prevent the converter from operating in overload or short circuit condition for more than 30 seconds. File Name:SLW05-SPEC 2008-05-12