1N6102US thru 1N6137AUS and 1N6138US thru 1N6173AUS Voidless-Hermetically-Sealed Surface Mount Bidirectional Transient Suppressors SCOTTSDALE DIVISION APPEARANCE This surface mount series of industry recognized voidless-hermeticallysealed Bidirectional Transient Voltage Suppressor (TVS) designs is military qualified to MIL-PRF-19500/516 and are ideal for high-reliability applications where a failure cannot be tolerated. They provide a Working Peak “Standoff” Voltage selection from 5.2 to 152 Volts with two package sizes for 500 W and 1500 W ratings. They are very robust in hard-glass construction and also use an internal metallurgical bond identified as Category I for high-reliability applications. Both of these are also military qualified to MIL-PRF-19500/516 and are available as both a non suffix part and an “A” suffix part involving different voltage tolerances as further described in note 4 on page 2. These devices are also available in axialleaded packages for thru-hole mounting by deleting the “US” suffix (see separate data sheet for 1N6102 thru 1N6173A). Microsemi also offers numerous other TVS products to meet higher and lower peak pulse power and voltage ratings in both through-hole and surface-mount packages. Package “E” (or “D-5B”) Package “G” (or “D-5C”) WWW . Microsemi .C OM DESCRIPTION IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com FEATURES • • • • • • • APPLICATIONS / BENEFITS High surge current and peak pulse power provides transient voltage protection for sensitive circuits Triple-layer passivation Internal “Category I” metallurgical bonds Voidless hermetically sealed glass package JAN/TX/TXV military qualifications available per MIL-PRF19500/516 by adding JAN, JANTX, or JANTXV prefix (consult factory for 1N6102US and 1N6138US) JANS available for 1N6103AUS thru 1N6118AUS per MIL-PRF-19500/516 as well as further options for screening in accordance with MIL-PRF-19500 for JANS on all others in this series by using a “MSP” prefix, e.g. MSP6119AUS, MSP6143AUS, etc. Axial-leaded equivalents also available (see separate data sheet for 1N6102 thru 1N6173) MAXIMUM RATINGS • • • • • • • • • Military and other high reliability transient protection Extremely robust construction Extensive range in Working Peak “Standoff” Voltage (VWM) from 5.2 to 152 V Available as either 500 W or 1500 W Peak Pulse Power (PPP) using two different size packages ESD and EFT protection per IEC6100-4-2 and IEC61000-4-4 respectively Secondary lightning protection per select levels in IEC61000-4-5 Square-end-cap terminals for easy placement Nonsensitive to ESD per MIL-STD-750 Method 1020 Inherently radiation hard as described in Microsemi MicroNote 050 MECHANICAL AND PACKAGING o o Copyright 2004 1-05-2005 REV B Microsemi Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503 Page 1 1N6102US – 1N6137AUS 1N6138US – 1N6173AUS • CASE: Hermetically sealed voidless hard glass with • Operating (TJ) & Storage Temperature: -55 C to +175 C o Tungsten slugs • Peak Pulse Power (PPP) at 25 C: 500 W for 1N6102US to • TERMINATIONS: End caps are solid Silver (Ag) 1N6137AUS and 1500 W for 1N6138US to 1N6173AUS @ with Tin/Lead (Sn/Pb) finish 10/1000 µs (also see Figures 1,2 and 3) • MARKING: None • Impulse repetition rate (duty factor): 0.01% • POLARITY: No polarity marking for these • Steady-State Power: 3.0 W for 1N6102US to 1N6137AUS bidirectional TVSs and 5.0 W for 1N6138US to 1N6173AUS up to TEC = 150oC. Linearly derate above TEC =150oC to zero at TEC =175oC. • Tape & Reel option: Standard per EIA-481-B • Steady-State Power: 2.0 W for 1N6102US to 1N6137AUS • Weight: 539 mg for 500 Watt (E Package) and 3.0 W for 1N6138US to 1N6173AUS @ TA = 25oC (see 1100 mg for 1500 Watt (G Package) note and Figure 4 for linear derating at higher temperatures) • See package dimensions and recommended pad • Thermal Resistance (junction to endcap): 8.3 oC/W for layouts on last page for both the “E” (D-5B) and “G” o 1N6102US to 1N6137AUS and 5.0 C/W for 1N6138US to (D-5C) size packages 1N6173AUS • Solder Temperatures: 260oC for 10 s (maximum) NOTE: Steady-state power ratings with reference to ambient are for PC boards where thermal resistance from mounting point to ambient is sufficiently controlled where TOP or TJ(MAX) is not exceeded 1N6102US thru 1N6137AUS and 1N6138US thru 1N6173AUS Voidless-Hermetically-Sealed Surface Mount Bidirectional Transient Suppressors SCOTTSDALE DIVISION INDUSTRY TYPE NUMBER (Note 4) PPP Rating 500W 1500W 1N6102AUS 1N6138AUS 1N6103AUS 1N6139AUS 1N6104AUS 1N6140AUS 1N6105AUS 1N6141AUS 1N6106AUS 1N6142AUS 1N6107AUS 1N6143AUS 1N6108AUS 1N6144AUS 1N6109AUS 1N6145AUS 1N6110AUS 1N6146AUS 1N6111AUS 1N6147AUS 1N6112AUS 1N6148AUS 1N6113AUS 1N6149AUS 1N6114AUS 1N6150AUS 1N6115AUS 1N6151AUS 1N6116AUS 1N6152AUS 1N6117AUS 1N6153AUS 1N6118AUS 1N6154AUS 1N6119AUS 1N6155AUS 1N6120AUS 1N6156AUS 1N6121AUS 1N6157AUS 1N6122AUS 1N6158AUS 1N6123AUS 1N6159AUS 1N6124AUS 1N6160AUS 1N6125AUS 1N6161AUS 1N6126AUS 1N6162AUS 1N6127AUS 1N6163AUS 1N6128AUS 1N6164AUS 1N6129AUS 1N6165AUS 1N6130AUS 1N6166AUS 1N6131AUS 1N6167AUS 1N6132AUS 1N6168AUS 1N6133AUS 1N6169AUS 1N6134AUS 1N6170AUS 1N6135AUS 1N6171AUS 1N6136AUS 1N6172AUS 1N6137AUS 1N6173AUS Volts 6.12 7.13 7.79 8.65 9.50 10.45 11.40 12.35 14.25 15.20 17.10 19.0 20.9 22.8 25.7 28.5 31.4 34.2 37.1 40.9 44.7 48.5 53.2 58.9 64.6 71.3 77.9 86.5 95.0 104.5 114.0 123.5 142.5 152.0 171.0 190.0 mA 175 175 150 150 125 125 100 100 75 75 65 65 50 50 50 40 40 30 30 30 25 25 20 20 20 20 15 15 12 12 10 10 8 8 5 5 RATED STANDOFF VOLTAGE VWM Volts 5.2 5.7 6.2 6.9 7.6 8.4 9.1 9.9 11.4 12.2 13.7 15.2 16.7 18.2 20.6 22.8 25.1 27.4 29.7 32.7 35.8 38.8 42.6 47.1 51.7 56.0 62.2 69.2 76.0 86.6 91.2 98.8 114.0 121.6 136.8 152.0 MAXIMUM STANDBY CURRENT ID@ VWM 500W 1500W uA uA 100 500 50 300 20 100 20 100 20 100 20 20 20 20 20 20 20 20 20 20 1 10 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 1 5 MAXIMUM CLAMPING VOLTAGE VC @ IPP Volts 10.5 11.2 12.1 13.4 14.5 15.6 16.9 18.2 21.0 22.3 25.1 27.7 30.5 33.3 37.4 41.6 45.7 49.9 53.6 59.1 64.6 70.1 77.0 85.3 97.1 103.1 112.8 125.1 137.6 151.3 165.1 178.8 206.3 218.4 245.7 273.0 MAXIMUM PEAK PULSE CURRENT IPP 500 W Amps 47.6 44.6 41.3 37.3 34.5 32.0 29.6 27.5 23.8 22.4 19.9 18.0 16.4 15.0 13.4 12.0 10.9 10.0 9.3 8.5 7.7 7.1 6.5 5.9 5.1 4.8 4.4 4.0 3.6 3.3 3.0 2.8 2.4 2.3 2.0 1.8 1500 W Amps 142.8 133.9 124.0 111.9 103.4 96.2 88.8 82.4 71.4 67.3 59.8 54.2 49.2 45.0 40.1 36.0 32.8 30.1 28.0 25.4 23.2 21.4 19.5 17.6 15.4 14.5 13.3 12.0 10.9 9.9 9.1 8.4 7.3 6.9 6.1 5.5 Note: 4 1 1 1 2 3 1 2 3 Applies to both 500W and 1500W series for devices shown (see note 4) Applies only to 500W series (1N6102US thru 1N6137US) Applies only to 1500W series (1N6138US thru 1N6173AUS) Part number without the A suffix has 5% higher VC, 5% lower minimum V(BR), and 5% lower IPP. Symbol VBR VWM ID VC PPP Copyright 2004 1-05-2005 REV B MAXIMUM TEMP. COEF. OF V(BR) o %/ C .05 .06 .06 .06 .07 .07 .07 .08 .08 .08 .085 .085 .085 .09 .09 .09 .095 .095 .095 .095 .095 .095 .095 .100 .100 .100 .100 .100 .100 .100 .100 .105 .105 .105 .110 .110 1 SYMBOLS & DEFINITIONS Definition Minimum Breakdown Voltage: The minimum voltage the device will exhibit at a specified current. Working Peak Voltage: The maximum peak voltage that can be applied over the operating temperature range. This is also referred to as Standoff Voltage. Maximum Standoff Current: The maximum current that will flow at the specified voltage and temperature. Maximum clamping voltage at specified IPP (Peak Pulse Current) at the specified pulse conditions. Peak Pulse Power: The peak power dissipation resulting from the peak impulse current IPP. Microsemi Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503 Page 2 1N6102US – 1N6137AUS 1N6138US – 1N6173AUS Notes: 1. 2. 3. 4. MINIMUM BREAKDOWN VOLTAGE V(BR) @ I(BR) WWW . Microsemi .C OM ELECTRICAL CHARACTERISTICS 1N6102US thru 1N6137AUS and 1N6138US thru 1N6173AUS SCOTTSDALE DIVISION Voidless-Hermetically-Sealed Surface Mount Bidirectional Transient Suppressors MAX PEAK PULSE POWER (PPP) OR CURRENT (IPP) IN PERCENT OF MAX RATINGS 10,000 1000 100 Peak Pulse Power (PPP) WWW . Microsemi .C OM GRAPHS PULSE TIME (tp) FIGURE 1 PEAK PULSE POWER vs. PULSE TIME o JUNCTION TEMPERATURE (TJ) IN C PULSE CURRENT (IPP) IN PERCENT OF IPP FIGURE 2 PULSE DERATING CURVE (prior to impulse) 1N6102US – 1N6137AUS 1N6138US – 1N6173AUS TIME (t) IN MILLISECONDS FIGURE 3 PULSE WAVE FORM Copyright 2004 1-05-2005 REV B Microsemi Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503 Page 3 1N6102US thru 1N6137AUS and 1N6138US thru 1N6173AUS Voidless-Hermetically-Sealed Surface Mount Bidirectional Transient Suppressors WWW . Microsemi .C OM MAXIMUM STEADY-STATE POWER IN WATTS SCOTTSDALE DIVISION FIGURE 4 STEADY-STATE DERATING CURVE FOR FREE-AIR MOUNTING ON PC BOARD PACKAGE DIMENSIONS and PAD LAYOUTS 1N6102US – 1N6137AUS 1N6138US – 1N6173AUS E-MELF-PKG (D-5B) for 1N6102US thru 1N6137AUS (500 W) Note: If mounting requires adhesive separate from the solder, an additional 0.080 inch diameter contact may be placed in the center between the pads as an optional spot for cement as shown in the pad layout. Copyright 2004 1-05-2005 REV B Microsemi Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503 Page 4 1N6102US thru 1N6137AUS and 1N6138US thru 1N6173AUS SCOTTSDALE DIVISION Voidless-Hermetically-Sealed Surface Mount Bidirectional Transient Suppressors WWW . Microsemi .C OM PACKAGE DIMENSIONS and PAD LAYOUTS G-MELF-PKG (D-5C) for 1N6138US thru 1N6173AUS (1500 W) Note: If mounting requires adhesive separate from the solder, an additional 0.090 inch diameter contact may be placed in the center between the pads as an optional spot for cement as shown in the pad layout. 1N6102US – 1N6137AUS 1N6138US – 1N6173AUS Copyright 2004 1-05-2005 REV B Microsemi Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503 Page 5