MORNSUN MSA4815MD-3W

MSA_(M)D-3W & MSB_(M)D-3W Series
3W, WIDE INPUT, ISOLATED & REGULATED
DUAL/SINGLE OUTPUT DIP DC-DC CONVERTER
multi-country patent protection
PRODUCT PROGRAM
FEATURES
● Wide (2:1) input range
● Efficiency up to 82%
● Operating temperature: -40°C ~ +85°C
● 1500VDC isolation
● Short circuit protection(Automatic recovery)
● Internal SMD construction
● No heat sink required
● No external component required
● UL94-V0 package
● Industry standard pinout
● MTBF>1,000,000 hours
● RoHS Compliance
Input
Part
Number
Output
Voltage (VDC)
Nominal Range
Voltage
Max* (VDC)
Current (mA)
Efficiency
Certificate
(%, Typ)
Max.
Min.
MSA0505(M)D-3W
±5
±300
±30
68
MSA0512(M)D-3W
±12
±125
±12
72
MSA0515(M)D-3W
±15
±100
±10
73
5
600
60
68
MSB0509(M)D-3W
9
333
33
70
MSB0512(M)D-3W
12
250
25
72
MSB0515(M)D-3W
15
200
20
73
MSA1205(M)D-3W
±5
±300
±30
76
MSA1212(M)D-3W
±12
±125
±12
79
MSA1215(M)D-3W
±15
±100
±10
80
MSB1205(M)D-3W
5
600
60
76
9
333
33
78
MSB1212(M)D-3W
12
250
25
80
The MSA_(M)D-3W &MSB_(M)D-3W Series
MSB1215(M)D-3W
15
200
20
81
are specially designed for applications where a
MSB1224(M)D-3W
24
125
12
82
MSA2405(M)D-3W
±5
±300
±30
76
MSA2412(M)D-3W
±12
±125
±12
80
MSA2415(M)D-3W
±15
±100
±10
81
MSB2403(M)D-3W
3.3
909
90
74
UL
5
600
60
76
UL
MSB2409(M)D-3W
9
333
33
78
UL
MSB2412(M)D-3W
12
250
25
81
UL
MSB2415(M)D-3W
15
200
20
80
UL
MSB2424(M)D-3W
24
125
12
82
MSA4805(M)D-3W
±5
±300
±30
76
MSA4812(M)D-3W
±12
±125
±12
80
MSA4815(M)D-3W
±15
±100
±10
81
MODEL SELECTION
MSB4803(M)D-3W
3.3
909
90
74
MSA2405MD-3W
MSB4805(M)D-3W
5
600
60
76
MSB4809(M)D-3W
9
333
33
78
MSB4812(M)D-3W
12
250
25
81
MSB4815(M)D-3W
15
200
20
80
MSB4824(M)D-3W
24
125
12
82
MSB0505(M)D-3W
MSB1209(M)D-3W
APPLICATIONS
wide range input voltage power supplies are
isolated from the input power supply in a
distributed power supply system on a circuit
board. These products apply to:
1) Where the voltage of the input power supply is
wide range (Voltage range≤ 2:1);
2) Where isolation is necessary between input
and output(Isolation voltage≤1500VDC);
3) Where the regulation of the output voltage and
the output ripple noise are dem anded.
Rated Power
Package Style
Output Voltage
Input Voltage
Product Series
MSB2405(M)D-3W
5
12
24
48
4.5-9
9-18
18-36
36-72
11
22
40
80
* Input voltage over it may cause permanent damage to the device.
Note: Metal package style’s series is MSA_MD-3W & MSB_MD-3W.
MORNSUN Science & Technology co.,Ltd.
Address: 2th floor 6th building, Hangzhou
Industrial District, Guangzhou, China
Tel: 86-20-38601850
Fax: 86-20-38601272
http://www.mornsun-power.com
ISOLATION SPECIFICATIONS
Item
Test conditions
Min.
Isolation voltage
Tested for 1 minute and 1mA max
1500
Isolation resistance
Test at 500VDC
1000
Isolation capacitance
Input/Output
Typ.
Max.
Units
VDC
MΩ
80
The copyright and authority for the interpretation of the products are reserved by Mornsun
Specifications subject to change without notice.
MSA_((M)D-3W&MSB_(M)D-3W
A/2-2009
Page 1 of 3
pF
OUTPUT SPECIFICATIONS
Item
TYPICAL CHARACTERISTICS
Test conditions
Min.
Output power
See below products program
0.3
Positive voltage accuracy
Refer to recommended circuit
Typ.
Max.
Units
3
W
±1
±3
±3
±5
Load regulation
From 10% to 100% load
±0.5
±1*
Line regulation
Input voltage from low to high
±0.2
Temperature drift(Vout)
Refer to recommended circuit
Ripple & Noise**
20MHz Bandwidth
50
Switching frequency
100% load, nominal input voltage
300
Negative voltage accuracy Refer to recommended circuit
%
±0.5
±0.03
%/ °C
100
mVp-p
KHz
100
*Dual output models unbalanced load: ±5%.
**Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing of Power
Converter section, application notes.
COMMON SPECIFICATIONS
RECOMMENDED CIRCUIT
Test Conditions
Min.
Typ.
Storage humidity
Operating temperature
-40
Storage temperature
Lead temperature
Units
95
%
125
15
1.5mm from case for 10 seconds
0.2
Cooling
Cin
°C
300
No-load Power consumption
W
Free air convection
Short circuit protection
Case material
+Vout
Vin
85
-55
Temp. rise at full load
Max.
DC
DC
GND
0V
-Vout
Single Output
Vin
Cin
+Vout
DC
DC
0V
GND
Continuous, Automatic Recovery
D: Plastic (UL94-V0);
MTBF
(Figure 1)
MD: Steel, Nickel Coated
1000
Weight
K hours
15
g
APPLICATION NOTE
Requirement On Output Load
In order to ensure the product operate efficiently and reliably, in addition to a max load
Input Current(A)
Item
Operating Temp.( C )
Ip
Input Voltage
Range
(namely full load), a minimum load is specified for this kind of DC/DC converter. Make sure the
specified range of input voltage is not exceeded, the minimum output load no less than 10%
Input Voltage (V)
load. If the actual load is less than the specified minimum load, the output ripple may increase
sharply while its efficiency and reliability will reduce greatly. If the actual output power is very
small, please add an appropriate resistor as extra loading, or contact our company for other
lower output power products.
Recommended Circuit
All the MSA_(M)D-3W & MSB_(M)D-3W Series have been tested according to the following
recommended testing circuit before leaving factory. This series should be tested under load.
Never be tested under no load (see Figure 1).
If you want to further decrease the input/output ripple, you can increase capacitance properly
Output External Capacitor Table(Table 1)
Single Vout
Cout
Dual Vout
Cout
(VDC)
(uF)
(VDC)
(uF)
5
1000
±5
680
9
680
±9
470
12
470
±12
330
15
330
±15
220
24
220
±24
100
or choose capacitors with low ESR. However, the capacitance of the output filter capacitor must
be proper. If the capacitance is too big, a startup problem might arise. For every channel of
output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter
capacitor sees (Table 1). Generally: If you want to use the products in high EMI, please choose
our metal packaged products (MSA_MD-3W & MSB_MD- 3W). General:
Cin:
5V&12V
100μF
24V&48V
10μF-47μF
Cout: 10μF/100mA
Input Current
When it is used in unregulated power supply, be sure that the fluctuating range of the power
supply and the rippled voltage do not exceed the module standard. Input current of power
supply should afford the startup current of this kind of DC/DC module (See figure 2), General:
Ip ≤1.4*Iin-max
No parallel connection or plug and play
The copyright and authority for the interpretation of the products are reserved by Mornsun
Specifications subject to change without notice.
MSA_((M)D-3W&MSB_(M)D-3W
A/2-2009
Page 2 of 3
OUTLINE DIMENSIONS & PIN CONNECTIONS
MECHANICAL DIMENSIONS
RECOMMENDED FOOTPRINT
∅1.00 [∅0.039]
DUAL OUTPUT
MS_MD
31.80[1.252]
1 2 3
10 11 12
(Bottom View )
24 23 22
15.24 [0.600]
20.30 [0.799]
20.00 [0.787]
15.24 [0.600]
2.54 [0.100]
31.50[1.240]
MS_D
24 23 22
15 14 13
1 2 3
10 11 12
2.54 [0.100]
27.94 [1.100]
15 14 13
2.54 [0.100]
10.00[0.394]
9.50[0.374]
Note:
Unit:mm[inch]
Pin diameter tolerances: ±0.10mm[ ±0.004inch]
General tolerances:± 0.25mm[± 0.010inch]
FOOTPRINT DETAILS
Single
Dual
Pin
Vin
Vin
1,24
2,23
No Pin
-Vo
3,22
No Pin
0V
10,15
0V
0V
11,14
+Vo
+Vo
12,13
GND
GND
NC:No connection
24
15 14 13
1
10 11 12
TUBE OUTLINE DIMENSIONS
22.70 [0.894]
18.20 [0.717]
0.50 [0.020]
MS_MD
(Side View)
MS_D
4.10 [0.161]
27.94 [1.100]
11.60[0.457]
MS_D
MS_MD
SINGLE OUTPUT
0.60 [0.024]
11.30 [0.445]
Note:
Unit :mm[inch]
General tolerances: ±0.50mm[±0.020inch]
L=530mm[20.866inch] Tube Quantity: 15pcs
L=220mm[8.661inch] Tube Quantity: 6pcs
Note:
1. The load shouldn't be less than 10%, otherwise ripple will increase dramatically.
2. Operation under 10% load will not dam age the converter; However, they may not meet all specification listed.
3. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
4. In this datasheet, all the test methods of indications are based on corporate standards.
5. Only typical models listed, other models may be different, please contact our technical person for more details.
The copyright and authority for the interpretation of the products are reserved by Mornsun
Specifications subject to change without notice.
MSA_((M)D-3W&MSB_(M)D-3W
A/2-2009
Page 3 of 3