MURATA-PS D1U-W-2000-48-HA2C

D1U-W-2000-48-Hx Series
AC/DC Front End Power Supply + S1U Power Shelf
PRODUCT OVERVIEW
The D1U-W-2000 is a 2000 Watt, power-factor-corrected (PFC) front-end power supply for hot-swapping redundant
systems. The main output is 48V and standby output of either 5V or 3.3V. Packaged in 1U low profile, it is designed
to deliver reliable bulk power to servers, workstations, storage systems or any 48V distributed power architecture
systems requiring high power density. The highly efficient electrical and thermal design with internal cooling fans
supports reliable operation conditions. The D1U-W-2000 is designed to auto-recover from over-temperature faults.
Status information is provided with front panel LEDs, logic signals and I2C management interface. Three units can be
packaged into an optional 19” 1U power shelf to provide up to 6.0kW of power.
The S1U-X3 is a 1U x 19” EIA Rack Mount Power Shelf designed for holding three D1U Front End Power Supplies
in current sharing applications. It is intended for distributed power architecture applications in the Servers, Storage
Networking and Data Communications markets. There are two lug terminal connections for #2 AWG cabling for the DC
output. System connection through the I2C bus reports the performance status of the power supplies within the power
shelf. Two Power Shelves can operate in parallel by an optional Shelf-to-Shelf cable, doubling the power output to the
maximum capability of 12kW for two 48V power shelves.
SELECTION GUIDE
FEATURES
Part Number
RoHS compliant
D1U-W-2000-48-HC2C
D1U-W-2000-48-HA2C
D1U-W-2000-48-HB2C
2000W (220Vac), 1200W (110Vac)
Output power
48V Main output,
3.3V, 5V or 12V standby output
1U sized; dimensions 12” x 4.75” x 1.6”
21.9 Watts per cubic inch density
N+1 redundancy capable,
including hot-docking
Active current sharing on main output
Over-voltage, over-current,
over-temperature protection
Internal cooling fans
Power Output
High Line AC
Power Output
Low Line AC
Main Output
Standby
Output
Airflow
2000W
2000W
2000W
1200W
1200W
1200W
48V
48V
48V
3.3V
5V
12V
Back to front
Back to front
Back to front
Part Number
Description
S1U-3X-16-A-48-RC
Power shelf for 48V D1U
INPUT CHARACTERISTICS
Parameter
Conditions
Min.
Input Voltage Operating Range
Low Line AC
High Line AC
90
180
47
78.5
70.5
Input Frequency
Turn-on Input Voltage
Turn-off Input Voltage
Maximum Input Current
Inrush Current
Power Factor
Ramp up
Ramp down
Low Line AC 90Vac
High Line AC 180Vac
Cold start between 0-1msec
Output load >90%
Output load >50%
I²C Bus Interface with status indicators
OUTPUT VOLTAGE CHARACTERISTICS
Optional 1U x 19” power-shelf
Output
Voltage
48V
3.3Vsb
5Vsb
12Vsb
www.murata-ps.com
Parameter
Voltage Set Point Accuracy
Line and Load Regulation
Ripple Voltage & Noise1
Output Current
Load Capacitance
Voltage Set Point Accuracy
Line and Load Regulation
Ripple Voltage & Noise1
Operating Range
Load Capacitance
Voltage Set Point Accuracy
Line and Load Regulation
Ripple Voltage & Noise1
Operating Range
Load Capacitance
Voltage Set Point Accuracy
Line and Load Regulation
Ripple Voltage & Noise1
Operating Range
Load Capacitance
Conditions
Typ.
50/60
Max.
140
264
63
86.5
78
15
10
90
Units
Vac
Hz
Vac
Arms
Apk
95%
75%
Min.
Typ.
Max.
48
46.54
20MHz Bandwidth
2
20MHz Bandwidth
0
mV p-p
A
μF
3.4
50
4.5
1530
mV p-p
A
μF
5
4.85
5.15
50
4
1530
20MHz Bandwidth
0
12
11.2
20MHz Bandwidth
0
Vdc
49.44
480
41.3
10000
3.3
3.2
Units
12.4
120
1.7
1530
Vdc
Vdc
mV p-p
A
μF
Vdc
mV p-p
A
μF
Technical enquiries email: [email protected], tel: +1 (866) 740 1232
CPS_D1U-W-2000-48-Hx.C06 Page 1 of 7
D1U-W-2000-48-Hx Series
AC/DC Front End Power Supply + S1U Power Shelf
OUTPUT CHARACTERISTICS
Parameter
Conditions
Remote Sense
Efficiency
Output Rise Monotonicity
240
220Vac
90.6
Overshoot less than 10% for all outputs, no voltage negative between 10% to 95% during ramp up
AC ramp up
1.5
PS_On activated
150
48V Ramp 1A/μs, 50% load step
±2700
3.3Vsb Ramp 1A/μs, 50% load step
±165
5Vsb Ramp 1A/μs, 50% load step
±250
12Vsb Ramp 1A/μs, 50% load step
±600
Start-up Time
Transient Response
Current sharing accuracy (up to 6 in parallel)
At 100% load
Hot Swap Transients
Hold-up Time
All outputs within regulation
Max. load, nominal Vin
Min.
Typ.
Max.
±10
17
Units
mV
%
s
ms
mV
%
ms
GENERAL CHARACTERISTICS
Parameter
Conditions
Min.
Storage Temperature Range
Operating Temperature Range
Operating Humidity
Storage Humidity
Shock
Sinusoidal Vibration
Non-condensing
-40
0
10
5
Non-condensing
Typ.
70
50
90
90
Safety Approvals
30G non operating
0.5G, 5 – 500 Hz operating
Calculated per Bellcore at Ta=30°C
200
Demonstrated
200
ISO 7779-1999
c-CSA-us (CSA 60950-1-03/UL 60950-1, First Edition)
TUV approval (Bauart) EN 60950-1:2001
Input Fuse
Material Flammability
Power Supply has internal 20A/250V fast blow fuse on the AC line input
UL 94V-0
Switching Frequency
90KHz for Boost PFC Converter
165KHz for Main Output Converter
200KHz for Standby Output Converter
Weight
2.1kg
MTBF
Acoustic
Max.
Units
°C
%
60
Khrs
Khrs
dB LpAm
Max.
Units
65
59
50
14
3
4.02
8
6
7
°C
V
A
V
A
V
A
V
A
PROTECTION CHARACTERISTICS
Output
Voltage
48V
12Vsb
3.3Vsb
5Vsb
Parameter
Conditions
Min.
Over-temperature
Over Voltage
Over Current
Over Voltage
Over Current
Over Voltage
Over Current
Over Voltage
Over Current
Auto-restart
Latching
Latching
Latching
Latching
Latching
Latching
Latching
Latching
55
54
44
13
2.5
3.57
6.5
5.6
5
Typ.
1
Ripple and noise are measured with 0.1 uF of ceramic capacitance and 10 uF of tantalum capacitance on each of the power supply outputs. The output noise requirements apply
over a 0 Hz to 20 MHz bandwidth. A short coaxial cable with 50ohm scope termination is used.
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 (866) 740 1232
CPS_D1U-W-2000-48-Hx.C06 Page 2 of 7
D1U-W-2000-48-Hx Series
AC/DC Front End Power Supply + S1U Power Shelf
ISOLATION CHARACTERISTICS
Parameter
Insulation Safety Rating / Test Voltage
Isolation
Material Flammability
Grounding
Conditions
Min.
Typ.
Max.
Units
Input to Output - Reinforced
3000
Vrms
Input to Chassis - Basic
1500
Vrms
Output to Chassis
Output to Output
UL 94V-0
Main Output Return and Standby Output Return are connected internally. 100kΩ resistor parallel with 100nF
capacitor is connected between Return and power supply chassis. Main Output Return should be connected to
the System Chassis.
CONTROL SIGNALS
Status
Conditions
Description
LED
Off
Flashing Yellow
Flashing Green
Green
No AC input to all PS
Power Supply Failure
Main Output Absent
Power Supply Good
Status
PS-ON, PGOOD, ACOK, PS_BAD, FANFAIL, OT Warning &
shutdown, AC Range
Output Fault
48V Output
48V
Fan1 Monitor
Fan2 Monitor
48V OV, 48V UV, 48V OC, Vsb Fail, Fan1 Fail, Fan2 Fail
8 bit scaled output voltage
8 bit scaled output current
8 bit scaled output current
8 bit scaled output current
I2C Registers
EMISSIONS AND IMMUNITY
Characteristic
Description
Harmonics
Voltage Fluctuation and Flicker
Emission Conducted
Emission Radiated
IEC/EN 61000-3-2
IEC/EN 61000-3-3
FCC 47 CFR Parts 15/CISPR 22/EN55022
FCC 47 CFR Parts 15/CISPR 22/EN55022
ESD
IEC/EN 61000-4-2
Electromagnetic Field
Electrical Fast Transients/Burst
Surge
RF Conducted Immunity
Magnetic Immunity
Voltage dips, interruptions
IEC/EN 61000-4-3
IEC/EN 61000-4-4
IEC/EN 61000-4-5
IEC/EN 61000-4-6
IEC/EN 61000-4-8
IEC/EN 61000-4-11
www.murata-ps.com
Criteria
Class A, 6dB margin
Class A, 6dB margin
4kV contact discharge
8kV operational air discharge
15kV non-operational air discharge
1kV/2kV, Performance Criteria B
3 Vac, 80% AM, 1kHz, Performance Criteria A
3 A/m
Technical enquiries email: [email protected], tel: +1 (866) 740 1232
CPS_D1U-W-2000-48-Hx.C06 Page 3 of 7
D1U-W-2000-48-Hx Series
AC/DC Front End Power Supply + S1U Power Shelf
OUTPUT CONNECTOR AND SIGNAL SPECIFICATION
DC and Signal Connector: Tyco Part # 1-6450332-7, or FCI PowerBlade # 51732-028
P1
P2
VOUT
VOUT
P3
P4
VOUT
VRTN
P5
VRTN
P6
x1
x2
x3
x4
x5
AC_OK
P_GOOD
V_SB
+OUT
V_SB
RETURN
V_SB
RETURN
D
PS_ON
V_SB
+OUT
V_SB
+OUT
V_SB
RETURN
V_SB
RETURN
C
I_SHARE
I2C ADR0
I2C ADR1
I2C ADR2
PS_
PRESENT
B
PS_KILL
VOUT
SENSE+
VOUT
SENSE-
I2C DATA
I2C
CLOCK
A
VRTN
High Level
Low Level
I Max
Main output voltage
Main output voltage, return
VOUT remote sense, positive node input, connected to the
+ve load point
VOUT remote sense, negative node input, connected to the
-ve load point
Standby voltage output
Standby voltage, return, tied internally to Output Return
Active load sharing bus
0 – 8V
-4 mA / +5 mA
>2.4V (active, OK)
<0.4V
+4 mA
-2 mA
Pin Assignment
Signal Name
Description
P1, P2, P3
P4, P5, P6
VOUT
VRTN
A1
Sense +
A2
Sense -
C5, C6, D5, D6
C3, C4, D3, D4
B1
V_SB
V_SB Return
I_Share
D1
AC_OK
Input AC Voltage “OK” signal output (Internal pull up is
10kΩ to Vsb)
D2
P_Good
Power good signal output (Internal pull up is 10kΩ to Vsb)
>2.4V (active, Good)
<0.4V
+4 mA
-2 mA
B5
PS_Kill
Floating pin will turn off P/S (shorter pin, last-make and
first-break contact for hot plugging). This signal overrides
PS-On in disabling the Main Output
>2.1V (open, or Vsb)
<0.7V (active, PS:On)
N/A
B6
PS_Present
Internally tied to Vsb return
0V
A6
PS_On
Internal 1K ohm pull-up to Vsb, (accepts open collector/
drain drive), This signal to be pulled low to turn-on power
supply
>2.1V (open, or Vsb)
<0.7V (active, PS:On)
A3
A4
I2C Data
I2C Clock
I2C serial data bus
I2C serial clock bus
B2
I2C Adr0
Address input 0, internal pull-up to Vsb
B3
I2C Adr1
Address input 1, internal pull-up to Vsb
B4
I2C Adr2
Address input 2, internal pull-up to Vsb
Vsb
Vsb
>2.1V, < Vsb
<0.8V
>2.1V, <Vsb
<0.8V
>2.1V, <Vsb
<0.8V
-4 mA
-1 mA
±1 mA
±1 mA
±1 mA
D1U MATING CONNECTORS
2
Solder 2
Press Fit
48V D1U mating connector
Straight
Right Angle
Straight
Right Angle
MPS
FCI
N/A
51742-10602000CALF
Pending
51762-10602000CBLF
N/A
51742-10602000AALF
36-0440026-0
51762-10602000ABLF
Tyco
TBD
TBD
TBD
TBD
Solder connector recommended for board thickness of <0.090
www.murata-ps.com
Technical enquiries email: [email protected], tel: +1 (866) 740 1232
CPS_D1U-W-2000-48-Hx.C06 Page 4 of 7
D1U-W-2000-48-Hx Series
AC/DC Front End Power Supply + S1U Power Shelf
CONNECTOR TO CUSTOMER SYSTEM
Signal Connector: MOLEX # 39-28-5204 OR TYCO # 281282-1
Mating Connector: MOLEX # 0039521204
Pin Assignment
Signal Name
Description
1
AC_OK11
Input AC Voltage ‘OK’ signal output for the 2nd shelf
2
P_Good12
Power good signal output for the 2nd shelf
3
PS_On13
Power enable for the 2nd shelf
4
NOT USED
5
AC_OK01
Input AC Voltage “OK” signal output for the local shelf
6
P_Good02
Power good signal output for the local shelf
7
PS_OnO3
Power enable for the local shelf
8
NOT USED
9
I2C Adr2
2
10
11
12
13
14
15
16
17
18
19
20
Address input 2
4
I C Clock
I2C Data4
I_SHARE
SENSE +5
SENSE -5
Vsb
Vsb
Vsb
GND
GND
GND
2
I C serial clock bus
I2C serial data bus
High Level
Low Level
I Max
open drain
< 0.7V
open drain
< 0.7V
> 2.1V (open, or Vsb)
< 0.7V (active, PS:On)
- 2 mA
+ 4 mA
- 2 mA
+ 4 mA
- 1 mA
- 4 mA
open drain
< 0.7V
open drain
< 0.7V
> 2.1V (open, or Vsb)
< 0.7V (active, PS:On)
- 2 mA
+ 4 mA
- 2 mA
+ 4 mA
- 1 mA
- 4 mA
> 2.1V, < Vsb
< 0.8V
Vsb
Vsb
± 1 mA
Standby voltage output
Standby voltage output
Standby voltage output
GROUND
GROUND
GROUND
All control signals are with respect to Ground. Negative currents exit the power supply.
1
Signal goes low when any one of the three power supplies loses AC
Signal goes low when any one of the three power supplies fail
In a standalone shelf (without I2C control) Pull this pin to GND to turn on three power supplies at the same time. With I2C control, leave this signal float and Use I2C to turn on one power supply at a time.
4
Recomended 10KOhm pull up resistor to host 3.3 or 5V rail
5
Short Sense+ to +Vout and Sens- to GND at the point of load
2
3
SHELF TO SHELF CONNECTION
Signal Connector: MOLEX # 39-28-5164 OR TYCO # 281281-1
Pin Assignment
Signal Name
Description
1
AC_OK11
Input AC Voltage ‘OK’ signal output for the 2nd shelf
2
P_Good12
Power good signal output for the 2nd shelf
3
PS_On13
Power enable for the 2nd shelf
4
5
6
7
8
9
10
11
12
13
14
15
16
NOT USED
NOT USED
I2C Clock4
I2C Data4
I_SHARE
SENSE +5
SENSE -5
Vsb
Vsb
Vsb
GND
GND
GND
www.murata-ps.com
I2C serial clock bus
I2C serial data bus
High Level
Low Level
I Max
open drain
< 0.7V
open drain
< 0.7V
> 2.1V (open, or Vsb)
< 0.7V (active, PS:On)
- 2 mA
+ 4 mA
- 2 mA
+ 4 mA
- 1 mA
- 4 mA
Vsb
Vsb
Standby voltage output
Standby voltage output
Standby voltage output
GROUND
GROUND
GROUND
Technical enquiries email: [email protected], tel: +1 (866) 740 1232
CPS_D1U-W-2000-48-Hx.C06 Page 5 of 7
D1U-W-2000-48-Hx Series
AC/DC Front End Power Supply + S1U Power Shelf
MECHANICAL DIMENSIONS - D1U-W-2000-48-Hx
312,89 ±0,35
[ 12.319 ±0.013 ]
20,20 ±0,40
[ 0.795 ±0.015 ]
8,89
[ 0.350 ]
REF
37,31 ±0,40
[ 1.469 ±0.015 ]
132,85 ±0,50
[ 5.230 ±0.019 ]
127,85 ±0,40
[ 5.033 ±0.015 ]
120,65 ±0,65
[ 4.750 ±0.025 ]
304,80 ±0,65
[ 12.000 ±0.025 ]
12,63 ±0,40
[ 0.497 ±0.015 ]
41.00±040
[1.614±0.015]
AC Input Connector: The AC input connector is standard IEC320 C20 (20A)
Dimensions: 12.00”L x 4.75” W x 1.6” H (40.7H x 120.6W x 304.90mm)
MECHANICAL DIMENSIONS - S1U Power Shelf
1.709
(43.40)
0.228
(5.80)
1.252
(31.80)
15.937
(404.80)
17.315
(439.80)
www.murata-ps.com
18.307
(465.00)
18.992
(482.40)
NOTES:
1. The DC output terminals are of terminal block style that will allow connection using crimp
type right-angle lugs accepting up to AWG#2 wire, Panduit lug LCC2-14AWF-Q or equivalent is
recommended.
2. Two M6 studs at 15.88 mm centre spacing are provided for connection to each pole. Hardware is
provided for fastening the lugs/wires as well as terminal block covers
Technical enquiries email: [email protected], tel: +1 (866) 740 1232
CPS_D1U-W-2000-48-Hx.C06 Page 6 of 7
D1U-W-2000-48-Hx Series
AC/DC Front End Power Supply + S1U Power Shelf
S1U PIN CONNECTORS - BACK VIEW
48V+ OUTPUT
48V+ OUTPUT
PIN #1
PIN #1
GND
GND
J2 SIGNAL CONNECTOR
FOR SHELF-TO-SHELF CONNECTION
USE CABLE P/N 535-413-1537-1
J1 SIGNAL CONNECTOR
TO CUSTOMER SYSTEM
SHELF TO SHELF CONNECTION
J1 SIGNAL CONNECTOR
TO CUSTOMER SYSTEM
J2 TO J1 RIBBON CABLE
P/N 535-413-1537
( REPEAT THIS CONNECTION
FOR ADDITIONAL SHELVES. )
OPTIONAL ACCESSORIES
Description
Part Number
48V D1U output connector card
D1U-48-CONC
Shelf to shelf cable
535-413-1537
APPLICATION NOTES
Document Number
Description
ACAN-29
D1U Communication Protocol
USA:
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356
www.murata-ps.com email: [email protected] ISO 9001 REGISTERED
01/15/09
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
notice.
© 2009 Murata Power Solutions, Inc.
www.murata-ps.com
Mansfield (MA), Tel: (508) 339-3000, email: [email protected]
Canada:
Toronto, Tel: (866) 740-1232, email: [email protected]
UK:
Milton Keynes, Tel: +44 (0)1908 615232, email: [email protected]
France:
Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: [email protected]
Germany:
München, Tel: +49 (0)89-544334-0, email: [email protected]
Japan:
Tokyo, Tel: 3-3779-1031, email: [email protected]
Osaka, Tel: 6-6354-2025, email: [email protected]
China:
Shanghai, Tel: +86 215 027 3678, email: [email protected]
Guangzhou, Tel: +86 208 221 8066, email: [email protected]
Singapore:
Parkway Centre, Tel: +65 6348 9096, email: [email protected]
Technical enquiries email: [email protected], tel: +1 (866) 740 1232
CPS_D1U-W-2000-48-Hx.C06 Page 7 of 7