FMV-595 Duplex V/Duplex A & D Two-way Video with One Duplex Audio and One Duplex Data The FMV-595 is a duplex Video transmission system with one duplex Audio and one Data port, ideal for CCTV cameras and traffic surveillance. Status indicators on Video, Sync, Data, carrier detect, voltage, temperature, and optical levels are monitored via LEDs. Video Audio System Design All of our units come as an Insert Card version. The cards can be inserted into our 18-slot, 19” rackmountable card cage (CC-18-80W), or one of our smaller Desk Top Card Racks (DTCR series). Data The Desk Top Card Racks can handle one, two, four, or seven cards, allowing for greater flexibility and future expansion. They can sit on a flat surface as a larger stand-alone unit, or can be surface mounted with the flanges provided. Each one of our card housings operates with an appropriate power supply. The regulated switching power supply has short circuit protection and an input operating voltage of 87- 264 VAC. 865 1310 ● ● ● ● ● 1550 Type Mode Wavelength Suffix LED MM L0/L1 Features • Multimode or singlemode operation over one fiber • 8 MHz video bandwidth • 10 Hz to 20 KHz audio bandwidth • True DC restoration • Flat frequency response • Complies with RS-170 and RS-170A EIA video standards • Compatible with NTSC, PAL and SECAM • No EMI or RFI and no ground loops • Stand Alone or Rack Mount • Ideal for CCTV cameras, video conferencing and ITS Fiber Type 50 /125µ Output Power Receiver Sensitivity Optical Loss Budget Range* Conn Type -16 dBm -34 dBm 18 dB 3 km ST -10 dBm -34 dBm 24 dB 25 km FC 62.5/125µ ● Laser SM L2/L3 09/125µ * Chromatic dispersion should be taken into account. 96 800-867-8426 • [email protected] • www.opticomm.com • Contact factory for higher requirement. CCTV Security Networking Video Video in/out impedance Video in/out level Video bandwidth Differential gain Differential phase Linearity Tilt Compatibility Signal to noise ratio FM carrier frequency Connector type Audio Audio in/out impedance Audio in/out level Frequency response Signal to noise ratio Total harmonic distortion Connector type Data Data rate Bit error rate Data formats available Connector type General Dimensions & Weight Temperature Humidity Operating voltage Vibration/Shock Diagnostics Status monitoring 75 Ω 1 volt peak to peak, 1.5 volts max 5 Hz to 8 MHz @ -3dB < 1.0 % typical < 1.0° typical ± 1.1 % typical ≤ 0.5 % typical NTSC, PAL, SECAM, RS-170, RS-170A >67 dB using RS-250C standards @ 1 km 70 MHz BNC Selection Guide Digital Broadcast AM/IM Analog SWFM SWFM Analog Analog Analog-to-Digital RGB Video Datacom RF CATV 600 Ω (balanced) or 10 kΩ (unbalanced) -6 to +6 dBm 10 Hz to 20 KHz > 60 dB < 1.0 %, 1 KHz at maximum modulation Hi-density 15 pin DB9 (DE15) DC to 300 Kbps 10-9 Async Rs-232, RS-422, RC-485/2W, Glenlock, Manchester, 20 mA current loop, TTL, or six Contact Closures Hi-density 15 pin DB9 (DE15) Stand Alone (SA): 7.16” L x 5.21” W x .94” H 39 oz Insert Card (IC): 6.3” L x 0.8” W x 4.0” H 16 oz Operating: -40° C to +74° C; Storage; -55° C to +85° C 0 to 95% non-condensing 12 VDC (200 mA) or 9-24 VAC (300mA) or 110/220 VAC Up to 5 g's/Up to 12 g's LED indicator Appendix Opticomm reserves the right to change product specifications without notice. Emissions: FCC Part 15, ICES-003, AS/NZS, 3548, EN55022 Immunity: ENVS0204, EN61000-4-2,3,4,5,6,11 Safety: UL1950, CAN/CSA 22.2, NO.950-95 MADE IN THE USA Sample Configuration 97