14 Pin DIL Triple TTL Compatible Active Delay Lines DELAY TIME ±5% or 2 nS† PART NUMBER DELAY TIME ±5 or 2 nS† PART NUMBER DELAY TIME ±5% or 2 nS† PART NUMBER 5 6 7 8 9 10 11 12 13 14 15 16 17 18 EPA189-5 EPA198-6 EPA189-7 EPA189-8 EPA189-9 EPA18910 EPA189-11 EPA189-12 EPA189-13 EPA189-14 EPA189-15 EPA189-16 EPA189-17 EPA189-18 19 20 21 22 23 24 25 30 35 40 45 50 55 60 EPA189-19 EPA189-20 EPA189-21 EPA189-22 EPA189-23 EPA189-24 EPA189-25 EPA189-30 EPA189-35 EPA189-40 EPA189-45 EPA189-50 EPA189-55 EPA189-60 65 70 75 80 85 90 95 100 125 150 175 200 225 250 EPA189-65 EPA189-70 EPA189-75 EPA189-80 EPA189-85 EPA189-90 EPA189-95 EPA189-100 EPA189-125 EPA189-150 EPA189-175 EPA189-200 EPA189-225 EPA189-250 †Whichever is greater. Delay Times referenced from input to leading edges at 25°C, 5.0V, with no load. DC Electrical Characteristics Parameter VOH VOL VIK IIH High-Level Output Voltage Low-Level Output Voltage Input Clamp Voltage High-Level Input Current IIL IOS Low-Level Input Current Short Circuit Output Current ICCH ICCL TRO NH NL High-Level Supply Current Low-Level Supply Current Output Rise Time Fanout High-Level Output Fanout Low-Level Output Schematic Test Conditions VCC = min. VIL = max. I OH = max VCC = min. VIH = min. I OL= max VCC = min. II = II K VCC = max. VIN = 2.7V VCC = max. VIN = 5.25V VCC = max. VIN = 0.5V VCC = max. VOUT = 0. (One output at a time) VCC = max. VIN = OPEN VCC = max. VIN = 0 Td ≤ 500 nS (0.75 to 2.4 Volts) VCC = max. VOH = 2.7V VCC = max. VOL = 0.5V Recommended Operating Conditions VCC VIH VIL IIK IOH IOL PW* d* TA Min Max Unit Supply Voltage High-Level Input Voltage Low-Level Input Voltage Input Clamp Current High-Level Output Current Low-Level Output Current Pulse Width of Total Delay Duty Cycle Operating Free-Air Temperature 2.7 -40 0.5 -1.2V 50 1.0 -2 -100 V V V µA mA mA mA 115 mA 115 mA 4 nS 20 TTL LOAD 10 TTL LOAD 14 1 Max Unit 4.75 2.0 5.25 V V V mA mA mA % % °C 0.8 -18 -1.0 20 40 0 40 +70 3 5 7 GROUND White Dot Pin#1 PCA EPA189-5 Date Code Unit 3.2 110 2.0 1.0 100 5.0 Volts % nS MHz KHz Volts .400 Max. .800 Max. .020 Typ. .275 Max. Input Pulse Test Conditions @ 25° C VCC 10 8 .018 Pulse Input Voltage Pulse Width % of Total Delay Pulse Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ Td ≤ 200 nS Pulse Repetition Rate @ Td > 200 nS Supply Voltage 12 Package Dimensions Min *These two values are inter-dependent. EIN PW TRI PRR VCC .150 Typ. .200 .010 .300