POMONA 6086

Model 6086
ESD Wrist Strap Tester
FEATURES:
Touch type on-demand tester and common point
ground
Test any wrist strap connected to utility ground with a
simple touch
Tester has two Banana Plug Sockets for Wrist Strap
cord attachments
Once connected, the user simply touches the unit and a
green light and audible sound indicate a proper ground
Audible indicator has selectable on or off
Tester can be mounted near your work area with
Velcro® strips or, using an integral button 10mm snap
stud, attached directly to your static-safe work mat.
Powered by a 120 VAC wall adapter, the tester has a
“Power on” indicator
It is practical for both a quick test or as a continuous
ground point connection
UL listed
MATERIALS:
Wrist Tester:
Snap Socket (Rear): 10mm (.39), Nickel Plated
Banana Plug Sockets: Nickel Plated
AC Adapter Jack: Nickel Plated
AC Adapter: 120 VAC wall adapter (12 VDC Power Supply)
Velcro Strip: Adhesive backed hook and loop mounting pads
ORDERING INFORMATION: Model 6086
All dimensions are in inches. Tolerances (except noted): .xx = ±.02” (,51 mm), .xxx = ± .005” (,127 mm).
All specifications are to the latest revisions. Specifications are subject to change without notice.
Registered trademarks are the property of their respective companies.
Sales: 800-490-2361 Fax: 888-403-3360 Technical Support: 800-241-2060 ([email protected])
For “Where to Buy” information, visit the Pomona web site at www.pomonaelectronics.com
Rev: 100
D1094536
Page 1 of 3
Model 6086
ESD Wrist Strap Tester
Packaging: One tester, AC Adapter, two Velcro pads, and instruction sheets.
All dimensions are in inches. Tolerances (except noted): .xx = ±.02” (,51 mm), .xxx = ± .005” (,127 mm).
All specifications are to the latest revisions. Specifications are subject to change without notice.
Registered trademarks are the property of their respective companies.
Sales: 800-490-2361 Fax: 888-403-3360 Technical Support: 800-241-2060 ([email protected])
For “Where to Buy” information, visit the Pomona web site at www.pomonaelectronics.com
Rev: 100
D1094536
Page 2 of 3
Model 6086
ESD Wrist Strap Tester
CALIBRATION:
Calibration of Pomona model 6086 is recommended annually. Calibration should be performed to ensure that
the tester is operating within limits. The calibration may be checked with discrete resistors.
Resistance Value (+/- 10%)
675 KOhms
825 KOhms
8.5 MOhms
11.5 MOhms
Test Display
Red (Low-hazard)
Green (OK-in limits)
Green (OK-in limits)
Red (High resistance)
To calibrate, simple place each resistance value (see table) between the touch plate and banana jack grounds.
Observe that the proper test display LED is on (see table) for the selected resistor. Be sure to hold the test cord
at an insulated point, so the resistance value in not affected by the body. There are no adjustments inside.
All dimensions are in inches. Tolerances (except noted): .xx = ±.02” (,51 mm), .xxx = ± .005” (,127 mm).
All specifications are to the latest revisions. Specifications are subject to change without notice.
Registered trademarks are the property of their respective companies.
Sales: 800-490-2361 Fax: 888-403-3360 Technical Support: 800-241-2060 ([email protected])
For “Where to Buy” information, visit the Pomona web site at www.pomonaelectronics.com
Rev: 100
D1094536
Page 3 of 3