DC-AC INVERTER UNIT PS-M05D12S3-NJ4L-012(S) (6,5 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile DC to AC Inverter is developed for dual lamps. Optimized for Sharp: LQ064V3DG01 APPLICABLE LCD: 6.4 to 12 inches double lamp type Lamp Current 5 mArms Lamp Start Up Voltage 900 Vrms (Vin : 12 Vdc) FEATURES : Remote ON/OFF Ext. PWM-Dimming Function RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity LxWxH 82 ± 0.3 13 ± 0.5 PS-MXXDXX-NJX 29/01/2004 MADE IN GERMANY CN1-1 CN2 (2) CN1 15 ± 0.3 22,5 ± 0.5 105 x 22,5 x 10mm 105 ± 0.5 5 ± 0.5 DIMENSIONS : 0°C ~ +60°C -20°C ~ +85°C 95 %RH max CAUTION HIGH VOLTAGE CN2-1 CN1-5 10.0MAX CN2-4 3 2 - Ø2.5 ± 0.2 (for M2 screws) 2 (2) 1 Unit : mm Weight :20 (g) typ. High Voltage generation area 60mm Note: Please use plastic screw in case of a non-insulating mounting base! Components No. 1 2 3 Part Description PCB Connector CN1 Connector CN2 Input side CN1: Pin No. Symbols Vin CN 1-1 GND CN 1-2 CN 1-3 Ext. PWM N.C. CN 1-4 CN 1-5 Vrm t Qty. 1 1 1 Material UL94V-0 (FR-4 or CEM-3) S5B-PH-SM3 SM03(4.0)B-BHS Note t=1.6m m JST or equal JST or equal Output side CN2: Ratings 12 Vdc Pin No. CN 2-1+2 CN 2-3 Symbols VHIGH1 VLOW Ratings 520 Vrm s (5 m Arm s ) 0 Vdc 0 ~ 5 Vdc (L activ) 0 / 5 Vdc (H activ) Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 2.9.2 , 12th March 2007 DC-AC INVERTER UNIT PS-M05D12S3-NJ4L-012(S) (6,5 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) ELECTRICAL CHARACTERISTICS : Parameters Symbols Output Current Output Current Input Current Frequency Open Circuit Voltage Iout Iout Iin F Vopen Note 1 : Note 2: Note 3: Specification Min. Typ. Max. 4.5 4.0 45 1.100 5.0 5.0 0.7 55 - 5.5 6.0 1.2 65 - Unit Note m Arm s m Arm s Adc kHz Vrm s Duty 100% Please keep minimum of 2mm clearance (all directions) between inverter high voltage area as marked on mechanical drawing and any conductors. Remote ON/OFF (CN1-5) has priority and can not be used in combination with External PWM Dimming (CN1-3). When 'Ext.PWM' (CN1-3) is used 'Vrmt' (CN1-5) should not be connected. The external PWM frequency should be in a range of 100 ~ 500 Hz. For other frequency please request. The optimum is normally at 250 Hz, and minimizes the interference disturbances of the vertical sync. frequency. TEST CIRCUIT : Vin 12 V Conditions Vrmt Vin (V) Tu (°C) (V) 12±0.12 5±0.25 0 ~ +60 12±1.2 5±0.25 0 ~ +60 12±1.2 5±0.25 0 ~ +60 12±1.2 5±0.25 0 ~ +60 11,4 5±0.25 0 ~ +60 A F Iin 1000:1 PROBE F CN1-1 Vopen V ~ SW 1 SW3 V CN2-1 CN1-2 Operation of unit a Operation b Non operation SW4 CN1-3 T1 CN2-2 RL2 RL1 Ext. PWM* 0~5V CL2 A NC Vrmt 2.5 Vdc ~ Vin SW5 a V b CL1 A ~ Iout ~ Iout1 2 CN1-4 CN2-4 SW1 CN1-5 *) Only active when Vrmt is 0 Vdc or floating EXTERNAL PWM-DIMMING ( Remote ON / OFF Detailed Circuit Diagram ): Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 2.9.2 , 12th March 2007