PULSECORE I2042AG-08TT

P2042A
August 2007
rev 1.5
LCD Panel EMI Reduction IC
Features
interference (EMI) at the clock source, allowing system
wide reduction of EMI of
•
FCC approved method of EMI attenuation.
•
Provides up to 15dB of EMI suppression.
•
Generates a low EMI spread spectrum clock of
the input frequency.
Input frequency range: 30MHz to 110MHz.
•
Optimized for 32.5MHz, 54MHz, 65MHz and
108MHz pixel clock frequencies.
Internal loop filter minimizes external components
and board space.
•
Eight selectable high spread ranges up to ±
1.9%.
•
SSON# control pin for spread spectrum enable
and disable options.
layers ferrite beads,
shielding and other passive
regulations.
The P2042A uses the most efficient and optimized
modulation
profile
approved
by
the
FCC
and
is
implemented in a proprietary all digital method.
The P2042A modulates the output of a single PLL in
order to “spread” the bandwidth of a synthesized clock,
and more importantly, decreases the peak amplitudes of
•
Low cycle-to-cycle jitter.
•
3.3V ± 0.3V operating range.
•
Low power CMOS design.
•
Supports most mobile graphic accelerator and
its harmonics. This results in significantly lower system
EMI compared to the typical narrow band signal produced
LCD timing controller specifications.
•
cost savings by reducing the number of circuit board
components that are traditionally required to pass EMI
•
•
down stream clock and data
dependent signals. The P2042A allows significant system
Available in 8-pin SOIC and TSSOP Packages.
by oscillators and most frequency generators. Lowering
EMI by increasing a signal’s bandwidth is called ‘spread
spectrum clock generation’.
Product Description
Applications
The P2042A is a versatile spread spectrum frequency
The P2042A is targeted towards digital flat panel
modulator designed specifically for digital flat panel
applications for notebook PCs, palm-size PCs, office
applications.
automation equipments and LCD monitors.
The
P2042A
reduces
electromagnetic
Block Diagram
VDD
SR0 CP1 CP0 SSON#
PLL
Modulation
CLKIN
Frequency
Divider
Feedback
Divider
Phase
Detector
Loop
Filter
VCO
Output
Divider
ModOUT
VSS
PulseCore Semiconductor Corporation
1715 S. Bascom Ave Suite 200, Campbell, CA 95008 • Tel: 408-879-9077 • Fax: 408-879-9018
www.pulsecoresemi.com
Notice: The information in this document is subject to change without notice.
P2042A
August 2007
rev 1.5
Pin Configuration
CLKIN 1
8
CP0 2
VDD
7 SR0
P2042A
CP1 3
6
ModOUT
VSS 4
5
SSON#
Pin Description
Pin#
Pin
Name
Type
1
CLKIN
I
2
CP0
I
3
CP1
I
4
VSS
P
Ground to entire chip. Connect to system ground.
5
SSON#
I
Digital logic input used to enable Spread Spectrum function (Active LOW). Spread
Spectrum function enabled when LOW, disabled when HIGH.
This pin has an internal pull-low resistor.
6
ModOUT
O
Spread spectrum clock output.
7
SR0
I
Digital logic input used to select Spreading Range. This pin has an internal pull-up resistor.
8
VDD
P
Power supply for the entire chip
Description
External reference frequency input. Connect to externally generated reference signal.
Digital logic input used to select charge pump current. This pin has an internal pull-up
resistor. Refer Modulation Selection Table.
Digital logic input used to select charge pump current. This pin has an internal pull-up
resistor. Refer Modulation Selection Table.
Modulation Selection
CP0
CP1
SR0
0
0
0
0
Spreading Range (±%)
32.5MHz
54MHz
65MHz
81MHz
108MHz
0
0.56
1.05
1.00
0.98
0.80
0
1
1.94
1.68
1.56
1.48
1.22
1
0
1.36
1.05
1.00
0.92
0.67
0
1
1
1.92
1.68
1.56
1.48
1.06
1
0
0
1.24
0.81
0.66
0.40
0.27
1
0
1
1.91
1.29
1.02
0.74
0.43
1
1
0
0.91
0.45
0.34
0.05
0.15
1
1
1
1.47
0.71
0.54
0.36
0.21
LCD Panel EMI Reduction IC
Notice: The information in this document is subject to change without notice.
Modulation Rate
(KHz)
(FIN /40) * 62.49
KHz
2 of 9
P2042A
August 2007
rev 1.5
Spread Spectrum Selection
The Modulation Selection Table defines the possible spread spectrum options. The optimal setting should minimize system
EMI to the fullest without affecting system performance. The spreading is described as a percentage deviation of the center
frequency. (Note: The center frequency is the frequency of the external reference input on CLKIN, pin1).
For example, P2042A is designed for high-resolution, flat panel applications and is able to support an XGA (1024 x 768) flat
panel operating at 65MHz (FIN) clock speed. A spreading selection of CP0=0, CP1=1 and SR0=0 provides a percentage
deviation of ±1.00% from FIN. This results in the frequency on ModOUT being swept from 65.65 to 64.35MHz at a modulation
rate of 101.54KHz. Refer Modulation Selection Table. The example in the following illustration is a common EMI reduction
method for a notebook LCD panel and has already been implemented by most of the leading OEM and mobile graphic
accelerator manufacturers.
Application Schematic for Mobile LCD Graphics Controllers
+3.3V
65MHz from graphics accelerator
1 CLKIN
VDD
8
2 CP0
SR0
7
3 CP1
ModOUT 6
4 VSS
0.1µF
Modulated 65MHz signal with
±1.00% deviation and
modulation rate of 101.54KHz.
This signal is connected back to
the spread spectrum input pin
(SSIN) of the graphics
accelerator.
SSON# 5
P2042A
Digital control for the SS enable
or disable
LCD Panel EMI Reduction IC
Notice: The information in this document is subject to change without notice.
3 of 9
P2042A
August 2007
rev 1.5
Absolute Maximum Ratings
Symbol
Parameter
Rating
Unit
VDD, VIN
Voltage on any pin with respect to Ground
-0.5 to +4.6
V
Storage temperature
-65 to +125
°C
TA
Operating temperature
-40 to +85
°C
Ts
Max. Soldering Temperature (10 sec)
260
°C
TJ
Junction Temperature
150
°C
TDV
Static Discharge Voltage (As per JEDEC STD22- A114-B)
2
KV
TSTG
Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect
device reliability.
Operating Conditions
Symbol
VDD
TA
TJ
θJC
Parameter
Supply Voltage with respect to Ground
Operating
temperature
Junction
temperature
Commercial
Industrial
Commercial
Industrial
Min
Typ
Max
Unit
3.0
3.3
3.6
V
0
+70
-40
+85
SOIC
°C
82.39
TSSOP
79.8
SOIC
TSSOP
97.39
94.8
SOIC
156.5
TSSOP
124
LCD Panel EMI Reduction IC
Notice: The information in this document is subject to change without notice.
°C
°C/W
4 of 9
P2042A
August 2007
rev 1.5
DC Electrical Characteristics
Symbol
Parameter
VIL
Input low voltage
VIH
Input high voltage
Input low current
(pull-up resistor on inputs CP0, CP1 and SR0)
Input high current (pull-down resistor on input SSON#)
IIL
IIH
VOL
Output low voltage (VDD = 3.3 V, IOL = 20 mA)
VOH
Output high voltage (VDD = 3.3 V, IOL = 20 mA)
IDD
Static supply current standby mode
ICC
Dynamic supply current (3.3V and 10pF loading)
VDD
Operating voltage
tON
Power-up time (first locked cycle after power up)
ZOUT
Max
Unit
VSS - 0.3
Min
Typ
0.8
V
2.0
VDD + 0.3
V
-35
µA
35
µA
0.4
V
2.5
V
0.6
mA
9
16
22
mA
3.0
3.3
3.6
V
Clock output impedance
0.18
mS
50
Ω
AC Electrical Characteristics
Symbol
Min
Typ
Max
Unit
Input frequency
30
65
110
MHz
fOUT
Output frequency
30
65
110
MHz
tLH*
Output rise time (measured at 0.8V to 2.0V)
0.7
0.9
1.1
nS
tHL*
Output fall time (measured at 2.0V to 0.8V)
0.6
0.8
1.0
nS
tJC
Jitter (cycle to cycle)
360
pS
tD
Output duty cycle
55
%
fIN
Parameter
45
50
*tLH and tHL are measured into a capacitive load of 15pF
LCD Panel EMI Reduction IC
Notice: The information in this document is subject to change without notice.
5 of 9
P2042A
August 2007
rev 1.5
Package Information
8-lead SOIC Package
H
E
D
A2
A
C
A1
D
θ
e
L
B
Dimensions
Symbol
Inches
Min
Max
Millimeters
Min
Max
A1
0.004
0.010
0.10
0.25
A
0.053
0.069
1.35
1.75
A2
0.049
0.059
1.25
1.50
B
0.012
0.020
0.31
0.51
C
0.007
0.010
0.18
0.25
D
0.193 BSC
4.90 BSC
E
0.154 BSC
3.91 BSC
e
0.050 BSC
1.27 BSC
H
0.236 BSC
6.00 BSC
L
0.016
0.050
0.41
1.27
θ
0°
8°
0°
8°
LCD Panel EMI Reduction IC
Notice: The information in this document is subject to change without notice.
6 of 9
P2042A
August 2007
rev 1.5
8-lead TSSOP
H
E
D
A2
A
C
θ
e
A1
L
B
Dimensions
Symbol
Inches
Min
Millimeters
Max
A
Min
Max
0.043
1.10
A1
0.002
0.006
0.05
0.15
A2
0.033
0.037
0.85
0.95
B
0.008
0.012
0.19
0.30
c
0.004
0.008
0.09
0.20
D
0.114
0.122
2.90
3.10
E
0.169
0.177
4.30
4.50
e
0.026 BSC
0.65 BSC
H
0.252 BSC
6.40 BSC
L
0.020
0.028
0.50
0.70
θ
0°
8°
0°
8°
LCD Panel EMI Reduction IC
Notice: The information in this document is subject to change without notice.
7 of 9
P2042A
August 2007
rev 1.5
Ordering Information
Part Number
Marking
Package Type
Temperature
P2042AF-08ST
P2042AF
8-Pin SOIC, TUBE, Pb Free
Commercial
P2042AF-08SR
P2042AF
8-Pin SOIC, TAPE & REEL, Pb Free
Commercial
P2042AF-08TT
P2042AF
8-Pin TSSOP, TUBE, Pb Free
Commercial
P2042AF-08TR
P2042AF
8-Pin TSSOP, TAPE & REEL, Pb Free
Commercial
P2042AG-08ST
P2042AG
8-Pin SOIC, TUBE, Green
Commercial
P2042AG-08SR
P2042AG
8-Pin SOIC, TAPE & REEL, Green
Commercial
P2042AG-08TT
P2042AG
8-Pin TSSOP, TUBE, Green
Commercial
P2042AG-08TR
P2042AG
8-Pin TSSOP, TAPE & REEL, Green
I2042AF-08ST
I2042AF
8-Pin SOIC, TUBE, Pb Free
Commercial
Industrial
I2042AF-08SR
I2042AF
8-Pin SOIC, TAPE & REEL, Pb Free
Industrial
I2042AF-08TT
I2042AF
8-Pin TSSOP, TUBE, Pb Free
Industrial
I2042AF-08TR
I2042AF
8-Pin TSSOP, TAPE & REEL, Pb Free
Industrial
I2042AG-08ST
I2042AG
8-Pin SOIC, TUBE, Green
Industrial
I2042AG-08SR
I2042AG
8-Pin SOIC, TAPE & REEL, Green
Industrial
I2042AG-08TT
I2042AG
8-Pin TSSOP, TUBE, Green
Industrial
I2042AG-08TR
I2042AG
8-Pin TSSOP, TAPE & REEL, Green
Industrial
Device Ordering Information
P 2042 A
F-
8
ST
SR - SOIC, T/R
TT – TSSOP, TUBE
TR - TSSOP, T/R
ST – SOIC, TUBE
Pin Count
F = LEAD FREE AND RoHS COMPLIANT PART
G = GREEN PACKAGE, LEAD FREE, and RoHS
Deviation (%) and Spread option Identifier
DEVICE NUMBER
P = Commercial Temperature Range (0°C to 70°C)
I = Industrial Temperature Range (-40°C to 85°C)
Licensed under U.S Patent Nos 5,488,627 and 5,631,921
LCD Panel EMI Reduction IC
Notice: The information in this document is subject to change without notice.
8 of 9
P2042A
August 2007
rev 1.5
PulseCore Semiconductor Corporation
1715 S. Bascom Ave Suite 200
Campbell, CA 95008
Tel: 408-879-9077
Fax: 408-879-9018
www.pulsecoresemi.com
Copyright © PulseCore Semiconductor
All Rights Reserved
Part Number: P2042A
Document Version: 1.5
Note: This product utilizes US Patent # 6,646,463 Impedance Emulator Patent issued to PulseCore Semiconductor, dated 11-11-2003
© Copyright 2006 PulseCore Semiconductor Corporation. All rights reserved. Our logo and name are trademarks or registered
trademarks of PulseCore Semiconductor. All other brand and product names may be the trademarks of their respective
companies. PulseCore reserves the right to make changes to this document and its products at any time without notice.
PulseCore assumes no responsibility for any errors that may appear in this document. The data contained herein represents
PulseCore’s best data and/or estimates at the time of issuance. PulseCore reserves the right to change or correct this data at
any time, without notice. If the product described herein is under development, significant changes to these specifications are
possible. The information in this product data sheet is intended to be general descriptive information for potential customers
and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. PulseCore does
not assume any responsibility or liability arising out of the application or use of any product described herein, and disclaims
any express or implied warranties related to the sale and/or use of PulseCore products including liability or warranties related
to fitness for a particular purpose, merchantability, or infringement of any intellectual property rights, except as express agreed
to in PulseCore’s Terms and Conditions of Sale (which are available from PulseCore). All sales of PulseCore products are
made exclusively according to PulseCore’s Terms and Conditions of Sale. The purchase of products from PulseCore does not
convey a license under any patent rights, copyrights; mask works rights, trademarks, or any other intellectual property rights of
PulseCore or third parties. PulseCore does not authorize its products for use as critical components in life-supporting systems
where a malfunction or failure may reasonably be expected to result in significant injury to the user, and the inclusion of
PulseCore products in such life-supporting systems implies that the manufacturer assumes all risk of such use and agrees to
indemnify PulseCore against all claims arising from such use.
LCD Panel EMI Reduction IC
Notice: The information in this document is subject to change without notice.
9 of 9