P1707A February 2007 rev 1.3 Notebook LCD Panel EMI Reduction IC Features the clock source, allowing system wide reduction of EMI of down stream clock and data dependent signals. The • FCC approved method of EMI attenuation. • Generates a low EMI spread spectrum clock of the input frequency. • Optimized for frequency range from 60MHz to 175MHz. • Internal loop filter minimizes external components and board space. • Four selectable spread ranges. • Low inherent Cycle-to-cycle jitter. • 3.3V Operating Voltage. • Ultra-low power CMOS design. • • 14.85 mA @3.3V, 140MHz • 16.69 mA @3.3V, 162MHz • 17.78 mA @3.3V, 175MHz required to pass EMI regulations. The P1707A modulates the output of a single PLL in order decreases the peak amplitudes of its harmonics. This results in significantly lower system EMI compared to the typical narrow band signal produced by oscillators and most frequency generators. Lowering EMI by increasing a signal’s bandwidth is called ‘spread spectrum clock generation’. Supports notebook VGA and other LCD timing Pinout compatible to ICS MK1707 and Cypress SSON/SBM pin for Spread Spectrum On/Off and Standby Mode controls. • and other passive components that are traditionally importantly, CY25561/CY25560. • the number of circuit board layers ferrite beads, shielding to “spread” the bandwidth of a synthesized clock, and more controller applications. • P1707A allows significant system cost savings by reducing Available in 8-pin SOIC and TSSOP Packages. The P1707A uses the most efficient and optimized modulation profile approved by the FCC and is implemented in a proprietary all digital method. Applications The P1707A is targeted towards notebook LCD displays, and other displays using an LVDS interface, PC peripheral Product Description devices, and embedded systems. The P1707A is a versatile spread spectrum frequency modulator designed specifically for input clock frequencies. The P1707A reduces electromagnetic interference (EMI) at VDD SR0 SR1 SSON/SBM Block Diagram PLL Modulation CLKIN Frequency Divider Feedback Divider Phase Detector Loop Filter VCO Output Divider ModOUT VSS PulseCore Semiconductor Corporation 1715 S. Bascom Ave Suite 200, Campbell, CA 95008 • Tel: 408-879-9077 • Fax: 408-879-9018 www.pulsecoresemi.com Notice: The information in this document is subject to change without notice. P1707A February 2007 rev 1.2 Pin Configuration CLKIN 8 NC 7 SR0 3 6 SR1 ModOUT 4 5 SSON/SBM 1 VDD 2 VSS P1707A Pin Description Pin# Pin Name Type Description 1 CLKIN I Connect to externally generated clock signal. To put the part into standby mode, disable the input clock signal to this pin and pull SSON/SBM (pin 5) low. Refer Standby Mode Selection Table. 2 VDD P Connect to +3.3V. (Place a decoupling 0.1µF close to pin and ground) 3 VSS P Ground Connection. Connect to system ground. 4 ModOUT O Spread spectrum clock output. 5 SSON/SBM I 6 SR1 I 7 SR0 I 8 NC - Spread Spectrum On/Off and standby mode control. Refer Standby Mode Selection Table. This pin has an internal pull-up resistor. Digital logic input used to select Spreading Range. Refer Spread Spectrum Selection Table. This pin has an internal pull-up resistor. Digital logic input used to select Spreading Range. Refer Spread Spectrum Selection Table. This pin has an internal pull-up resistor. No connect. Standby Mode Selection CLKIN SSON/SBM Spread Spectrum ModOUT PLL Mode Disabled 0 N/A Disabled Disabled Standby Disabled 1 N/A Disabled Free Running Free Running Enabled 0 Off Reference Disabled Buffer out Enabled 1 On Normal Normal Normal Spread Range Selection SR1 SR0 Spreading Range Modulation Rate 0 0 ± 1.50% (FIN/80) * 34.72 KHz 0 1 ± 2.50% (FIN/80) * 34.72 KHz 1 0 ± 0.50% (FIN/80) * 34.72 KHz 1 1 ± 1.00% (FIN/80) * 34.72 KHz Notebook LCD Panel EMI Reduction IC Notice: The information in this document is subject to change without notice. 2 of 7 P1707A February 2007 rev 1.2 Absolute Maximum Ratings Symbol Parameter VDD, VIN TSTG Rating Unit Voltage on any pin with respect to Ground -0.5 to +4.6 V Storage temperature -65 to +125 °C TA Operating temperature -40 to +85 °C Ts Max. Soldering Temperature (10 sec) 260 °C TJ Junction Temperature 150 °C 2 KV Static Discharge Voltage TDV (As per JEDEC STD22- A114-B) Note: These are stress ratings only and are not implied for functional use. Exposure to absolute maximum ratings for prolonged periods of time may affect device reliability. DC Electrical Characteristics Symbol Parameter Min Typ Max Unit VIL Input low voltage VSS – 0.3 - 0.8 V VIH Input high voltage 2.0 - VDD+ 0.3 V IIL Input low current (pull-up resistors on inputs SR0, SR1 and SSON/SBM) - - -35 µA IIH Input high current - - 35 µA IXOL XOUT output low current ( VXOL @ 0.4V, VDD = 3.3V) - 3 - mA IXOH XOUT output high current ( VXOH @ 2.5V, VDD = 3.3V) - 3 - mA VOL Output low voltage VDD= 3.3V, IOL = 20mA - - 0.4 V VOH Output high voltage VDD = 3.3V, IOH = 20mA 2.5 - - V ICC Dynamic supply current normal mode 3.3V and 10pF loading 8.46 12 17.78 mA IDD Static supply current standby mode - 0.6 - mA 2.7 3.3 3.7 V Power up time (first locked clock cycle after power up) - 0.18 - mS Clock output impedance - 20 - Ω VDD Operating voltage tON ZOUT AC Electrical Characteristics Symbol Min Typ Max Unit Input frequency 60 - 175 MHz fOUT Output frequency 60 - 175 MHz tLH* Output rise time ( Measured from 0.8V to 2.0V ) 0.7 0.9 1.1 nS tHL* Output fall time ( Measured from 2.0V to 0.8V ) 0.6 0.8 1.0 nS tJC Jitter (Cycle to cycle) - - 360 pS tD Output duty cycle 45 50 55 % fIN Parameter *tLH and tHL are measured into a capacitive load of 15pF Notebook LCD Panel EMI Reduction IC Notice: The information in this document is subject to change without notice. 3 of 7 P1707A February 2007 rev 1.2 Package Information Mechanical Package Outline 8-Pin SOIC Package H E D A2 A C A1 D θ e L B Dimensions Symbol Inches Min Max Millimeters Min Max A1 0.004 0.010 0.10 0.25 A 0.053 0.069 1.35 1.75 A2 0.049 0.059 1.25 1.50 B 0.012 0.020 0.31 0.51 C 0.007 0.010 0.18 0.25 D 0.193 BSC 4.90 BSC E 0.154 BSC 3.91 BSC e 0.050 BSC 1.27 BSC H 0.236 BSC 6.00 BSC L 0.016 0.050 0.41 1.27 θ 0° 8° 0° 8° Note: Controlling dimensions are millimeters SOIC – 0.074 grams unit weight Notebook LCD Panel EMI Reduction IC Notice: The information in this document is subject to change without notice. 4 of 7 P1707A February 2007 rev 1.2 Mechanical Package Outline 8-Pin TSSOP H E D A2 A C θ e A1 L B Dimensions Symbol Inches Min Millimeters Max A Min Max 0.043 1.10 A1 0.002 0.006 0.05 0.15 A2 0.033 0.037 0.85 0.95 B 0.008 0.012 0.19 0.30 c 0.004 0.008 0.09 0.20 D 0.114 0.122 2.90 3.10 E 0.169 0.177 4.30 4.50 e 0.026 BSC 0.65 BSC H 0.252 BSC 6.40 BSC L 0.020 0.028 0.50 0.70 θ 0° 8° 0° 8° Note: Controlling dimensions are millimeters TSSOP – 0.034 grams unit weight Notebook LCD Panel EMI Reduction IC Notice: The information in this document is subject to change without notice. 5 of 7 P1707A February 2007 rev 1.2 Ordering Codes Part Number Marking Package Type P1707AF-08ST P1707AF 8-pin SOIC, Tube, Pb-Free P1707AF-08SR P1707AF 8-pin SOIC, Tape & Reel, Pb Free P1707AF-08TT P1707AF 8-pin TSSOP, Tube, Pb Free P1707AF-08TR P1707AF 8-pin TSSOP, Tape and Reel, Pb Free P1707AG-08ST P1707AG 8-pin SOIC, Tube, Green P1707AG-08SR P1707AG 8-pin SOIC, Tape & Reel, Green P1707AG-08TT P1707AG 8-pin TSSOP, Tube, Green P1707AG-08TR P1707AG 8-pin TSSOP, Tape and Reel, Green Qty per reel Temperature Commercial 2500 Commercial Commercial 2500 Commercial Commercial 2500 Commercial Commercial 2500 Commercial Device Ordering Information P 1 7 0 7 A G - 0 8 X X Package: ST – SOIC, TUBE SR - SOIC, T/R TT – TSSOP, TUBE TR - TSSOP, T/R PIN COUNT F = LEAD FREE AND RoHS COMPLIANT PART G = GREEN PACKAGE, LEAD FREE, and RoHS DEVICE NUMBER Flow: P = Commercial Temperature Range (0°C to 70°C) I = Industrial Temperature Range (-40°C to +85°C) A = Automotive Temperature Range (-40°C to +125°C) Licensed under U.S Patent Nos 5,488,627 and 5,631,921 Notebook LCD Panel EMI Reduction IC Notice: The information in this document is subject to change without notice. 6 of 7 P1707A February 2007 rev 1.2 PulseCore Semiconductor Corporation 1715 S. Bascom Ave Suite 200 Campbell, CA 95008 Tel: 408-879-9077 Fax: 408-879-9018 www.pulsecoresemi.com Copyright © PulseCore Semiconductor All Rights Reserved Part Number: P1707A Document Version: v1.3 Note: This product utilizes US Patent # 6,646,463 Impedance Emulator Patent issued to PulseCore Semiconductor, dated 11-11-2003 © Copyright 2007 PulseCore Semiconductor Corporation. All rights reserved. Our logo and name are trademarks or registered trademarks of PulseCore Semiconductor. All other brand and product names may be the trademarks of their respective companies. PulseCore reserves the right to make changes to this document and its products at any time without notice. PulseCore assumes no responsibility for any errors that may appear in this document. The data contained herein represents PulseCore’s best data and/or estimates at the time of issuance. PulseCore reserves the right to change or correct this data at any time, without notice. If the product described herein is under development, significant changes to these specifications are possible. The information in this product data sheet is intended to be general descriptive information for potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. PulseCore does not assume any responsibility or liability arising out of the application or use of any product described herein, and disclaims any express or implied warranties related to the sale and/or use of PulseCore products including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual property rights, except as express agreed to in PulseCore’s Terms and Conditions of Sale (which are available from PulseCore). All sales of PulseCore products are made exclusively according to PulseCore’s Terms and Conditions of Sale. The purchase of products from PulseCore does not convey a license under any patent rights, copyrights; mask works rights, trademarks, or any other intellectual property rights of PulseCore or third parties. PulseCore does not authorize its products for use as critical components in life-supporting systems where a malfunction or failure may reasonably be expected to result in significant injury to the user, and the inclusion of PulseCore products in such life-supporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify PulseCore against all claims arising from such use. Notebook LCD Panel EMI Reduction IC Notice: The information in this document is subject to change without notice. 7 of 7