SF161S THRU SF167S GLASS PASSIVATED SUPER FAST RECTIFIER VOLTAGE RANGE 50 to 600 Volts CURRENT 16 Amperes FEATURES * Low switching noise * Low forward voltage drop * Low thermal resistance * High current capability * Super fast switching speed * High reliability * Good for switching mode circuit .049 (1.25 REF.) D2-PAK .049 (1.25) .083 (2.10) .098 (2.50) .012 (0.30) .198 (5.03) .412 (10.46) Single phase, half wave, 60 Hz, resistive or inductive load. .053 (1.35) .020 (0.50) .202 (5.13) Ratings at 25 o C ambient temperature unless otherwise specified. .173 (4.40) .053 (1.35) .069 (1.75) .055 (1.40) .047 (1.20) .036 (0.91) .028 (0.71) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS .189 (4.80) .576 (14.64) PIN2 .110 (2.80) .126 (3.20) PIN1 .624 (15.84) .346 (8.8) * Case: D2-PAK molded plastic * Epoxy: Device has UL flammability classification 94V-O * Lead: MIL-STD-202E method 208C guaranteed * Mounting position: Any * Weight: 1.35 grams .323 (8.2) MECHANICAL DATA PIN 1 .388 (9.86) For capacitive load, derate current by 20%. PIN 2 HEATSINK Dimensions in inches and (millimeters) MAXIMUM RATINGS (@ TA=25 OC unless otherwise noted) SYMBOL SF161S SF162S SF163S SF164S SF165S SF166S SF167S UNITS Maximum Recurrent Peak Reverse Voltage RATINGS VRRM 50 100 150 200 300 400 600 Volts Maximum RMS Voltage VRMS 35 70 105 140 210 280 420 Volts VDC 50 100 150 200 300 400 600 Volts Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T C = 100 o C Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 4) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range IO 16.0 Amps I FSM 300 Amps R q JA 16 R q JC 1.2 CJ 400 T J, T STG -55 to + 150 0 C/ W pF 0 C ELECTRICAL CHARACTERISTICS (@TA=25 C unless otherwise noted) O CHARACTERISTICS Maximum Instantaneous Forward Voltage at 16.0A DC Maximum DC Reverse Current at Rated DC Blocking Voltage @T A = 25 o C @T A = 100 o C Maximum Reverse Recovery Time (Note 1) SYMBOL VF SF161S SF162S SF163S trr SF165S SF166S 1.35 10 IR NOTES : 1. Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A 2. Measured at 1 MHz and applied reverse voltage of 4.0 volts. 3. Suffix "R" for Reverse Polarity. 4. Typical Thermal Resistance : Heat-sink mounted. 5. "Fully ROHS complaint", "100% Sn plating (Pb-free)" SF164S 1.0 UNITS 1.70 Volts mAmps 500 35 SF167S 50 nSec 2007-3 Single Phase Half Wave 60 Hz Inductive or Resistive Load 4 0 0 50 100 150 CT, JUNCTION CAPACITANCE, (pF) TA = 25 OC 1.0 20 40 60 66 S 0.6 1000 TA = 100 OC 80 0.8 1.0 1.2 1.4 1.6 1.8 2.0 100 120 FIG.2 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 T J = 25 OC 10 0.1 0.2 140 0.4 1.0 PERCENT RATED PEAK REVERSE VOLTAGE, (%) 2 8.3mS Single Half Sine-Wave JEDEC Method 250 200 150 100 50 1 2 10 20 40 100 FIG.4 TYPICAL JUNCTION CAPACITANCE 300 0 4 REVERSE VOLTAGE, (V) FIG.3 TYPICAL REVERSE CHARACTERISTICS PEAK FORWARD SURGE CURRENT, (A) INSTANTANEOUS REVERSE CURRENT, (mA) FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE 0 7S 2 1.0 INSTANTANEOUS FORWARD VOLTAGE, (V) 10 0.1 16 T A = 25 OC Pulse Width = 300mS 1% Duty Cycle O 100 ~S 4 CASE TEMPERATURE, ( C) 1000 F1 S 10 16 S~ 12 5S SF 164 14 SF 8 20 SF 12 30 161 16 50 SF 20 INSTANTANEOUS FORWARD CURRENT, (A) AVERAGE FORWARD CURRENT, (A) RATING AND CHARACTERISTICS CURVES ( SF161S THRU SF167S ) 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.