SF161 THRU SF164 GLASS PASSIVATED SUPER FAST RECTIFIER VOLTAGE RANGE 50 to 200 Volts CURRENT 16 Ampere FEATURES * * * * * * * Low switching noise Low forward voltage drop Low thermal resistance High current capability Super fast switching speed High reliability Good for switching mode circuit TO-220A MECHANICAL DATA * * * * * .413 ( 10.5) .108 ( 2.75) Case: TO-220A molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 2.24 grams .374 ( 9.5) .187 ( 4.7) .153 ( 3.9) .148 ( 3.8) .146 ( 3.7) .053 ( 1.3) .047 ( 1.2) .270 ( 6.9) .230 ( 5.8) .610 ( 15.5) .583 ( 14.8) .04MAX. ( 1.0) 1 PIN 2 .157 ( 4.0) .583 ( 14.8) .051 ( 1.3) .531 ( 13.5) .035 (0.9) .028 ( 0.7) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. .020 ( 0.5) .102 ( 2.6) Single phase, half wave, 60 Hz, resistive or inductive load. .012 ( 0.3) .091 ( 2.3) For capacitive load, derate current by 20%. .126 (3.2) PIN 1 HEATSINK PIN 2 Dimensions in inches and (millimeters) MAXIMUM RATINGS (@ TA=25 OC unless otherwise noted) SYMBOL SF161 SF162 SF163 SF164 UNITS Maximum Recurrent Peak Reverse Voltage RATINGS VRRM 50 100 150 200 Volts Maximum RMS Voltage VRMS 35 70 105 140 Volts VDC 50 100 150 200 Volts Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T C = 100 o C Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 4) IO 16.0 Amps I FSM 250 Amps R q JA 16 R q JC 1.2 CJ Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range 0 pF 175 T J, T STG C/ W 0 -55 to + 150 C ELECTRICAL CHARACTERISTICS (@TA=25 C unless otherwise noted) O CHARACTERISTICS Maximum Instantaneous Forward Voltage at 16.0A DC Maximum DC Reverse Current at Rated DC Blocking Voltage @T A = 25 o C @T A = 100 o C Maximum Reverse Recovery Time (Note 1) SYMBOL SF161 SF162 VF IR trr NOTES : 1. Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A 2. Measured at 1 MHz and applied reverse voltage of 4.0 volts. 3. Suffix "R" for Reverse Polarity. 4. Typical Thermal Resistance from junction to ambient and from junction to case on heat-sink mounted. 5. "Fully ROHS complaint", "100% Sn plating (Pb-free)" SF163 0.975 10 500 35 SF164 UNITS Volts mAmps nSec 2006-11 RATING AND CHARACTERISTICS CURVES ( SF161 THRU SF164 ) INSTANTANEOUS FORWARD CURRENT, (A) AVERAGE FORWARD CURRENT, (A) 20 16 12 8 Single Phase Half Wave 60 Hz Inductive or Resistive Load 4 0 0 50 100 150 50 30 20 14 12 10 4 TA = 25 OC Pulse Width = 300mS 1% Duty Cycle 2 1.0 0.6 O 1000 CT, JUNCTION CAPACITANCE, (pF) 1000 TA = 100 OC 100 10 TA = 25 OC 1.0 0.1 0 20 40 60 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE 80 100 120 FIG.2 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 TJ = 25 OC 10 0.1 0.2 140 0.4 1.0 PERCENT RATED PEAK REVERSE VOLTAGE, (%) 2 8.3mS Single Half Sine-Wave JEDEC Method 250 200 150 100 50 1 2 10 20 40 100 FIG.4 TYPICAL JUNCTION CAPACITANCE 300 0 4 REVERSE VOLTAGE, (V) FIG.3 TYPICAL REVERSE CHARACTERISTICS PEAK FORWARD SURGE CURRENT, (A) INSTANTANEOUS REVERSE CURRENT, (mA) CASE TEMPERATURE, ( C) 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.