SF301C THRU SF307C GLASS PASSIVATED SUPER FAST RECTIFIER VOLTAGE RANGE 50 to 600 Volts CURRENT 30 Ampere s FEATURES * Low switching noise * Low forward voltage drop * Low thermal resistance * High current capability * Super fast switching speed * High -reliability * Good for switching mode circuit TO-247 * * * * * .645 (16.0 ) .625 (15.9 ) .085 (2.16 ) .075 (1.90 ) .245 (6.2 ) .225 (5.7 ) MECHANICAL DATA Case: TO-247 molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 6.10 g rams .093 (2.30 ) .076 (1.97 ) .840 (21.3 ) .820 (20.8 ) 1 2 .080 (2.10 ) .075 (1.90 ) 3 .095 (2.4 ) .085 (2.1 ) .160 (4.1 ) .140 (3.5 ) .127 (3.22 ) .117 (2.97 ) .030 (.76 ) .020 (.51 ) .795 (20.2 ) .775 (19.7 ) MAXIMUM RA TINGS AND ELECTRICAL CHARACTERISTICS .203 (5.16 ) .193 (4.90 ) .135 (3.4 ) .115 (2.9 ) Ratings at 25o C ambient temperature. .225 (5.7 ) .205 (5.2 ) .048 (1.22 ) .044 (1.12 ) PIN 1 PIN 2 HEATSINK PIN 3 Dimensions in inches and (millimeters) MAXIMUM RATINGS (At TA = 25oC unless otherwise noted) RATINGS SYMBOL SF301C SF302C SF306C SF307C UNITS SF303C SF304C SF305C Maximum Recurrent Peak Reverse Voltage VRRM 50 100 150 200 300 400 600 Maximum RMS Voltage VRMS 35 70 105 140 210 280 420 Volts VDC 50 100 150 200 300 400 600 Volts Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at TC = 100oC Volts IO 30.0 Amps Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) I FSM 300 Amps Typical Thermal Resistance RθJC Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range 3 CJ 0 120 TJ, T STG C/ W pF 100 -55 to + 150 0 C ELECTRICAL CHARACTERISTICS(At TA = 25 oC unless otherwise noted) CHARACTERISTICS SYMBOL Maximum Instantaneous Forward Voltage at 15.0A DC @TC = 25oC Maximum DC Reverse Current at Rated DC Blocking Voltage @TC = 100oC Maximum Reverse Recovery Time (Note 1) VF SF301C SF302C NOTES : 1. Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A 2. Measured at 1 MHz and applied reverse voltage of 4.0 volts. 3. Suffix “A” =Common Anode. 4. “Fully ROHS compliant”, “100% Sn plating (Pb-free)”. SF304C SF305C SF306C 1.35 10 IR trr SF303C 1.0 UNITS 1.70 Volts uAmps 500 35 SF307C 50 nSec 2005-4 REV:A RATING AND CHARACTERISTIC CURVES ( SF301C THRU SF307C ) FIG. 2 - TYPICAL REVERSE CHARACTERISTICS 1000 30 24 12 Single Phase Half Wave 60Hz Inductive or Resistive Load 6.0 0 0 50 100 CASE TEMPERATURE, ( 150 ) FIG. 3 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 300 8.3ms Single Half Sine-Wave (JEDED Method) 250 INSTANTANEOUS REVERSE CURRENT, (uA) PEAK FORWARD SURGE CURRENT, (A) AVERAGE FORWARD CURRENT, (A) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE 36 200 TC = 100 100 10 TC = 25 1.0 0.1 150 0 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) 100 50 0 1 2 5 10 20 50 NUMBER OF CYCLES AT 60Hz 100 FIG. 5 - TYPICAL JUNCTION CAPACITANCE FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10 4 ~S F3 0 20 4C 40 30 SF 5C 06 F3 ~S JUNCTION CAPACITANCE, (pF) 80 SF 30 1C INSTANTANEOUS FORWARD CURRENT, (A) 20 C 30 SF 7C 1.0 .4 .1 .4 TJ = 25 Pulse Width=300us 1% Duty Cycle .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, (V) 175 150 125 SF 30 100 SF 30 50 TJ = 25 5C ~S F3 0 1C ~S F3 0 4C 7C 25 0 .1 .5 1.0 2 5 10 20 50 100 200 REVERSE VOLTAGE, ( V ) DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.