SILIKRON SSF8521

SSF8521
DESCRIPTION
The SSF8521 uses advanced trench technology to
provide excellent RDS(ON) and low gate charge . A
Schottky diode is provided to facilitate the
implementation of a bidirectional blocking switch,
or for DC-DC conversion applications.
Schematic diagram
GENERAL FEATURES
● MOSFET
VDS = -20V,ID = -4.4A
RDS(ON) < 170mΩ @ VGS=-1.8V
RDS(ON) < 110mΩ @ VGS=-2.5V
RDS(ON) < 80mΩ @ VGS=-4.5V
SCHOTTKY
VR = 20V, IF = 4.1A, VF<0.575V @ 1.0A
● High Power and current handing capability
● Lead free product is acquired
● Surface Mount Package
Marking and pin Assignment
Application
●DC-DC conversion applications
●Load switch
●Power management
DFN3X2-8L Bottom View
PACKAGE MARKING AND ORDERING INFORMATION
Device Marking
Device
Device Package
Reel Size
Tape width
Quantity
8521
SSF8521
DFN3X2-8L
-
-
-
ABSOLUTE MAXIMUM RATINGS(TA=25℃unless otherwise noted)
Parameter
Symbol
MOSFET
Drain-Source Voltage
VDS
-20
V
Gate-Source Voltage
VGS
±8
V
ID
-4.4
A
IDM
-13
A
Drain Current-Continuous@ Current-Pulsed (Note 1)
Schottky
Unit
Schottky reverse voltage
VR
20
V
Continuous Forward Current
IF
4.1
A
Maximum Power Dissipation
PD
2.1
TJ,TSTG
-55 To 150
Operating Junction and Storage Temperature Range
W
-55 To 150
℃
THERMAL CHARACTERISTICS
©Silikron Semiconductor CO.,LTD
2008.12.1
Version : 1.1
page 1 of 5
A Good-Ark Company
SSF8521
MOSFET
Thermal Resistance, Junction-to-Ambient (Note 2)
RθJA
100
ELECTRICAL CHARACTERISTICS (TA=25℃unless otherwise noted)
Parameter
Symbol
Condition
℃/W
Min
Typ
Max
Unit
OFF CHARACTERISTICS
Drain-Source Breakdown Voltage
BVDSS
VGS=0V ID=-250μA
-20
V
Zero Gate Voltage Drain Current
IDSS
VDS=-16V,VGS=0V
-1
μA
Gate-Body Leakage Current
IGSS
VGS=±8V,VDS=0V
±100
nA
VGS(th)
VDS=VGS,ID=-250μA
-1.2
V
ON CHARACTERISTICS (Note 3)
Gate Threshold Voltage
Static Drain-Source On-Resistance
RDS(ON)
Forward Transconductance
gFS
-0.45
VGS=-4.5V, ID=-3.2A
64
80
VGS=-2.5V, ID=-2.2A
85
110
VGS=-1.8V, ID=-1.0A
120
170
VDS=-10V,ID=-2.9A
8
S
680
PF
100
PF
mΩ
DYNAMIC CHARACTERISTICS (Note4)
Input Capacitance
Clss
Output Capacitance
Coss
Reverse Transfer Capacitance
Crss
70
PF
Turn-on Delay Time
td(on)
5.8
nS
Turn-on Rise Time
tr
11.7
nS
16
nS
VDS=-10V,VGS=0V,
F=1.0MHz
SWITCHING CHARACTERISTICS (Note 4)
Turn-Off Delay Time
td(off)
VDD=-10V,ID=-3.2A
VGS=-4.5V,RGEN=2.4Ω
Turn-Off Fall Time
tf
12.4
nS
Total Gate Charge
Qg
7.4
nC
Gate-Source Charge
Qgs
1.4
nC
Gate-Drain Charge
Qgd
2.5
nC
VDS=-10V,ID=-3.2A,VGS=-4.5V
DRAIN-SOURCE DIODE CHARACTERISTICS
Diode Forward Voltage (Note 3)
VSD
VGS=0V,IS=-2.5A
-0.8
Reverse Recovery Time
Trr
13.5
nS
Reverse Recovery Charge
Qrr
VGS = 0 V, IS = −1.0 A ,
dIS/dt = 100 A/us
6.5
nC
©Silikron Semiconductor CO.,LTD
2008.12.1
Version : 1.1
-1.2
V
page 2 of 5
A Good-Ark Company
SSF8521
SCHOTTKY DIODE PARAMETERS
Forward Voltage Drop
VF
IF=1.0A
Maximum reverse leakage current
Irm
VR=20V
0.51
0.575
V
5
uA
NOTES:
1. Repetitive Rating: Pulse width limited by maximum junction temperature.
2. Surface Mounted on FR4 Board, t ≤ 10 sec.
3. Pulse Test: Pulse Width ≤ 300μs, Duty Cycle ≤ 2%.
4. Guaranteed by design, not subject to production testing.
TYPICAL ELECTRICAL AND THERMAL CHARACTERISTICS
ton
tr
Vdd
td(on)
Vin
Vgs
Rgen
td(off)
Rl
D
Vout
toff
tf
90%
VOUT
90%
INVERTED
10%
10%
G
90%
VIN
S
50%
50%
10%
PULSE WIDTH
Figure 2:Switching Waveforms
ZθJA Normalized Transient
Thermal Resistance
Figure1:Switching Test Circuit
Square Wave Pluse Duration(sec)
Figure 3: Normalized Maximum Transient Thermal Impedanc
©Silikron Semiconductor CO.,LTD
2008.12.1
Version : 1.1
page 3 of 5
A Good-Ark Company
SSF8521
DFN3X2-8L PACKAGE INFORMATION
Dimensions in Millimeters (UNIT:mm)
COMMON DIMENSIONS(MM)
PKG.
W:VERY VERY THIN
REF.
MIN.
NOM.
MAX.
A
0.70
0.75
0.80
A1
0.00
—
0.05
A3
0.2 REF.
D
2.95
3.00
3.05
E
1.95
2.00
2.05
b
0.25
0.30
0.35
L
0.28
0.35
0.43
D2
0.77
0.92
1.02
E2
0.20
0.30
0.40
e
0.65 BCS.
NOTES:
1. All dimensions are in millimeters.
2. Tolerance ±0.10mm (4 mil) unless otherwise specified
3. Package body sizes exclude mold flash and gate burrs. Mold flash at the non-lead sides should be less than 5 mils.
4. Dimension L is measured in gauge plane.
5. Controlling dimension is millimeter, converted inch dimensions are not necessarily exac
©Silikron Semiconductor CO.,LTD
2008.12.1
Version : 1.1
page 4 of 5
A Good-Ark Company
SSF8521
ATTENTION:
■
■
■
■
■
■
■
■
■
Any and all Silikron products described or contained herein do not have specifications that can handle applications that require
extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can
be reasonably expected to result in serious physical and/or material damage. Consult with your Silikron
representative nearest you before using any Silikron products described or contained herein in such applications.
Silikron assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in
products specifications of any and all Silikron products described or contained herein.
Specifications of any and all Silikron products described or contained herein stipulate the performance, characteristics, and
functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and
functions of the described products as mounted in the customer’s products or equipment. To verify symptoms and states that
cannot be evaluated in an independent device, the customer should always evaluate and test devices
mounted in the customer’s products or equipment.
Silikron Semiconductor CO.,LTD. strives to supply high-quality high-reliability products. However, any and all semiconductor
products fail with some probability. It is possible that these probabilistic failures could give rise to
accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to
other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such
measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and
structural design.
In the event that any or all Silikron products(including technical data, services) described or contained herein are controlled under
any of applicable local export control laws and regulations, such products must not be exported without obtaining the export
license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including
photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of
Silikron Semiconductor CO.,LTD.
Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume
production. Silikron believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use
or any infringements of intellectual property rights or other rights of third parties.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the Silikron product
that you intend to use.
This catalog provides information as of Dec, 2008. Specifications and information herein are subject to change without notice.
©Silikron Semiconductor CO.,LTD
2008.12.1
Version : 1.1
page 5 of 5
A Good-Ark Company