SCH5027E Super I/O with Temperature Sensing, Quiet Auto Fan and Glue Logic with PECI PRODUCT FEATURES General Features — — — — — — — — — — — Data Brief 3.3 Volt Operation (SIO Block is 5 Volt Tolerant) LPC Interface Programmable Wake-up Event Interface PC99, PC2001 Compliant ACPI 2.0 Compliant Multiplexed Command, Address and Data Bus Serial IRQ Interface Compatible with Serialized IRQ Support for PCI Systems PME Interface ISA Plug-and-Play Compatible Register Set 25 General Purpose Input/Output Pins System Management Interrupt — — — — SMSC SCH5027E 8042 Software Compatible 8 Bit Microcomputer 2k Bytes of Program ROM 256 Bytes of Data RAM Four Open Drain Outputs Dedicated for Keyboard/Mouse Interface Asynchronous Access to Two Data Registers and One Status Register Supports Interrupt and Polling Access 8 Bit Counter Timer Port 92 Support Fast Gate A20 and KRESET Outputs Motherboard GLUE Logic — IDE Reset Output — (4) Buffered PCI Reset Outputs with software controlled reset capability - default transparent — Front Panel Reset Debouncing and Power Good Signal Generation — Power Supply Turn On Circuitry with Support for power button on PS/2 Keyboard — Resume Reset Signal Generation — SMBus Isolation Circuitry (2 sets external and 1 set internal for Hardware Monitoring Block) — SMBus 2.0 compliant interface for Hardware Monitoring — LED Control (2) — Two Full Function Serial Ports — High Speed NS16C550A Compatible UARTs with Send/Receive 16-Byte FIFOs — Supports 230k and 460k Baud — Programmable Baud Rate Generator — Modem Control Circuitry — 480 Address and 15 IRQ Options Keyboard Controller — Enhanced Digital Data Separator Serial Ports Multi-Mode™ Parallel Port with ChiProtect™ — — — — — — 2 Mbps, 1 Mbps, 500 Kbps, 300 Kbps, 250 Kbps Data Rates — Programmable Precompensation Modes Multiprotocol Infrared Interface IrDA 1.0 Compliant SHARP ASK IR 480 Addresses, Up to 15 IRQ — Standard Mode IBM PC/XT®, PC/AT®, and PS/2™ Compatible Bi-directional Parallel Port — Enhanced Parallel Port (EPP) Compatible - EPP 1.7 and EPP 1.9 (IEEE 1284 Compliant) — IEEE 1284 Compliant Enhanced Capabilities Port (ECP) — ChiProtect Circuitry for Protection — 960 Address, Up to 15 IRQ and Three DMA Options AC Power Failure Recovery Watchdog Timer 2.88MB Super I/O Floppy Disk Controller — Licensed CMOS 765B Floppy Disk Controller — Software and Register Compatible with SMSC's Proprietary 82077AA Compatible Core — Supports One Floppy Drive — Configurable Open Drain/Push-Pull Output Drivers — Supports Vertical Recording Format — 16-Byte Data FIFO — 100% IBM® Compatibility — Detects All Overrun and Underrun Conditions — Sophisticated Power Control Circuitry (PCC) Including Multiple Powerdown Modes for Reduced Power Consumption — DMA Enable Logic — Data Rate and Drive Control Registers — 480 Address, Up to Eight IRQ and Three DMA Options — Support 3 Mode FDD — — — — PECI Interface — Supports PECI REQUEST# and PECI AVAILABLE signalling Infrared Port Fan Control — — — — 5 PWM (Pulse width Modulation) Outputs Low frequency and high frequency PWM support 6 Fan Tachometer Inputs Programmable automatic fan control based on temperature — Interrupt Pin for out-of-limit Fantach Events — Fantach events generate PME’s PRODUCT PREVIEW Revision 0.2 (02-11-09) Super I/O with Temperature Sensing, Quiet Auto Fan and Glue Logic with PECI Temperature Monitor — — — — — — — Monitoring of Two Remote Thermal Diodes Processor temperature monitoring by PECI Internal Ambient Temperature Measurement Limit Comparison of all Monitored Values Interrupt Pin for out-of-limit Temperature Indication Thermal events generate PME’s Configurable offset for internal or external temperature channels. Voltage Monitor — — — — Monitor Power supplies (2 at 1.125V, one at 5V, one each for Vccp, Vbat, VTR, and VCC) Limit Comparison of all Monitored Values Interrupt Pin for out-of-limit Voltage Indication Voltage events generate PME’s Security Features 3 VID (Voltage Identification) Inputs Phoenix Keyboard BIOS ROM 128 Pin QFP, Lead-Free RoHS Compliant Package — Security Key Register (32 byte) for Device Authentication ORDER NUMBER: SCH5027E-NW FOR 128 PIN, QFN LEAD-FREE ROHS COMPLIANT PACKAGE 80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000, FAX (631) 273-3123 Copyright © 2009 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Revision 0.2 (02-11-09) 2 PRODUCT PREVIEW SMSC SCH5027E Super I/O with Temperature Sensing, Quiet Auto Fan and Glue Logic with PECI General Description The SCH5027E is a 3.3V (Super I/O Block is 5V tolerant) PC99/PC2001 compliant Super I/O controller with an LPC interface. SCH5027E also includes Hardware Monitoring capabilities, enhanced Security features, Power Control logic and Motherboard Glue logic. The SCH5027E's hardware monitoring capability includes temperature, voltage and fan speed monitoring. It has the ability to alert the system to out-of-limit conditions and automatically control the speeds of multiple fans. There are four analog inputs for monitoring external voltages, two at 1.125V, one at 5V and one at 2.25V for Vccp (core processor voltage). There is also internal monitoring of the SIO's VCC, VTR, and Vbat power supplies. The SCH5027E is capable of monitoring two external diodes, one internal ambient temperature sensor or retrieving temperatures from external processors that implement the PECI interface. The PECI implementation in the SCH5027E includes support for the PECI REQUEST# and PECI AVAILABLE signals that are used to wake processors from the C3/C4sleep states. There are three pulse width modulation (PWM) outputs with high frequency support that may be controlled by the auto fan block, as well as four fan tachometer inputs. There are two additional software controlled PWM inputs with associated tachometer inputs that may be used to monitor fans. The nHWM_INT pin is implemented to indicate out-of-limit temperature, voltage, and FANTACH conditions. The hardware monitoring block of the SCH5027E is accessible via the System Management Bus (SMBus). The same interrupt event reported on the nHWM_INT pin also creates PME wakeup events and speaker alarm annunciation. The SCH5027E also allows for a two or three piece linear fan function. The Motherboard Glue logic includes various power management and system logic including generation of nRSMRST, SMBus buffers, and buffered PCI reset outputs. The SCH5027E incorporates complete legacy Super I/O functionality including an 8042 based keyboard and mouse controller, an IEEE 1284, EPP, and ECP compatible parallel port, one serial port that is 16C550A UART compatible, one IrDA 1.0 infrared ports, and a floppy disk controller with SMSC's true CMOS 765B core and enhanced digital data separator, The true CMOS 765B core provides 100% compatibility with IBM PC/XT and PC/AT architectures and is software and register compatible with SMSC's proprietary 82077AA core. System related functionality, which offers flexibility to the system designer, General Purpose I/O control functions, control of two LED's, and fan control using fan tachometer inputs and pulse width modulator (PWM) outputs. The SCH5027E is ACPI 1.0/2.0 compatible and therefore supports multiple low power-down modes. It incorporates sophisticated power control circuitry (PCC), which includes support for keyboard and mouse wake-up events. The SCH5027E supports the ISA Plug-and-Play Standard register set (Version 1.0a). The I/O Address, DMA Channel and hardware IRQ of each logical device in the SCH5027E may be reprogrammed through the internal configuration registers. There are up to 480 (960 - Parallel Port) I/O address location options, a Serialized IRQ interface, and Three DMA channels. SMSC SCH5027E 3 PRODUCT PREVIEW Revision 0.2 (02-11-09) Super I/O with Temperature Sensing, Quiet Auto Fan and Glue Logic with PECI CLK32 CLOCKI WDT* WDT CLOCK GEN SER_IRQ PCI_CLK SERIAL IRQ LAD[3:0] LPC Bus Interface LFrame# Internal Bus (Data, Address, and Control lines) PCI_RESET# High-Speed 16550A UART PORT 2 S M B u s SDA SCLK SDA1 SCLK1 SDA2 SCLK2 SMbus Isolation Switch PCI_RESET# 96 Mhz PCI Reset Outputs 14.318Mhz HWN_INT SLP_S5# SLP_S3# nRDATA, nWDATA Vbat nDIR, nSTEP nDSKCHG, nDS0, VTR DRVDEN0*, nWRTPRT SMSC Proprietary 82077 Compatible Floppydisk Controller with Digital Data Separator & Write Precompensation PD[7,0] BUSY, SLCT, PE, nERROR, nACK nSTROBE, nINIT, nSLCTIN, nALF TXD1*, RXD1 nCTS1, nRTS1* nDSR1, nDTR1 nDCD1, nRI1 TXD2 (IRTX)*, RXD2 (IRRX)* CTS2*, RTS2 * DSR2*, DTR2* DCD2*, RI2* 32 byte Security Key Register VCC nWGATE, nHDSEL General Purpose I/O Keyboard/Mouse 8042 controller Power Control and Recovery Hardware Monitor Intruder Detection nHWM_INT VREF PECI_REQUEST#* PECI READY VID3/PWMA VID4/PWMB VID5 / FANTACH3 V1_IN V2_IN VCCP_IN +2.5VTR_IN Remote1Remote1+ Remote2Remote2+ PWM1/xTest Out PWM2 PWM3/ ADDR_EN# FANTACH1 FANTACH2 FANTACH4/ ADDR_SEL PWMA*, PWMB* FANTACHA* FANTACHB* nMTR0, nTRK0, InNDEX Multi-Mode Parallel Port with ChiProtectTM/ FDC MUX (see LPC47B27x) Power Mgmt GP1[0:4]*, GP21*,GP22* GP27*, GP32*,GP33* GP36*, GP37* , GP4[0,2,3]* GP5[0:1]*, GP6[0:1]* LEDs High-Speed 16550A UART PORT 1 LDRQ# IO_PME_S3* IO_PME_S5* IO_SMI* LED2* LED1* Block Diagram nIDE_RSTDRV* nPCIRST_OUT[1:4]* MCLK*, MDAT* A20M* nKBDRST* KCLK*, KDAT* nFPRST, PB_IN# PWRGD_PS SLP_S3#, SLP_S5# ` PWRGD_CPU , PWRGD_3V SLP_S3DEL# PS_ON# nRSMRST nINTRD_IN Note 1: This diagram does not show power and ground connections. Note 2: Signal names followed by an asterisk (*) are located on multifunction pins. This diagram is designed to show the various functions available on the chip and should not be used as a pin layout . Figure 1 SCH5027E Block Diagram Revision 0.2 (02-11-09) 4 PRODUCT PREVIEW SMSC SCH5027E Super I/O with Temperature Sensing, Quiet Auto Fan and Glue Logic with PECI Chapter 2 Package Outline Figure 3 128 Pin QFP Package Outline, 14X20X2.7 Body, 3.2 mm Footprint Table 1 128 Pin QFP Package Parameters A A1 A2 D D1 E E1 H L L1 e q W R1 R2 ccc MIN ~ 0.05 2.55 23.00 19.90 17.00 13.90 0.09 0.73 ~ 0o 0.10 0.08 0.08 ~ NOMINAL ~ ~ ~ 23.20 20.00 17.20 14.00 ~ 0.88 1.60 0.50 Basic ~ ~ ~ ~ ~ MAX 3.4 0.5 3.05 23.40 20.10 17.40 14.10 0.20 1.03 ~ REMARKS Overall Package Height Standoff Body Thickness X Span X body Size Y Span Y body Size Lead Frame Thickness Lead Foot Length Lead Length Lead Pitch Lead Foot Angle Lead Width Lead Shoulder Radius Lead Foot Radius Coplanarity 7o 0.30 ~ 0.30 0.08 Notes: 1. Controlling Unit: millimeter. 2. Controlling Unit: millimeter. 3. Tolerance on the position of the leads is ± 0.04 mm maximum. 4. Package body dimensions D1 and E1 do not include the mold protrusion. 5. Maximum mold protrusion is 0.25 mm. 6. Dimension for foot length L measured at the gauge plane 0.25 mm above the seating plane. 7. Details of pin 1 identifier are optional but must be located within the zone indicated. SMSC SCH5027E 5 PRODUCT PREVIEW Revision 0.2 (02-11-09)