622 Mbps Single Mode Transceiver C-13-622(C)-T(3)-SSC4 Features • SC Duplex Single Mode Transceiver • Industry Standard 1x9 Footprint • Complies with SONET OC-12 SDH STM-4 • Single +3.3V/+5V Power Supply • OperatingTemperature Range: 0 to 70ºC and -40 to 85ºC • PECL Differential Inputs and Outputs • PECL/LVPECL Signal Detection Output [C-13-622-T(3)-SSC4] • TTL/LVTTL Signal Detection Output [C-13-622C-T(3)-SSC4] • Wave Solderable and Aqueous Washable • Uncooled laser diode with MQW structure • Complies with Telcordia (Bellcore) GR-468-CORE • SONET OC-12 Application • RoHS compliance available Absolute Maximum Rating Parameter Symbol Min. Max. Unit Vcc 0 6 V C-13-622(C)-T-SSC4 Power Supply Voltage Vcc 0 3.6 V C-13-622(C)-T3-SSC4 Output Current Iout 0 30 mA - - 260 ºC Tstg -40 85 ºC Power Supply Voltage Soldering Temperature Storage Temperature Note 10 seconds on leads only Recommended Operating Condition Parameter Symbol Min. Typ. Max. Unit Power Supply Voltage Vcc 4.75 5 5.25 V C-13-622(C)-T-SSC4 Power Supply Voltage Vcc 3.1 3.3 3.5 V C-13-622(C)-T3-SSC4 Operating Temperature (Case) Topr 0 - 70 ºC C-13-622(C)-T(3)-SSC4(D/E) Operating Temperature (Case) Topr -40 - 85 ºC C-13-622(C)-T(3)-SSC4A(B/C) - - 622 - Mbps Symbol Min Typical Max Unit Data Rate Note Transmitter Specifications Parameter Optical Notes Optical Transmit Power Po -3 - +2 dBm Output center Wavelength λp 1296 1310 1330 nm 25ºC ∆λrms - - 2.5 nm RMS(σ) ER 8.2 - - dB Output Spectrum Width Extinction Ratio Output Eye Compliant with ITU-T G.957/STM-4 Eye Mask Optical Rise Time tr - - 1.2 ns 10% to 90% Values Optical Fall Time tf - - 1.2 ns 10% to 90% Values RIN - - -120 dB/Hz TJ - - 0.55 ns Relative Intensity Noise Total Jitter LUMINENTOIC.COM Measured with 223-1 PRBS with 72 ones and 72 zeros. 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS111-Jul1106 Rev A.1 622 Mbps Single Mode Transceiver C-13-622(C)-T(3)-SSC4 Transmitter Specifications Parameter Electrical Symbol Min Typical Max Unit ICC - - 180 mA Data Input Current-Low IIL -350 - - µA Data Input Current-High IIH - - 350 µA Power Supply Current Differential Input Voltage VIH-VIL 300 - - mV Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V Data Input Voltage-High VIH-VCC -1.1 - -0.74 V Symbol Min Typical Max Unit - - - -28 dBm Pin -3 - - dBm Notes Maximum current is specified at Vcc= Maximum @ maximum temperature These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs Receiver Specifications Parameter Optical Sensitivity Maximum Input Power Notes Measured with 223-1 PRBS,BER= 10-10 Signal Detect-Asserted Pa - - -28 dBm Measured on transition: low to high Signal Detect-Deasserted Pd -40 - - dBm Measured on transition: high to low 1 - 5 dB 1100 - 1600 nm Symbol Min Typical Max Unit Note ICC - - 100 mA The current excludes the output load current Data output Voltage-Low VOL -Vcc -2 - -1.58 V Data Output Voltage-High VOH- Vcc -1.1 - -0.74 V Signal Detect Output Voltage-Low VSDL - - 0.5 V Signal Detect Output Voltage-High VSDH 2.0 - - Signal Detect Output Voltage-Low VSDL-Vcc -2.0 - -1.58 V Signal Detect Output Voltage-High VSDH- Vcc -1.1 - -0.74 V Signal Detect-Hysteresis Wavelength of Operation Receiver Specifications Parameter Electrical Power Supply Current LUMINENTOIC.COM These outputs are compatible with 10K, 10KH and 100KECL and LVPECL outputs C-13-622C-T(3)-SSC4 C-13-622-T(3)-SSC4 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS111-Jul1106 Rev A.1 622 Mbps Single Mode Transceiver C-13-622(C)-T(3)-SSC4 Connection Diagram 1. (Rx GND) 2. (Rx +) 3. (Rx-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TX-) 8. (TX+) 9. (Tx GND) NC Top View NC Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data in Transmitter Signal Ground PIN Symbol 1 RxGND 2 RD+ See recommended circuit schematic 3 RD- See recommended circuit schematic 4 SD 5 RxVcc 6 TxVcc 7 TD- See recommended circuit schematic 8 Warnings TD+ See recommended circuit schematic 9 LUMINENTOIC.COM Notes Directly connect this pin to the receiver ground plane Active high on this indicates a received optical signal +3.3V/5V dc power for the receiver section +3.3V/5V dc power for the transmitter section TxGND Directly connect this pin to the transmitter ground plane 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS111-Jul1106 Rev A.1 622 Mbps Single Mode Transceiver C-13-622(C)-T(3)-SSC4 Recommended Circuit Schematic C-13-622-T(3)-SSC4 Tx Vcc C5 Rx Vcc 9 7 8 6 5 4 3 2 1 R3 R1 R9 R5 C6 R7 TD + RD + TD - RD - Tx Vcc SD Rx Vcc R4 R2 Notes +3.3V: R1=R3=R5=R7=R9=130 R2=R4=R6=R8=R10=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H No internal connection R10 No internal connection Transceiver Top view R6 R8 L1 Notes +5V: R1=R3=R5=R7=R9=82 R2=R4=R6=R8=R10=130 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H C1 C3 Vcc Rx Vcc L2 Tx Vcc C2 C4 C-13-622C-T(3)-SSC4 Tx Vcc C5 Rx Vcc 9 R1 7 8 6 5 4 3 2 1 R5 R3 C6 R7 TD + RD + TD - RD - Tx Vcc SD Rx Vcc R2 R4 Notes +3.3V: R1=R3=R5=R7=130 R2=R4=R6=R8=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H No internal connection Transceiver Top view Notes +5V: R1=R3=R5=R7=82 R2=R4=R6=R8=130 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H R6 No internal connection R8 L1 Vcc C3 C1 L2 C4 C2 Rx Vcc Tx Vcc The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS111-Jul1106 Rev A.1 622 Mbps Single Mode Transceiver C-13-622(C)-T(3)-SSC4 Package Diagram (10.4 mm SC transceiver assembly) SC Transceiver Assembly 10.4mm Blank: Black case A : Black case Top View Front View Side View Rear View Package Diagram (9.8 mm SC transceiver assembly) SC Transceiver Assembly 9.8mm Front View Top View x8 C, D: Black case B, E: Blue case Rear View Side View LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS111-Jul1106 Rev A.1 622 Mbps Single Mode Transceiver C-13-622(C)-T(3)-SSC4 Ordering Information Available Options: C-13-622-T(3)-SSC4 C-13-622C-T(3)-SSC4 C-13-622-T(3)-SSC4-G5 C-13-622C-T(3)-SSC4-G5 C-13-622-T(3)-SSC4A C-13-622C-T(3)-SSC4A C-13-622-T(3)-SSC4A-G5 C-13-622C-T(3)-SSC4A-G5 C-13-622-T(3)-SSC4B C-13-622C-T(3)-SSC4B C-13-622-T(3)-SSC4B-G5 C-13-622C-T(3)-SSC4B-G5 C-13-622-T(3)-SSC4C C-13-622C-T(3)-SSC4C C-13-622-T(3)-SSC4C-G5 C-13-622C-T(3)-SSC4C-G5 C-13-622-T(3)-SSC4D C-13-622C-T(3)-SSC4D C-13-622-T(3)-SSC4D-G5 C-13-622C-T(3)-SSC4D-G5 C-13-622-T(3)-SSC4E C-13-622C-T(3)-SSC4E C-13-622-T(3)-SSC4E-G5 C-13-622C-T(3)-SSC4E-G5 Part unmbering Definition: C - 13 - 622(C) - T(3) - S SC TxPower Temperature and Package -RoHS • Wavelength 13= 1310 nm • Communication protocol (622 Mbps) 622 = PECL/LVPEC Signal Detection Output 622C =TTL/LVTTL Signal Detection Output • +3.3V / 5V FP Transceiver T = 5V transceiver T3 = 3.3V transceiver • Single mode fiber • Connector options SC • Tx Power range 4 = -3 to +2 dBm • Temperature range and package Blank = commercial temperature(0 to 70 ºC), 10.4 mm, Black case A = industrial temperature(-40 to 85 ºC), 10.4 mm, Black case B = industrial temperature(-40 to 85 ºC), 9.8 mm, Blue case C = industrial temperature(-40 to 85 ºC), 9.8 mm, Black case D = commercial temperature(0 to 70 ºC), 9.8 mm, Black case E = commercial temperature(0 to 70 ºC), 9.8 mm, Blue case • Ordering Information Blank = RoHS non-compliant product G5 = RoHS 5/6-compliant product (lead exemption) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS111-Jul1106 Rev A.1 622 Mbps Single Mode Transceiver C-13-622(C)-T(3)-SSC4 Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS111-Jul1106 Rev A.1