SOURCE SP-48-IR1-CDA

OC-48 IR1/STM-16 S-16.1 SFP Transceiver
SP-48-IR1
Features
• Compliant with OC48/STM-16 Standards
• Single 3.3 V supply
• 15 km reach
• 15 dB min, 19.5 typical link budget
• Commerical and Reduced Industrial temperature available
• 1310nm DFB Laser
• SFP MSA SFF-8074i compliant
• GR 253/STM G.957 compliant
• Digital Diagnostic SFF-8472 compliant
• Telcordia GR-468 compliant
• RoHS 5/6 compliant (Lead Exemption)
General Operating
Parameter
Symbol
Min.
Typ.
Max.
Unit
Supply Voltage
Vcc
3.135
3.3
3.465
V
Total Current
ICC
-
-
300
mA
Power Supply Noise Rejectiona
PSR
100
-
-
mVp-p
Operating Temerature(-Cxx)
Topr
-5
-
70
ºC
Operating Temerature(-Rxx)
Topr
-20
-
85
ºC
Storage Temperature
Tstg
-40
-
85
ºC
Data Rate OC48/STM-16
DR
-
2488.32
-
Mbps
a) 20Hz to 155MHz
Transmitter Specifications, Optical
Parameter
Symbol
Min
Typical
Max
Unit
Optical Power
Pop
-5
-2.5
0
dBm
Average Launch Power of Off Tx
Poff
-
-
-30
dBm
Extinction Ratio
ER
8.2
-
-
dB
Eye Mask
SONET/SDH compliant
Optical Jitter Generation
Jgen
-
-
0.007
UI
Timeb
tr
-
-
160
ps
Optical Fall Timeb
tf
-
-
160
ps
Optical Rise
λ
1260
1310
1360
nm
Spectral Width (20dB)
∆λ
-
-
1
nm
Dispersion Penalty (15Km)c
dp
0.5
1
dB
Relative Intensity Noise
RIN
-
-
-120
dB/Hz
Reflectance Toleranced
rp
-27
-
-
dB
Mean Wavelength
b) 20%-80% values
c) Measured at BER of 1e-10, PRBS of 223-1, at eye center
d) 1dB degradation of receiver sensitivity
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS258-FEB1706
rev.A.1
OC-48 IR1/STM-16 S-16.1 SFP Transceiver
SP-48-IR1
Transmitter Specifications , Electrical
Parameter
Symbol
Min
Typical
Max
Unit
Rin
80
100
120
Ω
Vin, p-p
250
-
1200
mV
Vfault
2
-
Vcc
V
Vnormal
Vd
Vee
-
Vee + 0.5
V
TxDisable_Disable
2
-
Vcc
V
TxDisable_Enable
Ven
Vee
-
Vee + 0.8
V
Parameter
Symbol
Min
Typical
Max
Unit
Receiver Power Lowe
Rsens,low
-
-22
-20
dBm
Receiver Power Highe
Rsens,high
0
-
-
dBm
Damage Threshold for Receiver
Pin, damage
4
-
-
dBm
λ
1260
1310
1360
nm
RX_r
-
-
-27
dB
LOS Assert
-
-30
-
-
dBm
LOS De-assert
-
-
-
-20
dBm
LOS Hysteresis
-
0.5
-
-
dB
Parameter
Symbol
Min
Typical
Max
Unit
PECL Single Ended Data Output Swing
Vout,p-p
185
-
800
mV
tr
-
-
175
ps
tf
-
-
175
ps
Input Differential Impedence
PECL Single Ended data input swing
TxFault_Fault
TxFault_Normal
Receiver Specifications, Optical
Wavelengthf
Maximum Reflectance of Receiver
e) At 10-10 BER, PRBS 223-1
f) Operational over 1200-1625 nm range
Electrical Output
Data Output Rise Time
Data Output Fall Time
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS258-FEB1706
rev.A.1
OC-48 IR1/STM-16 S-16.1 SFP Transceiver
SP-48-IR1
Timing and Electrical
Parameter
Symbol
Min
Typical
Max
Unit
Tx Disable Negate time
t_on
-
Tx Disable assert time
t_off
-
-
1
ms
-
10
Time to initialize, including reset of Tx fault
t_init
µs
-
-
300
ms
Tx fault Assert time
t_fault
-
-
100
µs
Tx Disable to reset
t_reset
10
-
-
µs
t_loss_on
-
-
100
µs
t_loss_off
f_serial_clock
Rx_LOSH
2
-
100
100
-
µs
KHz
V
LOS Assert time
LOS De-assert time
Serial ID Clock Rate
RX_LOS Voltage (high)
RX_LOS Voltage (low)
RX_LOSL
-
-
0.8
V
LOS output voltage-Fault
VLOS fault
2
-
Vcc
V
VLOS normal
Vee
-
Vee + 0.5
V
MOD_DEF (0:2)-High
Vh
2
-
VI
Vee
-
Vcc
Vee + 0.5
V
MOD_DEF (0:2)-Low
LOS output voltage-Normal
V
Diagnostics
Parameter
Range
Accuracy
Unit
Calibration
Formula
Temperature(-CDx)
-5 to 70
±3
ºC
Internal
Tc(C) = Tad(16 bit signed twos complement)/256
Temperature(-RDx)
-20 to 85
±3
ºC
Internal
Tc(C) = Tad(16 bit signed twos complement)/256
Voltage
0 to Vcc
0.1
V
Internal
V(Volts) = Vad(16 bit unsigned integer)*0.1
Bias Current
0 to 120
5
mA
External
I(mA) = Islope * Iad(16 bit unsigned integer)+Ioffset
Tx Power
-5 to 0
±3dB
dBm
External
Tx_PWR(µW) = Tx_PWRslope*Tx_PWRad(16 bit unsigned integer)+Tx_
PWRoffset
Rx Power
-24 to 0
±3dB
dBm
External
Rx_PWR(µW) = A0+A1*x+A2*x^2+A3*x^3+A4*x^4
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS258-FEB1706
rev.A.1
OC-48 IR1/STM-16 S-16.1 SFP Transceiver
SP-48-IR1
EEPROM Serial ID
Name of Field
Discription of Field
SFPVendor name (ASCII)
Vendor Name
IEEE vendor OUI code for LuminentOIC Inc.
Vendor OUI
Part number in ASCII, e.g.
SP-48-IR1-CDA
Vendor PN
Address
Hex
ASCII
20
4C
L
21
55
U
22
4D
M
23
49
I
24
4E
N
25
45
E
26
4E
N
27
54
T
28
4F
O
29
49
I
30
43
C
37
00
38
06
39
B5
40
53
41
50
P
42
34
4
43
38
8
44
49
I
45
52
R
46
31
47
43
1
C
48
44
D
49
41
A
S
Pinout Definitions
Pin
Function
Notes
1
VeeT
TX GND
2
TX_FAULT
Open Collector
3
TX_DISABLE
Internally Pulled High
4
MOD_DEF2
Serial Data Input
5
MOD_DEF1
Serial Clock Input
6
MOD_DEF0
Internally Grounded
7
NC
Not Connected
8
LOS
Open Collector
9
VeeR
RX Ground
10
VeeR
RX Ground
11
VeeR
RX Ground
12
RXD-
RX Data Negative
13
RXD+
RX Data Positive
14
VeeR
RX GND
15
VCCR
RX Power
16
VCCT
TX Power
17
VeeT
TX GND
18
TXD+
TX Data Positive
19
TXD-
TX Data Negative
20
VeeT
TX GND
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS258-FEB1706
rev.A.1
OC-48 IR1/STM-16 S-16.1 SFP Transceiver
SP-48-IR1
Outline Drawing
Units in mm(inch)
Suggested Transceiver Interface
1µH
V CC
10 µF
Protocol IC
0.1 µF
1µH
VCC T
.01µF
LuminentOIC
R1
10k Ω
TX_DISABLE
TX_DISABLE
Laser Driver
TX_FAULT
TX_FAULT
SerDes
TD +
.01µF
100Ω
TD .01µF
VEE T
VCC R
10µF
Receiver Amplifier
0.1µF
RD +
.01µF
100Ω
RD .01µF
RX_LOS
RX_LOS
V CC
VEE R
R1
R1
R1
EEPROM
R1
MOD_DEF 2
MOD_DEF 1
MOD_DEF 0
R 1 = 4.7Κ to 10ΚΩ
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS258-FEB1706
rev.A.1
OC-48 IR-1/STM-16 S-16.1 SFP Transceiver
SP-48-IR1
Ordering Information
A vailable Options:
SP-48-IR1-CDA
SP-48-IR1-CNA
SP-48-IR1-RDA
SP-48-IR1-RNA
Part numbering Definition:
SP - 48 - IR1 - Temperature Diagnostic Revision
• SP = Small Form Pluggable
48 = OC48
IR1 = Intermediate reach 15km
• Operating Temperature
C = Commeracial (-5 to 70)
R = Reduced Industrial Temperature (-20 to 85)
• D = Digital Diagnostic
N = No Digital Diagnostic
• Design Revision
Warnings:
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notes:
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS258-FEB1706
rev.A.1