SOURCE SP-MR-SR1-RDA

Multi-Rate SFP Transceiver(SR1)
SP-MR-SR1
Features
• Single 3.3 V supply
• 10 dB minimum link budget
• 2 km reach
• Commercial, Reduced and Industrial temperature available
• 1310nm FP laser
• Fibre Channel 100-SM-LC-L compliant
• Fibre Channel 200-SM-LC-L compliant
• Gigabit Ethernet 802.3ah 1000BASE-LX compliant
• SFP MSA SFF-8074i compliant
• GR 253/STM G.957 compliant
• Digital Diagnostic SFF-8472 Rev.9.3 compliant
• Telcordia GR-468 compliant
• Color coded bail latch tube : Grey
• RoHS compliant
General Operating
Symbol
Min.
Typ.
Max.
Supply Voltage
Parameter
Vcc
3.135
3.3
3.465
V
Total Current
ICC
-
-
300
mA
Power Supply Noise Rejectiona
Unit
100
-
-
mVp-p
Operating Temperature (-CxA)
Top
-5
-
70
ºC
Operating Temperature (-RxA)
Top
-20
-
85
ºC
Operating Temperature (-TxA)
Top
-40
-
85
ºC
Storage Temperature
Tstg
-40
-
85
ºC
Data Rate
DR
100
-
2700
Mbps
a) 20Hz to 155MHz
Transmitter Specifications, Optical
Parameter
Symbol
Min
Typical
Max
Unit
Optical power
Pop
-10
-6
-3
dBm
Average Launch power of off Tx
Poff
-
-
-45
dBm
Extinction Ratio
ER
9
-
-
dB
Eye Mask
IEEE 802.3z, SONET/SDH compliant
Optical Jitter generation
Jgen
-
-
0.007
UI
timeb
tr
-
-
160
ps
Optical Fall timeb
tf
-
-
160
ps
nm
Optical Rise
λ
1266
1310
1360
Spectral width (RMS)
Δλ
-
-
4
nm
Relative Intensity Noise
RIN
-
-
-120
dB/Hz
Reflectance Tolerancec
rp
-24
-
-
dB
Mean Wavelength
b) 20%-80% values
c) 1 dB degradation of receiver sensitivity
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS1526-Jan2308
Rev A.2
Multi-Rate SFP Transceiver(SR1)
SP-MR-SR1
Transmitter Specifications , Electrical
Parameter
Symbol
Min
Typical
Max
Unit
Rin
80
100
120
Ω
Vin, p-p
250
-
1200
mV
Vfault
2
-
Vcc
V
Vnormal
Vd
Vee
-
Vee + 0.5
V
TxDisable_Disable
2
-
Vcc
V
TxDisable_Enable
Ven
Vee
-
Vee + 0.8
V
Parameter
Symbol
Min
Typical
Max
Unit
Receiver Power Lowd
Rsens,low
-
-22
-20
dBm
Receiver Power Highd
Rsens,high
-3
-
-
dBm
Damage Threshold for Receiver
Pin, damage
4
-
-
dBm
nm
Input Differential Impedence
PECL Single Ended data input swing
TxFault_Fault
TxFault_Normal
Receiver Specifications, Optical
Wavelengthe
λ
1260
1310
1360
RX_r
-
-
-27
dB
LOS Assert
-
-30
-
-
dBm
LOS De-assert
-
-
-
-20
dBm
LOS hysteresis
-
0.5
-
-
dB
Maximum Reflectance of Receiver
d) at 10-10 BER, PRBS 223-1 for SONET, 10-12 BER, PRBS 27-1 for Gigabit ethernet
e) Operational over 1200-1625 nm range
Electrical Output
Parameter
Symbol
Min
Typical
Max
Unit
PECL Single ended data output swing
Vout,p-p
185
-
800
mV
Data output rise time
tr
-
-
175
ps
Data output fall time
tf
-
-
175
ps
Max
Unit
ms
Timing and Electrical
Parameter
Symbol
Min
Typical
Tx Disable Negate time
t_on
-
-
5
Tx Disable assert time
t_off
-
-
10
µs
Time to initialize, including reset of Tx fault
t_init
-
-
300
ms
Tx fault Assert time
t_fault
-
-
100
µs
Tx Disable to reset
t_reset
10
-
-
µs
t_loss_on
-
-
100
µs
t_loss_off
f_serial_clock
Rx_LOSH
2
-
100
100
-
µs
KHz
V
LOS Assert time
LOS De-assert time
Serial ID Clock Rate
RX_LOS Voltage (high)
RX_LOS Voltage (low)
RX_LOSL
-
-
0.8
V
LOS output voltage-Fault
VLOS fault
2
-
Vcc
V
VLOS normal
Vee
-
Vee + 0.5
V
MOD_DEF (0:2)-High
Vh
2
-
VI
Vee
-
Vcc
Vee + 0.5
V
MOD_DEF (0:2)-Low
LOS output voltage-Normal
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
V
LUMNDS1526-Jan2308
Rev A.2
Multi-Rate SFP Transceiver(SR1)
SP-MR-SR1
Diagnostics
Parameter
Range
Accuracy
Unit
Calibration
Temperature(-CDA)
-5 to 70
±3
ºC
External
Tc(C) = Tslope*Tad(16 bit signed twos complement value) + Toffset
Formula
Temperature(-RDA)
-20 to 85
±3
ºC
External
Tc(C) = Tslope*Tad(16 bit signed twos complement value) + Toffset
Temperature(-TDA)
-40 to 85
±3
ºC
External
Tc(C) = Tslope*Tad(16 bit signed twos complement value) + Toffset
Voltage
0 to Vcc
0.1
V
External
V(Volts) = Vslope*Vad (16 bit unsigned integer) + Voffset
Bias Current
0 to 120
5
mA
External
I(mA) = Islope * Iad(16 bit unsigned integer)+Ioffset
Tx Power
-10 to -3
±3dB
dBm
External
Tx_PWR(µW) = Tx_PWRslope*Tx_PWRad(16 bit unsigned integer)+Tx_
PWRoffset
Rx Power
-20 to -3
±3dB
dBm
External
Rx_PWR(µW) = A0+A1*x+A2*x^2+A3*x^3+A4*x^4
Pinout Definitions
Pin
Function
Notes
1
VeeT
TX GND
2
TX_FAULT
Open Collector
3
TX_DISABLE
Internally Pulled High
4
MOD_DEF2
Serial Data Input
5
MOD_DEF1
Serial Clock Input
6
MOD_DEF0
Internally Grounded
7
NC
Not Connected
8
LOS
Open Collector
9
VeeR
RX Ground
10
VeeR
RX Ground
11
VeeR
RX Ground
12
RXD-
RX Data Negative
13
RXD+
RX Data Positive
14
VeeR
RX GND
15
VCCR
RX Power
16
VCCT
TX Power
17
VeeT
TX GND
18
TXD+
TX Data Positive
19
TXD-
TX Data Negative
20
VeeT
TX GND
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS1526-Jan2308
Rev A.2
Multi-Rate SFP Transceiver(SR1)
SP-MR-SR1
EEPROM Serial ID
Name of Field
Vendor Name
Vendor OUI
Vendor PN
LUMINENTOIC.COM
Discription of Field
SFPVendor name (ASCII)
IEEE vendor OUI code for LuminentOIC Inc.
Part number in ASCII, e.g.
SP-MR-SR1-CDA
Address
Hex
20
4C
L
21
55
U
22
4D
M
23
49
I
24
4E
N
25
45
E
26
4E
N
27
54
T
28
4F
O
29
49
I
30
43
C
37
00
38
06
39
B5
40
53
S
41
50
P
42
4D
M
43
52
R
44
53
S
45
52
R
46
31
1
47
43
C
48
44
49
41
D
A
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
ASCII
LUMNDS1526-Jan2308
Rev A.2
Multi-Rate SFP Transceiver(SR1)
SP-MR-SR1
Outline Drawing
Units in mm(inches)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS1526-Jan2308
Rev A.2
Multi-Rate SFP Transceiver(SR1)
SP-MR-SR1
Suggested Transceiver Interface
1�H
Vcc
10�F
1�H
0.1�F
VCCT
.01�F
Protocol IC
R1
LuminentOIC
SFP
10K�
TX_DISABLE
TX_DISABLE
TX_FAULT
TX_FAULT
TD +
SerDes
Laser Driver
.01�F
100�
TD VEET
.01�F
VCCR
10�F
0.1�F
RD +
Receiver Amplifier
.01�F
100�
RD -
RX_LOS
RX_LOS
Vcc
R
VEER
1
R1
R1
.01�F
EEPROM
R1
MOD_DEF 2
MOD_DEF 1
MOD_DEF 0
R1=4.7K to 10K�
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS1526-Jan2308
Rev A.2
Multi-Rate SFP Transceiver(SR1)
SP-MR-SR1
Ordering Information
Available Options:
SP-MR-SR1-CDA
SP-MR-SR1-RDA
SP-MR-SR1-TDA
SP-MR-SR1-CNA
SP-MR-SR1-RNA
SP-MR-SR1-TNA
Part numbering Definition:
SP - MR - SR1 - Temperature Diagnostic
Revision
• SP = Small Form Pluggable
MR = Multi Rate
SR1 = Short Reach 2 km
• Operating Temperature
C = Commercial (-5 to 70ºC)
R = Reduced Industrial (-20 to 85ºC)
T = Industrial (-40 to 85ºC)
• D = Digital Diagnostic (SFF-8472)
N = No Digital Diagnostic
• Design Revision
A = RoHS compliant
Warnings:
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notes:
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
7
LUMNDS1526-Jan2308
Rev A.2