SFP Bi-Directional Transceiver Preliminary SPL-53-MR-IR1 Features • Compatible with IEEE 802.3ah, 1000Base-BX10 • Compatible OC-48/STM-16 Standards • GR 253/ STM G.957 compliant • Single 3.3V Supply • Simplex LC Connector • Digital Diagnostic SFF-8472 Compliant • SFP MSA SFF-8074i Compliant • 13dB Minimum Power Budget • 15km Minimum Reach • Commercial temperature available (-Cxx) • Industrial temperature available (-Txx) • 1550nm DFB Laser • Telcordia GR-468 Compliant • Color code Bail Latch : Yellow • RoHS compliant (lead free soldered) General Operation Symbol Min. Typ. Max. Unit Supply Voltage Parameter Vcc 3.135 3.3 3.465 V Total Current ICC Power Supply Noise Rejection - - 300 mA 100 - - mVp-p Operating Temperature (-Cxx) Topr -5 - 70 ºC Operating Temperature (-Txx) Topr -40 - 85 ºC Storage Temperature Tstg -40 - 85 ºC Data Rate OC-48 DR - 2488.32 - Mbps Data Rate FEC DR - 2700 - Mbps Data Rate Gigabit Ethernet DR - 1250 - Mbps Data Rate FC DR DR - 1062.5 - Mbps - 2125 - Mbps Data Rate 2xFC Transmitter Specifications (Optical) Parameter Symbol Min Typical Max Unit Optical Power Pop -5 -2.5 0 dBm Optical Crosstalk XT - - -45 dB Average Launch Power (Tx:Off) Poff - - -45 dBm Extinction Ratio ER 8.2 - - dB Optical Rise Time (20% to 80% values) tr - Optical Fall Time (20% to 80% values) tf - - 160 ps Mean Wavelength λ 1480 1550 1580 nm ∆λ - - 1 nm dB Eye Mask Spectral Width (20dB) Side Mode Suppression Ratio SONET/IEEE 802.3ah Compliant - 160 SMSR 30 - - Dispersion penalty (15km)a dp - 0.5 1 ps Relative Intensity Noise RIN - - -120 dB/Hz Transmitter Reflectance - - - -12 dB Reflectance Tolerance rp -24 - - dB a) Measured at 2.7 Gb/s, BER of 10-12, PRBS of 223-1, at eye center LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS1693-Apr3007 Rev 0.1 SFP Bi-Directional Transceiver Preliminary SPL-53-MR-IR1 Transmitter Specifications (Electrical) Parameter Symbol Min Typical Rin 80 100 120 Ω Vin, p-p 250 - 1200 mV Vfault 2 - Vcc V - Vee + 0.5 V TxDisable_Disable Vnormal Vd Vee 2 - Vcc V TxDisable_Enable Ven Vee - Vee + 0.8 V Parameter Symbol Min Typical Max Unit Receiver Power Lowb - -20 -18 dBm Receiver Power Highb Rsens,low Rsens,high 0 - - dBm Damage Threshold for Receiver Pin, damage - - 0 dBm Wavelength λ 1260 - 1360 nm LOS Assert - -28 - - dBm LOS De-Assert - - - -18 dBm LOS Hysteresis - 0.5 - - dB Receiver Reflectance - - - -12 dB Input Differential Impedence PECL Single-Ended Data Input Swing TxFault_Fault TxFault_Normal Max Unit Receiver Specifications (Optical) b) Measured at 10-10 BER, 2.7 Gb/s, 223-1 PRBS, and 10-12 BER, 1250 Mb/s, 27-1 PRBS Receiver Specifications (Electrical) Parameter Symbol Min Typical Max Unit PECL Single-Ended Data Output Swing Vout,p-p 185 - 800 mV Data Output Rise Time tr - - 175 ps Data Output Fall Time tf - - 175 ps Timing and Electrical Parameter Symbol Min Typical Max Unit Tx Disable Negate Time t_on - - 1 ms Tx Disable Assert Time t_off - - 10 µs t_init - - 300 ms Tx Fault Assert Time Time to Initialize, Including Reset of Tx Fault t_fault - - 100 µs Tx Disable to Reset t_reset 10 - - µs t_loss_on - - 100 µs t_loss_off f_serial_clock Rx_LOSH 2 - 100 100 - µs KHz V LOS Assert Time LOS De-Assert Time Serial ID Clock Rate RX_LOS Voltage (High) RX_LOS Voltage (Low) RX_LOSL - - 0.8 V LOS Output Voltage-Fault VLOS fault 2 - Vcc V VLOS normal Vee - Vee + 0.5 V MOD_DEF (0:2)-High Vh 2 - V MOD_DEF (0:2)-Low VI Vee - Vcc Vee + 0.5 LOS Output Voltage-Normal LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 V LUMNDS1693-Apr3007 Rev 0.1 SFP Bi-Directional Transceiver Preliminary SPL-53-MR-IR1 Diagnostics Range Accuracy Temperature (-Cxx) -5 to 70 ±3 ºC Internal 1/256 C Temperature (-Txx) -40 to 85 ±3 ºC Internal 1/256 C Tc(C)=Tad(16 bit signed twos complement)/256 Voltage 0 to Vcc 0.1 V Internal 100 µV V(Volts)=Vad(16 bit unsigned integer)*0.1 Bias current 0 to 120 5 mA External 0.002mA TX Power -5 to 0 ±2dB dBm External 0.1 µw TX_PWR(µW)=TX_PWRslope*TX_PWRad(16 bit unsigned integer +TX_PWRoffset RX Power -18 to 0 ±2dB dBm External 0.1 µw RX_PWR(µW)=A0+A1*x+A2*x^2+A3*x^3+A4*x^4 Parameter Unit Calibration Bit value Formula Tc(C)=Tad(16 bit signed twos complement)/256 I(mA)=Islope*Iad(16 bit unsigned integer)+Ioffset Pinout Definitions Pin Function Notes 1 VeeT TX GND 2 TX_FAULT Open Collector 3 TX_DISABLE Internally Pulled High 4 MOD_DEF2 Serial Data Input 5 MOD_DEF1 Serial Clock Input 6 MOD_DEF0 Internally Grounded 7 NC Not Connected 8 LOS Open Collector 9 VeeR RX Ground 10 VeeR RX Ground 11 VeeR RX Ground 12 RXD- RX Data Negative 13 RXD+ RX Data Positive 14 VeeR RX GND 15 VCCR RX Power 16 VCCT TX Power 17 VeeT TX GND 18 TXD+ TX Data Positive 19 TXD- TX Data Negative 20 VeeT TX GND LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS1693-Apr3007 Rev 0.1 SFP Bi-Directional Transceiver Preliminary SPL-53-MR-IR1 EEPROM Serial ID Name of Field Vendor Name Vendor OUI Vendor PN LUMINENTOIC.COM Description of Field SFP Vendor name(ASCII) IEEE vendor OUI code for LuminentOIC Inc. Part number in ASCII, e.g. SPL-53-MR-IR1-CDA Address Hex ASCII 20 4C L 21 55 U 22 4D M 23 49 I 24 4E N 25 45 E 26 4E N 27 54 T 28 4F O 29 49 I 30 43 C 37 00 38 06 39 B5 40 53 S 41 50 P 42 4C L 43 35 5 44 33 3 45 4D M 46 52 R 47 49 I 48 52 R 49 31 1 50 43 C 51 44 D 52 41 A 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS1693-Apr3007 Rev 0.1 SFP Bi-Directional Transceiver Preliminary SPL-53-MR-IR1 Suggested Transceiver Interface Mechanicals Units in mm (inches) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS1693-Apr3007 Rev 0.1 SFP Bi-Directional Transceiver Preliminary SPL-53-MR-IR1 Suggested Transceiver Interface 1�H Vcc 10�F 1�H 0.1�F VCCT .01�F Protocol IC R1 LuminentOIC SFP 10K� TX_DISABLE TX_DISABLE TX_FAULT TX_FAULT TD + SerDes Laser Driver .01�F 100� TD VEET .01�F VCCR 10�F 0.1�F RD + Receiver Amplifier .01�F 100� RD - RX_LOS RX_LOS Vcc R VEER 1 R1 R1 .01�F EEPROM R1 MOD_DEF 2 MOD_DEF 1 MOD_DEF 0 R1=4.7K to 10K� LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS1693-Apr3007 Rev 0.1 SFP Bi-Directional Transceiver Preliminary SPL-53-MR-IR1 Ordering Information Available Options: SPL-53-MR-IR1-CDA SPL-53-MR-IR1-CNA SPL-53-MR-IR1-TDA SPL-53-MR-IR1-TNA Part numbering Definition: SPL - 53 - MR - IR1 - Temperature Diagnostic Revision • SPL = LC connector • 53 = Tx 1550nm/Rx 1310nm • MR = Multi Rate • IR1 = Reach 15 km • Operating Temperature C = Commercial temperature (-5 to 70ºC) T = Industrial temperature (-40 to 85ºC) • D = Digital Diagnostic (SFF-8472) N = No Diagnostic • Design Revision A = RoHS compliant (lead free soldered) Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at Luminent’s sole and absolute discretion. Luminent warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and Luminent expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. Luminent assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and Luminent makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. Luminent customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify Luminent for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that Luminent is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact Luminent to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © Luminent, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS1693-Apr3007 Rev 0.1