STATEK CXOX_13

CXOX/CXOXHG OSCILLATOR
1 MHz to 160 MHz
Ultra-Miniature, High Stability
High Shock Crystal Oscillator
DESCRIPTION
Statek’s ultra miniature and ultra low profile
CXOX/CXOXHG oscillators consist of a CMOS/TTL
compatible hybrid circuit and a state-of-the-art, miniature,
fundamental-mode crystal.
DIMENSIONS
A
FEATURES
4
High shock resistance (HG version)
CMOS and TTL compatible
3
TOP
Low power consumption
1
Full military testing available
Low acceleration sensitivity (HG version)
Optional Output Enable/Disable with Tri-State
Low EMI emission
Hermetically sealed ceramic package
Designed and manufactured in the USA
APPLICATIONS
C
2
D
B
2
TYPICAL
E
4
3
BOTTOM
1
MAXIMUM
DIM
inches
mm
inches
mm
A
0.126
3.20
0.136
3.40
B
0.099
2.50
0.107
2.70
C (SM1)
0.039
C (SM3/SM5) 0.044
1.00
1.12
0.043
0.048
1.09
1.21
D
0.040
1.00
0.041
1.10
E
0.030
0.75
0.031
0.85
Military & Aerospace
Smart munitions
PIN CONNECTIONS
Communications
1. Output Enable/Disable (E) or no connection (N)
Navigation
2. Ground
GPS
3. Output
Industrial, Computer & Communications
Miniature clock oscillator
4. VDD
SUGGESTED LAND PATTERN
Handheld instrumentation
0.141 (3.6)
PDA
Transponder/Animal migration
Medical
Test & diagnostic equipment
0.110 (2.9)
0.031 (0.8)
Handheld devices
0.039 (1.05)
0.051
(1.3)
0.039
(1.0)
inches (mm)
IS O
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
90
01
TEM
C ERT I F I C
AT
N
IO
S
10168 Rev C
YS
SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
Specifications below are examples. Specifications are subject
to change without notice. Tighter specifications available.
Please contact factory.
Supply Voltage VDD
-0.5 V to 7.0 V
Storage Temperature
-55OC to 125OC
Maximum Process Temperature 260OC for 20 seconds
Frequency Range1
Supply Voltage
1 MHz to 160 MHz
1.8 V to 5.0 V ± 10%
Calibration Tolerance2
± 100 ppm
Frequency Stability
Over Temperature3
Supply Current (Typical)
24 MHz
32 MHz
50 MHz
130 MHz
Output Load (CMOS)4
ENABLE/DISABLE OPTIONS (E/N)
± 50 ppm for Commercial
± 100 ppm for Industrial
± 100 ppm for Military
1.8 V
3.3 V
5.0 V
1.5 mA
3.0 mA
8.0 mA
2.0 mA
5.0 mA
10.0 mA
3.0 mA
6.0 mA
13.0 mA
12.0 mA 23.0 mA
39.0 mA
ENABLE/DISABLE OPTION E
FUNCTION TABLE
15 pF
Start-up Time
5 ms MAX
Rise/Fall Time
6 ns MAX
Duty Cycle
40% MIN 60% MAX
Aging, first year
5 ppm MAX
Shock, survival6
5,000 g, 0.3 ms, 1/2 sine
HG: 10,000 g, 0.3 ms, 1/2 sine`
Vibration, survival7
20 g, 10-2,000 Hz swept sine
5
Statek offers two enable/disable options: E and N. The Eversion has a Tri-State output and stops oscillating internally
when the output is put into the high Z state. The N-version
does not have PIN 1 connected internally and so has no
enable/disable capability. The following table describes the
Enable/Disable option E.
Enable (Pin 1 High*) Disable (Pin 1 Low)
Output
Frequency Output
High Z State
Oscillator
Oscillates
Stops
Current
Normal
Very Low
* When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
Operating Temp. Range -10 C to 70 C (Commerical)
-40OC to 85OC (Industrial)
-55OC to 125OC (Military)
O
O
PACKAGING OPTIONS
1.
2.
3.
4.
5.
6.
7.
Not all frequencies available at all voltages. Contact factory.
Tighter tolerances available.
Does not include calibration tolerances. Tighter tolerances available.
Higher CMOS loads and TTL loads available. Contact factory.
45/55 available upon request in most cases.
Higher shock version available. Contact factory for requirements above 10,000 g
Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also
available.
Note: All parameters are measured at ambient temperature with a 10 M1, 15 pF load.
CXOX/
CXOXHG
- Tray Pack
- 12 mm tape, 7” or 13” reels
Per EIA 481 (see Tape and Reel data sheet
#10109)
HOW TO ORDER CXOX/CXOXHG SURFACE MOUNT CRYSTAL OSCILLATORS
CXOX
HG = High
Shock.
Otherwise
leave blank
HG
4
Supply Voltage
1 = 1.8 V
2 = 2.5 V
3 = 3.0 V
4 = 3.3 V
5 = 5.0 V
S
N
“S” if special or
custom design.
Blank if Std.
Enable/Disable
Option
E or N
SM3
Terminations
Blank = SM1
= Gold Plated
(Lead Free)
SM3 = Solder Dipped
SM5 = Solder Dipped
(Lead Free)
40.0M ,
Frequency
K = kHz
M = MHz
100
/
Calibration
Tolerance
@ 250C
(in ppm)
100
/
Frequency
Stability over
Temp. Range
(in ppm)
Temp. Range:
C = -10OC to +70OC
I = -40OC to +85OC
M = -55OC to +125OC
S = Customer Specified
OR
/
/
I
/
200
Total
Frequency
Tolerance
(in ppm)
/
I
Temp. Range:
C = -10OC to +70OC
I = -40OC to +85OC
M = -55OC to +125OC
S = Customer Specified
IS O
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
90
01
TEM
C ERT I F I C
AT
N
IO
S
10168 Rev C
YS