ZETTLER AT-320240Q5FIQW

A MP I R E
SPECIFICATIONS FOR
LCD MODULE
CUSTOMER
CUSTOMER PART NO.
AMPIRE PART NO.
AT-320240Q5FIQW-T76H(V)(R)
APPROVED BY
DATE
APPROVED BY
Date : 2006/9/12
CHECKED BY
AMPIRE CO., LTD.
ORGANIZED BY
1
RECORD OF REVISION
Revision Date
Contents
Editor
2006/8/8
New Release
Lorry
2006/9/12
Modify Mechanical data
Tony
Date : 2006/9/12
AMPIRE CO., LTD.
2
1
FEATURES
(1)
Display format : 320 × 240 dot- matrix, 1/240 duty.
(2)
Construction : FSTN LCD, TAB type LCD driver, White Edge LED backlight,
Touch Panel , Touch Panel controller (TSC2046) and PCB.
(3)
Display type : FSTN ,Transflective , 6 o’clock view.
(4)
Controller : RA8835.
(5)
New Driving Method CMOS LCD Driver for Low Power Consumption Driving.
(6)
5V or 3.3V single power input. Built- in specific power supplies circuit for LCD
driving. Ultra Low Power Consumption.
(7)
Extended temperature type.
(8)
Portrait(Default) or Landscape Display Type Selectable by Jumper Setting.
(9)
80 or 68 Family MPU Selectable by Jumper Setting
(10)
ROHS compliant.
2 MECHANICAL DATA
Parameter
Stand Value
Unit
Dot size
0.225(W) × 0.225(H)
mm
Dot pitch
0.24(W) × 0.24(H)
mm
Viewing area
62.0 (W) × 81.8 (H)
mm
Module size
73.0(W) × 93.3(H) × 6.7 max (T)
mm
Module size
(w/ Touch panel)
73.0(W) × 93.3(H) × 8.6 max (T)
mm
3 ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Min
Max
Unit
Logic Circuit Supply Voltage
VDD-VSS
-0.3
7.0
V
LCD Driving Voltage
Input Voltage
-VI
-0.3
-0.3
26.0
VDD+0.3
V
V
Operating Temp.
TOP
-20
70
°C
Storage Temp.
TSTG
-30
80
°C
Extended
temp. type
Date : 2006/9/12
AMPIRE CO., LTD.
3
4 ELECTRO-OPTICAL CHARACTERISTICS
Parameter
Logic Circuit
Supply Voltage
Symbol
Condition Min
Typ
Max
----- Electronic Characteristics ----2.6
-5.5
VDD-VSS
---
LCD Driving
Voltage
Input Voltage
Logic Supply
Current
-20 °C
25 °C
22.7
20.7
23.9
21.8
25.1
22.9
70 °C
18.8
19.8
20.8
VIH
--
0.7 VDD
--
VDD
VIL
ICC
---
VSS
--
-20
Unit
Note
V
V
-20 ~ 70 °C for
Extended Temp.
type
V
0.3 VDD V
-mA
----- Optical Characteristics ----Contrast
CR
FSTN type
2
5
--
Rise Time
tr
25°C
--
170
255
ms
Fall Time
tf
25°C
--
380
570
ms
Viewing Angle
Range
θf
25°C &
40
--
--
θb
CR≥2
25
--
--
θl
30
--
--
θr
40
--
--
--
70
--
Frame Frequency
fF
25°C
Note 1
Note 2
Note 3
Deg.
Hz
----- White LED Back-light Characteristics ----Parameter
Symbol
Condition
Min
Typ
Max
Unit
Note
Forward Current
IF
LCM Luminous intensity
-VF=3.2V
---
60
10
80
--
mA
NOTE 4
NOTE 4
Forward Voltage
LED C.I.E
VF
IF=60mA
--
3.2
3.5
X
IF=60mA
0.28
0.31
0.34
Y
IF=60mA
0.29
0.32
0.35
cd/m2
V
Supply Voltage
between A&K
NOTE 5
NOTE 6
(NOTE 4): Luminous intensity is decided by forward current of White LED.
(NOTE 5): White LEDs are with voltage tolerance
(NOTE 6): White LEDs are with color tolerance
Date : 2006/9/12
AMPIRE CO., LTD.
4
* LED Dice number = 4
A
K
Please keep the IF between 60~80mA
Luminous intensity is decided by IF
(NOTE 1) Contrast ratio :
CR = (Brightness in OFF state) / (Brightness in ON state)
( NOTE 2 ) Response time :
(NOTE 3) Viewing angle
Date : 2006/9/12
AMPIRE CO., LTD.
5
Touch Panel Electrical Specification
Parameter
Specification
400 Ω ~ 800 Ω
260 Ω ~ 600 Ω
More than 10MΩ
Less Than 15 ms
ON Resistance
Insulating Resistance
Chattering
Condition
X Axis
Y Axis
DC 25 V
100KΩ Pull- Up
5 BLOCK DIAGRAM
From
MPU
FLM
/RESET
/RD
/WR Controller
RA8835
/CS
A0
DB0~7
LP, M, YDIS
COM.
Driver
LCD Panel
240
320 x 240 Dots
320
SRAM
CP,D0~D3
SEG.
Driver
* Please use the YDIS pin and the inner command of the RA8835 to control Display On/Off.
Date : 2006/9/12
AMPIRE CO., LTD.
6
Power Supply Example
VCC
LCD
MODULE
New driving
method LCD
driver
VCTL
VR
21.8V
VSS
0V
LCD power
circuit
Note: VCTL is about 0.4V
6 INTERFACE DEFINITION
PIN NO.
1
SIGNAL
/RESET
LEVEL
FUNCTION
H/L
Reset Signal
80 Series: Read Signal
H/L
68 Series: Enable Signal(E)
80 Series: Write Signal
H/L
68 Series: R/W Signal
H/L
Chip Select Signal
H/L
Data Type Selection
2
/RD
3
/WR
4
5
/CS
A0
6 ~ 13
DB0~DB7
H/L
14
15
VDD
VSS
-
Power Supply for Logic(+5V or 3.3V)
Power Supply(Ground : 0V)
16
VCTL
-
Contrast Adjustment Input
17
NC
-
18*
SK / X1
-
19*
DO / X2
-
20*
DI / Y1
-
21*
CS / Y2
-
22*
INT
-
No Connection
Serial Clock
Touch Panel Left Signal in X Axis
Serial Data Output
Touch Panel Right Signal in X Axis
Serial Data Input
Touch Panel Upper Signal in Y Axis
T/P controller Chip Select. Active Low
Touch Panel Lower Signal in X Axis
Pen Interrupt
23
24
A
K
-
Data Input(8 bits)
LED Anode
LED Cathode
* 18~22 : SK, DO, DI, CS, INT for Touch Panel controller TSC2046
/ X1, X2, Y1, Y2 for Touch Panel (without TSC2046)
Date : 2006/9/12
AMPIRE CO., LTD.
7
7 TIMING CHARACTERISTICS
7.1
8080 Family Interface Timing
Parameter
Condition
Symbol
Min
Address Hold Time
tAH8
10
Address Setup Time
tAW8
0
System Cycle Time
tCYC
Note
Strobe Pulse Width
CL=100 pF
tOC
150
VDD=2.7~4.5
Data Setup Time
tDS8
120
Data Hold Time
tDH8
5
/RD Access Time
tACC8
Output Disable Time
tOH8
10
Note: For memory control and system control commands:
tCYC8=2tC+tOC+tCEA+75 > tACV +245
For all other commands:
tCYC8=4tC+tOC+30
Max
80
55
Unit
ns
ns
ns
ns
ns
ns
ns
ns
Remark
A0,/CS
/WR,/RD
DB0~DB7
A0,/CS
/WR,/RD
DB0~DB7
(Write)
DB0~DB7
(Read)
Date : 2006/9/12
AMPIRE CO., LTD.
8
7.2
6800 Family Interface Timing
Parameter
Condition
Symbol
Min
System Cycle Time
tCYC6
Note
Address Setup Time
tAW6
10
Address Hold Time
tAH6
0
Data Setup Time
CL=100 pF
tDS6
120
VDD=2.7~4.5
Data Hold Time
tDH6
0
Output Disable Time
tOH6
10
Access Time
tACC6
Enable Pulse Width
tEW
150
Note: For memory control and system control commands:
tCYC6=2tC+tEW+tCEA+75 > tACV +245
For all other commands:
tCYC6=4tC+tEW+30
Max
75
130
-
Unit
ns
ns
ns
ns
ns
ns
ns
ns
Remark
A0,/CS,
R/W
DB0~DB7
E
E
R/W
A0, /CS
DB0~DB7
(Write)
DB0~DB7
(Read)
AC Electrical Characteristics
Date : 2006/9/12
AMPIRE CO., LTD.
9
8 INSTRUCTION SET
Code
Class
Command
Hex
/RD /WR A0
SYSTEM
System SET
Control
SLEEP IN
D7
D6
D5
D4
D3
D2
D1
D0
1
0
1
0
1
0
0
0
0
0
0
1
0
1
0
1
0
1
0
0
1
Command Description
Command read
parameters
Number of
Section
byters
40 Initialized Device and display
8
8.2.1
1
53 Enter Standby mode
0
8.2.2
58, Enable and disable display and
59 display flashing
44 set Display start address and
display regions
1
8.3.1
10
8.3.2
5D Set cursor byte
2
8.3.3
5C Set start address of character
generator RAM
CD CD 4C Set direction of cursor
to movement
1
0
4F
2
8.3.6
0
8.3.4
DISP
ON/OFF
1
0
1
0
1
0
1
1
0
0
D
SCROLL
1
0
1
0
1
0
0
0
1
0
0
CSRFORM
1
0
1
0
1
0
1
1
1
0
1
Display CGRAM
Control ADDR.
1
0
1
0
1
0
1
1
1
CSRDIR
1
0
1
0
1
0
0
1
1
HDOT SCR
1
0
1
0
1
0
1
1
OVLAY
1
0
1
0
1
0
1
1
Drawing CSRW
Control
CSRR
1
0
1
0
1
0
0
1
0
1
0
1
0
Memory MWRITE
Control
MREAD
1
0
1
0
1
1
0
1
0
1
0
0
1
0
5A set horizontal scroll position
1
8.3.7
0
1
1
5B set display overlay format
1
8.3.5
0
1
1
0
46 set cursor address
2
8.4.1
0
0
1
1
1
47 read cursor address
2
8.4.2
0
0
0
0
1
0
42 write to display memory
-
8.5.1
0
0
0
0
1
1
43 read from display memory
-
8.5.2
Note:
1. In general, the internal registers of the RA8835 are modified as each command parameter
is input. However, the microprocessor does not have to set all the parameters of a
command and may send a new command before all parameters have been input. The
internal registers for the parameters that have been input will have been changed but the
remaining parameter registers are unchanged.
2 bytes parameters( where two bytes are treated as 1 data item) are handled as following:
a. CSRW, CSRR: Each byte is processed individually. The microprocessor may read or
write just the low byte of the cursor address.
b. SYSTEM SET, SCROLL, CGRAM ADR. : Both parameter bytes are processed together.
If the command is changed after half of the parameter has been input, the single byte is
ignored.
2. APL and APH are 2-byte parameters, but are treated as two 1-byte parameters.
3. Please refer to RA8835 LCD Controller Data Book for detail.
Date : 2006/9/12
AMPIRE CO., LTD.
10
9 INNER DATA FORMAT
COM1
COM240
#1
D3
D3
D3
D3
#2
D2
D2
D2
D2
D1
D1
D1
D1
D0
D0
D0
D0
D3
#320
D3
D2
D2
D2
D1
D1
D1
D0
D0
D0
Portrait Display Type (Top View)
Date : 2006/9/12
AMPIRE CO., LTD.
11
SEG1
SEG320
#1
D3
D2
D1
D0
D3
D2
#2
D3
D2
D1
D0
D3
#240
D3
D2
D1
D0
D3
-
D3
D2
D1
D0
D2
D3
D2
D1
D0
D2
D3
D2
D1
D0
Landscape Display Type(Top View)
* Regardless Portrait or Landscape type, both are 1/240 duty. The only difference is the
opposite scan direction on Common driver. The character mode of RA8835 could only be
used on Landscape type. The character will be Mirrored on Portrait type.
10 JUMPER SETTING
Item
Option
Jumper Setting
Display Type
Portrait (default)
Landscape
80 family (default)
Pin 1,2 short on JP1&JP2
Pin 2,3 short on JP1&JP2
Pin 1,2 short on JP4
68 family
Pin 2,3 short on JP4
MPU
Date : 2006/9/12
AMPIRE CO., LTD.
Remark
12
11 QUALITY AND RELIABILITY
11.1 TEST CONDITIONS
Tests should be conducted under the following conditions :
Ambient temperature : 25 ± 5°C
Humidity
: 60 ± 25% RH.
11.2
SAMPLING PLAN
Sampling method shall be in accordance with MIL-STD-105E , level II, normal
single sampling plan .
11.3 ACCEPTABLE QUALITY LEVEL
A major defect is defined as one that could cause failure to or materially reduce the
usability of the unit for its intended purpose. A minor defect is one that does not materially
reduce the usability of the unit for its intended purpose or is an infringement from established
standards and has no significant bearing on its effective use or operation.
11.4 APPEARANCE
An appearance test should be conducted by human sight at approximately 30 cm
distance from the LCD module under fluorescent light. The inspection area of LCD panel
shall be within the range of following limits.
Date : 2006/9/12
AMPIRE CO., LTD.
13
11.5 INSPECTION QUALITY CRITERIA
Item
Description of defects
Function
Dimension
Black spots
Short circuit or Pattern cut
Deviation from drawings
Ave . dia . D
area A
area B
Disregard
D≤0.2
3
4
0.2<D≤0.3
2
3
0.3<D≤0.4
0.4<D
0
1
Width W, Length L
A
B
disregard
W≤0.03
3
4
0.03<W≤0.05
1
1
0.05<W≤0.07 , L≤3.0
See line criteria
Average diameter D 0.2 < D < 0.5 mm
for N = 4 , D > 0.5 for N = 1
Rainbow color or newton ring.
Black lines
Bubbles in
polarizer
Color
uniformity
Glass
Scratches
Contrast
ratio
Response
time
Viewing
angle
Class of
Defects
Major
Major
Minor
Acceptable level
(%)
0.65
1.5
2.5
Minor
2.5
Minor
2.5
Minor
2.5
Obvious visible damage.
Minor
2.5
See note 1
Minor
2.5
See note 2
Minor
2.5
See note 3
Minor
2.5
ZONE A active area
ZONE B viewing area
Date : 2006/9/12
AMPIRE CO., LTD.
14
11.6 RELIABILITY
Test Conditions
Test Item
Normal Temp. type
Extended Temp. type
High Temperature Operation
50±3°C , t=96 hrs
70±3°C , t=96 hrs
Low Temperature Operation
0±3°C , t=96 hrs
-20±3°C , t=96 hrs
High Temperature Storage
Low Temperature Storage
Thermal Shock Test
Humidity Test
70±3°C , t=96 hrs
-20±3°C , t=96 hrs
-20°C ~ 25°C ~ 70°C
30 m in. 5 min. 30 min.
( 1 cycle )
Total 5 cycle
Note
80±3°C , t=96 hrs
1,2
-30±3°C , t=96 hrs
1,2
-30°C ~ 25°C ~ 80°C
30 min. 5 min. 30 min. 1,2
( 1 cycle )
Total 5 cycle
40 °C, Humidity 90%, 96 hrs
1,2
Sweep frequency : 10 ~ 55 ~ 10 Hz/1min
Amplitude : 0.75mm
Vibration Test (Packing)
2
Test direction : X.Y.Z/3 axis
Duration : 30min/each axis
Note 1 : Condensation of water is not permitted on the module.
Note 2 : The module should be inspected after 1 hour storage in normal conditions
(15-35°C , 45-65%RH).
Definitions of life end point :
l Current drain should be smaller than the specific value.
l Function of the module should be maintained.
l Appearance and display quality should not have degraded noticeably.
l Contrast ratio should be greater than 50% of the initial value.
Date : 2006/9/12
AMPIRE CO., LTD.
15
12 HANDLING PRECAUTIONS
(1) A LCD module is a fragile item and should not be subjected to strong mechanical shocks.
(2) Avoid applying pressure to the module surface. This will distort the glass and cause a
change in color.
(3) Under no circumstances should the position of the bezel tabs or their shape be modified.
(4) Do not modify the display PCB in either shape or positioning of components.
(5) Do not modify or move location of the zebra or heat seal connectors.
(6) The device should only be soldered to during interfacing. Modification to other areas of
the board should not be carried out.
(7) In the event of LCD breakage and resultant leakage of fluid do not inhale, ingest or make
contact with the skin. If contact is made rinse immediately.
(8) When cleaning the module use a soft damp cloth with a mild solvent, such as Isopropyl or
Ethyl alcohol. The use of water, ketone or aromatic is not permitted.
(9) Prior to initial power up input signals should not be applied.
(10) Protect the module against static electricity and observe appropriate anti-static
precautions.
Date : 2006/9/12
AMPIRE CO., LTD.
16
Date : 2006/9/12
AMPIRE CO., LTD.
晶 采 光 電 科技
適用品號
FFC插件位置
13 OUTLINE DIMENSION
17