A MP I R E SPECIFICATIONS FOR LCD MODULE CUSTOMER CUSTOMER PART NO. AMPIRE PART NO. AT-128128H1FI-00H APPROVED BY DATE Approved For Specifications Approved For Specifications & Sample APPROVED BY Date : 2003/2/21 CHECKED BY AMPIRE CO., LTD. ORGANIZED BY 1 RECORD OF REVISION Revision Date Contents 2002/8/26 New Release 2002/8/27 Added the block of TAB solder dimension (Page 14) 2002/8/29 Modify the LCM outline dimension (Page 14) 2002/8/30 Added the TCP IC dimension (Page 14) 2002/9/23 Modify the LCM outline dimension (Page 15) Added the LCM default setting (Page 6) Modify the LCM passive component (Page 11) 2003/2/21 Date : 2003/2/21 AMPIRE CO., LTD. 2 1 FEATURES (1) Display format : 128×128 dots, 1/128 duty. (2) Construction : LCD panel, TAB IC and FPC. (3) Display type : FSTN , Transflective, Positive , 6 o’clock view (4) Controller : HD66750S or equivalent (5) LCD polarizer : New P1 polarizer. (6) +2.8V single power input. (7) Built-in temp compensation circuit. (8) Extend temperature type. 2 3 MECHANICAL DATA Parameter Stand Value Unit Dot size 0.199(W) × 0.219(H) mm Dot pitch 0.213(W) × 0.233(H) mm Viewing area 30.5(W) ×32.0 (H) mm Module size 36.3(W) × 82.8(H) × 1.4 max.(T) mm ABSOLUTE MAXIMUM RATINGS Parameter Symbol Min Max Unit Logic Circuit Supply Voltage VDD-VSS -0.3 +4.6 V LCD Driving Voltage VLCD-VSS 0 20.0 V Input Voltage VI -0.3 VDD+0.3 V Operating Temp. TOP -20 75 °C Storage Temp. TSTG -30 80 °C Extend temp. type Date : 2003/2/21 AMPIRE CO., LTD. 3 4 ELECTRO-OPTICAL CHARACTERISTICS Parameter Symbol Condition Min Typ Max Unit Note ----- Electronic Characteristics ----Logic Circuit Supply Voltage VDD-VSS -- 2.4 2.8 3.6 V LCD Driving Voltage (FSTN ) VO-VSS -20 °C -- 13.55 -- V 25 °C -- 12.8 -- 70 °C -- 12.13 -- Input Voltage VIH -- 0.7VDD -- VDD V VIL -- -0.3 -- 0.15 VDD V IDD VDD 3.3V -- 0.2 0.4 mA Logic Supply Current ----- Optical Characteristics ( FSTN ) ----Contrast CR 25°C -- 7 -- Rise Time tr 25°C -- 200 -- ms Fall Time tf 25°C -- 200 -- ms Viewing Angle Range θf 25°C & -- 40 -- θb CR≥2 -- 30 -- θl -- 35 -- θr -- 35 -- -- 64 -- Frame Frequency fF 25°C Note 1 Note 2 Note 3 Deg. Hz (NOTE 1) Contrast ratio : CR = (Brightness in OFF state) / (Brightness in ON state) Date : 2003/2/21 AMPIRE CO., LTD. 4 ( NOTE 2 ) Response time : (NOTE 3) Viewing angle Date : 2003/2/21 AMPIRE CO., LTD. 5 5 BLOCK DIAGRAM C1 C16 C17 DOT 1 C64 C65 128X128 LCD PANEL C112 C113 C128 S1 S 128 COM128/1 COM113/16 SEG1/128 SEG128/1 C128 COM64/65 HD66750S (TOP VIEW) COM17/112 COM112/17 COM65/64 COM16/113 COM1/128 LCD MODULE PIN 15 PIN 1 Default Setting: Symbol H/L IM[2:0] LHH L L L NC OPOFF TEST DB[7:0] VTEST Date : 2003/2/21 Description 8080 System 8-bit bus interface Turn on amplifier Test pin 8-bit data bus Test Pin AMPIRE CO., LTD. 6 6 INTERFACE No. Symbol 1 VDD 2 D7 3 D6 4 D5 5 D4 6 D3 7 D2 8 D1 9 D0 10 /RES 11 /CS Chip select at low 12 A0 Select register Lo:Index/status 13 /WR Data Write 14 /RD Data Read 15 VSS Ground (0V) Date : 2003/2/21 Function Power supply for logic circuit 8-bit data bus for 80 series MPU Reset pin .Initializes the LSI when low AMPIRE CO., LTD. Hi:Control 7 7 Software setting Please must follow the blow setting. Otherwise the temp consumption circuit can’t work very well. These setting are related to temp consumption circuit, especially in Power control. Power control R/W 0 0 RS 1 1 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 * * * BS2 BS1 BS0 BT1 BT0 * 0 0 0 0 0 1 1 1 0 1/10 BIAS 7-TIMES DB6 DB5 DB4 DB3 DB2 DB1 * DC1 DC0 AP1 AP0 SLP 0 1 1 0 1 0 4-DIVIDED SMALL DB0 STB 0 Contrast control R/W 0 0 RS 1 1 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 * * * * * * * * 0 0 0 0 0 0 0 0 Date : 2003/2/21 DB7 DB6 DB5 * * CT5 0 0 1 AMPIRE CO., LTD. DB4 DB3 DB2 DB1 DB0 CT4 CT3 CT2 CT1 CT0 0 1 0 0 0 28 (HEX) , 40 (DEC) 8 8 TIMING CHARACTERISTICS 80-SYSTEM VDD=1.8to2.4V Item VDD=2.4to3.6V Unit Symbol Min tCYCW Write 600 Max Min Max -- 380 -- Bus cycle time tCYCR PW LW Lo level pulse width PW LR PW HW Hi-level pulse width PW HR Read 500 800 Write120 -- Read -- 250 350 Write300 70 -- Read 150 -- 150 300 ns Enable rise/fall time tWRr,tWRf -- 25 -- 25 Address set-up time (RS, R/W to E) tAS 50 -- 50 -- Address hold time tAH 20 -- 20 -- Write Data set-up time tDSW 60 -- 60 -- Write Data hold time tH 20 -- 20 -- Read Data delay time tDDR -- 300 -- 200 Read Data hold time tDHR 5 -- 5 -- Date : 2003/2/21 AMPIRE CO., LTD. 9 Date : 2003/2/21 AMPIRE CO., LTD. 10 9 BOM List C5 C11 R5 C7 C8 C9 C12 C10 C4 C3 R1 Q1 C2 C1 R4 RTH R3 C6 Position R1 R2 R3 R5 RTH Q1 C1~C12 R2 Value 330K ohm 1K ohm 6.8K ohm 0 ohm 10K ohm 2SC4617 1UF Remark Resister Resister Resister Resister Thermistor Transistor Capacitor OLB tape size : 33mm x 8 mm Protection tape size : 35mm x 8 mm Date : 2003/2/21 AMPIRE CO., LTD. 11 10 QUALITY AND RELIABILITY 10.1 TEST CONDITIONS Tests should be conducted under the following conditions : Ambient temperature : 25 ± 5°C Humidity : 60 ± 25% RH. 10.2 SAMPLING PLAN Sampling method shall be in accordance with MIL-STD-105E , level II, normal single sampling plan . 10.3 ACCEPTABLE QUALITY LEVEL A major defect is defined as one that could cause failure to or materially reduce the usability of the unit for its intended purpose. A minor defect is one that does not materially reduce the usability of the unit for its intended purpose or is an infringement from established standards and has no significant bearing on its effective use or operation. 10.4 APPEARANCE An appearance test should be conducted by human sight at approximately 30 cm distance from the LCD module under flourescent light. The inspection area of LCD panel shall be within the range of following limits. Date : 2003/2/21 AMPIRE CO., LTD. 12 10.5 INSPECTION QUALITY CRITERIA Item Function Dimension Black spots Black lines Bubbles in polarizer Color uniformity Glass Scratches Contrast ratio Response time Viewing angle Description of defects Class of Defects Major Major Minor Acceptable level (%) 0.65 1.5 2.5 Minor 2.5 Minor 2.5 Minor 2.5 Obvious visible damage. Minor 2.5 See note 1 Minor 2.5 See note 2 Minor 2.5 See note 3 Minor 2.5 Short circuit or Pattern cut Deviation from drawings Ave . dia . D area A area B Disregard D≤0.2 3 4 0.2<D≤0.3 2 3 0.3<D≤0.4 0.4<D 0 1 Width W, Length L A B disregard W≤0.03 3 4 0.03<W≤0.05 1 1 0.05<W≤0.07 , L≤3.0 See line criteria Average diameter D 0.2 < D < 0.5 mm for N = 4 , D > 0.5 for N = 1 Rainbow color or newton ring. Zone A active area Zone B viewing area Date : 2003/2/21 AMPIRE CO., LTD. 13 10.6 RELIABILITY Test Conditions Test Item Extend Temp. type High Temperature Operation 75±3°C , t=96 hrs Low Temperature Operation -20±3°C , t=96 hrs High Temperature Storage 80±3°C , t=96 hrs Low Temperature Storage Thermal Shock Test Humidity Test -30±3°C , t=96 hrs -30°C ~ 25°C ~ 80°C 30 m in. 5 min. 30 min. ( 1 cycle ) Total 5 cycle 40 °C, Humidity 90%, 96 hrs Note 1,2 1,2 1,2 1,2 Sweep frequency : 10 ~ 55 ~ 10 Hz/1min Amplitude : 0.75mm Vibration Test (Packing) 2 Test direction : X.Y.Z/3 axis Duration : 30min/each axis Note 1 : Condensation of water is not permitted on the module. Note 2 : The module should be inspected after 1 hour storage in normal conditions (15-35°C , 45-65%RH). Definitions of life end point : z Current drain should be smaller than the specific value. z Function of the module should be maintained. z Appearance and display quality should not have degraded noticeably. z Contrast ratio should be greater than 50% of the initial value. Date : 2003/2/21 AMPIRE CO., LTD. 14 11 HANDLING PRECAUTIONS (1) A LCD module is a fragile item and should not be subjected to strong mechanical shocks. (2) Avoid applying pressure to the module surface. This will distort the glass and cause a change in color. (3) Under no circumstances should the position of the bezel tabs or their shape be modified. (4) Do not modify the display PCB in either shape or positioning of components. (5) Do not modify or move location of the zebra or heat seal connectors. (6) The device should only be soldered to during interfacing. Modification to other areas of the board should not be carried out. (7) In the event of LCD breakage and resultant leakage of fluid do not inhale, ingest or make contact with the skin. If contact is made rinse immediately. (8) When cleaning the module use a soft damp cloth with a mild solvent, such as Isopropyl or Ethyl alcohol. The use of water, ketone or aromatic is not permitted. (9) Prior to initial power up input signals should not be applied. (10) Protect the module against static electricity and observe appropriate anti-static precautions. Date : 2003/2/21 AMPIRE CO., LTD. 15 Date : 2003/2/21 AMPIRE CO., LTD. 晶采 光 電 科技 適 用 品 號 12 OUTLINE DIMENSION 16