ZETTLER AC-161JYILY-70

A MP I R E
SPECIFICATIONS FOR
LCD MODULE
CUSTOMER
CUSTOMER PART NO.
AMPIRE PART NO.
AC-161JYILY-70
APPROVED BY
DATE
APPROVED BY
Date : 2006/9/7
CHECKED BY
AMPIRE CO., LTD.
ORGANIZED BY
1
RECORD OF REVISION
Revision Date
Page
Contents
Editor
2006/6/7
-
Tony
2006/9/7
3
New Release
Modify Mechanical Data
Date : 2006/9/7
AMPIRE CO., LTD.
Sunglin
2
1
FEATURES
(1) Display format : 16 characters × 1 lines
(2) Construction : LCD panel, Bezel, Zebra ,Yellow-green LED back-light and PCB.
(3) Display type ; STN ,Yellow-green mode , Transflective, 6 o’clock view.
(4) Controller : ST7066-0A.
(5) 5V single power input.
(6) Normal temperature type.
(7) ROHS compliant.
2
3
MECHANICAL DATA
Parameter
Stand Value
Unit
Dot size
1.152 (W) × 1.765(H)
mm
Dot pitch
1.212(W) × 1.825(H)
mm
Character size
6.0(W) × 14.54(H)
mm
Viewing area
120.0(W) × 23.0(H)
mm
Module size
151.0(W) × 40.0(H) × 14.7 max (T)
mm
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Min
Max
Unit
Logic Circuit Supply Voltage
VDD-VSS
-0.3
7.0
V
LCD Driving Voltage
VDD-VO
-0.3
10.0
V
Input Voltage
VI
-0.3
VDD+0.3
V
Operating Temp.
TOP
0
50
°C
Storage Temp.
TSTG
-20
70
°C
Normal temp. type
Date : 2006/9/7
AMPIRE CO., LTD.
3
4
ELECTRO-OPTICAL CHARACTERISTICS
Parameter
Symbol
Condition
Min
Typ
Max
Unit
Note
----- Electronic Characteristics ----Logic Circuit
Supply Voltage
VDD-VSS
--
2.7
--
5.5
V
LCD Driving
Voltage
( STN )
VDD-VO
0 °C
--
--
--
V
25 °C
4.75
5.0
5.25
50 °C
--
--
--
Input Voltage
VIH
--
0.7 VDD
--
VDD
V
VIL
--
VSS
--
0.3 VDD
V
IDD
VDD = 5V
--
2.0
2.4
mA
Logic Supply
Current
0 ~ 50 °C for
Normal Temp.
type
----- Optical Characteristics ( STN ) ----Contrast
CR
25°C
--
5
--
Rise Time
tr
25°C
--
200
300
ms
Fall Time
tf
25°C
--
200
300
ms
Viewing Angle
Range
θf
25°C &
--
40
--
θb
CR≥2
--
35
--
θl
--
35
--
θr
--
35
--
--
64
--
Frame Frequency
fF
25°C
Note 1
Note 2
Note 3
Deg.
Hz
-----Array type LED Back-light Characteristics ----Parameter
Symbol
Condition
Min
Typ
Max
Unit
Note
Forward Voltage
VF
--
--
4.05
4.3
V
Supply Voltage
between A&K
Forward Current
IF
VF=4.05V
--
420
--
mA
VF=4.05V
--
30
--
cd/m2
LCM Luminous intensity
A
K
* LED Dice number = 2×42=84
Date : 2006/9/7
AMPIRE CO., LTD.
4
(NOTE 1) Contrast ratio :CR = (Brightness in OFF state) / (Brightness in ON state)
( NOTE 2 ) Response time :
(NOTE 3) Viewing angle
Date : 2006/9/7
AMPIRE CO., LTD.
5
5
BLOCK DIAGRAM & POWER SUPPLY
Interface
COM1
COM8
16 Character x 1 Line
COM9
E
R/W
RS
DB0~DB7
VDD
VO
VSS
SEG1 ~ SEG40
COM16
ST7066
VDD(+5V)
LCD Bias
Circuit
R1
VO
VR
R2
A
LED-BACKLIGHT
4.05V
K
VSS
LCD Module
5V Power Input
Date : 2006/9/7
AMPIRE CO., LTD.
6
6
INTERFACE
No.
Symbol
1
VSS
Ground (0V)
2
VDD
Supply Voltage for Logic (+5V )
3
VO
Contrast Adjustment
4
RS
Data/Instruction Select
5
R/W
6
E
7
DB0
Data Bus
8
DB1
Data Bus
9
DB2
Data Bus
10
DB3
Data Bus
11
DB4
Data Bus
12
DB5
Data Bus
13
DB6
Data Bus
14
DB7
Data Bus
Date : 2006/9/7
Function
Read/Write Select
Enable Signal
AMPIRE CO., LTD.
7
7
TIMING CHARACTERISTICS
Write Operation
Item
Symbol
VDD=5V
VDD=3.3V
Min
Max
Min
Max
Enable cycle time
tcycE
500
--
1000
--
Enable pulse width
PWEH
230
--
450
--
Enable rise/fall time
tEr,tEf
--
20
--
25
Address set-up time
(RS, R/W to E)
tAS
40
--
60
--
Address hold time
tAH
10
--
20
--
Data set-up time
tDSW
80
--
195
--
Data hold time
tH
10
--
10
--
Date : 2006/9/7
AMPIRE CO., LTD.
Unit
ns
8
Read Operation
Item
Symbol
VDD=5V
VDD=3.3V
Min
Max
Min
Max
Enable cycle time
tcycE
500
--
1000
--
Enable pulse width
PWEH
230
--
450
--
Enable rise/fall time
tEr,tEf
--
20
--
25
Address set-up time
(RS, R/W to E)
tAS
40
--
60
--
Address hold time
tAH
10
--
20
--
Data delay time
tDDR
--
120
--
360
Data hold time
tDRH
5
--
5
--
Date : 2006/9/7
AMPIRE CO., LTD.
Unit
ns
9
8
INSTRUCTION SET
Instruction
Code
Description
E.T.(fOSC
=270
RS R/ D7 D6 D5 D4 D3 D2 D1 D0
KHZ)
W
Clear
0 0 0 0 0 0 0 0 0 1 Write”20H” to DDRAM and set DDRAM
1.53 ms
Display
address to “00H” from AC
Return
0 0 0 0 0 0 0 0 1 -- Sets DD RAM address to “00H” from AC
1.53 ms
Home
and return cursor to its original position if
shifted. The contents of DDRAM are not
changed.
Entry Mode 0 0 0 0 0 0 0 1 I/D SH Assign cursor moving direction and enable
39 µS
SET
the shift of entire display.
Display
0 0 0 0 0 0 1 D C B Set display (D), cursor (C), and blink of
39 µS
ON/OFF
cursor (B) on/off control bit.
Control
Cursor or
0 0 0 0 0 1 S/ R/ -- -- Set cursor moving and display shift control
39 µS
Display
C L
bit, and the direction, without changing of
Shift
DDRAM data.
Function
0 0 0 0 1 DL N F -- -- Sets interface data length (DL:8-bit/4-bit),
39 µS
Set
number of display lines (N:2-line/1-line)
and , display font type (F:5x11dots/5x8
dost).
Set CG
0 0 0 1 AC AC AC AC AC AC Sets CG RAM address in address counter.
39 µS
RAM
5 4 3 2 1 0
Address
Set DD
0 0 1 AC AC AC AC AC AC AC Sets DD RAM address in address counter.
39 µS
RAM
6
5 4 3 2 1 0
Address
Read Busy 0 1 BF AC AC AC AC AC AC AC Whether during internal operation or not
0 µS
Flag and
6
5 4 3 2 1 0 can be known by reading BF. The contents
Address
of address counter can also be read.
Write Data 1 0 D7 D6 D5 D4 D3 D2 D1 D0 Writes data into internal RAM (DD RAM
43 µS
to RAM
/CG RAM).
Read Data 1 1 D7 D6 D5 D4 D3 D2 D1 D0 Reads data from internal RAM (DD RAM
43 µS
from RAM
/CG RAM).
* “--“ : don’t care
Note : When an MPU program with checking the Busy Flag(DB7) is made, it must be
necesssary1/2Fosc is necessary for executing the next instruction by the falling edge of the ‘E’
signal after the Busy Flag(DB7) goes to “LOW”.
Date : 2006/9/7
AMPIRE CO., LTD.
10
9
INITIALIZATION SEQUENCE
10 DD RAM ADDRESS
DIGIT
1
2
3
1 LINE
00 01 02 03 04 05 06 07 40 41 42 43 44 45 46 47
Date : 2006/9/7
4
5
6
7
8
9
10 11 12 13 14 15 16
AMPIRE CO., LTD.
Display Position
DD RAM Address
11
11 FONT TABLE
Date : 2006/9/7
AMPIRE CO., LTD.
12
12 QUALITY AND RELIABILITY
12.1 TEST CONDITIONS
Tests should be conducted under the following conditions :
Ambient temperature : 25 ± 5°C
Humidity
: 60 ± 25% RH.
12.2 SAMPLING PLAN
Sampling method shall be in accordance with MIL-STD-105E , level II, normal
single sampling plan .
12.3 ACCEPTABLE QUALITY LEVEL
A major defect is defined as one that could cause failure to or materially reduce the
usability of the unit for its intended purpose. A minor defect is one that does not materially
reduce the usability of the unit for its intended purpose or is an infringement from established
standards and has no significant bearing on its effective use or operation.
12.4 APPEARANCE
An appearance test should be conducted by human sight at approximately 30 cm
distance from the LCD module under flourescent light. The inspection area of LCD panel
shall be within the range of following limits.
Date : 2006/9/7
AMPIRE CO., LTD.
13
12.5 INSPECTION QUALITY CRITERIA
Item
Function
Dimension
Black spots
Black lines
Bubbles in
polarizer
Color
uniformity
Glass
Scratches
Contrast
ratio
Response
time
Viewing
angle
Description of
defects
Class of
Defects
Major
Major
Minor
Acceptable level
(%)
0.65
1.5
2.5
Minor
2.5
Minor
2.5
Minor
2.5
Obvious visible damage.
Minor
2.5
See note 1
Minor
2.5
See note 2
Minor
2.5
See note 3
Minor
2.5
Short circuit or Pattern cut
Deviation from drawings
Ave . dia . D
area A
area B
Disregard
D≤0.2
3
4
0.2<D≤0.3
2
3
0.3<D≤0.4
0.4<D
0
1
Width W, Length L
A
B
disregard
W≤0.03
3
4
0.03<W≤0.05
1
1
0.05<W≤0.07 , L≤3.0
See line criteria
Average diameter D 0.2 < D < 0.5 mm
for N = 4 , D > 0.5 for N = 1
Rainbow color or newton ring.
Zone A active area
Zone B viewing area
Date : 2006/9/7
AMPIRE CO., LTD.
14
12.6 RELIABILITY
Test Item
Test Conditions
High Temperature Operation
50±3°C , t=96 hrs
Low Temperature Operation
0±3°C , t=96 hrs
High Temperature Storage
70±3°C , t=96 hrs
Low Temperature Storage
Temperature Cycle
Humidity Test
-20±3°C , t=96 hrs
-20°C ~ 25°C ~ 70°C
30 m in. 5 min. 30 min. ( 1 cycle )
Total 5 cycle
40 °C, Humidity 90%, 96 hrs
Note
1,2
1,2
1,2
1,2
Sweep frequency : 10 ~ 55 ~ 10 Hz/1min
Amplitude : 0.75mm
Vibration Test (Packing)
2
Test direction : X.Y.Z/3 axis
Duration : 30min/each axis
Note 1 : Condensation of water is not permitted on the module.
Note 2 : The module should be inspected after 1 hour storage in normal conditions
(15-35°C , 45-65%RH).
Definitions of life end point :
z Current drain should be smaller than the specific value.
z Function of the module should be maintained.
z Appearance and display quality should not have degraded noticeably.
z Contrast ratio should be greater than 50% of the initial value.
Date : 2006/9/7
AMPIRE CO., LTD.
15
13 HANDLING PRECAUTIONS
(1) A LCD module is a fragile item and should not be subjected to strong mechanical shocks.
(2) Avoid applying pressure to the module surface. This will distort the glass and cause a
change in color.
(3) Under no circumstances should the position of the bezel tabs or their shape be modified.
(4) Do not modify the display PCB in either shape or positioning of components.
(5) Do not modify or move location of the zebra or heat seal connectors.
(6) The device should only be soldered to during interfacing. Modification to other areas of
the board should not be carried out.
(7) In the event of LCD breakage and resultant leakage of fluid do not inhale, ingest or make
contact with the skin. If contact is made rinse immediately.
(8) When cleaning the module use a soft damp cloth with a mild solvent, such as Isopropyl or
Ethyl alcohol. The use of water, ketone or aromatic is not permitted.
(9) Prior to initial power up input signals should not be applied.
(10) Protect the module against static electricity and observe appropriate anti-static
precautions.
Date : 2006/9/7
AMPIRE CO., LTD.
16
晶 采 光 電 科技
14 OUTLINE DIMENSION
Date : 2006/9/7
AMPIRE CO., LTD.
17