A6280 3 Bit Constant Current LED Driver with PWM Control Features and Benefits Description ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ The A6280 is a 3 bit constant current LED driver that has a wide range of output currents. The A6280 controls LED luminance with a pulse width modulation (PWM) scheme that gives the application the capability of displaying a billion colors. The overall maximum current is set by an external resistor. 5 to 17 V operation Wide output current range (10 to 150 mA per output) 3 × 7 bit Dot Correction current settings 31 bit shift register 3 ×10 bit PWM luminance settings Buffered output control pins Up to 5 MHz serial / PWM clock frequency Thermal Shutdown / UVLO Packages: 16 pin DIP (suffix A), and 16 pin QFN/MLP (suffix ES) The LED luminance is controlled by performing PWM control on the outputs. The luminance data of the PWM signal for each LED is stored in three 10 bit registers. Each LED can be dot corrected by a 7 bit scalar register that scales the maximum current from 100% down to 36.5%. All the internal latched registers are loaded by a 31 bit serial shift register. One bit is used to control the type of data loaded into the registers, either dot correction / clock divider ratio or luminance data. The remaining 30 bits are used for the data. This helps reduce the pin count of the A6280. To further lower the A6280 pin count, the PWM clock and the serial bus clock share the same pin and work concurrently to control LED luminance and to load data. The A6280 is designed to minimize the number of components needed to drive LEDs with large pixel spacing. Several A6280s can be daisy chained together and controlled by just four control signals (Clock, Serial Data, Latch, and Output Enable). Each of these inputs has buffered outputs on chip. Also, the VIN pin ES, approximate scale 1:1 Continued on the next page… Application Diagram Power Supply Bus VLED Clock Data Strobe Output Enable Microprocessor Control Board Cat5 UTP VIN OutR OutG OutB Clock In Clock Out Data In Data Out Strobe In Strobe Out OE In OE Out VREG A6280 REXT Pixel Board #1 VLED Cat5 UTP VIN OutR OutG OutB Clock In Clock Out Data In Data Out Strobe In Strobe Out OE In OE Out VREG A6280 REXT Cat5 UTP Pixel Board #2 Figure 1. Functional drawing of daisy chained display application. Additional pixel boards with A6280 ICs can be applied. A6280-DS, Rev. 1 Pixel Board #N A6280 3 Bit Constant Current LED Driver with PWM Control Description (continued) can be tied to the LED voltage supply bus, thus eliminating the need for a separate chip supply bus or an external linear regulator. The A6280 is supplied in a 16 pin dual in line (DIP) package (suffix ‘A’) package and in a 16 lead QFN/MLP (suffix ‘ES’) package. The packages are lead (Pb) free with 100% matte-tin leadframe plating. Selection Guide Part Number Packing* Mounting A6280EA-T 25 pieces/tube 16 pin DIP A6280EESTR-T 1500 pieces/reel 16 pin QFN/MLP *Contact Allegro for additional packing options. Absolute Maximum Ratings Characteristic Symbol Notes Rating Units Supply Voltage VIN 17 V Output Voltage VO –0.5 to 17 V Output Current IO 170 mA Ground Current IGND 600 mA Logic Input Voltage Range VI Operating Ambient Temperature TA Maximum Junction Temperature –0.3 to 7 V –40 to 85 ºC TJ(max) 150 ºC Tstg –40 to 150 ºC Storage Temperature Range E Thermal Characteristics Characteristic Symbol Test Conditions* RθJA Package Thermal Resistance Rating Units Package A, 4 layer PCB 38 ºC/W Package ES, 4 layer PCB 40 ºC/W Package ES, 1 layer PCB with 1 in2. Cu area 70 ºC/W *For additional information, refer to the Allegro website. Power Dissipation versus Ambient Temperature 3500 3250 3000 Pa (R cka Power Dissipation, PD (mW) 2750 g QJ A = e 38 A, 4 Pa ºC lay c (R ka /W er g QJ ) PC A = eE 40 S, B ºC 4 la /W ye ) rP CB Pa c (R kage QJA = 7 ES, 1 0º C/W layer PC ) B 2500 2250 2000 1750 1500 1250 1000 750 500 250 0 0 25 50 75 100 125 150 Temperature (°C) Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com 2 A6280 3 Bit Constant Current LED Driver with PWM Control Functional Block Diagram LI LO SDI Shift Registers SDO CI CO OEI Latched Registers OEO REXT Current Regulator 0 Current Regulator 1 Current Regulator 2 REXT VIN Regulator VREG OUT0 OUT1 OUT2 PGND LGND 10 VIN VREG 8 9 LGND 13 SDO 14 LO 15 OEO 11 OUT1 LGND 3 10 PGND VIN 4 9 Package A 12 OUT0 8 REXT 7 2 SDI 11 CI CO 6 1 7 12 OEI OEO 5 REXT VREG LI 13 LI 6 14 SDI LO 4 5 15 OUT2 SDO 3 CI 16 PGND OUT0 2 OEI OUT1 1 16 CO Pin-out Drawings OUT2 Package ES Terminal List Table Name OUT1 OUT0 SDO LO OEO CO REXT VREG LGND VIN CI Number A Package ES Package 1 11 2 12 3 13 4 14 5 15 6 16 7 1 8 2 9 3 10 4 11 5 OEI 12 6 LI SDI OUT2 PGND 13 14 15 16 7 8 9 10 Description Sinking output terminal Sinking output terminal Buffered serial data output after shift registers Buffered latch output Buffered output enable output Buffered clock output An external resistor at this terminal establishes overall output current Regulator decoupling Logic ground Chip power supply voltage Serial and PWM clock input Output enable input; when low (active), the output drivers are enabled; when high (inactive), all output drivers are turned off (blanked) Latch input terminal; serial data is latched with high-level input Serial data input to shift registers Sinking output terminal Power ground Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com 3 A6280 3 Bit Constant Current LED Driver with PWM Control OPERATING CHARACTERISTICS, valid at TA = 25°C, VIN = 4.75 to 17.0 V, unless otherwise noted Characteristic ELECTRICAL CHARACTERISTICS Quiescent Supply Current Operating Supply Current Symbol Test Conditions Min. Typ. Max. Units IDD IDD fCLKIN = 0.0 Hz fCLKIN = 5 Mhz VIN rising VIN falling IO =15 mA, VIN = 17 V IO =15 mA, VIN = 4.75 V REXT = 5 kΩ, scalar = 100% REXT = 15 kΩ Output to output variation—all outputs on, REXT = 5 kΩ – – 3.5 3.0 4.6 – 135 44 7 1.0 – – 2.0 – – –20 – 3.8 150 100 – – – – – – – – 200 150.0 – – – ±1 – – – 150 – – – 300 200 ±1 165 15 5.0 15.0 4.5 4.0 5.4 600 165 54 7 3.0 ±3 1.0 – 0.8 – 20 0.4 – 600 400 – – – mA mA V V V mV mA mA % V % μA V V mV μA V V kΩ kΩ bit °C °C tH(CLK) tSU(D) tH(D) tSU(LE) tH(LE) tSU(OE) 20 20 20 20 20 40 – – – – – – – – – – – – ns ns ns ns ns ns tP(OE)2 – 200 – ns – – – – – – – 200 50 30 10 10 50 100 – 100 60 – – – – ns ns ns ns ns ns ns tP(SDO) – 50 100 ns tP(OE) – 50 100 ns tP(LE) tP(CLK) tw(CLK) fCLKIN – – 70 – 50 50 100 – 100 100 130 6 ns ns ns MHz Undervoltage Lockout VIN(UV) VREG Voltage Range VREG Dropout Voltage VREG VDO Output Current (any single output) IO Output to Output Matching Error* Output Voltage Range Load Regulation Output Leakage Current Err VDS(min) Logic Input Voltage Logic Input Voltage Hysteresis Logic Input Current Logic Output Voltage Input Resistance Output Dot Correction Error Thermal Shutdown Temperature Thermal Shutdown Hysteresis SWITCHING CHARACTERISTICS Clock Hold Time Data Setup Time Data Hold Time Latch Setup Time Latch Hold Time Output Enable Set Up Time Output Enable Falling to Outputs Turning ON Propagation Delay Time Clock to Output Propagation Delay Time Logic Output Fall Time Logic Output Rise Time IDSX VIH VIL IIN VOL VOH RI TJTSD TJhys tP(OUT) tBF tBR Output Fall Time (Turn Off) tf Output Rise Time (Turn On) tr Clock Falling Edge to Serial Data Out Propagation Delay Time Output Enable In to Output Enable Out Propagation Delay Latch In to Latch Out Propagation Delay Clock In to Clock Out Propagation Delay Clock Out Pulse Duration Maximum CLKIN Frequency *Err = [IO (min or max) – IO(av)] / IO(av). I%Diff / VDS VOH = 17 V All digital inputs VIN = 0 to 5 V VIN ≥ 5.0 V, IO = ±2 mA OEI pin, pull-up LI pin, pull-down REXT = 5 kΩ; LSB Temperature increasing VDS = 1.0 V, IO = 150 mA COB = 50 pF, 4.5 to 0.5 V COB = 50 pF, 0.5 to 4.5 V CO = 10 pF, 90% to 10% of IO = 10 mA CO = 10 pF, 90% to 10% of IO = 10 mA CO = 10 pF, 90% to 10% of IO = 10 mA CO = 10 pF, 90% to 10% of IO = 10 mA Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com 4 A6280 3 Bit Constant Current LED Driver with PWM Control Timing Diagram 0 Clock tSU (D ) 1 2 3 4 5 6 7 15 8 tw(C L K) tH( D) D30 D29 D28 D27 D26 D25 D24 D23 D22 Serial Data In 16 30 D8 D7 D0 tP(SD O) Don’t Care Serial Data Out D30 tSU (L E ) Latch Enable In tH (L E ) tP( LE) Latch Enable Out Figure 2. Shift Register Timing t0 T1 T2 1 2 TN Clock IN PWM Counter OUT0 Luminance Data= 0 0 1023 0 1 2 X 0 tP (OU T) tP( OU T) tP (OU T) OUT1 Luminance Data= 2 tP (OU T) OUT2 Luminance Data= 1023 t w (OE) Output Enable In tP(OE ) Output Enable Out Figure 3. PWM Counter and Output Timing Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com 5 A6280 3 Bit Constant Current LED Driver with PWM Control Functional Description Shift Registers Output Buffers The A6280 has a 31 bit shift register that loads data through the Serial Data In (SDI) pin. The shift registers operate by a first-in first-out (FIFO) method. The most significant bit (MSB, bit 30) is the first bit shifted in and the least significant bit (LSB, bit 0) is shifted in last. The serial data is clocked by a rising edge of the Clock In (CI) pin. The Serial Data Out (SDO) pin is updated to the state of bit 30 on the falling edge of the CI pin. This will prevent any race conditions and erroneous data that might occur while propagating information through multiple A6280 that are daisy chained together. The contents of the shift registers will continue to propagate on every rising edge of the CI pin. The information in the shift registers is latched on a rising edge of the Latch In (LI) pin. The latched data remains latched on a rising Output Enable In (OEI) signal. The A6280 is designed to allow daisy chaining many A6280s together. It has the ability to pass the clock, data, latch, and output enable signals from one A6820 to the next without any loss of data due to duty cycle skewing or signal degradation. The A6820 is equipped with output buffers that allow the data signals to travel over long distances through strings of A6280s without the need for extra driving hardware. The A6280 drives these signals to TTL levels. Each of the A6280 inputs have a corresponding buffered output: • Clock In (CI) pin to Clock Out (CO) pin • Latch In (LI) pin to Latch Out (LO) pin • Output Enable In (OEI) pin to Output Enable Out (OEO) pin • Serial Data In (SDI) pin to Serial Data Out (SDO) pin Latch In Latch Out Shift Registers Serial Data In 0 …….. 9 10 …….. 19 20 …….. 29 30 Serial Data Out Latched Registers Clock In Current Scalar 0 7 bits Output Enable In Clock Divider 2 bits Unused 1 bit Current Scalar 1 7 bits Unused 3 bit Current Scalar 2 7 bits Unused Test Bit 1 bit 1 bit PWM Counter 0 10 bits PWM Counter 1 10 bits PWM Counter 2 10 bits Cur Reg0 Cur Reg1 Cur Reg2 Test Bit 1 bit Bit 30 “1” Clock Out “0” Output Enable Out Regulator Vin Vreg Rext Out0 Out1 Out2 GND GND Figure 4. Functional Diagram Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com 6 A6280 3 Bit Constant Current LED Driver with PWM Control PWM Luminance Control The A6280 controls the intensity of each LED by PWMing the current of each output. The A6280 has three 10 bit luminance registers, one for each output. These luminance registers set the PWM count value at which the outputs switch off during each PWM cycle. Each 10 bit luminance register gives 1023 levels of light intensity. The duty cycle, DC (%), can be determined by the following equation: DC = [(PWMn + 1) / 1024] ×100 , where PWMn is the PWM value greater than zero that is stored in the luminance register. When the luminance register is set to zero, the outputs remain off for the duration of the PWM cycle for a 0% DC. When a luminance register is set to 1023, the LED for that output remains on (100% DC) when OEI is active and begins the PWM cycle. The output remains on when the PWM counter rolls over and begins a new count. The PWM counter begins counting at zero and increments only when the OEI pin is held low. When the PWM counter reaches the count of 1023, the counter resets to zero and continues incrementing. The counter resets back to zero either on a rising edge of OEI, upon recovery from UVLO, or when powering up. Latching new data into the luminance registers will not reset the PWM counter. There is a programmable clock divider that attenuates the clock input of the CI pin. See table 1 for bit assignments of the programmable clock divider. The PWM counter is incremented on every rising edge of the CI pin divided by the clock divider count value when the OEI pin is low. For example, if the clock divider is programmed to divide the CI by 2, then the PWM counter will increment once every 2 CI cycles. Given a 5 MHz CI frequency, the clock period would be 200 ns. The total number of possible colors of an RGB pixel is over 1 billion. Refer to figure 6 for the mapping of shift register bits to latches. Output Current Selection The overall maximum current is set by the external resistor, REXT , connected between REXT and LGND. Once set, the maximum current remains constant regardless of the LED voltage variation, supply voltage variation, temperature, or other circuit parameters that could otherwise affect LED current. The maximum output current can be calculated using the following equation: IO(max) = 753.12 / REXT. The relationship of the value selected for REXT and IO is shown in figure 5. Internal Linear Regulator The A6280 has a built-in linear regulator. The regulator operates from 5 to 17 V, and is intended to allow the VIN pin of the A6280 to connect to the same supply as the LEDs. This will simplify board design by eliminating the need for a chip supply bus and external voltage regulators. The VREG pin is used by the internal liner regulator as an energy reservoir. This pin is for internal use only and is not intended as an external power source. The VREG pin should have a 1.0 μF, 10 V ceramic capacitor connected between the VREG pin and LGND. The capacitor should be located as close to the VREG pin as possible. Bits 7 0 1 0 1 8 0 0 1 1 Divide By Count ×1 (no division) ×2 ×4 ×8 The clock divider data in the shift registers is latched on a rising edge of the Latch In (LI) pin. The latched clock divider data remains latched on a rising OEI signal. IO (mA) Table 1. Clock Divider Configurations 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 0 5 15 25 35 45 REXT (kΩ) 55 65 75 Figure 5. Output Current versus External Resistor, REXT Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com 7 A6280 3 Bit Constant Current LED Driver with PWM Control Dot Correction Control Thermal Shutdown (TSD) The A6280 can further control the maximum output current for each output by setting the three 7 bit dot correction registers with scale data that ranges from 36.5% to 100% of the overall maximum output current that is set by the REXT resistor. This feature is useful because not every type of LED (red, green, or blue, for example) has the same level of brightness or intensity for any given current, and the brightness could be different even from LED to LED of the same type. By scaling the output currents so that all the LEDs have matched intensities, the application will have full color depth when using the PWM counters. The dot correction current can be calculated by the following equation: When the junction temperature of the A6280 reaches the thermal shutdown temperature threshold, TJTSD (165°C typical), the outputs will shut off until the junction temperature cools down below the recovery threshold, –TJTSD –∆TJ ( 15°C typical). The shift registers and output latches will remain active during the TSD event. Therefore there is no need to reset the data in the output latches. Undervoltage Lockout The A6280 includes an internal undervoltage lockout (UVLO) circuit that disables the driver outputs in the event of the logic supply voltage dropping below a minimum acceptable level. This prevents the display of erroneous information, a necessary function for some critical applications. The shift registers will not shift any data in a UVLO condition. Upon recovery of the logic supply voltage and on power up, all internal shift registers and latches will be set to zero. IOn = IOn(max) × (Scalen / 2 + 36.5) Refer to figure 6 for the bit configurations for the scalar registers. The dot correction data in the shift registers is latched on a rising edge of the Latch In (LI) pin. The latched dot correction data remains latched on a rising OEI signal. The default output current when the A6280 is powered up or recovers from a UVLO is 36.5% of the current set by the REXT resistor. Package Power Dissipation Ballast Resistors The maximum allowable package power dissipation is determined as: The voltage on the outputs should be kept in the range 1 to 3 V. If the voltage goes below 1V, the current will begin to rolloff as the driver runs out of headroom. At VO above 3 V, the power dissipation may become a problem, as each output contributes VO × ILED of power loss in the output sink driver. Typically the power supply nominal voltage is chosen to keep the output voltage in this range. Alternatively, series resistors can be added to dissipate the extra power and keep the output voltage within the recommended range. PD(max) = (150 – TA) / RθJA . The actual package power dissipation is: PD(act) = DC0 × VDS0 × IOUT0 + DC1 × VDS1 × IOUT1 + DC2 × VDS2 × IOUT2 + VIN × IIN . When calculating power dissipation, the total number of available device outputs is usually used for the worst-case situation (i.e., displaying all 3 LEDs at 100% DC). Bits 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 PWM Counter 0 Dot Correction Register 0 Clock 0 Divider PWM Counter 1 Dot Correction Register 1 0 0 0 PWM Counter 2 Dot Correction Register 2 29 30 0 0 ATB* ATB* 1 *Allegro Test Bit (ATB). Reserved for Allegro internal testing. Always set to zero (0) in the application. Figure 6. Register Configuration Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com 8 A6280 3 Bit Constant Current LED Driver with PWM Control Applications Drawings Tie LGND and PGND to PAD externally PAD 16 CO 15 OEO 14 LO 13 SDO OUT0 REXT 1 A6280 ES OUT2 Output Enable VREG 5 CI 6 OEI 7 LI 8 SDI Clock Data Strobe 2 9 OUT1 System Logic 3 10 kΩ PGND VIN 4 LGND 1 μF X5R 10 11 12 VOn 1 to 3 V + 8.5 V Blue LEDs 10 μF A6280 ES Maximum of 250 LEDs Green Red LEDs LEDs – Figure 7. Application Driving 3 RGB LEDs at 75 mA Peak Tie LGND and PGND to PAD externally 9 OUT0 REXT PAD 10 11 10 μF 75 V A6280 ES 12 VOn 1 to 3 V + 10 V 1 16 CO 15 OEO 14 LO 13 SDO A6280 ES OUT2 Output Enable VREG 5 CI 6 OEI 7 LI 8 SDI Clock Data Strobe 2 OUT1 System Logic 3 5 kΩ PGND VIN 4 LGND 1 μF 10 V Maximum of 250 LEDs 2Ω 0.5 W – Figure 8. Application Driving High Power LED at 450 mA Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com 9 A6280 3 Bit Constant Current LED Driver with PWM Control A Package, 16 Pin DIP Preliminary dimensions, for reference only Dimensions in inches Metric dimensions (mm) in brackets, for reference only (reference JEDEC MS-001 BB) Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Terminal #1 mark area .775 19.69 .735 18.67 A .014 0.36 .008 0.20 B 16 .280 7.11 .240 6.10 .430 10.92 MAX .300 .7.62 A 1 2 .195 4.95 .115 2.92 .210 5.33 MAX SEATING PLANE C .015 0.38 MIN .005 0.13 MIN .070 1.78 .045 1.14 .100 .2.54 16X .150 3.81 .115 2.92 .022 .056 .014 .036 .010 [0.25] M C 10 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com A6280 3 Bit Constant Current LED Driver with PWM Control ES Package, 16 Pin QFN/MLP 3.15 .124 2.85 .112 A B 16 1 Preliminary dimensions, for reference only (reference JEDEC MO-220WEED-4) Dimensions in millimeters U.S. Customary dimensions (in.) in brackets, for reference only Dimensions exclusive of mold flash, gate burrs, and dambar protrusions Exact case and lead configuration at supplier discretion within limits shown A Terminal #1 mark area A 2 3.15 .124 2.85 .112 B Exposed thermal pad (reference only, terminal #1 identifier appearance at supplier discretion) C Reference land pattern layout (reference IPC7351 QFN50P300X300X80-17W4M); adjust as necessary to meet application process requirements and PCB layout tolerances; when mounting on a multilayer PCB, thermal vias at the exposed thermal pad land can improve thermal dissipation (reference EIA/JEDEC Standard JESD51-5) 16X SEATING PLANE 0.08 [.003] C 16X 0.30 .012 0.18 .007 0.80 .031 0.70 .028 0.10 [.004] M C A B 0.05 [.002] M C 0.50 .020 0.20 .008 REF 0.30 .012 NOM 0.90 .035 NOM 0.05 .002 0.00 .000 0.50 .020 NOM 16 C 1.70 .067 NOM C 1 1.70 .067 NOM 12X 0.20 .008 MIN 4X 0.20 .008 MIN 3.10 .122 NOM 2 B 1.70 .067 NOM .067 1 16 16X 0.20 .008 MIN 1.70 NOM 0.23 x 0.23 .009 x .009 REF 0.50 .020 0.30 .012 3.10 .122 NOM The products described here are manufactured under one or more U.S. patents or U.S. patents pending. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support devices or systems without express written approval. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. Copyright©2006 AllegroMicrosystems, Inc. 11 Allegro MicroSystems, Inc. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com