AMI AMIS-53000-M

AMIS-53000 Frequency Agile Transceiver
AMIS-53000 Frequency Agile Transceiver
Data Sheet
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
1
Data Sheet
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Table of Contents
1.0 Overview of the AMIS-53000.............................................................................................................................................................. 5
1.1 Applications for the AMIS-53000 ...................................................................................................................................................... 5
1.2 Key Features .................................................................................................................................................................................... 5
1.3 Technical Features ........................................................................................................................................................................... 5
1.4 Circuit Overview................................................................................................................................................................................ 6
1.4.1. Transmitter ..........................................................................................................................................................................................................6
1.4.2. Receiver ...............................................................................................................................................................................................................6
2.0 Operational Specifications ................................................................................................................................................................ 8
2.1 Absolute Maximum Ratings .............................................................................................................................................................. 8
2.2 Recommended Operating Conditions ............................................................................................................................................... 8
2.2.1. Parametric Voltage and Current Levels ............................................................................................................................................................8
2.3 Operational Specifications ................................................................................................................................................................ 9
3.0 Block Diagrams ................................................................................................................................................................................ 12
3.1 AMIS-53000 Overall Block Diagram............................................................................................................................................... 12
3.2 Package.......................................................................................................................................................................................... 12
3.2.1. Pin Definition .....................................................................................................................................................................................................12
3.2.2. Block Diagram/Pin Definition...........................................................................................................................................................................13
3.2.3. Physical Characteristics...................................................................................................................................................................................14
4.0 Acronyms.......................................................................................................................................................................................... 15
5.0 Hardware Description ...................................................................................................................................................................... 16
5.1 Frequency....................................................................................................................................................................................... 16
5.2 Receiver.......................................................................................................................................................................................... 18
5.2.1. Receiver Low Noise Amplifier (LNA)...............................................................................................................................................................19
5.2.2. IF Filter ...............................................................................................................................................................................................................20
5.2.3. Data Filter...........................................................................................................................................................................................................20
5.3 Transmitter...................................................................................................................................................................................... 20
5.4 Single Antenna Option .................................................................................................................................................................... 21
5.5 Peak................................................................................................................................................................................................ 22
5.6 ADC ................................................................................................................................................................................................ 23
5.7 Control Interface Serial Bus ............................................................................................................................................................ 23
5.8 TX/RX Data Interface Serial Bus .................................................................................................................................................... 24
5.9 System Clock.................................................................................................................................................................................. 25
5.10 Power and Grounds ...................................................................................................................................................................... 25
5.11 Design Suggestions ...................................................................................................................................................................... 26
6.0 User’s Guide ..................................................................................................................................................................................... 28
6.1 Control Serial Interface Bus Description ......................................................................................................................................... 28
6.1.1. Control Interface Protocol................................................................................................................................................................................28
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
2
AMIS-53000 Frequency Agile Transceiver
Data Sheet
6.1.2. Serial Control Interface: Configuration...........................................................................................................................................................30
6.1.3. 3-Wire Interface Mode.......................................................................................................................................................................................31
2
6.1.4. I C Interface .......................................................................................................................................................................................................32
6.2 Command Register ......................................................................................................................................................................... 35
6.3 Functional Flow Diagrams .............................................................................................................................................................. 36
6.4 Frequency....................................................................................................................................................................................... 40
6.4.1. Frequency Control ............................................................................................................................................................................................40
6.4.2. 10kHz Oscillator ................................................................................................................................................................................................44
6.4.3. System Clock.....................................................................................................................................................................................................44
6.4.4. Quick Start .........................................................................................................................................................................................................45
6.4.5. Self Calibration..................................................................................................................................................................................................45
6.5 Receiver.......................................................................................................................................................................................... 47
6.5.1. Receiver Circuit Brief Overview ......................................................................................................................................................................48
6.6 Transmitter ..................................................................................................................................................................................... 57
6.6.1. TX Config ...........................................................................................................................................................................................................58
6.6.2. Output Power.....................................................................................................................................................................................................59
6.6.3. Preamble Length ...............................................................................................................................................................................................59
6.6.4. FM Transmit Data Shaping...............................................................................................................................................................................59
6.7 Idle .................................................................................................................................................................................................. 60
6.7.1. Idle Config..........................................................................................................................................................................................................60
6.7.2. Sniff Mode Operation........................................................................................................................................................................................61
6.7.3. Burst Transmit Data..........................................................................................................................................................................................65
6.7.4. Housekeeping....................................................................................................................................................................................................67
6.8 Idle Return ...................................................................................................................................................................................... 68
6.9 EE ................................................................................................................................................................................................... 69
6.9.1. Write EE .............................................................................................................................................................................................................69
6.9.2. Load EE..............................................................................................................................................................................................................69
6.10 Calibrate ....................................................................................................................................................................................... 69
6.10.1. Internal Trim ....................................................................................................................................................................................................70
6.10.2. Calibrate Quick Start Oscillator .....................................................................................................................................................................71
6.10.3. Calibrate 10kHz Oscillator..............................................................................................................................................................................71
6.10.4. Calibrate PLL ...................................................................................................................................................................................................71
6.10.5. Calibrate LNA ..................................................................................................................................................................................................71
6.11 ROM 2 REGS ............................................................................................................................................................................... 71
6.12 Chip Reset .................................................................................................................................................................................... 72
6.13 ADC Conversion ........................................................................................................................................................................... 72
6.13.1. ADC Conversion Results................................................................................................................................................................................72
6.13.2. Single ADC Conversion..................................................................................................................................................................................73
6.13.3. Continuous ADC Conversion.........................................................................................................................................................................74
7.0 Data Interface.................................................................................................................................................................................... 75
7.1.1. Chip Address MSB1..........................................................................................................................................................................................77
7.1.2. Chip Address LSB.............................................................................................................................................................................................77
7.1.3. Data Rate/Format ..............................................................................................................................................................................................77
7.1.4. General Options A.............................................................................................................................................................................................78
7.1.5. General Options B.............................................................................................................................................................................................79
7.1.6. Start of Frame....................................................................................................................................................................................................80
7.1.7. Data Rate 1.........................................................................................................................................................................................................80
7.1.8. Data Rate 0.........................................................................................................................................................................................................80
7.1.9. CRC Polynomial ................................................................................................................................................................................................80
7.1.10. Default Length of Packet ................................................................................................................................................................................81
7.1.11. Broadcast ID 1 .................................................................................................................................................................................................81
7.1.12. Broadcast ID 0 .................................................................................................................................................................................................81
7.2 TX/RX Data Interface Protocol........................................................................................................................................................ 81
7.2.1. AMIS-53000 in Master Mode.............................................................................................................................................................................83
7.2.2. AMIS-53000 in Slave Mode ...............................................................................................................................................................................84
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
3
AMIS-53000 Frequency Agile Transceiver
Data Sheet
7.2.3. Manchester Operation ......................................................................................................................................................................................84
7.2.4. Packet Framing .................................................................................................................................................................................................84
7.2.5. Use ID .................................................................................................................................................................................................................85
7.2.6. Length of Packet Enable ..................................................................................................................................................................................85
7.2.7. CRC Enable........................................................................................................................................................................................................85
7.2.8. SOF Byte ............................................................................................................................................................................................................86
7.2.9. Timing Diagrams for Various Packet Framing Modes...................................................................................................................................86
8.0 General System Functions .............................................................................................................................................................. 90
8.1 Pull up Disable ................................................................................................................................................................................ 90
8.2 Brown-Out POR .............................................................................................................................................................................. 90
8.3 Temperature Sensor ....................................................................................................................................................................... 90
8.3.1. Crystal Temperature Compensation ...............................................................................................................................................................91
8.4 Software.......................................................................................................................................................................................... 91
8.4.1. AMIS Part Revision Code .................................................................................................................................................................................91
9.0 Built-in Test Functions..................................................................................................................................................................... 92
9.1 TM Unlock Register ........................................................................................................................................................................ 92
9.2 Test Registers................................................................................................................................................................................. 92
9.2.1. IF Amp Manual Trim A ......................................................................................................................................................................................92
9.2.2. IF Amp Manual Trim B ......................................................................................................................................................................................92
9.2.3. PLL Manual Trim ...............................................................................................................................................................................................92
9.2.4. PLL Test Modes.................................................................................................................................................................................................93
9.2.5. Power Down RF Sections.................................................................................................................................................................................93
9.2.6. Analog Test Mode .............................................................................................................................................................................................93
9.2.7. RF Test Modes...................................................................................................................................................................................................93
9.2.8. Analog Test MUX...............................................................................................................................................................................................93
9.2.9. RF Test MUX ......................................................................................................................................................................................................94
9.2.10. Digital Test MUX A ..........................................................................................................................................................................................94
9.2.11. Digital Test MUX B ..........................................................................................................................................................................................94
9.2.12. Digital Test MUX C ..........................................................................................................................................................................................95
9.2.13. Digital Test Mode A.........................................................................................................................................................................................95
9.2.14. Digital Test Mode B.........................................................................................................................................................................................95
9.2.15. Digital Test Mode C.........................................................................................................................................................................................95
9.2.16. Digital Test Mode D.........................................................................................................................................................................................95
9.2.17. Memory Test Mode Address ..........................................................................................................................................................................95
9.2.18. Memory Test Mode Data.................................................................................................................................................................................95
10.0 Register Definition.......................................................................................................................................................................... 96
11.0 Applications.................................................................................................................................................................................... 98
12.0 Ordering Information...................................................................................................................................................................... 99
13.0 Company or Product Inquiries ...................................................................................................................................................... 99
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
4
AMIS-53000 Frequency Agile Transceiver
Data Sheet
1.0 Overview of the AMIS-53000
The AMIS-53000 is the latest highly flexible member of AMI Semiconductor’s ASTRIC™ family of single-chip wireless transceivers. It is
ideally suited for low to moderate data rate, low power, sub 1GHz, narrow band, FSK/GFSK/OOK, multiple channel, wireless
applications in the medical, automotive and industrial markets. The AMIS-53000 can easily be interfaced to a base band processor via
a serial interface bus.
1.1 Applications for the AMIS-53000
•
•
•
•
•
•
•
•
•
•
•
Medical Implantable Communication Systems (MICS)
Wireless Medical Telemetry Systems
Wireless Sensors
RFID
Remote Monitoring
Access Control and Security
Keyless Entry
Mobile Wireless Data Terminals
Keyless Entry
Tire Pressure Monitors
Wireless Toys
1.2 Key Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Medical implant communication protocol support
Very low power single-chip CMOS transceiver
Patented Quick Start crystal oscillator
Low power receive Sniff Mode™
Periodic transmit using Burst mode
Internal low power 10kHz oscillator
Internal self calibration functions
SPI/I2C interface bus
3-wire/4-wire serial data interface
Two analog to digital converter channels
Internal fractional N frequency synthesizer
On/off shift key/frequency shift key modulation/Gaussian FSK (BT = 1)
Internal temperature sensor
Minimal external components
1.3 Technical Features
•
•
•
•
•
•
Operating voltage range: 2.2 to 3.3V
Operating temperature range: -40° to +85oC
Operating frequency range: 300 to 928MHz
Data rate:
o 1 to 19.2kbps (OOK)
o 2 to 128kbps (FSK/GFSK)
Transmit output power:
o +15dBm max (high power)
o +0dBm max (low power)
Transmit current: 50mA typical (15dBm)
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
5
AMIS-53000 Frequency Agile Transceiver
•
•
•
Data Sheet
Receiver sensitivity
o –115dBm (OOK @ 1kbps)
o –105dBm (FSK @ 20kbps)
Receiver current: 12mA (continuous)
Minimum RX energy detect time: 130uS (Sniff)
1.4 Circuit Overview
1.4.1. Transmitter
The AMIS-53000 uses a driver and class E power amplifier to output the on/off shift keyed or frequency shift keyed RF waveforms. The
class E power amplifier has two output power ranges allowing more efficient output power for the one setting up to 0dBm output and the
other setting for output power greater than 0dBm. The class E power amplifier can achieve output power of +12dBm to +15dBm for
frequencies in the range of 300MHz to 915MHz. The output power is programmable in each of the two output power bands.
The transmit data can be NRZ or Manchester encoded. Data can also be modulated as on/off shift keyed or frequency shift keyed.
Data rates for the OOK modulation can be as high as 19.2kbps. Data rates for the FSK/GFSK modulation can be as high as 128kbps.
The carry frequency deviation for the FSK modulation is programmable, typically one half to one times the data rate.
The transmit data output can be wave shaped with a Gaussian format. This can reduce the occupied bandwidth of the signal.
1.4.2. Receiver
The AMIS-53000 has a single receiver channel and a single transmit channel, which can be connected to individual antennas or can be
combined into a single antenna. The receiver uses four different methods to receive and recover data that has been on/off shift keyed
or frequency shift keyed modulated. The FSK/GFSK data is recovered using either a PLL circuit or a FFT circuit along with a CDR
circuit. The OOK data is recovered using an RSSI circuit along an optional CDR circuit. It is suggested that the CDR circuit be used
when receiving OOK signals.
1.4.2.1.
On/Off Shift Key Modulation
The AMIS-53000 uses a logarithmic received signal strength indicator (RSSI) detector to recover the data from the on/off shift keyed
modulated waveform. Data rates can be up to 19.2kbps. The AMIS-53000 has eight discrete data filters for common baud rates. The
receiver can detect either NRZ or Manchester encoded data.
1.4.2.2.
Low Data Rate Frequency Shift Key Modulation
The AMIS-53000 uses a digital PLL detector to recover the data from the frequency shift keyed data below 20kbps. The recovered
data waveform is applied to the clock and data recovery circuit to produce the digital data and a synchronized clock. The receiver can
detect either NRZ or Manchester encoded data.
1.4.2.3.
High Data Rate Frequency Shift Key Modulation
The AMIS-53000 uses a fast fourier transform (FFT) to recover data from frequency shift keyed modulated waveforms when the data
rate is higher than 20kbps. The data rate can be as high as 128kbps. The demodulated data waveform is applied to the clock and data
recovery circuit to produce the digital data and a synchronized clock. The receiver can detect either NRZ or Manchester encoded data.
1.4.2.4.
Clock and Data Recovery
The AMIS-53000 uses a clock and data recovery circuit along with the frequency shift keyed or on/off shift keyed data detector circuits
to recover the data stream. The CDR circuit synchronizes a clock with the data rate of the received data. This same circuit can be
used with the on/off shift keyed waveform.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
6
AMIS-53000 Frequency Agile Transceiver
1.4.2.5.
Data Sheet
Manchester Data Encoding
The AMIS-53000 can encode the data as NRZ or Manchester.
1.4.2.6.
Oscillators
The AMIS-53000 requires a single external crystal working with the internal VCO and PLL to generate frequencies from 300MHz to
928MHz. The AMIS-53000 has internal capacitors that eliminate the need for external load capacitors when using a typical 24MHz
external crystal. The VCO requires an external inductor and capacitor (including internal capacitance) to produce the desired transmit
or receive RF frequency. The AMIS-53000 generates the desired RF transmit and receive frequencies from 300MHz to 928MHz by
selecting the proper inductor and capacitor value along with programming the frequency in the AMIS-53000. A patented Quick Start
circuit is used to force the crystal oscillator on to the desired frequency in microseconds rather than in milliseconds.
A low power internal 10kHz oscillator provides the timing for Sniff, Burst and housekeeping. The AMIS-53000 self-calibration circuits
can tune this oscillator to within two percent of 10kHz.
1.4.2.7.
Interface Serial Bus
The AMIS-53000 has separate interfaces for data and control. The transfer of TX/RX data between the AMIS-53000 and an external
host/controller is done with a 3-wire serial interface or a 4-wire SPI compatible serial interface. Control information is written to the
2
AMIS-53000 registers or read from the AMIS-53000 registers using either a 3-wire serial interface or a 2-wire I C compatible serial
interface.
Once the AMIS-53000 configuration registers have data written to them for various operational modes such as, TX, RX, Sniff or other,
placing the AMIS-53000 into one of these modes is accomplished through a single write to the command register.
TX/RX Data Interface
The transmit or receive data interface of the AMIS-53000 can be programmed to be either a proprietary 3-wire serial interface or a
4-wire SPI compatible serial bus. The data interface can be set up to do either data transfers into a buffer in the AMIS-53000 or
streaming data (data is transmitted as it is received by the AMIS-53000 or data is sent to the host/controller as it is recovered in the
AMIS-53000 receiver). When using the buffered data mode, the AMIS-53000 can be the master or slave, but it must be the master to
do streaming data.
Control Interface
Once the AMIS-53000 is first powered on, an external host/controller sets the type of interface to the AMIS-53000 (3-wire or I2C) by
simply writing to the AMIS-53000 with the desire protocol. The AMIS-53000 will continue to use that interface protocol until power is
removed from the AMIS-53000. The AMIS-53000 is always a slave device for the control interface.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
7
AMIS-53000 Frequency Agile Transceiver
Data Sheet
2.0 Operational Specifications
2.1 Absolute Maximum Ratings
Table 1: Absolute Maximum Ratings
Symbol
Parameter
Min.
Max.
Units
V
Notes
Vdd
DC Supply Voltage
-0.3
3.6
Vin
Input Pin Voltage
-0.3
Vdd+0.3
V
Iin
Input Pin Current
-10.0
10.0
mA
Tstrg
Storage Temperature
-55
150
C
SSOP
Tlead
Lead Temperature
300
C
10 SEC
ESDHBM
Human Body Model
2
kV
ESDCDM
Charged-Device Model
750
V
ESDMM
Machine Model
200
V
25C
2.2 Recommended Operating Conditions
Table 2: Operating Conditions
Symbol
Parameter
Vdd
Min.
Max.
Units
2.2
3.3
V
DC Supply
Notes
Idd
Dynamic Current
70
mA
(1) Continuous TX
Idds
Standby Current (off current)
2
uA
(2)
Vss
Ground
0.0
0.0
V
Ta
Ambient Temperature
-40
85
C
Notes:
1. Dynamic current is with the transmitter enabled at maximum output power + 15dBm in FSK mode at 928MHz.
2. Standby current is with all analog cells in power down. Other logic powered up with no clocks running. All outputs unloaded and inputs tied high or low.
No floating inputs.
2.2.1. Parametric Voltage and Current Levels
(Testing for the below currents assumes a static test setup with measurements performed while static data is applied to the device.)
2.2.1.1.
Inputs
Table 3: Pin Input Parameters
Pin
Vil
Iil
(1)
Vih
Iih
(1)
Notes
(2)
Min.
(V)
Max.
(V)
Min.
(V)
Max.
(V)
Min.
uA
0.0
Max.
uA
1.0
Min.
uA
-1.0
Max.
uA
0.0
DISU
0.0
0.3
0.8
1.0
0.0
1.0
-30
-90
CMOS with pull up Schmitt
DISC
0.0
0.3
0.8
1.0
0.0
1.0
-1.0
0.0
CMOS Schmitt
AI
Analog input
Notes:
1. Iil and Iih are tested at Vdd = VDDmax volts. Not tested at less than room temperature.
2. PU = Pull up, PD = Pull down, SC = Schmitt, SU = Schmitt & Pull up and SD = Schmitt and Pull down.
3. CMOS values are 'Vin * VDD' and TTL values are absolute voltages.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
8
AMIS-53000 Frequency Agile Transceiver
2.2.1.2.
Outputs
Table 4: Pin Output Parameters
Vol
Voh
Pin
(1)
(2)
Min.
Max.
Min.
Max.
(V)
(V)
(V)
(V)
AO
DO
Data Sheet
0
0.4
Vdd-.4
Iol
(1,3)
Min.
Max.
mA
mA
Ioh
(2,3)
Min.
mA
Notes
Max.
mA
Analog outputs
2
-2
CMOS
Notes:
1. Vol, Iol are tested at Vdd = VDDmin volts unless otherwise stated.
2. Voh, Ioh are tested at Vdd = VDDmin volts unless otherwise stated.
3. Polarity on currents indicates direction of current: (+) for sinking and (-) for sourcing.
2.2.1.3.
I/O Pins
Table 5: I/O Pin Parameters
Pin
Vil
V
Min.
Vil
V
Max.
Vih
V
Min.
Vih
V
Max.
Vol
V
(1)
Vol
V
Max.
(1)
Voh
V
Min.
(2)
Voh
V
(2)
Iol
mA
Min.
(1)
Ioh
mA
Min.
(2)
Iozl
uA
Max.
(3)
Iozh
uA
Max.
(3)
Notes
0
0.3
0.8
1
0
0.4
Vdd-.4
Vdd
2
-2
1
-1
Schmitt
AIO
DIO
Notes:
1. Vol, Iol are tested at Vdd = 3.1 volts.
2. Voh, Ioh are tested at Vdd = 3.1 volts.
3. Ioz is tested with Vdd = 3.5 volts.
*** Leakage on I/O pins is typically checked for +/- 10 microamps with the output device turned off and no PU or PD device present.
2.3 Operational Specifications
Table 6: Operational Specifications
Parameter
Min.
Typ.
Max.
Units
Comment
Receiver
Frequency Range
Sensitivity
Noise Figure
300
928
MHz
-107
-114
dBm
@ 10kHz data rate (FSK/GFSK modulation)
-104
-111
dBm
@ 10kHz data rate (OOK modulation)
9.0
dB
6.0
7.8
IIP2
+60
dBm
Dual tone test using RSSI
IIP3
+5
dBm
Dual tone test using RSSI
Image Rejection
30
Input Impedance
RSSI Gain
14
IIN
ISB
40
50
Modulated desired, single tone interferer
Ω
@ 900MHz series equivalent
72-j62
Ω
@ 433MHz series equivalent
16
18
8
Full
Shutdown
Crystal
Mode
dB
15-j35
mV/dB
mA
Receiver current consumption at 900MHz
2
uA
Standby current (no clocks enabled)
2
mA
System clock output enabled (6MHz)
Ton
100
us
Standby to receiver on time
TRX_TX/ TTX_RX
100
us
Transition time from RX to TX or TX to RX
LAN
Input Trim
1.2
4
pF
Internal capacitor range for the receiver input
Output Trim
0.32
0.912
pF
Internal capacitor range for the output of the LNA in the receiver
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
9
AMIS-53000 Frequency Agile Transceiver
Table 6: Operational Specifications (Continued)
Parameter
Min.
Typ.
Max.
Units
Comment
Transmitter
Frequency Range
300
928
MHz
Ton
100
us
Standby to transmitter on time
TTX_RX
100
us
Transition time from TX to RX
OOK On/Off Ratio
FSK Frequency
Separation
60
dB
CW Output Power
0
200
kHz
Allowable transmit/receive peak deviation
-20
15
dBm
Range of output power in the high power mode
-25
0
dBm
Range of output power in the low power mode
dBc
With complete matching network
Internal capacitor range for the PA adjustable trim
PHARMONICS
35
TX PA
Output Cap.
2
7.5
pF
Output Switch R
5
18
Ω
-35
dBc
On/Off Ratio
60
Output Harmonics
dB
With typical 50Ω matching circuits
Operating Current
50
68
mA
15dBm CW
Operating Current
High
MAX
Power
Power
Low
Power
High
MAX
Power
Power
Low
Power
Crystal Oscillator
12
24
mA
0dBm CW
14
16.5
17
dBm
-1
4.5
5.7
dBm
15.8
16.5
17
dBm
3
4
5
dBm
Matching network for 50Ω 928MHz high
Matching network for 50Ω 433MHz high
Center Frequency
24
Tolerance
20
MHz
Trimmed
ppm
Required crystal tolerance
Startup Time
50
100
us
Quick Start enabled
Startup Time
2
5
ms
Quick Start disabled
45
pF
Internal trim capacitor (self calibration sets)
175
fF
Trim Cap
Trim Resolution
0
145
160
Idd
800
uA
Normal operation
Idd
1.5
mA
During Quick Start
10kHz Oscillator
Output Frequency
9.8
10
10.2
kHz
After trimming
Operating Current
300
375
450
nA
After trimming
Duty Cycle
50
%
ADC
Resolution
FSR
8
Vss
Ci
Vref
Reference Offset
fclk
Full scale input range
1
pF
Input capacitance
V
Internal voltage reference
1
0.01
10
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
V
2.0
Conversion Rate
Conversion Time
Bits
Vref
%FSR
2
MHz
200
KSPS
Clock frequency
Clock rate = 2MHz
Tclk
10
Data Sheet
AMIS-53000 Frequency Agile Transceiver
Table 6: Operational Specifications (Continued)
Parameter
Min.
Typ.
Max.
Units
Comment
Data Filter
3dB Down Point
110
120
130
%FDATA
AM data filter bandwidth (relative to associated defined data rates)
Output Voltage
0.93
0.97
1.01
V
At 27 C
Voltage Range
0.61
0.97
1.4
V
Output
Temperature Sensor
Slope
o
-5.24
mv/ C
o
dV/dT
RSSI Buffer
Input Range
Vdd
V
Operating Current
135
0
185
250
uA
Unity Gain-BW
615
1000
1700
kHz
100kΩ/100pF load
PLL
Reference Input
Frequency
Resolution
VCO Gain
Constant
12
MHz
Transmit mode (24MHz external crystal)
16
MHz
Receive mode (24MHz external crystal)
91.55
Hz
9.62
12
14.4
MHz/V
25.6
32
38.4
MHz/V
us
Frequency step size
@ 900MHz, although layout PCB
@ 400MHz
parasitics and component
@ 900MHz
placement will change this value
Internal loop filter
Settling Time
100
Phase Noise
-90
-80
dBc/Hz
Internal loop filter @ 10kHz offset
Phase Noise
Max Spurious
Level
POR
-120
-110
dBc/Hz
Internal loop filter @ 3MHz offset
-70
-50
dBc
Delay Time
28
43
60
ms
Brown-out Trip
1.2
1.6
1.8
V
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
Internal loop filter
11
Data Sheet
AMIS-53000 Frequency Agile Transceiver
Data Sheet
3.0 Block Diagrams
3.1 AMIS-53000 Overall Block Diagram
Figure 1: AMIS-53000 Block Diagram
3.2 Package
3.2.1. Pin Definition
Table 7: Pin Definitions
Pin#
-001
-002
Pin Type
Description
LNAvdd
Power
A DC short (inductor) is connected to VDD from this pin
1
LNAvdd
2
RFin
RFin
Analog Input
The RF input to the receiver circuits
3
RFvss
RFvss
Ground
Ground for the RF circuits
4
RFout
RFout
Analog Output
5
RFpwr
RFpwr
Analog Output
6
Avdd
Avdd
Power
RF transmit output
Variable DC voltage output to power the RF transmitter (requires a DC short {inductor}
connection to Rfout)
Vdd power for the analog circuits
7
ADC1
ADC1
Analog Input
Input to the analog to digital conversion circuit
8
ADC2
ADC2
Analog Input
Input to the analog to digital conversion circuit
9
RSSI
RSSI
Analog IO
Analog voltage related to the strength of the received RF
10
PEAK
PEAK
Analog
Analog voltage for external auto-slice capacitor
11
Avss
Avss
Ground
Ground for the analog circuits
12
XTAL2
XTAL2
Analog
Connection to an external crystal
13
XTAL1
XTAL1
Analog
Connection to an external crystal
14
INT
INT
Digital Output
Interrupt to external controller
15
Dopt
Dopt
Digital Input
Optional data pin for the 4-wire data interface mode
16
Dssn
Dssn
Digital IO
Active low select line for the data interface
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
12
AMIS-53000 Frequency Agile Transceiver
Table 7: Pin Definitions (Continued)
Pin#
-001
-002
Pin Type
Data Sheet
Description
17
Drxtx
Drxtx
Digital IO
Serial data input (transmit) or output (received)
18
Dclk
Dclk
Digital IO
Recovered clock output (data interface clock)
19
SYSclk
SYSclk
Digital Output
System clock output
20
Dvss
Dvss
Ground
Ground for the digital circuits
21
Dvdd
Dvdd
Power
22
CoreReg
SSN
Digital
23
SCLK
SCLK
Digital
Vdd power for the digital circuits
-001 (control and status for the serial data interface)
-002 (decoupling capacitor pin for the internal regulator)
Bi-directional clock for the 2-wire serial interface
24
SDATA
SDATA
Digital
Bi-directional data for the 2-wire serial interface
25
xBURST
xBURST
Digital Input
Active low input interrupt that will immediately cause a Burst transmission
26
LOOPout
LOOPout
Analog
Output to the optional external loop filter
27
LOOPin
LOOPin
Analog
Input from the optional external loop filter
28
LOvss
LOvss
Ground
Ground for the local oscillator circuits
29
LOn
LOn
Analog
Negative side of the VCO tank
30
LOp
LOp
Analog
Positive side of the VCO tank
31
LOvdd
LOvdd
Power
Vdd for the local oscillator circuits
32
RFvdd
RFvdd
Power
Vdd power for the RF circuits
3.2.2. Block Diagram/Pin Definition
Figure 2: Block Diagram/Pin Definition *
* Not actual package markings. Please see marking format in 3.2.3.3.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
13
AMIS-53000 Frequency Agile Transceiver
3.2.3. Physical Characteristics
3.2.3.1.
Package Type
32 pin LQFP
3.2.3.2.
Package Dimensions
Table 8: AMIS-53000 LQFP Package Dimensions
Symbol
Min. Nom. Max.
Units
Thickness
-
D
9.00 BSC
-
1.60
mm
D1
7.00 BSC
mm
E
9.00 BSC
mm
E1
7.00 BSC
mm
e
0.80 BSC
mm
mm
Figure 3: Package
3.2.3.3.
Package Marking Format
(AMIS Logo)
AMIS53000a
19608-bbb
XXXXYZZ
Where:
a is the market application
bbb is the AMIS device version
XXXXYZZ is the date and tractability code**** is the country of origin (found on underside of chip).
The year in which the mask work was first fixed in a semiconductor chip product may also appear.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
14
Data Sheet
AMIS-53000 Frequency Agile Transceiver
4.0 Acronyms
The following acronyms are used in this document.
AM
Amplitude Modulated signal
ASIC
Integrated circuit designed for a single customer requirement
ASK
Amplitude Shift Key
ASSP
A custom integrated circuit, that may be used in general designs
ASTRIC AMI Semiconductor’s family of wireless products
CCA
Clear Channel Assessment
CDR
Clock and Data Recovery, data is recovered from the received signal using a synchronous clock
CRC
Cyclic Redundancy Checking; data error checking
CW
Continuous Wave, a single frequency or modulated signal carrier
DAC
Digital to Analog Conversion
dB
Decibels; a logarithmic measure of signal level
dBm
Logarithmic measure of signal level above a milli-watt
DFFT
Digital or Discrete Fast Fourier Transform
DPLL
Digital Phase Locked Loop circuit to create a precise frequency
EE
Electrical Erasable Memory
FFT
Fast Fourier Transform; transform between time and frequency
FM
Frequency Modulated signal
FSK
Frequency Shift Key
GFSK
Gaussian Data Waveform Modulated signal
IF
Intermediate Frequency
kbps
Data rate in thousand bits per second
kHz
Frequency in kilohertz per second
LO
Local Oscillator frequency; used to convert signals between RF frequency and IF frequency
LOP
Byte indicating the length of a packet
MHz
Frequency in megahertz
MICS
Medical Implantable Communication System
mV
Milli-volts
OOK
On/Off method of creating an amplitude modulated signal
OTA
Transconductance Amplifier
PLL
Phase Locked Loop circuit to create a precise frequency
POR
Power-on-Reset is a threshold circuit for limiting operation at low voltages
RF
Radio Frequency
RSSI
Received Signal Strength Indication; measurement of RF signal strength
SOF
Byte indicating start of packet in data protocol
VCO
Voltage controlled variable frequency oscillator
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
15
Data Sheet
AMIS-53000 Frequency Agile Transceiver
Data Sheet
5.0 Hardware Description
5.1 Frequency
The AMIS-53000 uses an internal VCO, PLL and trim capacitors with an external oscillator crystal to generate the RF frequencies for
both TX and RX. The external crystal is a parallel resonant mode crystal with required loading capacitors. The AMIS-53000 contains
internal load capacitors, typically sufficient for use with the suggested 24MHz. It is suggested that a 24MHz with 20ppm tolerance be
used with the AMIS-53000.
Figure 4: External Crystal Circuit
The internal VCO requires an external parallel LC to set the frequency for RX or TX. There is an internal capacitance that needs to be
considered when selecting the values of the inductor and capacitor. The AMIS-53000 is sensitive to the positioning of the LC
components in the layout of the PCB. The traces to the LC need to be as symmetrical as is possible. The location of the LC needs to
be as close to the AMIS-53000 pins as is practical. A simple layout change to these parameters can mean that the AMIS-53000 VCO
frequency will change causing a need to change the values of the inductor, capacitor and/or the values in the registers controlling the
RF frequency. The value of the inductor and/or the capacitor may need to be adjusted to allow the AMIS-53000 to calibrate the PLL for
a given frequency of operation. The layout of the printed circuit board for the inductor and capacitor should route traces connecting
other components away from the inductor and capacitor pads.
The VCO in the AMIS-53000 is a differential negative resistance oscillator (DNRO), commonly found in the literature. It uses an internal
voltage variable capacitor (varactor) in combination with an external L and C to provide the desired frequency. The output frequency is
found simply by:
Where: Ltot and Ctot are the total inductance and capacitance respectively at the VCO pins. This includes the internal capacitance of
approximately 2pF.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
16
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Figure 5: VCO External LC Circuit
The AMIS-53000 has an internal loop filter to work with the PLL in creating the frequency of the device. There is an option to use an
external loop filter.
Table 9: Internal Loop Parameters
Filter
Component
Value
R1
Second Order
Additional Pole
60
C1
64
pF
C2
3
pF
R
110
kΩ
C
1
pF
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
Units
Comments
kΩ
17
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Figure 6: Optional External Loop Filter Circuit
An internal 10kHz oscillator provides timing for functions; Sniff Mode, Burst transmit and housekeeping, when the AMIS-53000 is in its
lowest power mode (idle/standby). This oscillator requires no external components. The 10kHz oscillator’s internal trim capacitor is
trimmed by 8 bits of trim control in a self calibration. Once the trim is set, the oscillator frequency will be accurate to within two percent
over specified voltages and temperatures.
5.2 Receiver
The AMIS-53000 has a single channel receiver. The LNA for the receiver input requires a DC connection to ground on the input (must
not be an RF ground connection). The LNA for the receiver input requires a DC connection to RFVDD on the output. These
connections are supplied through inductors becoming part of the matching circuit for the receiver input.
Figure 7: Receiver Input Matching Circuit
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
18
AMIS-53000 Frequency Agile Transceiver
Data Sheet
5.2.1. Receiver Low Noise Amplifier (LNA)
The receiver input of the AMIS-53000 is a single ended input and single ended output device. The input is matched to 50Ω using an
external matching network, which provides a DC path to ground for biasing the receiver’s LNA. The output of the LNA is tuned to the
desired operating frequency using an external inductor and on-chip capacitor. The inductor is also provides the LNA with DC supply
voltage. On-chip tuning capacitors are binary weighted and digitally controlled.
The internal input capacitance is 1.2pF to 4pF. With this capacitance set to the mid value (register set to 0X80), the impedance of the
receiver is shown in Figure 8. The internal output capacitance is 0.32pF to 0.912pF.
Figure 8: RX Input Impedance
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
19
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Figure 9: Receiver LNA Output Inductor Selection
5.2.2. IF Filter
A passive poly-phase filter and active filtering are used in the AMIS-53000 for frequency selectivity and rejection of the image
frequency. It is designed to provide an optimal image rejection of 50dB at 500kHz.
5.2.3. Data Filter
The OOK low-pass data filter is used for additional post-detection signal filtering in accordance with the OOK signal data rate (1.2, 1.8,
2.4, 4.8, 7.2, 9.6, 14.4, 19.2kHz). The RSSI buffer is used to drive the RSSI signal off chip for external monitoring, and can also be
internally configured for monitoring other signals such as the analog temp sense voltage or bandgap voltage.
5.3 Transmitter
The AMIS-53000 transmitter is a two-stage output amplifier. When both stages are selected, the highest output power at frequencies
from 300MHz to 928MHz is +15dBm. When only one stage is used, the AMIS-53000 can output up to 0dBm with better power
efficiency than when outputting the same power level with both stages. The voltage output level on the RFPWR pin controls the RF
output power level of the AMIS-53000. A DC connection must be made between the RFOUT pin and the RFPWR pin. The non-linear
output of the AMIS-53000 may require external components to match to a load and to reduce the spurious harmonics.
The output impedance of the AMIS-53000 can be matched to the impedance of an external load, using the spreadsheet AMIS53RFMATCH.xls provided by AMIS. This spreadsheet is explained in the application note, AMIS-52X00 Antenna Impedance Matching
Considerations. The goal of the transmit output matching with this spreadsheet is to optimize the output power while reducing the
harmonic power.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
20
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Figure 10: Transmitter Output Matching Circuit
5.4 Single Antenna Option
The AMIS-53000 is designed such that when the transmitter is off or the receiver is off, the pins are grounded. This provides a known
impedance for the off port (transmit or receive) in combining the receiver and the transmitter to a single antenna.
Figure 11: Single Antenna Port T/R Matching Circuit
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
21
AMIS-53000 Frequency Agile Transceiver
Data Sheet
5.5 Peak
The AMIS-53000 has three modes for slicing the received signal to recover the data. One method is to set a threshold value that is
fixed and to which the receiver compares the recovered signal. The other two methods have the AMIS-53000 automatically setting a
threshold level to which the receiver compares the recovered signal. Both of these automatic threshold methods require an external
capacitor on the PEAK pin to operate.
In the averaging method, the AMIS-53000 simply adds a low pass filter with a cutoff frequency set below the data rate filter setting.
This second filter extracts an average RSSI level as the data slice threshold. The capacitor on the PEAK pin sets the time constant
(corner frequency) for this filter. A typical capacitor value would allow the average level to settle to 95 percent of the RSSI level in 2 bit
intervals (remember that Manchester encoding may have transitions twice the data rate). The average threshold method will have
chatter before a signal is received and after the signal ends which the external host/controller must be able to handle.
In the peak method the AMIS-53000 uses a peak detector to find the maximum input signal level and then sets the threshold 6dB lower
than that level. The external peak capacitor is used to bleed or discharge the peak voltage in the circuit. The voltage swing on the
-3
RSSI for a typical 12dB signal to noise ratio at 10 BER is 240mV. The capacitor value should not change the voltage by more than
this 240mV during a string of zeros. The value is dependent on the number of zeros that are allowed in the chosen data protocol, NRZ
or Manchester encoded.
Figure 12: Peak Capacitance Circuit
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
22
AMIS-53000 Frequency Agile Transceiver
Data Sheet
5.6 ADC
The ADC is a successive approximation analog to digital converter, using an internal 8 bit DAC as the reference. The ADC data for the
selected input channel(s) will be stored in the associated register, allowing for external access to the conversion data through the serial
interface. Conversion speed is register selectable up to 128kS/s. Commands in the control register allow for single or continuous
operation of the ADC.
A voltage regulator generates the 2.0V reference for the ADC and DAC based upon an internal bandgap voltage source. The ADC has
six inputs, two of which are available to the designer for use in their application.
5.7 Control Interface Serial Bus
The AMIS-53000 uses a 3-wire or 2-wire I2C interface to communicate with the AMIS-53000 internal registers. The AMIS-53000 will
automatically determine which interface to use by determining the states of the three lines; SDATA, SCLK and SSN (the interface is set
when the external host/controller writes the first data to the AMIS-53000). Once the AMIS-53000 has determined the type of interface,
it will continue with that configuration until power is removed from the part or the part is reset.
2
2
2
I C: If SSN is high and an I C start bit is detected, I C mode is enabled.
SPI: If SSN is low, and a negative edge on SCLK detected, SPI mode is enabled.
The AMIS-53000 is designed to conform to the Philip Semiconductor I2C standard with the AMIS-53000 as the slave device.
Figure 13: I2C Serial Bus Connections
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
23
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Figure 14: 3-Wire Control Bus Connections
5.8 TX/RX Data Interface Serial Bus
The AMIS-53000 uses a 3-wire or 4-wire SPI serial data interface to transfer data between the external host controller and the
AMIS-53000. The interface is selected by writing to a register in the AMIS-53000. The DOPT line is undefined in the 3-wire interface.
The 4-wire interface of the AMIS-53000 is designed to be compatible with the definition of a standard SPI interface. The AMIS-53000
can be a slave or master device. The status of the AMIS-53000, master or slave, and the interface mode, read or write, determine the
definition of the DRXTX and DOPT pin’s as outputs or inputs.
Figure 15: SPI Compatible Serial Data Interface
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
24
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Figure 16: 3-Wire Serial Data Interface
5.9 System Clock
The system clock can provide a clock to the external host controller. The clock can be divided down from the 24MHz crystal frequency
of the AMIS-53000. When a design desires to use the system clock as the clock to an external host/controller, the system clock can be
output under the following:
•
•
•
Will be output in RX or TX, unless the output is off in general options B (Bit 1:0).
The output will start back up in idle mode after a packet is received.
The output will start back up in housekeeping if wake up external host/controller is enabled in housekeeping configuration
(Bit 6).
Table 10: System Clock Control
Mode
Control
0X0D General Options B
Bits
Outputs
1:0
Frequency: 12, 6, 3MHz or off
2:1
POR state: standby, idle, RX, TX
0
Output in standby
4:3
Clock cycles before stop
Comments
RX
TX
Standby
General Options A
Idle
Idle Config
5.10 Power and Grounds
The AMIS-53000 has four different power inputs and two different grounds. This allows the design of the AMIS-53000 in an application
to separate RF power from the analog and digital power. The same applies to the grounds, where a separate ground plane for the RF
grounds can reduce the amount of noise induced into the sensitive RF circuits.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
25
AMIS-53000 Frequency Agile Transceiver
Data Sheet
5.11 Design Suggestions
The following schematic and layout suggests at least one way to create a printed circuit board for applications using the AMIS-53000.
Figure 17: Typical Design Schematic
Figure 18: Typical Design Layout Suggestion
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
26
AMIS-53000 Frequency Agile Transceiver
Figure 19: Minimum Design Schematic
Figure 20: Minimum Design Layout Suggestion
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
27
Data Sheet
AMIS-53000 Frequency Agile Transceiver
Data Sheet
6.0 User’s Guide
This user’s guide divides the control register description of the AMIS-53000 into functional areas; command register flow diagrams,
frequency generation, receiver, transmitter, idle, data/control interfaces, Burst transmit, and MICS features.
6.1 Control Serial Interface Bus Description
Table 11: Control Interface Physical Configuration
Interface
2
Function
Clock
Pin
Data
Source
Output
Input
Select
AMIS-53000
IC
Control
SCLK
Master
SDATA
SDATA
None
Slave only
3-Wire
Control
SCLK
Master
SDATA
SDATA
SSN
Slave only
The AMIS-53000 employs two different control interfaces. Communication with the AMIS-53000 control registers is through either a
3-wire bus or through a 2-wire (with third line for control/status) I2C compatible bus. The state of the control bus is detected by the
2
2
AMIS-53000 at the first communication, I C or 3-wire, and is set in that function (3-wire or I C) as long as power remains applied to the
part.
3-wire control communication bus
2
I C control communication bus
AMIS-53000 is always the slave
6.1.1. Control Interface Protocol
The AMIS-53000 control interface allows an external controller to write instructions to the registers of the AMIS-53000 and control the
functions of the AMIS-53000. The external controller can also read the registers and status of the AMIS-53000. The control interface
2
can be configured as a slave device in either a 2-wire I C interface bus or a 3-wire serial interface.
Figure 21: Control I2C Protocol Format
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
28
AMIS-53000 Frequency Agile Transceiver
2
Table 12: I C Addressing
Address
Description
0110100X
AMIS-53000 I C Address
01101000
AMIS-53000 Write Command
01101001
AMIS-53000 Read Command
2
Figure 22: 3-Wire Control Protocol Format
Table 13: 3-Wire Control (IN1 and IN0)
Control Word Bits
Description
IN1
IN0
0
0
Single Register Read
0
1
Single Register Write
1
0
Sequential Register Read
1
1
Sequential Register Write
I2C device address:
o 0x68 HEX for device write
o 0x69 HEX for device read
External controller can write registers
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
29
Data Sheet
AMIS-53000 Frequency Agile Transceiver
Data Sheet
External controller can read registers
External controller can issue a immediate transmit via the xBURST input
External controller can receive an interrupt (xINT) from the AMIS-53000
Setup registers descriptions:
I2C/3-wire select- First write to the interface sets the type of interface until AMIS-53000 is power cycled.
6.1.2. Serial Control Interface: Configuration
The AMIS-53000 can automatically detect the type of interface for the serial control bus. The interface pins are then given the
definitions as shown in Table 14. The detection depends on the status of the AMIS-53000 pins as shown in Figure 23.
Table 14: Control Port Pin Definitions
2
Pin Name
I C Mode
3-Wire Mode
SCLK
SCL
SCLK
SDATA
SDA
R/W controlled
SSN
Internal pull up
SSN
Figure 23: Control Interface Selection
Simply addressing the part with the desired protocol performs initial interface selection. After the first communication with the part, the
selection is locked until power is removed from the device. The internal logic for determining which protocol to use on initial power up is
as follows:
2
2
2
I C: If SSN is high and an I C start bit is detected, I C mode is enabled.
3-wire: If SSN is low, and a negative edge on SCLK detected, 3-wire mode is enabled.
The internal pull ups on SCLK and SDATA can also be disabled for I2C applications using external pull ups.
Table 15: Control Interface Pull Up Control
Mode
SCLK, SDATA Pull Ups
SSN Pin Configuration
IC
Controlled by bit 3 of the general
options A register
Not used (internal pull up)
3-wire
Controlled by bit 3 of the general
options A register
SSN: normal mode
2
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
30
AMIS-53000 Frequency Agile Transceiver
6.1.3. 3-Wire Interface Mode
The AMIS-53000 is always the slave device.
Figure 24: Master/Slave for Bi-Directional 3-Wire Mode
Figure 24 illustrates the connections between the master SPI port and the slave 3-wire port in the AMIS-53000.
Figure 25: Single Control Register Read/Write Using the 3-Wire Interface
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
31
Data Sheet
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Figure 25 shows a single read or single write control data transfer. The operation starts with SSN transitioning low to indicate a start of
transfer. The first two bits transferred are the instruction for the slave interface of the AMIS-53000, IN1 and IN0. Following the
instruction are the six address bits to specify which address to read or write from. If the instruction is to write a register, the data to be
written to address location A<5:0> is specified with the next 8 bits, D<7:0>. If the operation is a read, the slave output buffer is enabled
at the end of the address bits, and the data bits D<7:0> are buffered out of the part MSB first.
For single read/write, the SSN line can remain active between successive read and write operations.
Figure 26: Sequential Control Register Read/Write Using the 3-Wire Interface
Figure 26 is a diagram for sequential reads or sequential writes for 3-wire control data transfer. The format of the instruction and
address is identical to that for a single read/write operation, with the address corresponding to the first register location to read or write.
The first 8 bits of data transferred correspond to the address selected. The address is internally incremented after each data byte
transferred. This task is most useful for writing to or reading from variables spanning over multiple address locations such as the
fractional PLL word (registers 03-05).
The SSN line must be de-asserted at the completion of a sequential read/write in order for the slave SPI controller to correctly interpret
the next 8 bits as a command and not data.
2
6.1.4. I C Interface
The I2C interface for the AMIS-53000 is compatible with the Philip Semiconductor I2C standard, with the AMIS-53000 as the slave
device.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
32
AMIS-53000 Frequency Agile Transceiver
6.1.4.1.
Data Sheet
I2C Device Addressing
A control byte is the first byte received following the start condition from the master device. The control byte consists of a 7-bits for the
device address, and 1-bit for a read or write command. For the AMIS-53000, the device address is ‘0110100’ binary. The last bit of the
control byte defines the operation to be performed. When set to ‘1’, a read operation is selected. When set to ‘0’, a write operation is
selected. Following the start condition, the AMIS-53000 monitors the SDA bus checking the device type identifier being transmitted.
Upon receiving its device address, the AMIS-53000 outputs an acknowledge signal on the SDA line. Depending on the state of the R/W
bit, the AMIS-53000 will select a read or write operation.
6.1.4.2.
Single Register Write
Figure 27: Single Control Data Read/Write with the I2C Interface
The master device issues the start condition, then issues the device address, and then issues the single R/W bit, a logic low state. This
indicates to the addressed slave receiver that a byte with a register address will follow after the slave has generated an acknowledge bit
during the ninth clock cycle. Therefore, the next byte transmitted by the master is the register address to be written with data. After
receiving another acknowledge signal from the AMIS-53000, the master device will transmit the data word to be written, and the
AMIS-53000 will acknowledge again. The write cycle ends with the master generating a stop condition.
A similar approach is used to read a register value. The master device issues the start condition, then issues the device address, and
then issues the single R/W bit, a logic low state. This indicates to the addressed slave receiver that a byte with a register address will
follow after the slave has generated an acknowledge bit during the ninth clock cycle. Therefore, the next byte transmitted by the master
is the register address to be read. After receiving another acknowledge signal from the AMIS-53000, the master device will immediately
follow with another start sequence, however, the R/W bit is now set high telling the slave device that the master wants the contents of
the register (addressed with the write command) to be placed on the SDA bus line. After 8 bits of data are read by the master, the
master does not acknowledge but sends the stop sequence.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
33
AMIS-53000 Frequency Agile Transceiver
6.1.4.3.
Data Sheet
Sequential Register Write
Figure 28: Sequential Control Data Read/Write with the I2C Interface
When setting the AMIS-53000 up for an application it sometimes is nice to write data to a number of registers one after the other. The
write control byte, register address and first data byte are transmitted to the AMIS-53000 in the same way as in a byte write. However,
instead of generating a stop condition, the master can continue to write register locations. Upon receipt of each word, the address is
internally incremented by ‘1’. If the master should transmit more words than the AMIS-53000 has address locations, the address will roll
over.
It is a similar approach to read a register value. The write control byte and register address are transmitted to the AMIS-53000 in the
same way as in a byte write. After receiving another acknowledge signal from the AMIS-53000, the master device will immediately
follow with another start sequence, however, the R/W bit is now set high telling the slave device that the master wants the contents of
the register (addressed with the write command) to be placed on the SDA bus line. After the 8 bits are read by the master, the master
acknowledges the reception. The AMIS-53000 will increment the register address and continue to output register values. After the last
register value is received by the master, the master does not respond with an acknowledge but sends the stop sequence.
6.1.4.4.
Current Address Read
The internal address counter maintains the last address addressed, incremented by ‘1’. If the last instruction received was to access
register N, the current address read operation will read the contents from register N+1. The timing for the current address read is to
send a start bit followed by the 7-bit device address, with the R/W bit set to one. The slave will acknowledge, after which the 8-bit
register contents will be transmitted. The master does not acknowledge the transmission, but does generate a stop bit.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
34
AMIS-53000 Frequency Agile Transceiver
6.1.4.5.
Data Sheet
Interface Options
2
Table 16: I C Address Auto Increment
Register
Number (HEX)
Name
0X0C
General Options A
0X0D
General Options B
Bits
Function
3
Disable the internal pull up resistors on SDATA and SSN lines
5,4
Select a clock rate for the interface when the AMIS-53000 is master
3
Disable auto increment for I C control interface register addressing
2
Additional interface options give the AMIS-53000 the flexibility to tailor the interface to specific requirements. These options are
available in the interface options register, and can be stored into EE at board assembly to best suit the application.
6.1.4.6.
Pull Up Disable
The AMIS-53000 includes built in pull up resistors for use with the I2C operation to reduce the overall system component count. The
pull ups are asserted at POR until mode selection occurs. If mode is determined to be 3-wire, the pull ups are removed. If mode is
2
determined to be I C, this option bit determines whether the pull ups are to be removed.
6.2 Command Register
The AMIS-53000 contains a single 8-bit register that allows single writes to the register to place the AMIS-53000 into a desired mode.
It is very important to remember that all registers associated with that mode must be preprogrammed for the single write to this register
to operate correctly.
The command register allows the user application to issue a single register write to the AMIS-53000 to initiate the function listed in
Table 17. When the function is started, the AMIS-53000 uses the register values associated with the function selected as the
parameters of the function. These register values will be the default values or the values the user application has written to the
registers before the function is called out in the command register.
Table 17: Command - 0X00 [0]
Bit
Command
[7:4]
0000
[7:6]
01
11
[3:0]
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1111
[5:0]
XXXXXX
100000
XXXXXX
100000
Standby
Receive
Transmit
Idle
Idle Return
Write EE
Read EE
Calibrate QS Osc
Calibrate RC
Calibrate PLL
Calibrate LNA
ROM2Regs
Global Reset
Single ADC
Conversion
Continuous ADC
Conversions
Comment
Put the part into standby
Put the part into receive mode
Put the part into transmit mode
Put the part into idle mode
Use to return to idle after interrupt for HK or receive during sniff
Write the content of the working registers into EE
Read the contents of the EE
Calibrates the Quick Start oscillator
Calibrates the 10kHz RC oscillator
Calibrates the PLL
Calibrates the LNA matching
Write the content of the ROM into the shadow registers
Resets the part completely
Do an ADC one time on the channel selected loop filter output
Do an ADC on the channel selected continuously loop filter output
Standby is both a state for the transceiver, and a command given to the transceiver. The actual operation of standby mode can be
either a low-power mode where all internal circuitry of the AMIS-53000 except for the interface will be disabled, or a clock-only mode
where the crystal oscillator will be enabled to continue providing a system clock for an external microprocessor. A bit available in the
general options A register allows selection of power-down or clock-only operation in standby mode.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
35
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Many of the instructions for the part are finite in duration and the end point of the task is controlled by the AMIS-53000, such as the
calibration instructions. For these instructions, the AMIS-53000 will return to its standby mode at the completion of the task. The user
may poll the Status/Flag 1 register busy bit to determine the completion of the calibration instruction. Other instructions such as receive
or transmit are indefinite in length and user controlled. To return to the standby state, the AMIS-53000 waits for the standby instruction
to end receive or transmit, at which point the transceiver will return to its standby state.
Note that there are two low-power modes for the AMIS-53000; standby and idle.
Standby allows the SYSCLK output
Idle is the very low power state without SYSCLK output
6.3 Functional Flow Diagrams
Figure 29: Receiver Flow Diagram
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
36
AMIS-53000 Frequency Agile Transceiver
Figure 30: Transmit Flow Diagram
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
37
Data Sheet
AMIS-53000 Frequency Agile Transceiver
Figure 31: Multi-Channel TX/RX
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
38
Data Sheet
AMIS-53000 Frequency Agile Transceiver
Figure 32: Idle State Flow Diagram
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
39
Data Sheet
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Figure 33: EE Flow Diagram
6.4 Frequency
The AMIS-53000 uses an internal PLL/VCO to generate the RF frequencies for both transmit and receive. Only one set of registers
needs to be programmed to generate the TX frequency and to generate the LO frequency to produce the mixing frequency for
converting the received signal to the low IF (about 500kHz). The AMIS-53000 can do a self-calibration, which will trim internal
capacitance to tune the TX and RX frequencies. The AMIS-53000 needs to run the self-calibration (must be started by the external
host/controller) at least once between startup and entering a command such as TX, RX, Sniff, etc.
6.4.1. Frequency Control
AMIS has developed an executable program (AMIS-53CALC.exe, available from AMIS, which generates the register values for the
frequency divider and fractional word to produce a given frequency. First, the AMIS-53000 must have the correct LC for the desired
frequency connected to the VCO pins. There is internal capacitance that is part of the capacitance for determining the value of the
inductor. The following equation can be used to determine the approximate value of the LC components. Remember that the VCO is
sensitive to the placement of the LC components - they should be placed as close to the AMIS-53000 as practical (even short traces
add significant parasitics) and the traces to the components should be made symmetrical.
Where: Ltot and Ctot are the total inductance and capacitance respectively at the VCO pins. This includes the internal capacitance of
approximately 2pF.
The RF PLL is a 24-bit Sigma Delta based fractional N synthesizer used to provide the LO signal for receive, and a direct RF output for
transmit.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
40
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Setup registers descriptions:
RF Divider- The RF frequency of the receiver must be configured. This is done in two steps, one is setting the RF divider and
the other is setting the fractional N word.
RF Frequency- Program the 3 register fractional N word.
Peak Deviation- When the data modulation is to be FSK, the 2 register peak deviation must also be set. The deviation should
be set to a value between ½ and 1 times the data rate.
PLL- Configure the parameters for the PLL.
Loop Filter- Configure the parameters for the loop filter.
6.4.1.1.
RF Divider
Setting the RF channel frequency is done through the RF divider register, along with the RF frequency 2, 1 and 0 registers. The RF
divider register is used to specify the integer portion of the divide value, and the RF frequency 2, 1 and 0 registers are used to specify
the fraction. The values are calculated as follows:
Where FChannel is the desired RF center frequency. The value for the RF divider register is found by,
Where integer is the value used for RF divider. The last step is to calculate the fractional value. This is done as,
Fraction is the value to be used in the RF frequency 2, 1 and 0 registers. As an example, if the desired RF frequency channel is
903.5MHz,
For this example, the RF divider register is written to 0x26, RF frequency 2 is written to 0xFE, RF frequency 1 to 0x95, and RF
frequency 0 to 0x54.This value +/- 1 is fed directly to the PLL as N0 and N1. (i.e. if 63, send 64 and 65 to the PLL)
Table 18: RF Divider - 0X05 [5]
Bit
Name
7:0
RF_divide [7:0]
Comment
00h through 0Bh: not allowed
1Ah: divide by 26
1Bh: divide by 27
----------4Ah: divide by 74
4Bh: divide by 75
4Ch through FFh: not allowed
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
41
AMIS-53000 Frequency Agile Transceiver
6.4.1.2.
Data Sheet
RF Frequency 2
Table 19: RF Frequency 2 = 0X06 [6]
Bit
Name
Comment
7:0
6.4.1.3.
RF_FREQ [23:16]
Upper 8 bits of the RF fraction
RF Frequency 1
Table 20: RF Frequency 1 - 0X07 [7]
Bit
Name
Comment
7:0
6.4.1.4.
RF_FREQ [15:8]
Center 8 bits of the RF fraction
RF Frequency 0
Table 21: RF Frequency 0 - 0X08 [8]
Bit
Name
Comment
7:0
6.4.1.5.
RF_FREQ [7:0]
Lower 8 bits of the RF fraction
Peak Deviation 1
The peak deviation for FSK transmissions is determined by the peak deviation 1 register and the peak deviation 0 register. This value
is also used inside the DFT FSK detector. Calculation of the value for the peak deviation is straightforward:
The result of this equation, converted to Hex, is entered into the peak deviation registers.
Table 22: Peak Deviation 1 - 0X09 [9]
Bit
Name
Comment
7:0
6.4.1.6.
PEAK_DEV [15:8]
Upper 8 bits of the peak deviation
Peak Deviation 0
Table 23: Peak Deviation 0 - 0X0A [10]
Bit
Name
Comment
7:0
PEAK_DEV [7:0]
Lower 8 bits of the peak deviation
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
42
AMIS-53000 Frequency Agile Transceiver
6.4.1.7.
Data Sheet
RF PLL Options
Contains general options for the setup of the RF PLL.
Table 24: RF PLL Options - 0X28 [40]
Bit Name
State
7
Kicker Calibration Status
6
Temperature
Compensation Curve
Comment
1
The kicker has been calibrated
0
The kicker has not been calibrated
1
Use the Type 1 compensation for external crystal with curves similar to Type 1 (See Figure 32)
0
Use the Type 2 compensation for external crystal with curves similar to Type 2 (See Figure 33)
1
Enable using the internal loop filter for the PLL (used for calibration)
5
4
3
Internal Loop Filter
2
Charge Pump Current
1
Ivco[1:0]
0
1
50uA
0
11
01
10
00
25uA
Ivco= 1.2mA
Ivco= 800uA
Ivco= 600uA
Ivco= auto level control
Figure 34: Typical Crystal Temperature Curve for Crystal with Type 1 Characteristics
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
43
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Figure 35: Typical Crystal Temperature Curve for Crystal with Type 2 Characteristics
6.4.1.8.
Loop Filter
Table 25: Loop Filter - 0X39 [57]
Bit
Name
7:0
LOOP_FILTER [7:0]
Comment
Internal loop filter
6.4.2. 10kHz Oscillator
The AMIS-53000 has an internal 10kHz oscillator. This oscillator is running whenever the AMIS-53000 is in standby or idle modes.
This very low power oscillator provides the clock for timing functions such as Sniff receive, Burst transmit or housekeeping. The
oscillator is trimmed in the calibration instructions.
Setup registers descriptions:
10k Oscillator Trim- The value of the calibration for the 10kHz oscillator. (See Section 6.10.1.4)**
6.4.3. System Clock
The AMIS-53000 provides a divided version of the external reference oscillator (typically 24MHz) as an output to an external
host/controller or other circuits needing a clock.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
44
AMIS-53000 Frequency Agile Transceiver
Table 26: System Clock Control
Register
Number (HEX)
Name
Bits
Data Sheet
Function
11 POR starts in TX
0X0C
2,1
General Options A
10 POR starts in RX
01 POR starts in idle
00 POR starts in standby
0
Standby mode with system clock output
11 External XTAL reference divided by 2 (12MHz)
0X0D
General Options B
1,0
10 External XTAL reference divided by 4 (6MHz)
01 External XTAL reference divided by 8 (3MHz)
00 System clock off
11 System clock continues for 1024 clock cycles
0X10
Idle Config
4,3
10 System clock continues for 512 clock cycles
01 System clock continues for 256 clock cycles
00 System clock shuts down after idle command ASAP
Setup registers descriptions:
Crystal Oscillator Trim- The value of the calibration for the 10kHz oscillator. (See Section 6.10.1.1)**
6.4.4. Quick Start
The AMIS-53000 includes the ASTRIC family patented Quick Start oscillator. This circuit uses a “kicker” to force the crystal oscillator
close to the final desired frequency. This reduces the time required for the crystal oscillator to settle to the RF frequency.
Table 27: Kicker Calibration
Register
Number (HEX)
Name
Bits
0X28
RF PLL Options
7
Function
Kicker calibration status
Setup registers descriptions:
Quick Start Trim- The value of the calibration for the kicker. (See Section 6.10.1.3)**
6.4.5. Self Calibration
The AMIS-53000 has internal trim functions for the PLL, TX PLL, RX PLL, 10kHz oscillator, and kicker (Quick Start). A self calibration
is started by writing an instruction to the command register. This self calibration needs to be done at least once after the AMIS-53000
has been powered on and before the AMIS-53000 is placed into any mode such as transmit or receive. The application should monitor
the status registers and trim value registers to determine that the calibration was successful.
Table 28: Self Calibration Command
Register
Number (HEX)
0X00
0X1B
Name
Command
Housekeeping
Config
Code
0X07
Calibrate the Quick Start (kicker)
0X08
Calibrate the 10kHz oscillator
0X09
Calibrate the PLL
0X0A
Calibrate the LNA
Bit 2
Calibrate PLL during HK
Bit 1
Calibrate 10kHz oscillator during HK
Bit 0
Calibrate kicker during HK
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
Function
45
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Setup registers descriptions:
Status- Contains the results of calibrations, instructions and activity in the AMIS-53000.
Software State- Shows the current mode of the AMIS-53000.
6.4.5.1.
Status/Flag1
The purpose of the Status1 register is to provide information back to the host on the status of the part. This register should be queried
at the completion of calibration sequences to ensure proper operation. The flags will be reset when the register is read.
CheckSum indicates whether an attempt to read or write the EE has failed due to an incorrect CheckSum.
Instruction enable indicates that the AMIS-53000 is ready to receive an instruction. This can be used to insure that the AMIS-53000
does not miss a command instruction due to the AMIS-53000 not being ready. Along with the busy flag, these status flags can police
the flow of commands to the AMIS-53000.
Table 29: Status/Flag1 - 0X01 [1]
Bit
Name
State
7
PLL xLock
6
TX PLL Cal
5
RX PLL Cal
4
RC Cal
3
Quick Start Cal
2
CheckSum
1
Instruction Enable
0
ADC Done
6.4.5.2.
1
Comment
PLL out of lock on startup (RX, TX, Sniff, Burst)
0
1
PLL calibration for transmit failed
0
1
PLL calibration for receive failed
0
1
10kHz RC oscillator calibration failed
0
1
Quick Start calibration failed
0
1
EE CheckSum failed
0
1
The AMIS-53000 is in a state of operation that can accept instructions
0
1
ADC conversion complete
0
Status/Flag2
The Status2 register provides information on the operating status of the part. The busy bit is asserted for any of the following reasons:
Calibration: The busy bit will remain high for the duration of a calibration sequence. Status2 can be repeatedly polled during
a calibration sequence to determine when it’s complete.
Read/Write EE: While the AMIS-53000 is reading from or writing to the EE, the busy bit will remain set.
Buffered RX: When in receive mode, and a valid chip ID is found, the AMIS-53000 will begin processing of this packet.
During the time the packet is being processed, the busy bit will be set high.
Buffered TX: After the command is given for transmit with the buffered packet option enabled, the busy bit will remain high
until the part has completed the actual transmission of the packet.
Housekeeping: Busy is asserted during a housekeeping cycle.
Burst TX: Busy is asserted during a Burst transmission.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
46
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Status2 also contains information on the reason an interrupt was issued to the external host. The CCA channel status bits provide
information back to the host on which channel within the MICS band is being used for communication. After a CCA enabled
transmission, these bits will be set to indicate which channel was used. For MICS enabled receivers performing multi-channel Sniff,
these bits are used to indicate the channel upon which either energy or an entire packet was found.
If CCA is enabled for operation other than MICS, bit 0 (CCA failed) is used to indicate whether or not the channel is clear. The flags will
be reset when the register is read.
Table 30: Status/Flag2 - 0X02 [2]
Bit
Name
State
CCA Channel
7:4
[3:0]
111
110
101
Interrupt Type
100
3:1
011
010
001
000
1
0
Busy
0
6.4.5.3.
Comment
Indicates channel selected during CCA
RX CRC failed
Receive energy dwell timer timed out
CCA failed
Transmit complete
Buffer data for TX
Data has been received
Housekeeping
Low battery
AMIS-53000 is busy
Software State
Displays the current mode of the AMIS-53000. This status register can be used to monitor the activity of the AMIS-53000.
Table 31: Software State - 0X3C [60]
Bit
Name
State
1111
1011
1010
1001
1000
0111
Software State
7:0
0110
0101
0100
0011
0010
0001
0000
Comment
Undetermined
Startup
Copying ROM data to registers
Calibrating LNA
Calibrating PLL
Calibrating 10kHz oscillator
Calibrating Quick Start (kicker) oscillator
Reading EE data
Writing EE data
Idle
Transmitting
Receiving
Standby
6.5 Receiver
The AMIS-53000 receiver is designed for either on/off shift key (AM) modulated signals or frequency shift key (FM) modulated signals.
The receiver includes all the circuitry to recover data from either the OOK or the FSK modulated signal carrier. The receiver operates
on fixed frequencies in the operating frequency range of 300 to 928MHz using an internal fractional N PLL to set the frequency. The
receiver can reduce power consumption using the Sniff Mode to acquire the incoming signal. The receiver can set a user defined fixed
threshold for data detection or it can form a threshold from the incoming signal for determining the presence of signal and the state of
the recovered waveform. The receiver can use a synchronous data detector to extract the data clock and the data from the incoming
signal (FSK modulation always uses this method of data detection).
OOK modulation (AM)
o Manchester encoding option
o CDR data detection option (recommended that this be used)
o Common data rates from 1.2kbps to 19.2kbps or user defined
FSK/GFSK modulation (FM)
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
47
AMIS-53000 Frequency Agile Transceiver
o
o
o
Data Sheet
Manchester encoding
FFT or PLL demodulation (depends on data rate)
Common data rates from 1.2kbps to 128kbps or user defined
The AMIS-53000 receiver is a low IF frequency single down conversion, sub-sampling, image rejection architecture with a common
AM/FM IF chain. Three demodulators are used for signal detection with additional post-detection and filtering capabilities for data
recovery.
A complex FFT demodulator is used for FSK signals with data rates > 20kbps.
A digital PLL demodulator is used for FSK signals with data rates less than 20kbps.
A logarithmic (RSSI) detector is used for OOK/ASK signals.
6.5.1. Receiver Circuit Brief Overview
Clock and Data Recovery: The AMIS-53000 can extract a synchronous clock signal from the received data. In this mode, the data in
the received signal is detected, filtered and then fed into the clock and data recovery block where additional digital filtering is performed.
The waveform is sampled using a data clock in the AMIS-53000 to synchronously recover the data. Signal sensitivity is improved and
the recovered data jitter is reduced by this method.
LO Frequency: A sub-sampling LO frequency architecture is implemented that down converts the incoming RF signal to the IF
frequency of about 500kHz. The LO frequency is produced from the internal VCO frequency. The frequency design of the LO signal
reduces the power consumption of the AMIS-53000 and simplifies the receiver, achieving reliable, quadrature LO signal generation.
IF Topology: The receiver implements a quadrature down-conversion architecture improving image rejection and creating the signals
required for the complex FFT FSK signal detection. The receiver uses this quadrature down-conversion and a combination of passive
and active poly-phase filtering to provide image suppression.
Sniff Signal Acquisition: As with earlier ASTRIC devices, the AMIS-53000 can reduce the receiver power requirements by
implementing the Sniff Mode for RF signal detection. Sniff Mode is a method using the Quick Start oscillator to quickly wake the
receiver, check for signal energy and return to sleep or start the receive function. The Quick Start can start the receiver crystal
oscillator in as little as 10 micro-seconds. Using this fast start time, the Sniff Mode can turn on the receiver, check for signal energy
and return to sleep in as little as 130 micro-seconds. More information about this Sniff Mode is in Section 6.7.2.
Table 32: Receive Command
Register
Number (HEX)
Name
Code
0X00
Command
0X01
Function
Instruction to place the AMIS-53000 into receive
(remember that all parameters for receive must be set before issuing
this command)
Setup registers descriptions:
RX Config- Options for the receiver must be set.
RF Frequency- The RF frequency of the receiver must be configured. (See Section 6.4.1.1)
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
48
AMIS-53000 Frequency Agile Transceiver
6.5.1.1.
Data Sheet
RX Configuration
Figure 36: Receiver Timing Chart
Table 33: Receiver Timing
Symbol
Timing
Min.
TPRE
1
MOD
Comments
Typ.
Max.
1
MOD
Units
D Bits
The TX preamble should be made long enough to allow the receiver to
acquire the signal
TE
0
255
D Bits
The energy dwell timer should be set long enough to allow the receiver to
2
detect the energy
TID
0
255
D Bits
The ID dwell timer should be set long enough to allow the receiver to detect
2
the chip ID or global ID
TLOP
1
255
D Bits
The length of packet will turn the receiver off after the number of data bits is
received
Default
Notes:
1. The need for a preamble and the type of preamble is determined by the data modulation selected.
2. The dwell timers need to be long enough to allow the receiver to stay active from the time it turns on due to energy and the time that the desired event occurs. However,
making this number the maximum may in the case of false energy detection or signal corruption may waste system power unnecessarily.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
49
AMIS-53000 Frequency Agile Transceiver
Data Sheet
The RX Config register is used to set options for receive mode operation.
Wake on Energy: When enabled, the CDR circuit is held in reset until the energy threshold is met. This option can be used
to make the normal receiver function to perform similar to sniff. The energy dwell timer is used to determine how long the
receiver will stay on checking for energy (With FF in the energy dwell time register, the receiver will stay on until the threshold
is met).
Gate on Energy: This option can be used in FM receive mode only, and will gate the data interface while the energy on RSSI
is below the energy threshold.
AM_FM_RX: Sets the mode of operation for receive.
Force MICS Channel: When this bit is set, the bits in Status2 used to show which channel the radio is on can be overwritten
to force a particular channel.
Table 34: RX Config - 0X0E [14]
Bit Name
State
7
RSSI Active
6
Multi Channel
5
LNA Mode[1:0]
4
3
Force MICS
Channel
2
AM_FM_RX
1
Gate on Energy
0
Wake on Energy
6.5.1.2.
1
Comment
RSSI output during RX
0
1
Sniff cycle performed at multiple pre-defined channels
0
11
10
01
00
1
0
1
No operation defined
Linear mode
High gain mode
Normal gain mode
Force receive mode on a specific MICS channel (status2)
AM receive mode
0
FM receive mode
1
Clock and data outputs gated for RSSI<energy threshold
0
1
Clock and data disabled until energy threshold met
Energy Threshold
Sets the threshold for either wake on energy or Sniff Mode. If the automatic noise floor detection is enabled in Sniff, the AMIS-53000
will overwrite the contents of this register each time a new threshold is calculated.
Table 35: Energy Threshold - 0X15 [21]
Bit
Name
Comment
7:0
E_Threshold
Energy detect threshold in DAC Mode = E_THRESHOLD*7.8125mV
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
50
AMIS-53000 Frequency Agile Transceiver
6.5.1.3.
Receiver Parameters
Figure 37: Receiver Sensitivity vs. Data Rate
Figure 38: RSSI Curve
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
51
Data Sheet
AMIS-53000 Frequency Agile Transceiver
6.5.1.4.
Data Sheet
Data Recovery
Table 36: Receiver Configuration
RX Configuration Registers
0X0E RX Config
0X1F CDR
Options A
0X0B Data Rate
Format
0X1E
Filter
Slice
Bit 2
Bit 0
Bit 3
Code
Bit 1:0
1
SLICE
Mod
0
0
FFT
FM
1
0
1
Demod
PLL
NA
6
AM
1
NA
6
0
NRZ
1
Man
0
NRZ
1
1
Man
Data Rage
Preamble
CDR
2
>20k – 128k
10Pattern
Yes
3
No
SLICE
2
>20k – 128k
10Pattern
Yes
3
No
SLICE
2
<20k
10Pattern
Yes
3
SLICE
2
1k – 19.2k
CW
1k – 19.2k
CW
<20k
All 1 or 0’s
Yes
3
0
NRZ
SLICE
2
1
Man
SLICE
2
1k – 19.2k
CW
Opt
7
1k – 19.2k
CW
Opt
7
0
NRZ
SLICE
2
1
Man
SLICE
2
SOF
4
No
0X55
0XAA
Opt
7
0X55
Opt
7
0X0A
0X55
0X0A
Notes:
1. Long strings of 1’s or 0’s will degrade the performance of the CDR circuits.
2. SLICE can use the parameters in Table 38.
3. Yes indicates that CDR is always used to detect the data. (SeeTable 41 and Table 42 for CDR parameters)
4. Manchester encoded data requires a SOF. A unique SOF (suggested 0x66) is used to bit-align the Manchester decoder to the recovered data.
5. 0X55 or 0X0A SOF have the following requirements:
0x55 The following is suggested:
It is suggested that CDR with fast phase alignment be enabled
It is suggested that CDR with activity check be enabled with 8 or 16 bit times
It is suggested that the preamble be long enough to trigger activity check (10 or 20 bit times)
0x0A The following is suggested:
It is suggested that CDR with fast phase alignment be enabled
It is suggested that CDR with activity check be enabled with 4 bit times
It is suggested that the preamble be long enough to trigger activity check
6. NA indicates that the parameter is not available for the AM/OOK modulated signals.
7. OPT indicates that CDR is an option to detect the data however, it is recommended that CDR be used. (See Table 41 andTable 42 for CDR parameters)
AM Data Recovery with RSSI
The logarithmic AM detector, used with OOK/ASK modulated signals, produces an RSSI output signal with approximately 18mV/dB
output level. A low pass filter provides additional filtering matched to the AM signal data rate (1.2, 1.8, 2.4, 4.8, 7.2, 9.6, 14.4,
19.2kbps). This filtered signal is sampled and compared to the slice threshold to recover the digital data. The slice threshold can be
set to a fixed value or it can use a signal tracking circuit to set a peak or average threshold.
The RSSI output signal can also be applied to a clock and data recovery circuit, which synchronizes an AMIS-53000 internal clock with
the incoming data rate (See CDR Operation).
Setup registers descriptions:
Slice Threshold- The slice operation needs to be selected, fixed or automatic. The value for the fixed threshold needs to be
set.
Filter/Slice- Filter settings and slice mode need to be selected.
Slice Threshold
Sets the data slice level for AM reception. This threshold is used when the slice method sets in the AM data filter and slice options is
set to DAC.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
52
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Table 37: Slice Threshold - 0X1D [29]
Bit
Name
Comment
7:0
SL_THRESH [7:0]
AM slice threshold in DAC Mode = SL_THRESH*7.8125mV
AM Data Filter and Slice Options
This register contains settings for determining the method of slicing for AM receive mode.
AM_FILTER: Sets the post-detection filter bandwidth for RSSI during AM receive. These filter bandwidths are set for the
corresponding data rates. These filter settings can also be used with custom data rates.
AM_HYST: Sets the amount of hysteresis in the AM slice comparator.
AM_SLICE: Used to select the method for providing a reference to the AM slice comparator. DAC Mode: This is a fixed
threshold level programmed into the slice threshold register.
Average Mode: This is an automatic threshold level where the AMIS-53000 sets the threshold level to the average level of
the RSSI signal. An external capacitor is required on the PEAK pin to set a bandwidth for the low pass filter response of the
averaging circuit. Due to the potential for long strings of 1’s or 0’s in NRZ data this threshold method is not recommended for
use with NRZ data.
Peak Mode: This is similar to the average mode, but only the highest level is determined from the incoming signal and the
AMIS-53000 sets the threshold to a level 6dB lower than the peak value. An external capacitor on the PEAK pin determines a
bleed off (discharge) rate for the peak detector circuit.
Table 38: AM Data Filter and Slice Options - 0X1E [30]
Bit
Name
State
Comment
000
RSSI filter bandwidth =300Hz
001
RSSI filter bandwidth = 600Hz
010
RSSI filter bandwidth = 1.2kHz
011
RSSI filter bandwidth = 2.4kHz
[7:5]
AM_FILTER[2:0] 100
RSSI filter bandwidth = 4.8kHz
101
RSSI filter bandwidth = 9.6kHz
110
RSSI filter bandwidth = 19.2kHz
111
RSSI filter bandwidth = 38.4kHz
4
NU
00
DAC mode: Slice threshold set in register 1Bh
01
Average mode: AM threshold set using averaging filter
[3:2]
AM_SLICE[1:0]
10
Peak detect mode: AM threshold set using peak detector
11
DAC mode: Slice threshold set in register 1Bh
00
0mV slice hysteresis
01
25mV slice hysteresis
[1:0]
AM_HYST[1:0]
10
50mV slice hysteresis
11
100mV slice hysteresis
FM FFT
The AMIS-53000 receiver uses a FFT function to recover data from a FM/FSK modulated signal when the data rate is higher than
20kbps. The FFT detector uses a two-bit DFFT to demodulate the incoming IF signal. This circuit also uses the same clock recovery
block (CDR) as the AM detector (See Section 6.1.4) to detect the data.
A pattern of 1’s and 0’s is required as a preamble. A SOF is not required unless Manchester encoded data is used, requiring a unique
preamble to bit-align the Manchester decoder to the recovered data.
Setup registers descriptions:
Data Rate- Can be specified in the discrete data rate register, or specified as a 16-bit word for a user defined data rate. (See
Section 7.1.3)
Peak Deviation- The peak deviation register stores the value to be used for both transmit and receive. In the FFT FM receive
mode, this value is used to set-up the FFT bins. (See Sections 6.4.1.5 and 6.4.1.6)
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
53
AMIS-53000 Frequency Agile Transceiver
Data Sheet
FM PLL Detector Loop Filter- For the discrete data rates, the values for the loop filter coefficients are pre-programmed. For
user defined data rates, this value needs to be calculated.
PLL Detector Loop Filter Setting
A program (AMIS-53CALC.exe available from AMIS) has been created to aid in the design of loop filter settings.
Table 39: PLL Detector Loop Filter Setting - 0X2B [43]
Bit
Name
Comment
7:0
PLL_CO [7:0]
PLL loop filter setting
FM PLL (Low Data Rate FSK)
The AMIS-53000 uses a PLL function to recover the data from a FM/FSK modulated signal with data rates 20kbps or lower. This circuit
uses an A DPLL for demodulation, the output of which is fed to the AM CDR circuit to recover the clock, and additionally filter the output
data.
The preamble sent by the AMIS-53000 when configured as NRZ FM is a repeating sequence of 1’s and 0’s. This gives the CDR circuit
and PLL demodulator sufficient edges to acquire lock. Hence, for the NRZ case it is unnecessary to include a SOF byte. In
Manchester mode, the preamble is specified as all 1’s (or 0’s). This gives the clock recovery circuit the most edges for lock acquisition.
However, due to the ambiguity of the preamble, a SOF byte is necessary for the Manchester decoding block. The suggested SOF for
this is either #55h or #AAh. The length of preamble necessary for this mode is dependant upon the loop bandwidth for the clock
recovery PLL.
Setup registers descriptions:
Data Rate- Can be specified in the discrete data rate register, or specified as a 16-bit word for a user defined data rate. (See
Section 7.1.3)
Peak Deviation- The peak deviation register stores the value to be used for both transmit and receive. In the FFT FM receive
mode, this value is used to set-up the FFT bins. (See Sections 6.4.1.5 and 6.4.1.6)
M PLL Detector Loop Filter- For the discrete data rates, the values for the loop filter coefficients are preprogrammed. For
user defined data rates, this value needs to be calculated. (See PLL Detector Loop Filter Setting)
6.5.1.5.
Clock and Data Recovery
The AMIS-53000 device performs clock and data recovery for both AM/OOK/ASK and FM/FSK signals. An internal clock in the
AMIS-53000 is programmed to be nearly the same rate as the expected data rate in the incoming signal. This clock is then
synchronized to the incoming data rate by extracting a clock from the data. This loop recovery method recovers data without much of
the jitter and noise associated with wireless communication links.
Before launching headlong into the operation of the detectors, and how to set them up, it is instructive to review the following related
registers, setup options and their functions.
Setup registers descriptions:
Fast Phase Alignment: In both the AM and PLL based FM modes (lower data rate), the AMIS-53000 can be configured to
quickly acquire phase lock on incoming data. The pattern necessary for the fast phase alignment is simply ‘1010’. This
function can be enabled in the CDR options A register. With this function enabled, the CDR circuit will operate with minimum
power consumption until the ‘1010’ sequence is received. A 32-bit correlation is used to not only recognize the 1010 pattern,
but also to instantaneously provide a phase correction to the clock recovery circuit allowing very fast (less than 4 bit) lock
times locking the incoming data.
Activity Check: This function can be used in conjunction with the fast phase alignment to reset the clock and data recovery
block back into its minimal power consumption mode when no transitions are detected on the data line for a specified period.
The check can be configured for 4, 8 or 16 bit times.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
54
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Over-Sampling Clock (Ts Clock): All three detectors use the Ts clock as the sampling clock for the transition from analog to
digital. This clock should be set to the highest rate possible, but not greater than 400x the data rate, to ensure adequate
phase information. For the discrete data rates, this value is pre-programmed for those rates.
Data Rate Clamp: The data rate clamp restricts the clock recovery circuit from wandering when an actual signal is not
present, and the phase error signals being generated come only from noise. Small fractional values for the clamp can lead to
longer lock times since the clock recovery PLL may not be able to make as large of a correction as is necessary all at once.
Channel Clamp: This clamping circuit is used to hold the low data rate FSK PLL detector within the specified limits to prevent
the PLL from wandering in the absence of signal.
CDR Operation
This circuit utilizes an all digital PLL (ADPLL) to recover the clock from the raw sliced data. The slicer output is integrated over a bit
time to provide a phase error, and the sign of the integration is used to determine the data symbol.
When using the AMIS-53000 in AM mode with any of the packet framing options enabled, it is necessary to have the SOF byte for
proper start-up of the AM CDR circuit. It is recommended that the CDR is set up with the activity check, and fast phase alignment
features enabled for the packet framing modes. The preamble that the AMIS-53000 will transmit in AM mode is CW, hence the SOF
byte is used by the fast phase alignment feature in the CDR to acquire lock. The suggested SOF for AM NRZ format is #55h. This will
provide the most transitions for the clock recovery circuit to acquire lock prior to the incoming packet. For Manchester operation, the
suggested SOF is #0A. This will provide early transitions for phase lock, and 4 bits to align the Manchester decode.
Because there are no transitions during the preamble in AM mode, the CDR relies on the fast phase alignment for acquiring lock. As
this is the case, the length of the preamble can be quite short as long as the activity check is enabled. The preamble should be long
enough to trip the activity detection circuitry such that the fast phase alignment circuit is reset at the beginning of the SOF. This
guarantees that the fast phase alignment will kick in during the SOF. The suggested length for the preamble is 4 BT’s for Manchester
with activity check set to 4 BT’s, and 10 or 20 for NRZ, with activity check set to 8 or 16 respectively. Note in the NRZ case, enabling
activity check will require the data be formatted to guarantee at least one transition in the data during the length of activity check (i.e.
every 8 or 16 BT’s).
Setup registers descriptions:
ID Dwell- Set a time that the CDR circuit will continue to search for the chip ID.
CDR Config- Set the parameters for the clock and data recovery circuits.
Data Rate- Can be specified in the discrete data rate register, or specified as a 16-bit word for a user defined data rate. (See
Section 7.1.3)
Start of Frame- Byte used to tell the AMIS-53000 receiver that data will start. (See Section 7.1.6)
Clock Recovery Loop Filter- For the discrete data rates, the values for the loop filter coefficients are pre-programmed. For
user defined data rates, this value needs to be calculated.
Chip ID Dwell Timer
Used to specify how long the clock and data recovery circuit will stay active after energy has been detected, looking for a valid chip ID.
The part will look for either the chip ID or the global ID.
Table 40: Chip ID Dwell Timer - 0X14 [20]
Bit
Name
Comment
00h: Code dwell timer disabled (for standard receive wake on code)
7:0
C_DWELL [7:0]
01h – FFh: Code dwell time = C_DWELL*bit time * 8
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
55
AMIS-53000 Frequency Agile Transceiver
Data Sheet
CDR Options A
This register contains settings for determining the clock and data recovery parameters.
DR_Clamp: Limits the CDR frequency drift between data packets.
Channel_Clamp: Restricts the bandwidth to the channel bandwidth.
Activity Check: Sets a number of bit times that the CDR circuit will shut down if there is no data present.
Fast Phase Alignment: Forces the CDR circuit to quickly synchronize to the incoming data.
FM Mode: The FM detector used in the receiver depends on the data rate of the incoming signal.
Table 41: CDR OptionsA - 0X1F [31]
Bit
Name
State
7,6
5,4
Channel Clamp
3,2
Activity Check <1>
1
FPA Enable
0
11
10
01
00
DR Clamp<1>
FM Mode
Comment
1/64
1/32
1/16
The clamp restricts the clock recovery PLL to +- the fraction selected
of the frequency selected by the BaudCLK which prevents clock
wandering between data packets
1/8
11
+-150
10
+-100
01
+-50
00
11
10
01
00
1
+-16
Reset after 16 bit times of no activity
Reset after 8 bit times of no activity
Reset after 4 bit times of no activity
Activity check disabled, clock recovery will always run
The CDR circuit will perform fast phase alignment
0
CDR always running
1
PLL
0
FFT
The clamp restricts the PLL detector to only lock on signals that are
within the specified window, centered +-500kHz of the IF frequency
CDR Options B
The sample clock values are written from ROM with the discrete data rate selected. The sample rate should be as fast as possible
without exceeding 400 samples per bit time.
Table 42: CDR OptionsB - 0X20 [32]
Bit
Name
State
1
7
CDR Reset
6
NU
5
NU
4
NU
3:0
Sample Clock
Comment
CDR is held reset
0
1011
1010
1001
1000
0111
0110
0101
0100
0011
0010
0001
0000
45kHz
90kHz
187.5kHz
375kHz
750kHz
1.5M
3M
6M
8M
12M
16M
24M
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
56
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Clock Recovery Loop Filter Setting
A program (AMIS-53CALC.exe available from AMIS) has been created to aid in the design of the CDR loop filter settings.
Table 43: Clock Recovery Loop Filter Setting - 0X2C [44]
Bit
Name
Comment
7:0
CDR_CO [7:0]
Clock recovery filter setting
6.6 Transmitter
Figure 39: Typical Output Power vs. Power Register Setting*
*Note: Curve is for output matched to 50Ω.
Table 44: Transmit Command
Register
Number (HEX)
Name
Code
0X00
Command
0X02
Function
Instruction to place the AMIS-53000 into transmit
(remember that all parameters for transmit must be set before issuing
this command)
The AMIS-53000 uses a switching class E power amplifier as the high power output driver. The high power PA can be bypassed to
allow a high efficiency at a lower output power. The output drivers are turned on and off directly in AM/OOK/ASK data modulation. A
direct modulation PLL is used to form the FM/FSK signal for transmission. The PLL loop runs at half of the desired transmit frequency
to provide excellent on/off ratio for AM, and to lower current consumption in the PLL.
OOK modulation (AM)
FSK modulation (FM)
Burst mode transmit
FM wave shaping
High power and low power range
Setup registers descriptions:
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
57
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Data Rate- Can be specified in the discrete data rate register, or specified as a 16-bit word for a user defined data rate. (See
Section 7.1.3)
RF Frequency- The RF frequency of the transmitter must be configured. (See section 6.4.1)
Output Power- Sets the RF output level for the AMIS-53000.
Peak Deviation- The FM deviation must be set for FM operation. (See section 6.4.1.5 and 6.4.1.6)
TX Config- Options for the transmitter must be set.
Preamble- Set a reasonable length of preamble to insure that the receiver can detect the signal.
6.6.1. TX Config
General options for transmit.
AM_FM_TX: Used to set the mode for transmit.
Shaping: When enabled, the FSK transitions are digitally shaped in the fractional N PLL with a pre-programmed sequence.
The filter for the shaping is Gaussian with a BT=1. This reduces the high frequency content of the data waveform that
modulates the carrier.
ID for TX: This option specifies which ID the AMIS-53000 will transmit when the use ID bit in general options A is enabled.
Global is used to transmit to all devices, chip ID will transmit the transmitters chip ID.
Buffered TX: When this option is enabled in conjunction with use ID and LOP enable, the packet for transmission is loaded
into internal RAM prior to the RF being enabled.
Force MICS Channel: When this bit is set to 1, bits[7:4] of Status2 can be written to force the transmitter to operate on a
specific MICS channel.
Clear Channel Assessment: When one of the CCA modes of operation are enabled, the AMIS-53000 will enable its receiver
to first check for the presence of energy on the specified channel before transmitting.
Table 45: TX Config - 0X0F [15]
Bit
Name
State
11
7,6
10
Clear Channel
01
Assessment
00
1
Force MICS
5
Channel
0
4
Smooth Turn On
1
Comment
Not allowed
MICS multi-channel assessment (pre-defined channels)
Single clear channel assessment prior to transmit (any frequency)
No clear channel assessment performed, normal operation
Enable smooth power up of PA (reduces the spurious response of the TX on
power up)
0
3
NU
2
ID for TX
1
0
Shaping
AM_FM_TX
1
Use the defined chip ID from the chip ID register
0
Use the defined global ID from the chip ID register
1
Gaussian FM data shaping enabled
0
FM data shaping disabled
1
AM transmit mode
0
FM transmit mode
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
58
AMIS-53000 Frequency Agile Transceiver
Data Sheet
6.6.2. Output Power
C_POWER: Coarse output power control for the power amplifier. When set high, the max out is 15dBm - when set low, the
max output is 0dBm.
F_POWER: Fine output power control for the PA. These 7 bits control the voltage on the RFPWR pin via an internal
DAC.F_POWER is sent to the DAC as the upper 6 bits. Lower 2 bits are 0.
Table 46: Output Power - 0X18 [24]
Bit
Name
Comment
7
6:0
C_POWER
Coarse output power selection sent to PA
F_POWER [6:0]
Fine output power control (upper 7 bits of the DAC, LSB of DAC=0)
6.6.3. Preamble Length
This byte is used to define the length of preamble to send prior to data in both transmit and Burst mode transmit.
Table 47: Preamble Length - 0X1A [26]
Bit
Name
Comment
7
PreambleLen [7:0]
Length, in bit times, of CW (AM), or ’10 (FM) sent prior to preamble in Burst
Table 48: Suggested Preambles
Modulation
Preamble
AM NRZ with CDR
CW
Comment
SOF required and suggested as 0X55
1
2
AM Manchester with CDR
CW
SOF required and suggested as 0x0A
FM FFT
FM PLL
(NRZ)
FM PLL (Manchester)
1/0 pattern
No SOF is required
1/0 pattern
No SOF is required
All 1s or 0s
SOF is required and suggested to be 55(Hex) or AA(Hex)
3
Notes:
1. When using SOF with NRZ data, it is suggested that fast phase alignment is enabled, activity check is set to 8 or 16 and preamble length is 10 or 20 bit times.
2. When using SOF with Manchester coded data, it is suggested that fast phase alignment is enabled, activity check is set to 4 bit times and preamble length is set long
enough to trigger the activity check.
3. The length of this preamble is dependent on the loop bandwidth of the recovery clock PLL.
6.6.4. FM Transmit Data Shaping
The AMIS-53000 allows the user to enable data shaping of the data waveform to improve the RF spectral efficiency. When enabled,
the clock recovery NCO is used to provide an internal clock at 16 times the selected data rate. This clock is used to cycle through a
pre-defined pattern whenever a transition is detected on the TX input. The shaping pattern is Gaussian with a BT=1. The intermediate
values for the shaping are determined from the peak deviation register when an external host/controller writes the ‘ROM 2 REGS’ to the
AMIS-53000 command register.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
59
AMIS-53000 Frequency Agile Transceiver
Data Sheet
6.7 Idle
Table 49: Idle Command
Register
Number (HEX)
Name
0X00
Command
Code
0X03
Enable the idle state
0X04
Return to idle state
Table 50: Idle Configuration
Register
Number (HEX)
Name
0X02
Status/Flag2
0X0C
General Options A
0X0D
General Options B
Function
Bits
Function
0
AMIS-53000 is busy
2:1
Select state that AMIS-53000 enters on POR
0
Output system clock in standby mode
1, 0
Select the system clock frequency
Note that there are two low-power modes for AMIS-53000 – standby and idle. Standby allows the SYSCLK output. Idle is the very low
power state without SYSCLK output.
Table 51: Idle Modes
Idle Tasks
Description
Sniff
Receiver periodic wake up and RF energy detection check
Burst Transmit
Periodic wake and transmit function
Housekeeping
Used to perform periodic temperature correction, calibration or to wake external host/controller
Standby
Low-power mode with no activity may be programmed to continue to output system clock
The AMIS-53000 allows for a low-power mode. Power requirements are reduced when the very low power 10kHz oscillator is the clock
for the device. This oscillator runs the timers for either the Sniff wake up timer, the Burst transmit timer or the housekeeping wakeup
timer. However, even when the low power 10kHz oscillator is running, the AMIS-53000 can still provide a clock signal output to an
external host/controller device such as a microprocessor after reception of a valid data packet or a housekeeping cycle where the
AMIS-53000 has been programmed to issue a wake up to the external host/controller.
The AMIS-53000 will return to this low power idle state after activities such as transmit, receive or the various timers are done and the
external host/controller writes the ‘Return to Idle’ instruction to the AMIS-53000 command register.
Setup registers descriptions:
Idle Config- The options for idle mode must be set.
6.7.1. Idle Config
The idle configuration register is used to specify which periodic tasks are performed once the idle command is given in register 0. Any
combination of Sniff, Burst and housekeeping can be enabled.
INT to DSSN Timing: This is the time between the AMIS-53000 issuing an interrupt to indicate that data is ready and the time
that data transfer starts with the assertion of the DSSN signal.
Idle to System Clock Stop: Once the AMIS-53000 has completed a task and is issued the idle command, the system clock
can produce additional clock cycles to allow the external host/controller to finish its tasks.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
60
AMIS-53000 Frequency Agile Transceiver
Table 52: Idle Config - 0X10 [16]
Bit
Name
7:5
Wait timing between
INT and DSSN for
Sniff Receive
4,3
Wait timing between
idle instruction and
system clock shutoff
time
2
Housekeeping
Enable
1
Burst Enable
0
Sniff Enable
State
111
…
000
11
Comment
10
System clock outputs 512 clock cycles before shutdown after idle command
01
System clock outputs 256 clock cycles before shutdown after idle command
00
System clock immediately shuts down after idle command
1
Periodic housekeeping enabled (HK settings must be set)
Data Sheet
DSSN going active is delayed 8 bit times from INT
DSSN is immediately active after INT
System clock outputs 1024 clock cycles before shutdown after idle command
0
1
Periodic Burst mode enabled (BURST settings must be set)
0
1
Periodic Sniff Mode enabled (Sniff settings must be set)
0
6.7.2. Sniff Mode Operation
Table 53: Sniff Mode Configuration
Register
Number (HEX)
Name
0X0E
RX Config
0X10
Idle Config
Bits
1
Function
Force the receiver to not output Clk&Data < energy level
0
Set the receiver to wake when at energy level threshold
2
Enable periodic Sniff Mode
The quick start technology enables the AMIS-53000 to operate its receiver in a mode called Sniff Mode. As implemented in the
AMIS-53000, this Sniff Mode can wake the receiver and acquire the transmitted message in as little as 130 microseconds.
Figure 40: Sniff Waveform
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
61
AMIS-53000 Frequency Agile Transceiver
Data Sheet
The Sniff Mode of operation puts the AMIS-53000 receiver into a cyclic mode of sleeping and periodically waking to check for received
signal energy. When energy is detected the receiver is placed in receive mode and the AMIS-53000 attempts to recover data. The
receiver in Sniff Mode can be configured to check for a valid ID. The failure to receive a valid ID will cause the receiver to go back to
sleep.
The AMIS-53000 receiver average supply current can be estimated as:
Where,
is receiver current consumption in continuous receive mode, equal to or less than 12mA;
is receiver current consumption in sleep mode, equal to or less than 2uA;
is programmable receiver energy scan impulse on time (sniff time), approximately equal to 130µs minimum;
is programmable receiver off time period length between receiver energy scan impulses (sniff mode interval).
Setup registers descriptions:
Sniff Config-This sets the options in the Sniff Mode.
Sniff Interval- Set the time interval between receiver wakeups in the Sniff Mode.
Energy Threshold- The threshold for detecting the incoming RF energy must be set (see Section 6.5.1.2).
Energy Dwell Time- Set the time interval that the receiver will remain active looking for RF energy detection.
Code Dwell Time- Once RF energy has been detected the receiver can determine if the message has the unique ID for that
receiver. The time interval for looking for this ID must be set. (See Chip ID Dwell Timer)
Threshold- The number of times a wake up is received can be monitored for false wake ups and the energy threshold
adjusted to account for the noise level.
6.7.2.1.
Sniff Config
The Sniff config register is used to set additional options for the operation of the part during a Sniff cycle, beyond those set in the RX
config register.
SNIFF_FILTER: Setting for the energy detection filter. This allows for different settings of the AM data filter between Sniff and
receive. The energy dwell timer needs to be extended long enough to allow for this filter to settle during the Sniff cycle.
Auto-Threshold Count Value: Number of Sniff cycles used to determine whether to raise or lower the energy threshold for
sniff. Any value other than 0x00 in this register will enable the auto-threshold function.
Multi Channel: This bit is used in MICS mode of operation to enable the AMIS-53000 to scan the nine pre-defined MICS
channels programmed into the AMIS-53000.
Sniff Interval Resolution: Determines the clock for the Sniff interval timer.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
62
AMIS-53000 Frequency Agile Transceiver
Table 54: Sniff Config - 0X11 [17]
Bit
Name
State
000
001
010
SNIFF_FILTER
011
7:5
100
101
110
111
11
4,3
Auto-Threshold
Count Value
10
01
00
2
NU
1
NU
0
Sniff Interval
Resolution
6.7.2.2.
1
0
Data Sheet
Comment
RSSI filter bandwidth =300Hz
RSSI filter bandwidth = 600Hz
RSSI filter bandwidth = 1.2kHz
RSSI filter bandwidth = 2.4kHz
RSSI filter bandwidth = 4.8kHz
RSSI filter bandwidth = 9.6kHz
RSSI filter bandwidth = 19.2kHz
RSSI filter bandwidth = 38.4kHz
This is the number of Sniff cycles to count false wake ups due to the
100
noise level, so that the threshold level can be adjusted. It is
500
adjusted higher when the number of false wake ups exceeds the
100
wake up target number. It is adjusted down when there are fewer
false wake ups than the target number. Entering a number other
Disable
than 00 in this register will enable the auto-threshold.
Sniff interval timer resolution is 100ms (interval between Sniff signal detection
events is (Sniff interval) times (Sniff resolution)
Sniff interval timer resolution is 500us 100ms (interval between Sniff signal
detection events is (Sniff interval) times (Sniff resolution)
Sniff Interval Timer
Used to specify the period (time between Sniff events) of the Sniff operation. The Sniff interval is this value times the Sniff interval
resolution value (set in the Sniff config register).
Table 55: Sniff Interval Timer - 0X12 [18]
Bit
Name
Comment
7:0
6.7.2.3.
SNIFF_INT [7:0]
Sniff interval timer =SNIFF_INT* Sniff interval timer resolution
Energy Dwell Timer
Length of time receiver will stay on in a Sniff cycle checking for the presence of a signal. Also used for a receive command when the
wake on energy bit is asserted in RX config. When used for a MICS market device, this may need to be set to 10 milli-seconds for CCA
to be compatible with the MICS standard.
Table 56: Energy Dwell Timer - 0X13 [19]
Bit
Name
Comment
00h: Energy dwell timer not used, energy determined by an impulse sample
7:0
01h – FEh: Energy dwell time = E_DWELL * 100us
E_DWELL[7:0]
FFh: Receiver remains on until energy threshold is met
6.7.2.4.
Energy Threshold
Sets the threshold for either wake on energy or Sniff Mode signal acquisition. If the automatic noise floor detection is enabled in Sniff,
the AMIS-53000 will overwrite the contents of this register each time a new threshold is calculated.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
63
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Automatic Threshold Optimization in Sniff Mode
An option available in the Sniff Mode config register will enable the AMIS-53000 to automatically adjust the energy threshold of the
AMIS-53000 to optimize the sensitivity of the Sniff Mode. The target number of wake ups (register 0X2F) allows the user to specify a
value for the number of false wake ups the AMIS-53000 is allowed with the selected configuration of the Sniff Mode (by bits [4:3] in the
SNIFF_CONFIG register) number of Sniff cycles.
As an example:
If the number of Sniff cycles is set to 500 (Sniff config [Bit 4:3]),
If the target number of false wake ups is set to 50 (target number wake ups),
Then over the course of the next 500 Sniff cycles the radio is triggered falsely by energy:
More than 50 times, the threshold will be increased to reduce the sensitivity,
Less than 50 times, the threshold will be decreased to increase the sensitivity.
Using this option to set the threshold for energy detection can have a dramatic impact on the life of battery powered devices, as the
AMIS-53000 will adjust to changing levels of background noise while still maintaining maximum sensitivity, and not wasting power by
continually waking and processing background noise.
Additionally, the energy threshold setting can be monitored by an external host/controller. The amount the threshold will increase or
decrease is based on Table 57, with the order of the rows in the same order as the AMIS-53000 will evaluate the conditions.
Table 57: Auto Threshold Adjust
Condition
Adjustment
Select the number of Sniff cycles as the test period
Enter the desired number of false wake ups per
period
Note: a false wake up is when the receiver detects energy but fails to detect the ID in the
packet
Then if wake ups/period > target
Threshold is increased
Then if wake ups/period < target
Threshold is decreased
The threshold of the AMIS-53000 can vary over a wide range from one device to the next, due to design, manufacturing tolerances, and
environment changes; temperature and voltage. This automatic threshold optimization can be used to adjust the threshold by
monitoring the level of false wake ups due to background noise. The adjustment in this fashion can reduce the effects of design and
manufacturing on the threshold setting of the AMIS-53000.
Setup registers descriptions:
Target- Set a value for the allowed number of false wake ups desired.
Target Threshold
The number of false wake ups occurring during a period of time is used to automatically adjust the energy threshold in the Sniff
operation. This allows the AMIS-53000 to automatically adjust its input level to compensate for, manufacturing, components,
environment, temperature, and/or voltage.
Table 58: Target Wake Ups - 0X2F [47]
Bit
Name
Comment
The number of wake-ups that the Sniff circuit will try to adjust the threshold to not have
more false wake ups or less missed signal detections. This register allows the number to
7:0
Target [7:0]
be 0 to 255, but this number should always be less than the number of Sniff count (Sniff
config bit 4:3).
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
64
AMIS-53000 Frequency Agile Transceiver
Data Sheet
6.7.3. Burst Transmit Data
Table 59: Burst Transmission Configuration
Register
Number (HEX)
Name
Bits
0X10
Idle Config
1
Function
Enable Burst transmissions
Burst mode of transmission is a function that can cause the AMIS-53000 to transmit a message at a programmed time interval or by
asserting the xBURST pin to active (the AMIS-53000 must be in the xBURST mode), causing the AMIS-53000 to immediately transmit
a message. The Burst mode can also be started by enabling the Burst mode in the idle register and then writing to the command
register to set the AMIS-53000 into idle mode. The xBURST modes sets a timed automatic transmission of register values (a message)
or ADC conversion values.
Setup registers descriptions:
Burst Config- Set the Burst transmission parameters.
Burst Interval- Set the time interval between Burst transmissions.
User DataA- Message for timer initiated transmissions.
User DataB- Message for xBURST initiated transmissions.
Figure 41: Data Packet Format Showing Order for Burst TX Content
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
65
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Used to set the options for the Burst mode of operation:
R_BURST: These bits set the number of times the packet is to be repeated each Burst interval. This can be used to increase
the probability that all packets will get through when several Burst transmitters are located in the same area.
Send Chip ID: This option is included to allow for the operating case of having multiple transmitters sending to a single
receiver. The multiple transmitters will need to be configured to send the global chip ID in the TX config options so that the
receiver will wake on each transmitters packet. Sending the chip ID as part of the payload allows the receiver to differentiate
the packets.
Send Internal ADC Data: When enabled, the AMIS-53000 will perform conversions on the battery voltage, and temperature
sensor and include these conversions as part of the packet payload.
Send External ADC Data: When enabled, the AMIS-53000 will perform conversions on the two external ADC inputs and
include these conversions as part of the packet payload.
Burst Interval Resolution: Used to define the clock frequency for the Burst interval timer.
Table 60: Burst Config - 0X16 [22]
Bit
Name
State
Comment
1
7
0
1
6
0
00
01
10
11
1
Packet is sent one time
Packet is repeated once
Repeat interval*
Packet is repeated two times
Packet is repeated three times
Chip ID is included as part of the packet
5:4
R_BURST[1:0]
3
Send Chip ID
2
Send Internal
ADC Data
1
1
Send External
ADC Data
1
0
Burst Interval
Resolution
1
Burst interval timer resolution is 15s
0
Burst interval timer resolution is 50ms
0
Data for temperature and battery is sent
0
Data for EXT1, EXT2 is sent
0
NOTE: When the Burst transmission is repeated the interval between transmissions is a random time period produced in a random number generator with the chip ID value
used to seed the random number generator.
6.7.3.1.
Burst Interval
Defines the period for the normal Burst transmission to occur. This is a cyclic mode and the AMIS-53000 will transmit the contents of a
register at the end of each interval. This interval is fixed by the register value unlike the random time interval when the transmission is
repeated.
Table 61: Burst Interval - 0X17 [23]
Bit
Name
Comment
7:0
BURST_INT [7:0]
Burst interval= (BURST_INT+1)*Burst interval resolution
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
66
AMIS-53000 Frequency Agile Transceiver
6.7.3.2.
Data Sheet
User Defined Data A
Table 62: User Defined Data A - 0X2D [45]
Bit
Name
Comment
7:0
6.7.3.3.
USE_DATAA [7:0]
Optional data to be sent in normal Burst mode if non-zero
User Defined Data B
Table 63: User Defined Data B = 0X2E [46]
Bit
Name
Comment
7:0
USE_DATAB [7:0]
Optional data to be sent in interrupt triggered burst if non-zero
6.7.4. Housekeeping
Table 64: Housekeeping Enable
Register
Number (HEX)
Name
Bits
0X10
Idle Config
0
Function
Enable housekeeping timed functions
Housekeeping is another periodic operation mode, which can be used to periodically perform operations such as oscillator calibrations,
PLL calibration, EE refresh, or temperature compensation. It can also be used to periodically wake an external host/controller to allow it
to perform whatever tasks it may need to. The housekeeping configuration register contains the options to specify what is to occur
during a housekeeping cycle, and the housekeeping interval timer is used to control how frequently the wake up occurs.
Setup registers descriptions:
Housekeeping Config- Set the Burst transmission parameters.
Housekeeping Interval- Set the time interval between Burst transmissions.
6.7.4.1.
Housekeeping Config
The housekeeping configuration register is used to specify which tasks the AMIS-53000 should perform during a housekeeping cycle.
HK Interval Resolution: Used to specify the clock frequency for the housekeeping interval timer.
Wake: When enabled, the AMIS-53000 will enable the system clock output, and issue an interrupt to an external controller.
Write EE: This option is used to store the values of any calibrations that may have been performed during housekeeping.
The entire working register bank will be written to EE.
Read INT ADC Channels: The AMIS-53000 will do conversions on the battery voltage and temperature sensor. This can be
used as a method to periodically update the temperature compensation loop.
Read EXT ADC Channels: When enabled, the two external ADC inputs will be converted during a housekeeping cycle.
Cal PLL, RC, Kicker: Allows periodic calibration of the oscillators of the AMIS-53000.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
67
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Table 65: Housekeeping Config - 0X1B [27]
Bit Name
State
Comment
HK Interval
1
Five minute resolution setting
7
0
One second resolution setting
Resolution
1
6
Wake
5
Write EE
4
Read INT
ADC Channels
1
3
Read EXT
ADC Channels
1
2
Cal PLL
1
Cal RC
0
Cal Kicker
Issue interrupt and enable clock to external host/controller
0
1
Current register data written to EE (performed after all Cal’s complete)*
0
Temp sensor and battery inputs converted
0
EXT1 and EXT2 ADC inputs converted
0
1
PLL calibration performed during housekeeping
0
1
RC oscillator calibration performed during housekeeping
0
1
Kicker calibration performed during housekeeping
0
Note: * Bit 5 is set high to allow the EE to be automatically written after a calibration is complete.
6.7.4.2.
Housekeeping Interval
Sets the interval (time that the AMIS-53000 is in sleep mode) for the housekeeping routine.
Table 66: Housekeeping Interval - 0X1C [28]
Bit
Name
Comment
7:0
HK_INT [7:0]
Housekeeping interval = (HK_INT+1)* (HK interval resolution)
6.8 Idle Return
Table 67: Idle Return
Register
Number (HEX)
Name
Code
0X00
Command
0X04
Function
In most conditions, the AMIS-53000 must be returned to idle mode at
the end of a task by this command
This command is used to put the part back into idle mode. It should be used by the host to place the AMIS-53000 back into idle mode
after the AMIS-53000 has interrupted the host for reception of a packet in Sniff, or to end a housekeeping cycle.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
68
AMIS-53000 Frequency Agile Transceiver
Data Sheet
6.9 EE
The AMIS-53000 uses internal EE memory to store register settings (either default factory settings or user defined settings).
Table 68: Calibration Results
Register
Number (HEX)
Name
0X00
Command
0X01
Status/Flag1
Housekeeping
Config
0X1B
Bits
Function
0X05
Write the register contents to EE
0X06
Read the contents of the EE
2
EE checksum status
5
Write register data to EE (auto after calibration complete)
6.9.1. Write EE
The serial interface provides a means to read and write the working registers of the AMIS-53000. To retain the information held by
these registers, on-board EE is provided to store all of the register contents needed for operation. The write EE command copies the
current contents of the working registers into EE, along with a CheckSum. The CheckSum is used to verify that the content of the EE is
valid when the EE is dumped back into the registers.
6.9.2. Load EE
The load EE command will refresh the contents of the working registers with the values stored in EE, if the EE CheckSum is valid. If
the EE CheckSum fails an error bit will be set in the Status2 register.
6.10 Calibrate
Table 69: Calibration Results
Register
Number (HEX)
0X00
Name
Command
0X01
Status/Flag1
Housekeeping
Config
0X1B
Kicker Slope
Options
0X33
Bits
Function
0X07
Perform a Quick Start oscillator calibration
0X08
Perform a 10kHz RC oscillator calibration
0X09
Perform a PLL calibration
0X0A
Perform a Quick Start oscillator calibration
6
TX PLL calibration status
5
RX PLL calibration status
4
10kHz RC oscillator calibration status
3
Quick Start oscillator calibration status
2
Perform the PLL calibration
1
Perform the 10kHz RC oscillator calibration
0
Perform the kicker calibration
4
Kicker calibration status
Setup registers descriptions:
Trim- Shows the trim value for the circuit.
PLL Trim Target- Set a value that the PLL trim tries to achieve in calibration.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
69
AMIS-53000 Frequency Agile Transceiver
Data Sheet
6.10.1. Internal Trim
6.10.1.1. Crystal Trim
Table 70: Crystal Trim - 0X21 [33]
Bit
Name
Comment
7:0
XTAL_TRIM [7:0]
24MHz internal trim caps; FF is max capacitance, 00 is min
6.10.1.2. LNA Trim
Table 71: LNA Trim - 0X22 [34]
Bit
Name
Comment
7:4
LNA_OUT[3:0}
LNA output tank cap trim F is max cap
3:0
LNA_IN [3:0]
LNA input shunt capacitor trim, F is max, 0 is min
6.10.1.3. Quick Start Oscillator Trim
This register contains the value of the trim from the self calibration.
Table 72: Quick Start Oscillator Trim - 0X23 [35]
Bit
Name
Comment
7:0
6.10.1.4.
QS_TRIM [7:0]
Trim for the Quick Start (kicker), this register is written to by the calibration circuit
10K Oscillator Trim
This register contains the value of the trim from the self calibration.
Table 73: 10kHz Oscillator Trim - 0X24 [36]
Bit
Name
Comment
7:0
RC_TRIM [7:0]
Trim for the 10kHz oscillator, this register is written by the calibration circuit
6.10.1.5. Analog Trim1
This is an internal use register with no user defined meaning. This register is set at the factory and changing the value will cause the
AMIS-53000 to not operate.
6.10.1.6. Analog Trim2
This is an internal use register with no user defined meaning. This register value is set at the factory and changing the value will cause
the AMIS-53000 to not operate.
6.10.1.7. RF PLL Trim
This register contains the value of the trim from the self calibration. This register is valuable to monitor to determine if the PLL trim
calibration passed, but with the highest trim value or lowest trim value which indicates that the trim is nearly all the way to the edge of
the calibration.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
70
AMIS-53000 Frequency Agile Transceiver
Table 74: RF PLL Trim - 0X27 [39]
Bit
Name
State
Data Sheet
Comment
7
6:4
TX Mode PLL
Trim Value
111
--
Max VCO trim value from the self calibration
Min VCO trim value from the self calibration
000
3
2:0
RX Mode PLL
Trim Value
111
--
Max VCO trim value from the self calibration
Min VCO trim value from the self calibration
000
6.10.1.8. PLL Target Value
This register is used by the AMIS-53000 during self calibration. This is an internal use register with no user defined meaning.
6.10.2. Calibrate Quick Start Oscillator
The Quick Start oscillator must be calibrated prior to operations such as Sniff or Burst transmit. This command will perform an internal
calibration of the oscillator, write the result to the Quick Start trim register, issue a calibration complete flag, as well as a calibration
good/bad indicator. This command can be issued from any valid state that accepts changes in the instructions.
6.10.3. Calibrate 10kHz Oscillator
In any of the idle modes of operation, an internal 10kHz oscillator is used as the timekeeping reference for the interval timers. The
calibrate 10kHz oscillator command will enable the crystal oscillator to create an accurate time base to use for the calibration of this
oscillator, and then perform the calibration and store the result. A Cal done and status flag will be issued upon completion of the
calibration. This command can be issued from any valid state that accepts changes in the instructions.
6.10.4. Calibrate PLL
Calibrate the PLL performs a calibration for the PLL in both transmit and receive mode. The PLL status register reports the calibration
value for both modes, as well as the status for the calibration. This command can be issued from any valid state that accepts changes
in the instructions.
6.10.5. Calibrate LNA
This command turns on the RF receiver chain and optimizes both the LNA output tuning structure and the LNA input matching trim for
maximum signal level on RSSI. This is a calibration typically performed at board assembly in the presence of a known RF signal. The
AMIS-53000 will auto-tune both the input and output internal variable capacitances of the LNA to optimize gain, compensating for the
tolerance of external components for the match.
6.11 ROM 2 REGS
This command starts internal AMIS-53000 processes such as:
Multi-Channel: Calculates the frequency information to form nine channels of 300kHz bandwidth. Four of these channels
are at higher frequencies than the programmed RF frequency and four channels are at lower frequencies.
Wave Shaping: Calculates the voltage steps to form the Gaussian wave shaping of the data for the data rate selected.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
71
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Defined Data Rates: Calculates all the parameters for the selected data rate (selected from the defined data rates).
RF Frequency: Calculates the parameters needed to set the TX/RX frequency
AM Filters: Calculates parameters for the filter defined by the data rate selection (defined data rates).
6.12 Chip Reset
Resets the entire chip, similar to a POR. This operation will reset the unlock test MUX register.
6.13 ADC Conversion
Table 75: ADC Configuration
Register
Number (HEX)
Name
0X00
Command
Bits
Function
010xxxxx
Perform a single ADC conversion (see Table 84)
110xxxxx
Perform continuous ADC conversions (see Table 85)
The ADC conversion has completed
0X01
Status/Flag1
0
0X1B
Housekeeping
Config
4
Do an ADC conversion for the internal measurements
3
Do an ADC conversion for the external measurements
The AMIS-53000 contains an 8 bit analog to digital converter. This ADC can measure the voltage on a number of internal functions,
battery voltage, temperature, received signal strength indication voltage, and loop filter voltage. The results of these conversions are
available through reading the registers where that data is stored or by using the feature of the Burst transmission to send that
information to another node. The AMIS-53000 also contains two ADC channels available on the device pins. The ADC can convert
signals at a conversion rate up to 128k samples/second.
Setup registers descriptions:
Temp- Contains the value from the last ADC of the internal temperature sensor.
Battery- Contains the value from the last ADC of the internal battery voltage (divided by 2).
RSSI- Contains the value from the last ADC of the signal level sample in the receiver.
ADC1- Contains the value from the last ADC of the external analog input.
ADC2- Contains the value from the last ADC of the external analog input.
Loop Filter- Contains the value from the last ADC of the loop filter voltage.
6.13.1. ADC Conversion Results
6.13.1.1. Temp ADC
Table 76: Temp ADC - 0X34 [52]
Bit
Name
Comment
7:0
TEMP_ADC [7:0]
Temperature sensor ADC reading
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
72
AMIS-53000 Frequency Agile Transceiver
Data Sheet
6.13.1.2. Battery ADC
Table 77: Battery ADC - 0X35 [53]
Bit
Name
Comment
7:0
BATT_ADC [7:0]
Battery voltage ADC reading (Vbatt/2)
6.13.1.3. RSSI
Table 78: RSSI - 0X36 [54]
Bit
Name
7:0
RSSI_ADC [7:0]
Comment
RSSI voltage ADC reading
6.13.1.4. External Input 1 ADC
Table 79: External Input1 ADC - 0X37 [55]
Bit
Name
Comment
7:0
EXT1_ADC [7:0]
External input 1 ADC reading
6.13.1.5. External Input 2 ADC
Table 80: External Input2 ADC - 0X38 [56]
Bit
Name
Comment
7:0
6.13.1.6.
EXT2_ADC [7:0]
External input 2 ADC reading
Loop Filter
Table 81: Loop Filter - 0X39 [57]
Bit
Name
Comment
7:0
LOOP_FILT [7:0]
Internal loop filter
6.13.2. Single ADC Conversion
The single conversion command performs an ADC conversion on the channel specified as part of the command. Once complete, a flag
is set, and the 8 bit data for the conversion is available in its associated register.
Table 82: Single ADC Conversions
Register
Number
Bits
Name
(HEX)
(7:6)
01
0X00
Command
Bits
(5:0)
000001
Function
01
000010
Perform an ADC on the external input 2
01
000100
Perform an ADC on the internal temperature sensor
01
001000
Perform an ADC on the Internal battery voltage
01
010000
Perform an ADC on the receiver RSSI
01
100000
Perform an ADC on the loop filter
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
Perform an ADC on the external input 1
73
AMIS-53000 Frequency Agile Transceiver
Data Sheet
6.13.3. Continuous ADC Conversion
This command can be given to the radio and operate in parallel with transmit or receive. This mode can also be entered into from an
idle state. In this mode the specified ADC channel is continuously converted, and its associated register is continuously over written.
Table 83: Single ADC Conversions
Register
Number
Bits
Name
(HEX)
(7:6)
11
0X00
Command
Bits
(5:0)
000001
Function
11
000010
Perform continuous ADC on the external input 2
11
000100
Perform continuous ADC on the internal temperature sensor
11
001000
Perform continuous ADC on the internal battery voltage
11
010000
Perform continuous ADC on the receiver RSSI
11
100000
Perform continuous ADC on the loop filter
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
Perform continuous ADC on the external input 1
74
AMIS-53000 Frequency Agile Transceiver
Data Sheet
7.0 Data Interface
Table 84: Control/Data Interface Physical Configuration
Interface
2
IC
Function
Control
Control
3 -Wire
4-Wire
Data
Data
Clock
Data
Select
AMIS-53000
Data Buffering
SDATA
None
Slave only
N/A
Pin
Source
Output
Input
SCLK
Master
SDATA
SCLK
Master
SDATA
SDATA
SSN
Slave only
N/A
DCLK
Master
DRXTX
DRXTX
DSSN
Master
Optional
DCLK
Master
DRXTX
DRXTX
DSSN
Slave
Buffered only
DCLK
Master
DRXTX
DOPT
DSSN
Master
Optional
DCLK
Master
DRXTX
DOPT
DSSN
Slave
Buffered only
Figure 42: 4-Wire SPI Compatible Data Interface
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
75
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Figure 43: 3-Wire Serial Data Interface
The AMIS-53000 employs two different data interfaces. Transmit and receive data is exchanged with an external controller through
either a 3-wire or a 4-wire SPI like interface. Selecting the interface, 3-wire or 4-wire is done by writing to bit 7 of the general options B
register.
SPI serial data interface
3-wire serial data interface
AMIS-53000 can be the slave or master
Setup registers descriptions:
Chip Address- Allows a unique value to be transmitted and received with the data packet to identify a unique radio.
Fixed Data Rates- Select the options for one of several fixed data rates.
General Options A- Configure the interface options.
General Options B- Configure the interface options.
Start of Frame- Set a code value that indicates the start of a data packet.
Preamble Length- Select a type of preamble and set the length in bits. (see Section 6.6.3)
Custom Data Rates- Configure parameters for data rates that are not one of the fixed data rates.
CRC Polynomial- Value of the CRC polynomial.
Default Length of Packet- Set a default length for packets.
Broad Cast ID- A general chip ID allowing for transmissions to be received by all radios.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
76
AMIS-53000 Frequency Agile Transceiver
Data Sheet
7.1.1. Chip Address MSB1
The 16 bit ID that can be used for several purposes in the AMIS-53000 is stored in the chip address MSB, and chip address LSB
registers.
Table 85: Chip Address1 - 0X03 [3]
Bit
Name
Comment
7:0
Chip_Add [15:8]
Upper byte of chip address
7.1.2. Chip Address LSB
Table 86: Chip Address0 - 0X04 [4]
Bit
Name
Comment
7:0
Chip_Add [7:0]
Lower byte of chip address
7.1.3. Data Rate/Format
The data rate/format register is used to select the data rate and format for both receive and transmit. The DDRATE[2:0} option bits
allow selection of one of eight pre-programmed data rates. When one of the discrete data rates is selected, the ROM2REGS command
is used to load clock and data recovery settings for the desired data rate into their associated registers.
The Manchester option bit configures the AMIS-53000 to transmit and receive in the Manchester encoded format, while the data
interface remains NRZ.
If a data rate other than one of the available discrete rates is desired, the user should set the use custom bit, and then program the
custom data rate register for the desired data rate. When the use custom data rate option is enabled, it is up to the user to set the
correct sample clock frequency in the CDR options B register, set clock recovery loop filter settings, and if using the PLL based FSK
detector, set the PLL detector loop filter.
Note: For data rates that are near one of the pre-defined data rates, a discrete data rate could first be chosen, the ROM2REGS
command given to load all of the settings for the various blocks for that data rate, and then the custom data rate option enabled and the
new data rate information entered.
For example, if the desired data rate is 100kbps, set DDRATE to 110 for 96kbps operation. Next, issue the ROM2REGS command in
the command register. All of the proper settings for the clock and data recovery circuit for a 96k data rate will be loaded into the
working registers from ROM (sample clock frequency, clock recovery loop filter settings). Finally, enable the use custom option, and
program data rate 1, and 0 with the value for a 100k data rate.
Custom frequency is set in data rate 1 and data rate 0. If custom is 0, ROM contents for selected discrete data rate are loaded into
data rate 1 and data rate 0.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
77
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Table 87: Data Rate/Format - 0X0B [11]
Bit
Name
State
Comment
7
NU
6
NU
5
NU
4
Use Custom
3
Manchester
2:0
DDRATE [2:0]
1
Enables user programmable data rate
0
1
Manchester encoding selected
0
000
001
010
011
100
101
110
111
NRZ encoding selected
1.2kbps
2.4kbps
4.8kbps
9.6kbps
19.2kbps
57.6kbps
96kbps
128kbps
7.1.4. General Options A
The general options A register contains a number of options that specify the operation of the part in its various modes.
Standby Mode: Determines whether the crystal oscillator is enabled during standby. For applications relying on the
AMIS-53000 to provide and external host/controller with a system clock, this bit should be enabled, and is the default state.
POR State: Specifies the power on state of the device. Once this has been stored into EE, the device will power up in the
chosen state after the EE has been shadowed into the working registers.
Pull up Disable: For applications not using an open drain type driver to drive the register interface pins (SDATA, SCLK and
SSN) the pull ups on these pins can be disabled via this option bit to save power.
Temperature Compensation: When enabled, the ADC output for the temperature sensor is used to compensate the RF
center frequency for crystal frequency error. A new correction factor is calculated each time the ADC performs a new
conversion on the temperature sensor.
CRC Enable: Enables internal CRC checking in RX, and appends a CRC in TX.
Length of Packet Enable: Allows buffering of packets, also allows CRC when enabled.
Use ID in RX and TX: When enabled, in receive mode the part will not output data until a valid ID is found, and in TX, the part
will automatically send preamble and chip ID before enabling the data interface.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
78
AMIS-53000 Frequency Agile Transceiver
Table 88: General OptionsA - 0X0C [12]
Bit
Name
State
7
Use ID in RX and TX
6
Length of Packet
Enable
5
CRC Enable
4
Temperature
Compensation
3
[2:1]
0
Pull up Disable
POR State
Standby Mode
Data Sheet
Comment
1
Wake on ID in RX, send ID in TX
0
1
Enables the part to frame packets
0
1
Enables CRC (packet length must be enabled)
0
1
RF center frequency temperature compensation enabled
0
Temperature compensation is disabled
1
Pull ups on IIC clock and data and SSN pins disabled
0
Standby
Idle
RX
00
01
10
11
1
TX
Crystal only mode, system clock output active
0
Low-power standby mode
7.1.5. General Options B
General options B contains more option bits for the general setup and operation of the AMIS-53000.
System Clock Output Frequency: Sets the frequency of the output clock on the SYSclk pin when enabled.
RXTX Sampling Edge: Specifies which edge of DCLK should be used to sample the RXTX pin.
Auto Increment Disable: When enabled, a multiple address read or write command on the register interface will read/write
only the address given in the command multiple times.
Data Interface Clock Frequency: Sets the clock frequency for the data interface when the AMIS-53000 is configured to be
the master of the data interface. For modes in which the AMIS-53000 does not buffer the packet, the interface speed will
always be the data rate, regardless of this setting.
Data Interface Slave/Master: Specifies whether the AMIS-53000 is the master or slave for the data interface.
4-Wire Data Interface: Enables the 4-wire SPI data interface. When low, RXTX is bi-directional.
Table 89: General OptionsB - 0X0D [13]
Bit
Name
7
4-Wire Data Interface
6
Data Interface Slave/Master
5,4
Data Interface Clock Frequency
3
NU
2
RXTX Sampling Edge
1,0
System Clock Output
Frequency
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
State
Comment
1
Enabled
0
1
AMIS-53000 is slave
0
11
10
01
00
AMIS-53000 is master, clock speed determined by bits 5, 4
1MHz
500kHz
100kHz
Baud clock
1
Data bits are sampled on the rising edge of DCLK on the interface
0
Data bits are sampled on the falling edge of DCLK on the interface
11
12MHz (24MHz external crystal)
10
6MHz (24MHz external crystal)
01
3MHz (24MHz external crystal)
00
Off
79
AMIS-53000 Frequency Agile Transceiver
Data Sheet
7.1.6. Start of Frame
The start of frame byte is transmitted when this register is non-zero. It’s used as an aid for the receiver clock and data recovery circuit
in modes where the fast phase alignment feature is enabled.
Table 90: Start of Frame - 0X19 [25]
Bit
Name
Comment
7:0
SOF [7:0]
8-bit code sent prior to chip ID in TX and Burst
7.1.7. Data Rate 1
The data rate 1 and data rate 0 registers are used to set user defined data rates. These registers are loaded from ROM when a
discrete data rate is selected. The following equation is used to calculate the value for CUST_DR:
where DataRate is the desired data rate, and Fsample_clock is the frequency selected for the sample clock. This register is loaded with the
discrete rate if selected.
Table 91: Data Rate1 - 0X29 [41]
Bit
Name
Comment
7:0
CUST_DR [15:8]
Upper byte of user defined data rate/discrete data rate
7.1.8. Data Rate 0
Table 92: Data Rate0 - 0X2A [42]
Bit
Name
Comment
7:0
CUST_DR [7:0]
Lower byte of user defined data rate/discrete data rate
7.1.9. CRC Polynomial
This register allows a designer to change the CRC Polynomial used in the AMIS-53000. The register represents the presence of the
powers in the CRC equation. For example:
The Polynomial x8+x5+x2+x+1 is encoded by assuming the polynomial will always have a high order bit.
So the binary representation is: 1 0010 0111
This is set as the value 0X27 (HEX) in the register
(See “Koopman, P. & Chakravarty, T., “ Ccylic Redundancy Code (CRC) Polynomial Selection For Embedded Networks” DSN04, June
2004.” for more information.)
Table 93: CRC Poly - 0X30 [48]
Bit
Name
Comment
7:0
CRC_POLY [7:0]
CRC polynomial value
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
80
AMIS-53000 Frequency Agile Transceiver
Data Sheet
7.1.10. Default Length of Packet
This register allows a default value for the LOP (5 bytes) such that the AMIS-53000 does not have to send the LOP with a buffered
packet.
Table 94: Default LOP - 0X31 [49]
Bit
Name
Comment
7:0
DEFAULT_LOP [7:0]
Default value for the length of packet to be used in buffered TX/RX
7.1.11. Broadcast ID 1
Many applications in the wireless market make use of a broadcast function where the master note in a system can transmit to all
wireless nodes in the network without addressing each node individually, but still not broadcasting to nodes in another network.
Table 95: Broadcast ID1 - 0X3A [58]
Bit
Name
Comment
7:0
Global_ID1 [7:0]
Lower byte of the global address
7.1.12. Broadcast ID 0
Table 96: Broadcast ID0 - 0X3B [59]
Bit
Name
Comment
7:0
Global_ID0 [7:0]
Upper byte of the global address
7.2 TX/RX Data Interface Protocol
The AMIS-53000 TX/RX data format can be streaming data where the transmitter transmits each bit of data as it is received or it can be
packetized. Packetized data can be in packets up to 256 bytes. Packetized data can add a preamble, start of frame, identification
code, length of packet, and CRC error CheckSum.
Figure 44: Data Protocol Format
Streaming or packetized data
Buffer size is 256 byte maximum
Packet overhead
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
81
AMIS-53000 Frequency Agile Transceiver
Figure 45: 3-Wire Data Transfer Protocol
Figure 46: 4-Wire Data Transfer Protocol
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
82
Data Sheet
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Table 97: TX/RX Data Protocols
Modulation
Detector
CDR
Preamble
1
SOF
2
ID/LOP/CRC
Slice
AM
RSSI
Opt
CW
Yes
See Table 98
Fixed/Auto
FM (<20kbps)
PLL
Yes
1 0 pattern
-------
See Table 98
-------------
Yes
3
4
See Table 98
-------------
FM (>20kbps)
FFT
Notes:
1. The use of the CDR function to recover the data is recommended for AM/OOK modulation.
2. The SOF for AM modulation is suggested to be 55 (HEX) for NRZ and 0A (HEX) for Manchester encoded data.
3. The preamble for FM (FFT) with NRZ data is a 1 0 repeating pattern. The preamble for FM (FFT) with Manchester encoded data is all 1s or all 0s.
4. A SOF is only required for FM (FFT) when the data is Manchester encoded. The suggested SOF is a pattern of 55 (HEX) or AA (HEX).
Table 98: Interface Data Protocols
TX/RX Data Protocol
Interface Data
Protocol
Comments
LOP
CRC
Interface
Data
N
N
Active
Stream
N
N
Active*
Stream
* Data is streamed out the interface starting with the wakeup on ID
Y
N
Interrupt
Buffered
An interrupt is issued when data reception is complete
Y
Y
Interrupt
Buffered
An interrupt is issued when data reception is complete
1
Data is streamed out the interface as it is received
Notes:
1. When the interface uses streaming data, the AMIS-53000 must be the master.
The serial data interface for the AMIS-53000 can be configured to be a 3-wire interface or a 4-wire SPI interface. The AMIS-53000 can
be configured to act as a master or a slave for both receive and transmit operation. Bit 2 in the general options B register allows the
user to select whether DATA will be sampled on the rising, or falling edge of DCLK. The setting for the sampling polarity applies to all
modes.
Table 99: Serial Data Interface Configuration
General Options B
Bit 7
Bit 6
Data Port Configuration
Bit 2
# Port
Pins
AMIS-53000
Edge
Sample
Pin Function Definition
DCLK
DSSN
DRXTX
DOPT
0
0
X
3
Master
X
Output
Output
I/O
X
0
1
X
3
Slave
X
Input
Input
I/O
X
1
0
X
4
Master
X
Output
Output
Output
Input
1
1
X
4
Slave
X
Input
Input
Output
Input
X
X
0
X
X
Falling
X
X
1
X
X
Rising
7.2.1. AMIS-53000 in Master Mode
In receive mode, the DSSN pin will transition low when the AMIS-53000 has received data. Immediately following the transition of
DSSN, the AMIS-53000 will provide a synchronized bit clock on DCLK, and the received data will appear on DRXTX.
In transmit mode, the transition of DSSN is used to signal an external host/controller that the AMIS-53000 is ready for transmit data and
is ready to receive that data on the DRXTX pin. Immediately following the transition of DSSN, the AMIS-53000 will provide a
synchronous clock on DCLK for the host/controller to use for loading transmit data into the AMIS-53000.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
83
AMIS-53000 Frequency Agile Transceiver
Data Sheet
7.2.2. AMIS-53000 in Slave Mode
The AMIS-53000 cannot be the slave for streaming data. The requirements of adding header information such as preamble or SOF
requires that the AMIS-53000 be in control of the data interface transfer. The receiver has similar requirements with removing the
header information.
As the slave for the data interface, the AMIS-53000 will simply issue an interrupt to the external host indicating data is available after a
data packet has been received.
For buffered transmit operation, the AMIS-53000 will issue an interrupt indicating it is ready to load the packet. After the packet is
received by the AMIS-53000, the transmitter is enabled, any packet formatting is done and the packet is sent.
7.2.3. Manchester Operation
Figure 47: Manchester Coded Data
If the Manchester option is selected in the data rate and format register, the AMIS-53000 will internally encode and decode both
transmit and receive data respectively. The format for the signal interface remains NRZ in this mode.
7.2.4. Packet Framing
Three options bits located in the general options A register determine the method with which the transceiver will process packets: use
ID, length of packet (LOP) enable and cyclic redundancy check (CRC) enable. An additional bit in the TX config register enables the
buffered TX mode of operation.
Table 100: Register Configuration Bits
General Options A
TX Config
SOF
Bit 7
Bit 5
Bit 3
Bit 2
All
Bit 6
Use
0
X
X
X
X
X
1
X
X
X
X
X
ID
X
0
X
X
X
X
No LOP
No ID
1
1
X
X
X
X
LOP/ID
X
X
0
X
X
X
No CRC
1
1
1
X
X
X
CRC/ID/LOP
X
1
X
1
X
X
Buffer/LOP
X
X
X
0
X
X
No Buffer
X
X
X
X
0
X
Chip ID
X
X
X
X
1
X
Global ID
X
X
X
X
X
0x00
No SOF
?
X
X
X
X
All other
SOF
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
Comments
The ID must be enabled with LOP for data alignment
TX must have LOP enabled when using data buffering
Certain configurations require SOF to detect ID byte
84
AMIS-53000 Frequency Agile Transceiver
Data Sheet
7.2.5. Use ID
Table 101: ID
Register
Number (HEX)
Name
Bits
Function
0X0C
General Options A
7
Wake on ID in RX/send ID with TX
0X0F
TX Config
2
Select either the chip ID or global ID to be used in transmissions
0X16
Burst Config
3
Send ID with Burst packet
The chip ID is a 16 bit word which can be programmed in registers 3 and 4. In receive mode, when the use ID bit in general options A
is set, the AMIS-53000 will not begin exporting or buffering data until a valid ID matching the value stored in the chip address registers
is received. The ID is used in more advanced modes of operation for byte alignment. In addition to waking on its own unique ID, the
AMIS-53000 will also wake on a pre-defined global chip ID. The default value for the global ID is in the register table. This value can
be overwritten, but is not stored in EE so care must be taken when overwriting the value.
With the use ID bit enabled in transmit mode, the AMIS-53000 will transmit the chip ID prior to enabling the data interface. An
additional option bit in the TX config register allows selection of either the chip ID or global ID value for transmit.
In either transmit or receive, when the use ID bit is enabled without LOP enabled, the AMIS-53000 will not buffer data. Hence when
enabled stand alone, the data interface must be configured with the AMIS-53000 as the master.
7.2.6. Length of Packet Enable
The length of packet enable (LOP) bit located in general options A, enables the AMIS-53000 to buffer packets. The use ID bit must be
used in conjunction with LOP to allow the receiver to byte align on incoming data.
In receive mode with the LOP enabled, the AMIS-53000 will interpret the first byte following either a valid chip ID, or global ID to be the
length of the incoming packet. This byte specifies the number of bytes following the LOP to be received (non-inclusive of the CRC if
enabled). When enabled, the AMIS-53000 will buffer the incoming packet into internal RAM. Following reception of the last byte of the
packet, an interrupt is issued on the interrupt pin, and depending on the configuration of the data interface, the packet will either be sent
out of the data interface by the AMIS-53000 as master, or wait for the external host/controller to stream the packet out as the master.
Having the LOP enabled in transmit mode allows for the use of the buffered TX packet option in transmit, or the AMIS-53000 can still
act as master and process the packet on the fly. With LOP enabled, and buffered TX disabled, the AMIS-53000 must be the master for
the data interface. In this mode, the preamble and chip ID (or global ID) will be sent before the data interface is activated. Once the
DSSN is pulled low by the AMIS-53000, the first byte received into the part is expected to be the LOP byte. Transmission continues
until the AMIS-53000 has determined that all bytes have been received, at which point the data interface is disabled, and the AMIS53000 will return to standby. When buffered TX is enabled, after the transmit instruction is given to the AMIS-53000, an interrupt from
the AMIS-53000 will be issued indicating the part is ready to load in the data packet. The actual loading of the data packet depends on
the data interface setup as to whether the AMIS-53000 is master or slave. The first byte is again expected to be the LOP byte. After
the complete packet is loaded into the radio, the RF will be enabled, the preamble and chip ID transmitted, followed by the packet.
After completion of the transmission, the AMIS-53000 will return to standby.
7.2.7. CRC Enable
The CRC enable located in general options A is the final tier of intelligence for the AMIS-53000 packet handling capability. In order for
the AMIS-53000 to do CRC checking, this option must be used in conjunction with both use ID and LOP enable. Operation of the
interface for both receive and transmit with the CRC enabled is no different from that explained under the LOP enabled section. With
the CRC enabled, the AMIS-53000 will append the calculated CRC in transmit as the last byte. In receive mode, interrupts to the
external controller will only be issued for packets passing the CRC.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
85
AMIS-53000 Frequency Agile Transceiver
Data Sheet
7.2.8. SOF Byte
Table 102: Suggested SOF
Modulation
Detector
AM
RSSI
FM (<20kbps)
PLL
FM (>20kbps)
FFT
Coding
Preamble
SOF
NRZ
CW
55 (HEX)
Manchester
CW
0A (HEX)
1 0 pattern
1 0 pattern
Not required
NRZ
Repeating 1/0
Not required
Manchester
All 1’s or 0’s
55 (HEX) or AA (HEX)
Depending on whether the mode of operation is AM or FM, NRZ or Manchester, it may be necessary for a SOF byte to precede the
chip ID. This byte is user programmable, and is used to ensure proper CDR operation and bit alignment prior to reception of the chip
ID. When the contents of the SOF byte register are loaded to any non-zero value, this byte will be transmitted prior to the chip ID. For
modes not requiring the SOF byte, setting this register to 00h will prohibit transmission of this byte. More information on when the SOF
byte is required is in the clock and data recovery section.
7.2.9. Timing Diagrams for Various Packet Framing Modes
7.2.9.1.
Use ID Enabled, No CRC, No Packet Length
Table 103: Receive
Parameter Action
ID
Data interface immediately ready after ID detected
No LOP
Radio stays in RX until instructed to change
No CRC
Error checking is not performed and CRC is not attached to packet
Data is shifted out data port as received
Table 104: Transmit
Parameter Action
Transmit
Transmit command immediately powers the transmitter on
Transmits preamble
ID
Transmits the ID
Starts data interface and uses a synchronous clock to clock in the TX data (master only)
Transmits each bit as received
Transmitter returns to standby after transmission complete
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
86
AMIS-53000 Frequency Agile Transceiver
Figure 48: Data Interface Protocol (ID only)
7.2.9.2.
Use ID Enabled, No CRC, LOP Enabled
Table 105: Receive
Parameter
Action
ID
Data interface immediately ready after ID detected
LOP
Receiver loads rest of packet into buffer memory
After last data byte is received, radio returns to the previous state
An interrupt is issued to the external controller/microprocessor
Data is transferred out the port with the AMIS-53000 as master or the external controller as master
No CRC
Error checking is not performed and CRC is not attached to packet
Table 106: Transmit
Parameter
Action
Buffered
If buffered transmit is selected, the AMIS-53000 will open the data interface and transfer all TX data
Transmit
into memory with AMIS-53000 as master or external controller as master
Transmit
Transmit command (or end of TX data transfer) immediately powers the transmitter on
Transmits preamble (length of preamble as specified)
ID
Transmits the SOF and the ID
Starts data interface and uses a synchronous clock to clock in the TX data (master only)
or clocks data out of memory (buffered TX)
After the packet is transmitted, the transmitter returns to standby state
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
87
Data Sheet
AMIS-53000 Frequency Agile Transceiver
Data Sheet
Figure 49: Data Interface Protocol (ID and LOP)
7.2.9.3.
Use ID Enabled, CRC Enabled, LOP Enabled
Table 107: Receive
Parameter
Action
ID
Data interface immediately ready after ID detected
CRC
As soon as the ID is validated, the CRC starts processing the data
LOP
The LOP is received
CRC
Invalid
CRC Valid
The rest of the received data packet is buffered into memory
The last byte is the CRC and if invalid, the receiver waits for a command from the external host/controller, or if the receiver
came from idle it will return to receive
Receiver returns to previous state and an interrupt is issued to the external controller
The data interface is started and the data is sent to the controller, except for the CRC
Table 108: Transmit
Parameter
Transmit
Action
If buffered transmit is selected, the AMIS-53000 will open the data interface and transfer all TX data into memory with
AMIS-53000 as master or external controller as master
Transmit command (or end of TX data transfer) immediately powers the transmitter on
ID
Transmits the SOF and the ID
CRC
LOP
The CRC begins processing the data with the ID
Starts data interface and uses a synchronous clock to clock in the TX data (master only)
or clocks data out of memory (buffered TX)
The first byte is defined to be the LOP of the packet
CRC Byte
At the end of the packet, the data stops and the CRC value is sent
Buffered Transmit
Transmits preamble (length of preamble as specified)
After the packet is transmitted, the transmitter waits for a command from the external host/controller
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
88
AMIS-53000 Frequency Agile Transceiver
Figure 50: Data Interface Protocol (ID, LOP and CRC)
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
89
Data Sheet
AMIS-53000 Frequency Agile Transceiver
Data Sheet
8.0 General System Functions
8.1 Pull up Disable
2
The AMIS-53000 includes built in pull-up resistors for use with the I C operation to reduce the overall system component count. The
pull ups are asserted at POR until mode selection occurs. If mode is determined to be 3-wire, the pull ups are removed. If mode is
2
determined to be I C, this option bit determines whether the pull ups are to be removed.
2
Table 109: I C Pull Up Control
Register
Number (HEX)
Name
Bits
0X0C
General Options A
3
Function
2
Disable internal pull up resistors on I C bus
8.2 Brown-Out POR
The brown-out POR serves two purposes. The first is to provide a POR signal to reset the digital when power is initially applied to the
part. The second is to provide a POR should the voltage on the supply drift below normal operating range to prevent a brown-out
condition.
Table 110: Power-on-Reset Start Up State
Register
Number (HEX)
Name
Bits
Function
00 Standby
0X0C
General Options A
2,1
01 Idle
10 RX
11 TX
8.3 Temperature Sensor
o
The temperature sensor is created by using a Darlington pair of PNP transistors. The two transistors create a 5mV/ C slope that can
be sensed with an analog to digital converter. Without amplification, an 8 bit ADC with a 2V reference voltage will have a resolution
better than two degrees.
The temperature sensor can be trimmed to an accuracy of 3°C. As the trim is increased, the output voltage also increases.
The temperature voltage relationship is given by:
Where V is the output voltage and T is the temperature in Celsius.
Setup registers descriptions:
ADC Temperature- Register shows the value of the temperature sensor ADC. (See Section 6.13.1.1)
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
90
AMIS-53000 Frequency Agile Transceiver
Data Sheet
8.3.1. Crystal Temperature Compensation
An on-chip temperature sensor combined with an on-chip A/D and a look-up table enable the part to maintain RF frequency accuracy
within ± 2.5ppm over all operating voltages and temperatures (-45°C to 85°C). This function can be enabled via configuration bit 4
located in general options A. When this function is enabled, a new calculation for the center frequency word will be performed
whenever the temperature sensor storage register is updated with a new value. Therefore it is possible to update the compensation
value either in housekeeping, as part of a Burst transmit cycle, or as controlled externally by issuing the instruction to perform an ADC
measurement of the temp sensor.
Table 111: RF Frequency Temperature Compensation
Register
Function
Number (HEX)
Name
Bits
0X0C
General Options A
4
Enable RF frequency temperature compensation
8.4 Software
The version of the AMIS-53000 is written to a register at the end of the manufacturing process. This code can help AMIS wireless
product support when there is an issue with the AMIS-53000.
Setup registers descriptions:
AMIS ID- Register contains a code showing the version of the AMIS-53000.
8.4.1. AMIS Part Revision Code
Table 112: AMIS Part Revision Code - 0X41 [65]
Bit
Name
Comment
7:0
AMIS_ID [7:0]
Revision status of the AMIS-53000
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
91
AMIS-53000 Frequency Agile Transceiver
Data Sheet
9.0 Built-in Test Functions
The AMIS-53000 has a number of test registers. These registers are not available to the general user of the AMIS-53000. However,
many of these registers control test features that are useful in the development of applications using the AMIS-53000.
Setup registers descriptions:
Test Unlock- A special code is required to unlock the functions of the test registers.
Test- Registers that route signals to pins for monitoring or turn internal circuits off for test.
9.1 TM Unlock Register
The developer designing the AMIS-53000 may desire to use some of the test modes to monitor the operation of the AMIS-53000 or to
determine the activity of some parameter. These registers are locked from use by a code word. To unlock the test registers contact
AMIS wireless product support to obtain the code. Enter this code in the unlock register to access the test registers. This register will
be reset with a reset of the part and thus will lock the user out of the test registers.
Setup registers descriptions:
Test Unlock- Register contains a code about the state the AMIS-53000 is operating in.
** Registers with the ** mark can be trimmed if the test registers are unlocked.
Table 113: Test Unlock Code - 0X40 [64]
Bit
Name
Comment
Code to unlock operation of the test registers (contact AMIS for the code to unlock the test register
7:0
UNLOCK [7:0]
functions)
9.2 Test Registers
The following registers allow for signals to be routed to pins for monitoring. They also turn functions in the AMIS-53000 on and off for
measuring the operational parameters of the AMIS-53000.
9.2.1. IF Amp Manual Trim A
This register is used for factory testing of the AMIS-53000 and has no user functions.
9.2.2. IF Amp Manual Trim B
This register is used for factory testing of the AMIS-53000 and has no user functions.
9.2.3. PLL Manual Trim
This register is used for factory testing of the AMIS-53000 and has no user functions.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
92
AMIS-53000 Frequency Agile Transceiver
Data Sheet
9.2.4. PLL Test Modes
This register is used for factory testing of the AMIS-53000 and has no user functions.
9.2.5. Power Down RF Sections
This register is used for factory testing of the AMIS-53000 and has no user functions.
9.2.6. Analog Test Mode
Digital Pad Test: All digital pads except system clock out, and xInterrupt are 1mA I/O with pull ups and Schmitt triggers. The
SYSclock and xInterrupt pads are 2mA outputs.
2
Auto Increment Disable: This disables the automatic incrementing of the I C register addresses. It can allow repeated writes
to the same register, useful for adjusting a parameter to optimize its value.
Table 114: Analog Test Mode - 0X47 [71]
Bit Name
State
Comment
1
Enable the test mode for determination of capacitance trim value
7
CAP_TRIM
6
Pipe ADC1 to Data
Filter
1
Enable the ADC1 input channel as a direct input to the data filter
0
Normal operation
5
Brown-Out Power
Down
1
Override the brown-out POR to allow test at any voltage
4
Auto Increment
Disable
1
1
0
0
0
Ignore XTAL Control
Dig Pad Test A
1
Dig Pad Test B
Ignore crystal control (digital clock gating)
0
1
0
0
Address increment disabled (IIC only)
1
3
2
0
1
0
Enabled:
Input
SSSN
DClock
DSSN
xBurst
Disabled
Enabled:
Input
Doptional
xBurst
RXTX
Disabled
Enabled:
Corresponding output
Doptional
RXTX
xINT
sysClk
Enabled:
Corresponding output
SSSN
xINT
DSSN
9.2.7. RF Test Modes
This register is used for factory testing of the AMIS-53000 and has no user functions.
9.2.8. Analog Test MUX
This register is used for factory testing of the AMIS-53000 and has no user functions.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
93
AMIS-53000 Frequency Agile Transceiver
Data Sheet
9.2.9. RF Test MUX
This register is used for factory testing of the AMIS-53000 and has no user functions.
9.2.10. Digital Test MUX A
Table 115: Digital Test MUX A - 0X4B [75]
Bit
Test Pin
Comment
7:4
3:0
MUX to SCLK
MUX to Dopt
1111 - 0000
1111 - 0000
1111
Space Q channel CLK
0111
Energy dwell enable
1110
Mark Q channel CLK
0110
PLL increment
1101
NC
0101
TX enable
1100
0100
10kHz clock
1011
Data Q channel
PN code from Σ∆
0011
Software state [3]
1010
Start
0010
Bandgap ready
1001
Analog data out
0001
ADC CLK
1000
PLL detect/data out
0000
Normal/system clock
1111
Space I channel CLK
0111
Code dwell enable
1110
Mark I channel CLK
0110
PLL decrement
1101
PLL detect/NCO out
0101
Kicker
1100
Energy detected
0100
PLL Z
1011
Data I channel
0011
Software state [2]
1010
RF PLL CLK feedback
0010
PLL xReset
1001
Is locked (encoder)
0001
ADC power down
1000
TX data
0000
D optional
9.2.11. Digital Test MUX B
Table 116: Digital Test MUX B - 0X4C [76]
Bit
Test Pin
Comment
7:4
3:0
MUX to xINT
MUX to xBurst
1111 - 0000
1111- 0000
1111
Encoder in
0111
1110
Decoder in
0110
Cal done kicker
PLL in range
1101
Sniff
0101
INT0
1100
Σ∆ output
0100
Transmit done
1011
0011
Software state [1]
1010
RF PLL (reference
CLK)
Brown-out output
0010
Xtal on
1001
Receive done
0001
ADC done
1000
TS CLK
0000
xInterrupt
1111
Recovered clock
0111
1110
Decoder out
0110
1101
Encoder out
0101
PA enable
PLL cal timer
overflow
PLL cal enable
1100
CDR enable
0100
xtal PD
1011
Baud clock (CDR out)
0011
Software state [0]
isStopMode
1001
CRC failed
RX enable
0010
0001
1000
NC
0000
Watch dog reset
SSN normal mode
1010
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
94
AMIS-53000 Frequency Agile Transceiver
Data Sheet
9.2.12. Digital Test MUX C
Table 117: Digital Test MUX C - 0X4D [77]
Bit
Test Pin
Comment
1111
Encoder in
0111
RAMBist bad
1110
Decoder in
0110
EE BIST done
EE BIST good
0101
EE BIST bad
0100
Busy
0011
Instruction enable
Bandgap power down
1101
7:4
MUX to
Data SSN
3:0
1100
EE low voltage
detect
1111 - 0000
1011
1010
CPENA
ROM BIST done
0010
1001
ROM BIST bad
0001
1000
RAM BIST done
0000
1111- 0000
9.2.13. Digital Test Mode A
This register is used for factory testing of the AMIS-53000 and has no user functions.
9.2.14. Digital Test Mode B
This register is used for factory testing of the AMIS-53000 and has no user functions.
9.2.15. Digital Test Mode C
This register is used for factory testing of the AMIS-53000 and has no user functions.
9.2.16. Digital Test Mode D
This register is used for factory testing of the AMIS-53000 and has no user functions.
9.2.17. Memory Test Mode Address
This register is used for factory testing of the AMIS-53000 and has no user functions.
9.2.18. Memory Test Mode Data
This register is used for factory testing of the AMIS-53000 and has no user functions.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
95
XTAL
Data SSN normal
mode
AMIS-53000 Frequency Agile Transceiver
Data Sheet
10.0 Register Definition
Table 118 below contains the address for all of the internal registers. Once the EE has been written, the POR states for the registers
become the data last written. Should the CheckSum fail, all registers will return to the POR state shown, and an error flag will be
written to a status register.
Table 118: Register List
Address
R/W
Hex
Dec
Register Name
Description
POR State
EE
Section
R/W
0x00
0
Command
Instruction register
0000_0000
6.2
R/W
0x01
1
Status1
Part status, flags
0000_0000
6.4.5.1
R/W
0x02
2
Status2
Part status, flags
0000_0000
R/W
0x03
3
Chip Address 1
Upper 8 bits of chip address
0000_0000
X
7.1.1
R/W
0x04
4
Chip Address 0
Lower 8 bits of chip address
0000_0000
X
7.1.2
R/W
0x05
5
RF Divider
Integer portion of RF frequency
0000_0000
X
6.4.1.1
R/W
0x06
6
RF Frequency 2
Upper 8 bits of RF fraction
0000_0000
X
6.4.1.2
R/W
0x07
7
RF Frequency 1
Center 8 bits of RF fraction
0000_0000
X
6.4.1.3
R/W
0x08
8
RF Frequency 0
Lower 8 bits of RF fraction
0000_0000
X
6.4.1.4
R/W
0x09
9
Peak Deviation 1
Upper 8 bits of FM deviation
0000_0000
X
6.4.1.5
R/W
0X0A
10
Peak Deviation 0
Lower 8 bits of FM deviation
0000_0000
X
6.4.1.6
R/W
0x0B
11
Data Rate / Format
0000_0000
X
7.1.3
R/W
0x0C
12
General Options A
0000_0000
X
7.1.4
R/W
0x0D
13
General Options B
0000_0000
X
7.1.5
R/W
0x0E
14
RX Config
Set discrete data rate and encoding option
General options for interface, POR state,
etc.
General options for interface, POR state,
etc.
Receiver options
0000_0000
X
6.5.1.1
R/W
0x0F
15
TX Config
Transmit options
0000_0000
X
6.6.1
R/W
0x10
16
Idle Config
Idle mode options
X
6.7.1
R/W
0x11
17
Sniff Config
Sniff Mode options
1011_0100
X
6.7.2.1
R/W
0x12
18
Sniff Interval
Interval between Sniff cycles
0000_1010
X
6.7.2.2
R/W
0x13
19
Energy Dwell Time
0000_0000
X
6.7.2.3
R/W
0x14
20
Code Dwell Timer
0000_0000
X
6.5.1.5
R/W
0x15
21
Energy Threshold
0000_0000
X
6.5.1.2
R/W
0x16
22
Burst Config
Length of time to dwell in Sniff Mode
Number of bit times to wait for code
after energy
Threshold for wake on RSSI, Sniff
and CCA
Burst transmit options
0000_0000
X
6.7.3
R/W
0x17
23
Burst Interval
Interval timer for burst transmit
0001_1000
X
6.7.3.1
R/W
0x18
24
Output Power
Output power
0001_0000
X
6.6.2
R/W
0x19
25
Start of Frame
0001_0000
X
7.1.6
R/W
0x1A
26
Preamble Length
0001_0000
X
6.6.3
R/W
0x1B
27
HK Config
Byte used for burst transmit/CDR wake up
Length of CW, or ‘10’
repeated in Burst/TX (BT’s)
Housekeeping options register
R/W
0x1C
28
HK Interval
R/W
0x1D
29
Slice Threshold
6.4.5.2
X
6.7.4.1
X
6.7.4.2
X
6.5.1.4
X
6.5.1.4
R/W
0x1E
30
Filter/Slice
Interval timer for housekeeping
Energy threshold for AM DAC mode
data slice
AM/RSSI filter setting and AM slice mode
R/W
0x1F
31
CDR Options A
Clock and data recovery options A
R/W
0x20
32
CDR Options B
Clock and data recovery options B
R/W
0x21
33
Crystal Trim
Crystal trim
0000_0000
X
6.10.1.1
R/W
0x22
34
LNA Trim
LNA input and output matching trim
0000_0000
X
6.10.1.2
R/W
0x23
35
Quick Start Trim
Quick Start oscillator trim
0000_0000
X
6.10.1.3
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
96
X
6.5.1.5
1000_0000
X
6.5.1.5
AMIS-53000 Frequency Agile Transceiver
Table 118: Register List (Continued)
Address
R/W
Register Name
Hex
Dec
R/W
0x24
36
10k Osc Trim
0x25
37
Analog Trim
0x26
38
Analog Trim 2
0x27
39
RF PLL Trim
0x28
40
RF PLL Options
0x29
41
Data Rate 1
0x2A
42
Data Rate 0
0x2B
43
PLL Loop Co
0x2C
44
CDR Loop Co
0x2D
45
User Data
0x2E
46
User Data
0x2F
47
TargNumWakeUps
0x30
48
CRCPoly
0x31
49
DefaultLOP
0x32
50
Checksum
0x33
51
0x34
52
Temp ADC
0x35
0x36
0x37
0x38
0x39
0x3A
0x3B
0x3C
0x3D
0x3E
0x3F
0x40
0x41
0x42
0x43
0x44
0x45
0x46
0x47
0x48
0x49
0x4A
0x4B
0x4C
0x4D
0x4E
0x4F
0x50
0x51
0x52
0x53
0x54
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
Battery ADC
RSSI ADC
EXT1 ADC
EXT2 ADC
Loop Filter
Global Chip ID1
Global Chip ID0
Software State
Unlock Reg
AMIS ID Code
IF Amp Trim A
IF Amp Trim B
Manual PLL Trim
PLL Test Mode
PDtestRF
Analog Test Mode
RFTM
Analog Test Mux
RF Test Mux
Digital Test Mux A
Digital Test Mux B
Digital Test Mux C
DTM A
DTM B
DTM C
DTM D
MTM Address
MTM Data
PLLCalTarget
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
Data Sheet
Description
POR State
EE
Section
10kHz oscillator trim
Bandgap and temp sensor trim
Capacitance trim
PLL calibration storage register
RF PLL options register
User defined data rate upper bits
User defined data rate lower bits
User defined PLL detector bandwidth
User defined clock recovery loop
Transmitted on normal interval burst
Transmitted on interrupt triggered Burst
Target number of wake ups for
CRC polynomial register
Default LOP register
EEPROM checksum
0000_0000
0000_0000
0010_0100
0100_0100
0000_0000
0000_0000
0000_0000
0000_0000
0000_0000
0000_0000
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
6.10.1.4
6.10.1.5
6.10.1.6
6.10.1.7
6.4.1.7
7.1.7
7.1.8
6.5.1.4
6.5.1.5
6.7.3.2
6.7.3.3
6.7.2.4
7.1.9
7.1.10
6.9.1
Storage register for the temp sensor
reading
0000_0000
6.13.1.1
Storage register for the battery reading
Storage register for the RSSI reading
Storage register for the EXT1 input
Storage register for the EXT2 input
0000_0000
0000_0000
0000_0000
0000_0000
6.13.1.2
6.13.1.3
6.13.1.4
6.13.1.5
6.4.1.8
7.1.11
7.1.12
6.4.5.3
1010_0101
0011_0001
9.1
8.4.1
9.2.1
9.2.2
9.2.3
9.2.4
9.2.5
9.2.6
9.2.7
9.2.8
9.2.9
9.2.10
9.2.11
9.2.12
9.2.13
9.2.14
9.2.15
9.2.16
9.2.17
9.2.18
6.10.1.8
0000_0000
0000_0000
0000_0000
0000_0000
0000_0000
0000_0000
PLL calibration target value
97
0000_0000
AMIS-53000 Frequency Agile Transceiver
11.0 Applications
This section intentionally left blank.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
98
Data Sheet
AMIS-53000 Frequency Agile Transceiver
Data Sheet
12.0 Ordering Information
Table 119: Ordering Information
Ordering Code
Product Name
Package
Type
Operating
Temperatu
re Range
19608-001-XTP (or –XTD)
AMIS-53000-I/A
32 LQFP
-40C to 85C
19608-002-XTP (or –XTD)
AMIS-53000-I/A
32 LQFP
-40C to 85C
19637-001-XTP (or –XTD)
AMIS-53000-M
32 LQFP
-40C to 85C
19637-002-XTP (or –XTD)
AMIS-53000-M
32 LQFP
-40C to 85C
Industry
Application
Differentiating
Feature
Industrial,
Automotive,
Other
Industrial,
Automotive,
Other
Medical
Extra Low Power
Medical
SPI Interface;
Ganged
Transceivers
Extra Low Power
SPI Interface;
Ganged
Transceivers
Shipping
Configuration
Tape & Reel (-XTP);
Tubes (-XTD)
Tape & Reel (-XTP);
Tubes (-XTD)
Tape & Reel (-XTP);
Tubes (-XTD)
Tape & Reel (-XTP);
Tubes (-XTD)
13.0 Company or Product Inquiries
For more information about AMI Semiconductor, our technology and our products, visit our Web site at: http://www.amis.com.
North America
Tel: +1.208.233.4690
Fax: +1.208.234.6795
Europe
Tel: +32 (0) 55.33.22.11
Fax: +32 (0) 55.31.81.12
Devices sold by AMIS are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. AMIS makes no warranty, express, statutory,
implied or by description, regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. AMIS makes no warranty of
merchantability or fitness for any purposes. AMIS reserves the right to discontinue production and change specifications and prices at any time and without notice. AMI
Semiconductor's products are intended for use in commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high
reliability applications, such as military, medical life-support or life-sustaining equipment, are specifically not recommended without additional processing by AMIS for such
applications. Copyright ©2005 AMI Semiconductor, Inc.
AMI Semiconductor – Aug. 05, Rev. 1.0
www.amis.com
99