BXF200 Series Single output DC/DC CONVERTERS • • • • • • • • • 72-132W Wide Input DC/DC Converters 1 Board mounted full brick with industry standard footprint Adjustable output voltage with output currents of 40A No minimum load required 2:1 input range for battery powered applications Synchronizable and parallelable with load sharing Overtemperature and short circuit protection Current monitor and power good signal Remote ON/OFF ISO9001 certified manufacturing facilities BXF200 Series high power density DC/DC converters can provide up to 40A output current and have an industry-standard footprint, measuring just 2.40 x 4.60 x 0.52 inches. The converters are equally suitable for new designs or as replacement power sources in existing equipment. BXF200 Series converters are designed specifically for redundant and distributed power systems in the computer and telecommunications sectors, but their feature-rich specifications make them suitable for a very wide range of applications. Using Bellcore 332, the MTBF is over 1,000,000 hours. Aluminium baseplate technology and four threaded M3 inserts make heatsink attachment and thermal management easy. The BXF200 Series is approved by UL, CSA and VDE. 2 YEAR WARRANTY SPECIFICATIONS All specifications are typical at nominal input, full load at 25°C unless otherwise stated OUTPUT SPECIFICATIONS EMC CHARACTERISTICS Voltage adjustability Model specific Set point accuracy ±0.5% typ., ±1.6% max. Line regulation Low line to high line ±0.1% typ. Load regulation Full load to min. load ±0.15% typ. Minimum load 0A Overshoot 0V Undershoot At turn-on and turn-off 0V Ripple and noise 5Hz to 20MHz (See Note 1) Temperature coefficient Transient response 20mV rms ±0.01%/°C Recovery time (See Note 2) Peak deviation Remote sense 500µs 2.0% 0.5VDC transmission line drop compensation INPUT SPECIFICATIONS Conducted emissions (See Note 8) 48VDC nominal Input current No load Remote OFF 65mA max. 15mA max. Input current (max.) (See Note 3) See table Input reflected ripple (See Note 5) 11mA pk-pk Active low remote ON/OFF Logic compatibility ON OFF Undervoltage lockout 48Vin: power up 48Vin: power down Start-up time (See Note 6) Power up Remote ON/OFF Level A Level A Level A GENERAL SPECIFICATIONS Efficiency See table Isolation voltage Input/case Input/output Output/case Switching frequency Fixed Approvals and standards (See Note 4) VDE0805, EN60950, IEC950 UL1950, CSA C22.2 No. 950 Aluminium baseplate and plastic casing Material flammability UL94V-0 Weight 36 to 75VDC 1500VDC 1500VDC 1500VDC 550kHz typ. Case material MTBF Input voltage range Bellcore 332 FCC part 15 EN55022, CISPR22 200g (7.06oz) Bellcore 332 MIL-HDBK-217F @ 40°C, 100% FL >1,000,000 hours >200,000 hours ENVIRONMENTAL SPECIFICATIONS Thermal performance Operating case temp. -40°C to +100°C Non-operating -55°C to +125°C (See Note 7) Altitude Operating Non-operating 1.2VDC max. Open circuit Vibration 5Hz to 500Hz 10,000 feet max. 40,000 feet max. 2.4G rms (approx.) 35V typ. 33V typ. 2.5ms typ. 1ms typ. File Name: BXF200.PDF Rev: 10 Jan 2001 BXF200 Series Single output DC/DC CONVERTERS 72-132W Wide Input DC/DC Converters 2 For the most current data and application support visit www.artesyn.com/powergroup/products.htm OUTPUT POWER (MAX.) INPUT VOLTAGE OVP OUTPUT VOLTAGE INPUT CURRENT (MAX.) OUTPUT CURRENT (MAX.) EFFICIENCY (TYP.) LINE LOAD MODEL NUMBER (7) 100W 36 to 75VDC 3.2VDC 2.5V 4.4A 40A 76% ±0.10% ±0.15% BXF200-48S2V5L 80W 72W 36 to 75VDC 2.5VDC 2.0V 3.7A 40A 72% ±0.10% ±0.15% BXF200-48S2V0L 36 to 75VDC 2.3VDC 1.8V 3.4A 40A 70% ±0.10% ±0.15% BXF200-48S1V8L Notes 1 2 3 4 5 6 7 8 REGULATION PROTECTION Measured with 10µF tantalum capacitor and 1µF ceramic capacitor across the output. Iout = Inom; delta Iout = ±25% Iout (max), di/dt = 1A/µs. Input fusing is required based on surge and maximum input current. This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. Input reflected ripple current test set-up uses a Pi filter; 220µF, 12µH, 100µF. Start-up into resistive load. Active high remote on/off is available (standard product is active low), designate with the suffix ‘H’ e.g. BXF200-48S2V5H. Units should be characterised within systems. External components and filtering required. PIN CONNECTIONS Short circuit protection Continuous, automatic recovery Overvoltage protection Latching Thermal protection 110°C baseplate, automatic recovery TELECOM SPECIFICATION Central office interface A ETS300-132-2 EXTERNAL OUTPUT TRIMMING PIN NUMBER FEATURE 1 Power Good 2 Current Monitor 3 Parallel 4 Trim Adjust 5 + Sense 6 - Sense Output can be externally trimmed by using the method shown. 5 TRIM UP 4 TRIM DOWN RT1 OR RT2 6 International Safety Standard Approvals VDE0805/EN60950/IEC950 File No. 10401-3336-0148 UL1950 File No. E136005 CSA C22.2 No. 950 File No. LR41062C Please consult our website for the following items: ✔ Application Note www.artesyn.com File Name: BXF200.PDF Rev: 10 Jan 2001 BXF200 Series Single output DC/DC CONVERTERS 72-132W Wide Input DC/DC Converters 3 For the most current data and application support visit www.artesyn.com/powergroup/products.htm Mechanical Notes 1 2 3 All dimensions in INCHES (mm). Tolerance: x.xx ±0.02in. (0.51mm). x.xxx ±0.010in. (0.254mm). All pins are tin/lead plated brass. TOP VIEW WITH OVERALL DIMENSIONS THREADED INSERTS M3 x 0.5 THROUGH 4 PLACES 2.40 2.00 (61.0) (50.8) 4.20 (106.7) 4.60 (116.8) SIDE VIEW 0.53 (13.5) 0.00 (0.0) 0.20 (5.1) MIN. 2.600 (66.04) 0.040 ± 0.002 (1.02 ± 0.05) DIA. 3 PLACES BOTTOM VIEW PIN DETAILS 0.062 ± 0.002 (1.57 ± 0.05) DIA. 11 PLACES 2 4 6 1 CASE 3 5 S2 S1 PRI ENABLE VINVIN+ 0.040 ± 0.002 (1.02 ± 0.05) DIA. 6 PLACES VOUTVOUTVOUTVOUTVOUT+ VOUT+ VOUT+ VOUT+ BOTTOM VIEW DIMENSIONAL DETAILS 1.70 (43.2) 1.50 (38.1) 2 4 6 0.100 (2.54) 1.20 (30.48) 0.900 (22.86) 0.700 (17.78) 0.500 (12.70) 0.300 (7.62) 1.50 (38.1) 1 3 5 0.100 (2.54) 5 PLACES 0.200 (5.08) 7 PLACES 0.000 (0.00) 0.000 (0.00) 0.500 (12.70) 0.70 (17.8) 0.50 (12.7) 0.000 (0.00) 0.20 (5.1) 2.600 (66.04) 4.20 (106.7) 4.40 (111.8) Data Sheet © Artesyn Technologies® 2002 The information and specifications contained in this data sheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. Please consult our website for the following items: ✔ Application Note www.artesyn.com File Name: BXF200.PDF Rev: 10 Jan 2001