LOG114 SBOS301A − MAY 2004 − REVISED MARCH 2007 Single-Supply, High-Speed, Precision LOGARITHMIC AMPLIFIER FEATURES DESCRIPTION D ADVANTAGES: The LOG114 is specifically designed for measuring low-level and wide dynamic range currents in communications, lasers, medical, and industrial systems. The device computes the logarithm or log-ratio of an input current or voltage relative to a reference current or voltage (logarithmic transimpedance amplifier). D D D D D D D D − Tiny for High Density Systems − Precision on One Supply − Fast Over Eight Decades − Fully-Tested Function TWO SCALING AMPLIFIERS WIDE INPUT DYNAMIC RANGE: Eight Decades, 100pA to 10mA 2.5V REFERENCE STABLE OVER TEMPERATURE LOW QUIESCENT CURRENT: 10mA DUAL OR SINGLE SUPPLY: +5V, +5V PACKAGE: Small QFN-16 (4mm x 4mm) SPECIFIED TEMPERATURE RANGE: −5°C to +75°C High precision is ensured over a wide dynamic range of input signals on either bipolar (±5V) or single (+5V) supply. Special temperature drift compensation circuitry is included on-chip. In log-ratio applications, the signal current may be from a high impedance source such as a photodiode or resistor in series with a low impedance voltage source. The reference current is provided by a resistor in series with a precision internal voltage reference, photo diode, or active current source. APPLICATIONS D ONET ERBIUM-DOPED FIBER OPTIC AMPLIFIER (EDFA) LASER OPTICAL DENSITY MEASUREMENT PHOTODIODE SIGNAL COMPRESSION AMP D D D LOG, LOG-RATIO FUNCTION D ANALOG SIGNAL COMPRESSION IN FRONT D OF ANALOG-TO-DIGITAL (ADC) CONVERTER ABSORBANCE MEASUREMENT The output signal at VLOGOUT has a scale factor of 0.375V out per decade of input current, which limits the output so that it fits within a 5V or 10V range. The output can be scaled and offset with one of the available additional amplifiers, so it matches a wide variety of ADC input ranges. Stable dc performance allows accurate measurement of low-level signals over a wide temperature range. The LOG114 is specified over a −5°C to +75°C temperature range and can operate from −40°C to +85°C. R5 V LOGOUT 9 (2) R6 10 +IN 4 11 −IN 4 LOG114 Q1 200Ω R (1) I1 4 V CM IN 1250Ω R2 1 A1 A4 5 I1 and I 2 are current inputs from a photodiode or other current source VO4(3) A 3(4) Q2 13 200Ω R (1) I2 3 IREF 12 1250Ω R4 3 A5 A2 15 +IN 5 VO5 R REF 16 REF VREF 2.5V 1 V REF GND 8 V+ 6 7 V− Com 14 − IN 5 NOTES: (1) Thermally dependent R 1 and R 3 provide temperature compensation. (2) V LOGOUT = 0.375 × log(I1/I2). (3) V O4 = 0.375 × K × log(I1/I2) K = 1 + R 6/R 5. (4) Differential Amplifier (A3 ) Gain = 6.25 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. Copyright 2004−2007, Texas Instruments Incorporated ! ! www.ti.com "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ABSOLUTE MAXIMUM RATINGS(1) Supply Voltage, V+ to V− . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V Signal Input Terminals, Voltage(2) . . . . . (V−) −0.5V to (V+) + 0.5V Current(2) . . . . . . . . . . . . . . . . . . . . ±10mA Output Short-Circuit(3) . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous Operating Temperature . . . . . . . . . . . . . . . . . . . . . . −40°C to +85°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . −55°C to +125°C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C ESD Rating (Human Body Model) . . . . . . . . . . . . . . . . . . . . 2000V (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. (2) Input terminals are diode-clamped to the power-supply rails. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PRECISION CURRENT MEASUREMENT PRODUCTS Input signals that can swing more than 0.5V beyond the supply rails should be current-limited to 10mA or less. (3) Short-circuit to ground. FEATURES PRODUCT Logarithmic Transimpedance Amplifier, 5V, Eight Decades LOG114 Logarithmic Transimpedance, 36V, 7.5 Decades LOG112 Resistor-Feedback Transimpedance, 5V, 5.5 Decades OPA380, OPA381 Switched Integrator Transimpedance, Six Decades IVC102 Direct Digital Converter, Six Decades DDC112 ORDERING INFORMATION(1) PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR LOG114 QFN-16 RGV PACKAGE MARKING LOG114 (1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. PIN CONFIGURATION QFN-16 VO5 −IN5 +IN5 16 15 14 13 1 3 I1 4 10 +IN4 9 5 6 7 8 V+ I2 11 −IN4 Com 2 V− NC 12 VO4 Exposed thermal die pad on underside (Must be connected to V−) VCM IN VREF GND VREF Top View QFN−16 (4mm x 4mm) NC = No Connection 2 VLOGOUT "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 ELECTRICAL CHARACTERISTICS: VS = +5V Boldface limits apply over the specified temperature range, TA = −5°C to +75°C. All specifications at TA = +25°C, RVLOGOUT = 10kΩ, VCM = GND, unless otherwise noted. LOG114 PARAMETER CONDITIONS CORE LOG FUNCTION MIN IIN/VOUT Equation TYP MAX VO = (0.375V) Log (I1/I2) UNITS V LOG CONFORMITY ERROR(1) Initial 1nA to 100µA (5 decades) 100pA to 3.5mA (7.5 decades) 0.1 0.2 % 0.009 0.017 dB 0.9 % 0.08 dB 1mA to 10mA See Typical Characteristics 1nA to 100µA (5 decades) 0.1 100pA to 3.5mA (7.5 decades) 0.5 % 1mA to 10mA See Typical Characteristics % Initial Scaling Factor 100pA to 10mA 0.375 Scaling Factor Error 1nA to 100µA 0.4 ±2.5 % 0.035 0.21 dB Over Temperature 0.4 % TRANSFER FUNCTION (GAIN)(2) Over Temperature V/decade TMIN to TMAX 1.5 ±3.5 % +15°C to +50°C 0.7 ±3 % ±1 ±4 INPUT, A1 and A2 Offset Voltage VOS vs Temperature dV/dT TMIN to TMAX +15 vs Power Supply PSRR VS = ±2.25V to ±5.5V 75 Input Bias Current IB vs Temperature Input Common-Mode Voltage Range Voltage Noise Current Noise in µV/V pA Doubles every 10°C VCM en 400 ±5 TMIN to TMAX mV µV/°C (V−)+1.5 to (V+)−1.5 V f = 0.1Hz to 10kHz 3 µVrms f = 1kHz 30 nV/√Hz f = 1kHz 4 fA/√Hz ±11 ±50 mV TMIN to TMAX ±15 ±65 mV OUTPUT, A3 (VLOGOUT) Output Offset, VOSO, Initial VOSO Over Temperature Full-Scale Output (FSO)(3) Gain Bandwidth Product Short-Circuit Current (V−) + 0.6 GBW IIN = 1µA ISC Capacitive Load (V+) − 0.6 V 50 MHz ±18 mA 100 pF OP AMP, A4 and A5 Input Offset Voltage ±250 VOS ±1000 µV dV/dT TMIN to TMAX ±2 vs Supply PSRR VS = ±4.5V to ±5.5V 30 vs Common-Mode Voltage CMRR 74 dB IB −1 µA vs Temperature Input Bias Current Input Offset Current 250 ±0.05 IOS Input Voltage Range (V−) Input Noise f = 0.1Hz to 10Hz f = 1kHz Current Noise µV/°C in µV/V µA (V+) − 2 V 2 µVPP 13 nV/√Hz 2 pA/√Hz Open-Loop Voltage Gain AOL 100 dB Gain Bandwidth Product GBW 15 MHz 5 V/µs Slew Rate Settling Time 0.01% SR tS Rated Output Short-Circuit Current G = −1, 3V Step, CL = 100pF (V−) + 0.5 ISC µs 1.5 (V+) − 0.5 +4/−10 V mA 3 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 ELECTRICAL CHARACTERISTICS: VS = +5V (continued) Boldface limits apply over the specified temperature range, TA = −5°C to +75°C. All specifications at TA = +25°C, RVLOGOUT = 10kΩ, VCM = GND, unless otherwise noted. LOG114 PARAMETER CONDITIONS MIN TOTAL ERROR(4, 5) TYP MAX UNITS See Typical Characteristics FREQUENCY RESPONSE, Core Log(6) BW, 3dB I1 or I2 = IAC = 10% of IDC value, IREF = 1µA 1nA 5 kHz 10nA 12 kHz 100nA 120 kHz 1µA 2.3 MHz 10µA to 1mA (ratio 1:100) >5 MHz 1mA to 3.5mA (ratio 1:3.5) >5 MHz 3.5mA to 10mA (ratio 1:2.9) >5 MHz 8nA to 240nA (ratio 1:30) 0.7 µs 10nA to 100nA (ratio 1:10) 1.5 µs 10nA to 1µA (ratio 1:100) 0.15 µs 10nA to 10µA (ratio 1:1k) 0.07 µs 10nA to 1mA (ratio 1:100k) 0.06 µs 1 µs 8nA to 240nA (ratio 1:30) 1 µs 10nA to 100nA (ratio 1:10) 2 µs 10nA to 1µA (ratio 1:100) 0.25 µs 10nA to 10µA (ratio 1:1k) 0.05 µs 10nA to 1mA (ratio 1:100k) 0.03 µs 1 µs Step Response IREF = 1µA Increasing (I1 or I2) 1mA to 10mA (ratio 1:10) Decreasing (I1 or I2) IREF = 1µA 1mA to 10mA (ratio 1:10) VOLTAGE REFERENCE Bandgap Voltage 2.5 ±0.15 Error, Initial V ±1 ±25 vs Temperature vs Supply vs Load % ppm/°C VS = ±4.5V to ±5.5V ±30 ppm/V IO = ±2mA ±200 ppm/mA ±10 mA Short-Circuit Current POWER SUPPLY Dual Supply Operating Range Quiescent Current ±2.4 VS IQ ±10 IO = 0 ±5.5 V ±15 mA TEMPERATURE RANGE Specification, TMIN to TMAX −5 +75 °C Operating −40 +85 °C Storage −55 +125 Thermal Resistance, qJA 62 °C °C/W (1) Log conformity error is peak deviation from the best-fit straight line of VO vs Log (I1/I2) curve expressed as a percent of peak-to-peak full-scale output. Scale factor, K, equals 0.375V output per decade of input current. (2) Scale factor of core log function is trimmed to 0.375V output per decade change of input current. (3) Specified by design. (4) Worst-case total error for any ratio of I1/I2, as the largest of the two errors, when I, and I2 are considered separately. (5) Total error includes offset voltage, bias current, gain, and log conformity. (6) Small signal bandwidth (3dB) and transient response are a function of the level of input current. Smaller input current amplitude results in lower bandwidth. 4 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 ELECTRICAL CHARACTERISTICS: VS = +5V Boldface limits apply over the specified temperature range, TA = −5°C to +75°C. All specifications at TA = +25°C, RVLOGOUT = 10kΩ, VCM = +2.5V, unless otherwise noted. LOG114 PARAMETER CONDITIONS CORE LOG FUNCTION IIN/VOUT Equation MIN TYP MAX VO = (0.375V) Log (I1/I2) + VCM UNITS V LOG CONFORMITY ERROR(1) Initial 1nA to 100µA (5 decades) 100pA to 3.5mA (7.5 decades) 0.1 0.25 % 0.009 0.022 dB 0.9 % 0.08 dB 1mA to 10mA See Typical Characteristics 1nA to 100µA (5 decades) 0.1 100pA to 3.5mA (7.5 decades) 0.5 1mA to 10mA See Typical Characteristics Initial Scaling Factor 10nA to 100µA 0.375 Scaling Factor Error 1nA to 100µA 0.4 ±2.5 % 0.0.35 0.21 dB Over Temperature 0.4 % % TRANSFER FUNCTION (GAIN)(2) Over Temperature V/decade TMIN to TMAX 0.035 ±3.5 % +15°C to +50°C 0.7 ±3 % ±1 ±7 INPUT, A1 and A2 Offset Voltage VOS mV vs Temperature dV/dT TMIN to TMAX +30 µV/°C vs Power Supply PSRR VS = +4.5V to +5.5V 300 µV/V Input Bias Current IB ±5 pA vs Temperature Input Common-Mode Voltage Range Voltage Noise Current Noise TMIN to TMAX Doubles every 10°C VCM en in (V−)+1.5 to (V+)−1.5 V f = 0.1Hz to 10kHz 3 µVrms f = 1kHz 30 nV/√Hz f = 1kHz 4 fA/√Hz OUTPUT, A3 (VLOGOUT) Output Offset, VOSO, Initial VOSO Over Temperature TMIN to TMAX Full Scale Output (FSO)(3) Gain Bandwidth Product Short-Circuit Current VS = +5V GBW ±14 ±65 mV ±18 ±80 mV (V−) + 0.6 IIN = 1µA ISC Capacitive Load (V+) − 0.6 V 50 MHz ±18 mA 100 pF OP AMP, A4 and A5 Input Offset Voltage ±250 VOS ±4000 µV dV/dT TMIN to TMAX ±2 µV/°C vs Supply PSRR VS = +4.8V to +5.5V 30 µV/V vs Common-Mode Voltage CMRR 70 dB IB −1 µA vs Temperature Input Bias Current Input Offset Current ±0.05 IOS Input Voltage Range (V−) Input Noise f = 0.1Hz to 10Hz in V 28 µVPP nV/√Hz 2 pA/√Hz 1 f = 1kHz Current Noise µA (V+) − 1.5 Open-Loop Voltage Gain AOL 100 dB Gain Bandwidth Product GBW 15 MHz 5 V/µs Slew Rate Settling Time 0.01% SR tS Rated Output Short-Circuit Current G = −1, 3V Step, CL = 100pF (V−) + 0.5 ISC µs 1.5 (V+) − 0.5 +4/−10 V mA 5 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 ELECTRICAL CHARACTERISTICS: VS = +5V (continued) Boldface limits apply over the specified temperature range, TA = −5°C to +75°C. All specifications at TA = +25°C, RVLOGOUT = 10kΩ, VCM = +2.5V, unless otherwise noted. LOG114 PARAMETER CONDITIONS MIN TOTAL ERROR(4, 5) TYP MAX UNITS See Typical Characteristics FREQUENCY RESPONSE, Core Log(6) BW, 3dB I1 or I2 = IAC = 10% of IDC value, IREF = 1µA 1nA 5 kHz 10nA 12 kHz 100nA 120 kHz 1µA 2.3 MHz 10µA to 1mA (ratio 1:100) >5 MHz 1mA to 3.5mA (ratio 1:3.5) >5 MHz 3.5mA to 10mA (ratio 1:2.9) >5 MHz 8nA to 240nA (ratio 1:30) 0.7 µs 10nA to 100nA (ratio 1:10) 1.5 µs 10nA to 1µA (ratio 1:100) 0.15 µs 10nA to 10µA (ratio 1:1k) 0.07 µs 10nA to 1mA (ratio 1:100k) 0.06 µs 1 µs 8nA to 240nA (ratio 1:30) 1 µs 10nA to 100nA (ratio 1:10) 2 µs 10nA to 1µA (ratio 1:100) 0.25 µs 10nA to 10µA (ratio 1:1k) 0.05 µs 10nA to 1mA (ratio 1:100k) 0.03 µs 1 µs Step Response IREF = 1µA Increasing (I1 or I2) 1mA to 10mA (ratio 1:10) Decreasing (I1 or I2) IREF = 1µA 1mA to 10mA (ratio 1:10) VOLTAGE REFERENCE Bandgap Voltage 2.5 ±0.15 Error, Initial V ±1 ±25 vs Temperature vs Supply vs Load % ppm/°C VS = +4.8V to +11V ±30 ppm/V IO = ±2mA ±200 ppm/mA ±10 mA Short-Circuit Current POWER SUPPLY Single Supply Operating Range Quiescent Current VS IQ 4.8 ±10 IO = 0 11 V ±15 mA TEMPERATURE RANGE Specification, TMIN to TMAX −5 +75 °C Operating −40 +85 °C Storage −55 +125 Thermal Resistance, qJA 62 °C °C/W (1) Log conformity error is peak deviation from the best-fit straight line of VO vs Log (I1/I2) curve expressed as a percent of peak-to-peak full-scale output. Scale factor, K, equals 0.375V output per decade of input current. (2) Scale factor of core log function is trimmed to 0.375V output per decade change of input current. (3) Specified by design. (4) Worst-case total error for any ratio of I1/I2, as the largest of the two errors, when I, and I2 are considered separately. (5) Total error includes offset voltage, bias current, gain, and log conformity. (6) Small signal bandwidth (3dB) and transient response are a function of the level of input current. Smaller input current amplitude results in lower bandwidth. 6 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 TYPICAL CHARACTERISTICS: VS = +5V All specifications at TA = +25°C, RVLOGOUT = 10kΩ, VCM = GND, unless otherwise noted. ONE CYCLE OF NORMALIZED TRANSFER FUNCTION 0.40 1.5 0.35 Normalized Output Voltage (V) Normalized Output Voltage (V) NORMALIZED TRANSFER FUNCTION 2.0 1.0 0.5 0 −0.5 −1.0 −1.5 −2.0 10−4 10−3 10−2 10−1 0.30 0.25 0.20 0.15 0.10 0.05 0 1 101 102 103 104 1 10 Current Ratio (I1/I2) 40 Current Ratio (I 1/ I2) SCALING FACTOR ERROR (I2 = reference 100pA to 10mA) VLOGOUT vs I 1 INPUT (I2 = 1µA) 2.5 2.0 1.5 1.0 20 10 +70_ C VLOGOUT (V) Gain Error (%) 30 +25_ C 0_ C 0 −10 −20 0.5 0 −0.5 −1.0 −10_ C −1.5 +80_ C +90_ C 100pA 1nA −2.0 −2.5 10nA 100nA 1µA 10µA 100µA 1mA 10mA 100pA 1nA 10nA 100nA 1µA Input Current (I1) 2.0 VLOGOUT vs I2 INPUT (I1 = 1µA) 10mA VLOGOUT vs I REF 4 100pA 1.5 3 1.0 1nA 10nA 2 1µA 0.5 VLOGOUT (V) VLOGOUT (V) 10µA 100µA 1mA Input Current (I1) 0 −0.5 −1.0 100nA 1 0 −1 10µA −2 −1.5 −2.0 −3 −2.5 100pA 1nA −4 100pA 1nA 10nA 100nA 1µA 10µA 100µA 1mA Input Current (I1) 10mA 1mA 100µA 10mA 10nA 100nA 1µA 10µA 100µA 1mA 10mA IREF (I2) 7 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 TYPICAL CHARACTERISTICS: VS = +5V (continued) All specifications at TA = +25°C, RVLOGOUT = 10kΩ, VCM = GND, unless otherwise noted. AVERAGE TOTAL ERROR AT +80_C 100 80 80 60 60 I1 = 1mA 40 20 I1 = 10µA I = 100µA 1 0 −20 −40 20 −100 I1 = 100µA 0 −40 −60 I1 = 10nA I1 = 1nA 100µA 200µA I 1 = 100nA 400µA 600µA I 1 = 1µA −80 I1 = 1µA 1mA 100µA 400µA 200µA AVERAGE TOTAL ERROR AT −10_C LOG CONFORMITY vs TEMPERATURE 7.5 Decade I1 = 1mA 40 I1 = 1nA 20 0 I1 = 10nA −40 I1 = 100µA 1.0 Linearity (%) Total Error (mV) 1mA 1.2 I1 = 1µA −80 0.8 7 Decade 0.6 5 Decade 4 Decade 6 Decade 0.4 I1 = 10µA I = 100nA 1 −60 0.2 −100 0 100µA 200µA 400µA 600µA 800µA −10 1mA 0 10 I2 0.40 0.35 0.08 +90_ C Linearity (%) 0_C −10_ C +80_ C 40 50 60 70 80 90 5 DECADE LOG CONFORMITY vs I REF +90_ C 0.25 0.20 +80_ C 0.15 +70_ C 0.10 0.05 +25_C +70_ C 0.04 100pA 1nA 30 0.30 0.07 0.06 20 Temperature (_ C) 4 DECADE LOG CONFORMITY vs IREF 0.09 Linearity (%) 800µA 1.4 60 10nA 100nA 1µA IREF (I1) 8 600µA I2 80 −20 I1 = 1nA, 10nA, 100nA −100 800µA I2 100 I 1 = 10µA −20 −60 −80 I1 = 1mA 40 Total Error (mV) Total Error (mV) AVERAGE TOTAL ERROR AT +25_C 100 10µA 100µA 1mA 0.05 10mA −10_C, 0_ C, +25_C 0 100pA 1nA 10nA 100nA 1µA I REF (I1) 10µA 100µA 1mA 10mA "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 TYPICAL CHARACTERISTICS: VS = +5V (continued) All specifications at TA = +25°C, RVLOGOUT = 10kΩ, VCM = GND, unless otherwise noted. For ac measurements, small signal means up to approximately 10% of dc level. 6 DECADE LOG CONFORMITY vs IREF 0.45 8 DECADE LOG CONFORMITY (100pA to 3.5mA) 1.6 1.5 0.40 +90_ C 1.4 Linearity (%) 0.35 +80_C 0.30 +70_C 1.3 1.2 0_ C 0.25 −10_C, 0_ C, +25_ C +70_ C 0.9 100pA 1nA 10nA 100nA 1µA 20 10µA 100µA 1mA 100pA 1nA 10mA 10nA 100nA 1µA 10µA 100µA 1mA IREF (I1) Input Current (I1 or I 2) SMALL−SIGNAL VLOGOUT SMALL−SIGNAL AC RESPONSE I1 (10% sine modulation) −5 Normalized LOG Output (dB) 10 1µA 1mA 0 100nA −10 10mA 0 10mA Normalized VLOGOUT (%) −10_ C 1.0 0.20 10nA −20 100µA −30 10µA 10µA −10 100µA −15 −20 1µA 1nA −25 −30 1mA 100nA 10nA −35 −40 −45 −40 −50 10 100 1k 10k 100k 1M 10M 100M 100 1k 10k Frequency (Hz) 160 −5 140 10µA 10M 100M 225 120 100µA −15 180 1µA 1nA −25 Gain (dB) 100 −20 1mA 10nA −30 100nA −35 80 135 60 Phase Gain 40 90 20 −40 0 −45 −20 45 −40 −50 100 1M A3 GAIN AND PHASE vs FREQUENCY 0 −10 100k Frequency (Hz) SMALL−SIGNAL AC RESPONSE I2 (10% sine modulation) Normalized LOG Output (dB) +25_C +80_ C 1.1 Phase (_ ) Linearity (%) +90_C 1k 10k 100k 1M Frequency (Hz) 10M 100M 100 1k 10k 100k 1M 10M 0 40M Frequency (Hz) 9 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 TYPICAL CHARACTERISTICS: VS = +5V (continued) All specifications at TA = +25°C, RVLOGOUT = 10kΩ, VCM = GND, unless otherwise noted. A4 and A5 GAIN AND PHASE vs FREQUENCY 180 140 3 120 Phase Gain 90 60 40 Phase (_) 80 45 20 Normalized Output (dB) 0 135 100 Gain (dB) A4 and A5 NONINVERTING CLOSED−LOOP RESPONSE 0 −20 1 10 100 1k 10k 100k 1M 10M G=1 −3 G = 10 −6 −9 −12 −15 0 18M 1k 10k A4 and A5 INVERTING CLOSED−LOOP RESPONSE 30 1M 10M 100M A4 and A5 CAPACITIVE LOAD RESPONSE 10 G = +1 20 0 10 0 −10 −10 G = −10 −20 Gain (dB) Gain (dB) 100k Frequency (Hz) Frequency (Hz) G = −1 −30 −40 C = 100pF −20 C < 10pF −30 −50 −60 −40 −70 −80 −50 1k 10k 100k 1M Frequency (Hz) 10 10M 60M 1k 10k 100k 1M Frequency (Hz) 10M 50M "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 Either I1 or I2 can be held constant to serve as the reference current, with the other input being used for the input signal. The value of the reference current is selected such that the output at VLOGOUT (pin 9) is zero when the reference current and input current are equal. An onchip 2.5V reference is provided for use in generating the reference current. APPLICATIONS INFORMATION OVERVIEW The LOG114 is a precision logarithmic amplifier that is capable of measuring currents over a dynamic range of eight decades. It computes the logarithm, or log ratio, of an input current relative to a reference current according to equation (1). V LOGOUT + 0.375 log 10 Two additional amplifiers, A4 and A5, are included in the LOG114 for use in scaling, offsetting, filtering, threshold detection, or other functions. ǒII Ǔ 1 BASIC CONNECTIONS 2 (1) The output at VLOGOUT can be digitized directly, or scaled for an ADC input using an uncommitted or external op amp. Figure 1 and Figure 2 show the LOG114 in typical dual and single-supply configurations, respectively. To reduce the influence of lead inductance of power-supply lines, it is recommended that each supply be bypassed with a 10µF tantalum capacitor in parallel with a 1000pF ceramic capacitor as shown in Figure 1 and Figure 2. Connecting these capacitors as close to the LOG114 V+ supply pin to ground as possible improves supply− related noise rejection. An offsetting voltage (VCom) can be connected to the Com pin to raise the voltage at VLOGOUT. When an offsetting voltage is used, the transfer function becomes: V LOGOUT + 0.375 log 10 ǒII Ǔ ) V 1 Com (2) 2 R8 56.2kΩ R7 100kΩ R5 100kΩ 9 VLOGOUT(1) Q1 IREF 1µF 4 I1 5 VCM IN Input Signal RREF 100pA to 10mA 2.5MΩ R1 10 R6 66.5kΩ 11 +IN4 −IN4 R2 A1 A4 Q2 A3 3 I2 R3 R4 A5 A2 16 VREF LOG114 VO4(2) 12 +IN5 13 VO5 15 2.5VREF VREF GND 1 V+ 8 V− 1000pF 10µF 6 1000pF 10µF + +5V + Com 7 −IN5 14 NOTE: (1) VLOGOUT = 0.375 × log(I1/I2) (2) VO4 = −0.249 × log(I1/I2) + 1.5V −5V Figure 1. Dual Supply Configuration Example for Best Accuracy Over Eight Decades. 11 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 R6 66.5kΩ R5 100kΩ R7 100kΩ R8 316kΩ REF3040 or REF3240 4.096V Reference Input current from photodiode or current source Q1 I1 IµA RREF 1.62MΩ 9 VLOGOUT(2) 4 I1 5 VCM IN(1) R1 3 11 −IN4 R2 A4 A3 I2 R4 R3 A5 A2 Photodiode(4) +2.5V 16 VREF 2.5VREF VREF GND 1 V −IN5 V− Com 8 + 1000pF 6 7 1 10µF VCom = +2.5V +5V NOTE: (1) (2) (3) (4) In single−supply configuration, VCM IN must be connected to ≥ 1V. VLOGOUT = 0.375 × log(I1/I2) + 2.5V. VO4 = −0.249 × log(I 1/I2) + 1.5V. The cathode of the photodiode is returned to VREF resulting in zero bias across it. The cathode could be returned to a voltage more positive than VCM IN to create a reverse bias for reducing photodiode capacitance, which increases speed. Figure 2. Single-Supply Configuration Example for Measurement Over Eight Decades. 12 LOG114 A1 Q2 I2 10 +IN4 VO4(3) 12 +IN5 13 VO5 15 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 4. The A4 amplifier scales and offsets the VLOGOUT signal for use by the ADC using the equation: DESIGN EXAMPLE FOR DUAL-SUPPLY CONFIGURATION Given these conditions: D V+ = 5V and V− = −5V D 100pA ≤ Input signal D The stage following the LOG114 is an analog-todigital converter (ADC) with +5V supply and +2.5V reference voltage, so VO4 swings from +0.5V to +2.5V. 1. Due to LOG114 symmetry, you can choose either I1 or I2 as the signal input pin. Choosing I1 as the reference makes the resistor network around A4 simpler. (Note: Current must flow into pins 3 (I1) and pin 4 (I2).) 2. Select the magnitude of the reference current. Since the signal (I2) spans eight decades, set I1 to 1µA − four decades above the minimum I2 value. (Note that it does not have to be placed in the middle. If I2 spanned seven decades, I1 could be set three decades above the minimum and four decades below the maximum I2 value.) This configuration results in more swing amplitude in the negative direction, which provides more sensitivity (∆VO4 per ∆I2) when the current signal decreases. VLOGOUT + 0.375 Therefore, choose the final A4 output: 0V ≤ VO4 ≤ +2.5V This output results in a 2.5V range for the 3V VLOGOUT range, or 2.5V/3V scaling factor. 5. When I2 = 10mA, VLOGOUT = −1.5V. Using the equation in step 5: V O4 + *SFACTOR + 0.375 The A4 amplifier configuration for VO4 = −2.5/3(VLOGOUT) + 0V is seen in Figure 3. The overall transer function is: V O4 + *0.249 + 0.375 ǒ log Ǔ 1mA 100pA (7) Internal A4 Output Amplifier R6 82.5kΩ +5V VO4 = −2/3 (VLOGOUT) A4 I1 I2 VREF +2.5V + ) 1.5V (3) Therefore, the expected voltage range at the output of amplifier A3 is: * 1.5V v V LOGOUT v ) 1.5V 1 VLOGOUT I1 I2 ǒǓ log ǒII Ǔ ) 1.5V log 2 1mA ǒ10mA Ǔ + * 1.5V VLOGOUT + 0.375 (6) Therefore, VOFFSET = 0V log For I2 + 100pA : ǒVLOGOUTǓ ) VOFFSET 0V + *2.5Vń3V(*1.5V) ) VOFFSET R5 100kΩ ǒǓ log (5) The A4 amplifier is specified with a rated output swing capability from (V−) +0.5V to (V+) − 0.5V. 3. Using Equation (1) calculate the expected range of log outputs at VLOGOUT: For I2 + 10mA : ǒVLOGOUTǓ ) VOFFSET V O4 + *SFACTOR (4) −5V R7 100kΩ R8 37.4kΩ 10mA I2 100pA VO4 0V +2.5V A4 amplifier used to scale and offset VLOGOUT for 0V to 2.5V output. Figure 3. Operational Amplifier Configuration for Scaling the Output Going to ADC Stage. 13 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 This result would be fine in a dual−supply system (V+ = +5V, V− = −5V) where the output can swing below ground, but does not work in a single supply +5V system. Therefore, an offset voltage must be added to the system. DESIGN EXAMPLE FOR SINGLE-SUPPLY CONFIGURATION Given these conditions: D D D D V+ = 5V V− = GND 100pA ≤ Input signal ≤ 10mA The stage following the LOG114 is an analog to digital converter (ADC) with +5V supply and +2.5V reference voltage 1. Choose either I1 or I2 as the signal input pin. For this example, I2 is used. Choosing I1 as the reference current makes the resistor network around A4 simpler. (Note: Current only flows into the I1 and I2 pins.) 2. Select the magnitude of the reference current. Since the signal (I2) spans eight decades, set I1 to 1µA − four decades above the minimum I2 value, and four decades below the maximum I2 value. (Note that it does not have to be placed in the middle. If I2 spanned seven decades, I1 could be set three decades above the minimum and four decades below the maximum I2 value.) This configuration results in more swing amplitude in the negative direction, which provides more sensitivity (∆VO4 per ∆I2) when the current signal decreases. 3. Using Equation (1) calculate the expected range of log outputs at VLOGOUT: + 0.375 ǒǓ log 1mA ǒ10mA Ǔ + * 1.5V For I2 + 100pA : + 0.375 ǒ log 5. The A4 amplifier scales and offsets the VLOGOUT signal for use by the ADC using the equation: ǒVLOGOUTǓ ) VOFFSET V O4 + *SFACTOR (11) The A4 amplifier is specified with a rated output swing capability from (V−) +0.5V to (V+) − 0.5V. Therefore, choose the final A4 output: +0.5V ≤ VO4 ≤ +2.5V This output results in a 2V range for the 3V VLOGOUT range, or 2V/3V scaling factor. 6. When I2 = 10mA, VLOGOUT = +1V, and VO4 = 2.5V. Using the equation in step 5: V O4 + *SFACTOR ǒVLOGOUTǓ ) VOFFSET 2.5V + *2Vń3V(1V) ) VOFFSET (12) The overall transer function is: V O4 + *0.249 ǒǓ I1 log I2 Ǔ 1mA 100pA + ) 1.5V * 1.5V v V LOGOUT v ) 1.5V ǒII Ǔ ) 1.5V log 1 (13) A similar process can be used for configuring an external rail-to-rail output op amp, such as the OPA335. Because the OPA335 op amp can swing down to 0V using a pulldown resistor, RP, connected to −5V (for details, refer to the OPA335 data sheet, available for download at www.ti.com), the scaling factor is 2.5V/3V and the corresponding VOFFSET is 3.3V. This circuit configuration is shown in Figure 4b. 2 (8) Therefore, the expected voltage range at the output of amplifier A3 is: 14 (10) The A4 amplifier configuration for VO4 = −2/3(VLOGOUT) + 3.16 is seen in Figure 4a. I1 I2 log VLOGOUT + 0.375 ) 1V v V LOGOUT v ) 4V Therefore, VOFFSET = 3.16V For I2 + 10mA : VLOGOUT + 0.375 4. Select an offset voltage, VCom to use for centering the output between (V−) + 0.6V and (V+) − 0.6V, which is the full-scale output capability of the A3 amplifier. Choosing VCom = 2.5V, and recalculating the expected voltage output range for VLOGOUT using Equation (2), results in: (9) "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 Internal A4 Output Amplifier R5 100kΩ External Output Amplifier R5 100kΩ R6 66.5kΩ R6 82.5kΩ VLOGOUT VLOGOUT +5V A4 VO4 = −2/3 (VLOGOUT) + 3.16 10mA I2 VREF +2.5V 100pA R7 100kΩ R8 316kΩ VOUT = −2.5/3 (VLOGOUT) + 3.3 OPA335 VREF +2.5V 2.5V VO4 RP(1) 10mA I2 100pA −5V R7 100kΩ R8 267kΩ VOUT 0.5V 2.5V 0.5V a) A4 amplifier used to scale and offset VLOGOUT for 0.5V to 2.5V output. b) OPA335 amplifier used to scale and offset VLOGOUT for 0V to 2.5V output. NOTE: (1) See OPA335 data sheet for use of RP connected to −5V to achieve 0V output. Figure 4. Operational Amplifier Configuration for Scaling and Offsetting the Output Going to ADC Stage. ADVANTAGES OF DUAL−SUPPLY OPERATION VCM IN (Pin 5) The LOG114 performs very well on a single +5V supply by level-shifting pin 7 (Com) to half-supply and raising the common-mode voltage (pin 5, VCM IN) of the input amplifiers. This level−shift places the input amplifiers in the linear operating range. However, there are also some advantages to operating the LOG114 on dual ±5V supplies. These advantages include: The VCM IN pin is used to bias the A1 and A2 amplifier into its common-mode input voltage range, (V−) + 1.5V to (V+) − 1.5V. 1) eliminating the need for the +4.096V precision reference; 2) eliminating a small additional source of error arising from the noise and temperature drift of the level−shifting voltage; and INPUT CURRENT RANGE To maintain specified accuracy, the input current range of the LOG114 should be limited from 100pA to 3.5mA. Input currents outside of this range may compromise the LOG114 performance. Input currents larger than 3.5mA result in increased nonlinearity. An absolute maximum input current rating of 10mA is included to prevent excessive power dissipation that may damage the input transistor. 3) allowing increased magnitude of a reverse bias voltage on the photodiode. COM (PIN 7) VOLTAGE RANGE The voltage on the Com pin is used to bias the differential amplifier, A3, within its linear range. This voltage can provide an asymmetrical offset of the VLOGOUT voltage. 15 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 SETTING THE REFERENCE CURRENT When the LOG114 is used to compute logarithms, either I1 or I2 can be held constant to become the reference current to which the other is compared. ply system, and a maximum value of 7mV in a +5V supply system. Resistor temperature stability and noise contributions should also be considered. If IREF is set to the lowest current in the span of the signal current (as shown in the front page figure), VLOGOUT will range from: V LOGOUT + 0.375 log 10 ǒI maxI minsignalǓ ^ 0V VREF = 100mV 1 1 R1 (14) R3 1 +5V to some maximum value: V LOGOUT + 0.375 log 10 ǒ R2 Ǔ I 1 min I 1 max signal (15) A better way to achieve higher accuracy is to choose IREF to be in the center of the full signal range. For example, for a signal range of 1nA to 1mA, it is better to use this approach: Ǹ1mAń1nA + 1mA dc A1 IREF R3 >> R2 While convenient, this approach does not usually result in best performance, because I1 min accuracy is difficult to achieve, particularly if it is < 20nA. I REF + I SIGNAL min VOS − + Figure 5. T-Network for Reference Current. VREF may be an external precision voltage reference, or the on-chip 2.5V voltage reference of the LOG114. IREF can be derived from an external current source, such as that shown in Figure 6. (16) than it is to set IREF = 1nA. It is much easier and more precise (that is, dc accuracy, temperature stability, and lower noise) to establish a 1mA dc current level than a 1nA level for the reference current. IREF 2N2905 The reference current may be derived from a voltage source with one or more resistors. When a single resistor is used, the value may be large depending on IREF. If IREF is 10nA and +2.5V is used: RREF = 2.5V/10nA = 250MΩ A voltage divider may be used to reduce the value of the resistor, as shown in Figure 5. When using this method, one must consider the possible errors caused by the amplifier input offset voltage. The input offset voltage of amplifier A1 has a maximum value of 4mV in a ±5V sup- 16 RREF 3.6kΩ 2N2905 +15V 6V IN834 −15V IREF = 6V RREF Figure 6. Temperature-Compensated Current Source. "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 NEGATIVE INPUT CURRENTS The LOG114 functions only with positive input currents (conventional current flows into input current pins). In QA I IN situations where negative input currents are needed, the example circuits in Figure 7, Figure 8, and Figure 9 may be used. QB National LM394 D1 D2 OPA703 IOUT Figure 7. Current Inverter/Current Source. +5V +3.3V 1/2 OPA2335 1.5kΩ 1kΩ 10nA to 1mA (+3.3V Back Bias) +5V BSH203 1/2 OPA2335 10nA to 1mA Pin 3 or Pin 4 LOG114 Photodiode Figure 8. Precision Current Inverter/Current Source. 1kΩ 100kΩ 100kΩ +5V 10nA to 1mA +3.3V Back Bias 1/2 OPA2335 +5V 1.5kΩ +3.3V 1/2 OPA2335 Photodiode 1.5kΩ 100kΩ 100kΩ LOG114 10nA to 1mA Pin 3 or Pin 4 Figure 9. Precision Current Inverter/Current Source. 17 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 VOLTAGE INPUTS noise from these sources must be considered and can limit the usefulness of this technique. The LOG114 provides the best performance with current inputs. Voltage inputs may be handled directly by using a low-impedance voltage source with series resistors, but the dynamic input range is limited to approximately three decades of input voltage. This limitation exists because of the magnitude of the required input voltage and size of the corresponding series resistor. For 10nA of input current, a 10V voltage source and a 1GΩ resistor would be required. Voltage and current APPLICATION CIRCUITS LOG RATIO One of the more common uses of log ratio amplifiers is to measure absorbance. See Figure 10 for a typical application. Absorbance of the sample is A = log λ1′/λ1. If D1 and D2 are matched, A ∝ (0.375V) log(I1/I2). R5 9 V LOGOUT(1) Q1 I1 Sample λ1 I1 5 V CM IN R1 +IN 4 A3 I2 R4 R3 A5 A2 D2 16 LO G114 R2 Q2 3 10 − IN 4 A4 λ 1′ λ1 10 A1 D1 I2 Light Source 4 R6 V REF V O4(2) 12 +IN 5 13 V O5 15 2.5V REF V REF GND 1 V+ 8 V− 6 Com − IN 5 7 14 +5V NO TES: (1) V LOGOUT = 0.375 × log(I1/I 2). (2) V O4 = 0.375 × K × log(I1/I 2) K = 1 + R 6/R 5. Figure 10. Using the LOG114 to Measure Absorbance. 18 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 DATA COMPRESSION In many applications, the compressive effects of the logarithmic transfer function are useful. For example, a LOG114 preceding a 12-bit ADC can produce the dynamic range equivalent to a 20-bit converter. (Suggested products: ADS7818, ADS7834). I1 LOG114 VLOGOUT I2 V+ +3.3V OPERATION V− TPS60241 For systems with only a +3.3V power supply, the TPS60241 zero-ripple switched cap buck-boost 2.7V to 5.5V input to 5V output converter may be used to generate a +5V supply for the LOG114, as shown in Figure 11. +3.3V C1 1µF C1 1µF VIN VOUT C1+ C2+ C1− C2− GND EN +5V C2 1µF C0 1µF Likewise, the TPS6040 negative charge pump may be connected to the +5V output of the TPS60241 to generate a −5V supply to create a ±5V supply for the LOG114, as Figure 12 illustrates. Figure 11. Creating a +5V Supply from a +3.3V Supply. I1 VLOGOUT LOG114 I2 V+ +5V V− −5V CFLY 1µF TPS60241 C1 1µF CFLY− CFLY+ +5V +3.3V C1 1µF VIN VOUT C1+ C2+ C1− C2− GND EN IN C2 1µF CO 1µF CI 1µF TPS60400 GND OUT −5V CO 1µF Figure 12. Creating a ±5V Supply from a +3.3V Supply. 19 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 An alternate design of the system shown in Figure 13 is possible because the LOG114 inherently takes the log ratio. Therefore, one log amp can be eliminated by connecting one of the photodiodes to the LOG114 I1 input, and the other to the I2 input. The differential amplifier would then be eliminated. ERBIUM-DOPED FIBER OPTIC AMPLIFIER (EDFA) The LOG114 was designed for optical networking systems. Figure 13 shows a block diagram of the LOG114 in a typical EDFA application. This application uses two log amps to measure the optical input and output power of the amplifier. A difference amplifier subtracts the log output signals of both log amps and applies an error voltage to the proportional-integral-derivative (PID) controller. The controller output adjusts a voltage-controlled current source (VCCS), which then drives the power op amp and pump laser. The desired optical gain is achieved when the error voltage at the PID is zero. The log ratio function is the optical power gain of the EDFA. This circuitry forms an automatic power level control loop. The LOG114 is uniquely suited for most EDFA applications because of its fast rise and fall times (typically less than 1µs for a 100:1 current input step). It also measures a very wide dynamic range of up to eight decades. Tap Tap 1% 1% Fiber Pump Laser OPA569 IL Power Op Amp VCCS PID VERROR Diff I1 LOG114 IREF1 VOUT1 VOUT2 I2 LOG114 REF IREF2 DAC RREF1 RREF2 Figure 13. Erbium-Doped Fiber Optic Amplifier (EDFA) block diagram. 20 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 INSIDE THE LOG114 The LOG114 uses two matched logarithmic amplifiers (A1 and A2 with logging diodes in the feedback loops) to generate the outputs log (I1) and log (I2), respectively. The gain of 6.25 differential amplifier (A3) subtracts the output of A2 from the output of A1, resulting in [log (I1) − log (I2)], or log (I1/I2). The symmetrical design of the A1 and A2 logarithmic amps allows I1 and I2 to be used interchangeably, and provides good bandwidth and phase characteristics with frequency. Log conformity is defined as the peak deviation from the best fit straight line of the VLOGOUT versus log (I1/I2) curve. Log conformity is then expressed as a percent of ideal full−scale output. Thus, the nonlinearity error expressed in volts over m decades is: DEFINITION OF TERMS Transfer Function The ideal transfer function of the LOG114 is: V LOGOUT + 0.375 VLOGOUT (NONLIN) = 0.375V/decade • 2Nm ǒǓ I log 1 12 where N is the log conformity error, in percent. (17) This transfer function can be seen graphically in the typical characteristic curve, VLOGOUT vs IREF. When a pedestal, or offset, voltage (VCom) is connected to the Com pin, an additional offset term is introduced into the equation: V LOGOUT + 0.375 ǒ1I Ǔ ) V log 1 2 Log Conformity For the LOG114, log conformity is calculated in the same way as linearity and is plotted as I1/I2 on a semilog scale. In many applications, log conformity is the most important specification. This condition is true because bias current errors are negligible (5pA for the LOG114), and the scale factor and offset errors may be trimmed to zero or removed by system calibration. These factors leave log conformity as the major source of error. Com (18) Accuracy Accuracy considerations for a log ratio amplifier are somewhat more complicated than for other amplifiers. This complexity exists because the transfer function is nonlinear and has two inputs, each of which can vary over a wide dynamic range. The accuracy for any combination of inputs is determined from the total error specification. Total Error The total error is the deviation of the actual output from the ideal output. Thus, VLOGOUT(ACTUAL) = VLOGOUT(IDEAL) ± Total Error It represents the sum of all the individual components of error normally associated with the log amp when operating in the current input mode. The worst-case error for any given ratio of I1/I2 is the largest of the two errors when I1 and I2 are considered separately. Temperature can also affect total error. Errors RTO and RTI As with any transfer function, errors generated by the function may be Referred-to-Output (RTO) or Referredto-Input (RTI). In this respect, log amps have a unique property: given some error voltage at the log amp output, that error corresponds to a constant percent of the input, regardless of the actual input level. INDIVIDUAL ERROR COMPONENTS The ideal transfer function with current input is: V LOGOUT IDEAL ǒ1I Ǔ + 0.375 log 1 (19) The actual transfer function with the major components of error is: 2 0.375(1 " DK) ǒII Ǔ " 2Nm " V log 1 OSO 2 (20) where: ∆K = gain error (0.4%, typ, as specified in the Electrical Characteristics table) IB1 = bias current of A1 (5pA, typ) IB2 = bias current of A2 (5pA, typ) m = number of decades over which the log conformity error is specified N = log conformity error (0.1%, typ for m = 5 decades; 0.9% typ for m = 7.5 decades) VOSO = output offset voltage (11mV, typ for ±5V supplies; 14mV, typ for +5V supplies) To determine the typical error resulting from these error components, first compute the ideal output. Then calculate the output again, this time including the individual error components. Then determine the error in percent using Equation (21): %error + ŤV LOGOUT IDEAL*V LOGOUT TYPŤ V LOGOUTIDEAL 100% (21) 21 "#$$% www.ti.com SBOS301A − MAY 2004 − REVISED MARCH 2007 For example, in a system configured for measurement of five decades, with I1 = 1mA, and I2 = 10µA: V LOGOUT VLOGOUT IDEAL + 0.375 ǒ + 0.375(1 " 0.004) TYP Ǔ *3 log 10*5 + 0.75V 10 ǒ1010 log −3*5 −5*5 (22) Ǔ 10−12 10−12 The exposed leadframe die pad on the bottom of the package should be connected to V−. " 2(0.001)(5) " 0.011 (23) Using the positive error components (+∆K, +2Nm, and +VOSO) to calculate the maximum typical output: V LOGOUT TYP + 0.774V (24) Therefore, the error in percent is: %error + |0.75*0.774| 0.75 100% + 3.2% (25) QFN PACKAGE The LOG114 comes in a QFN-16 package. This leadless package has lead contacts on all four sides of the bottom of the package, thereby maximizing board space. An exposed leadframe die pad on the bottom of the package enhances thermal and electrical characteristics. QFN packages are physically small, have a smaller routing area, improved thermal performance, and improved electrical parasitics. Additionally, the absence of external leads eliminates bent-lead issues. 22 The QFN package can be easily mounted using standard printed circuit board (PCB) assembly techniques. See Application Note QFN/SON PCB Attachment (SLUA271) and Application Report Quad Flatpack No− Lead Logic Packages (SCBA017), both available for download at www.ti.com. QFN LAYOUT GUIDELINES The exposed leadframe die pad on the QFN package should be soldered to a thermal pad on the PCB. A mechanical drawing showing an example layout is attached at the end of this data sheet. Refinements to this layout may be necessary based on assembly process requirements. Mechanical drawings located at the end of this data sheet list the physical dimensions for the package and pad. The five holes in the landing pattern are optional, and are intended for use with thermal vias that connect the leadframe die pad to the heatsink area on the PCB. Soldering the exposed pad significantly improves board-level reliability during temperature cycling, key push, package shear, and similar board-level tests. Even with applications that have low-power dissipation, the exposed pad must be soldered to the PCB to provide structural integrity and long-term reliability. PACKAGE OPTION ADDENDUM www.ti.com 7-May-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty LOG114AIRGVR ACTIVE QFN RGV 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR LOG114AIRGVRG4 ACTIVE QFN RGV 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR LOG114AIRGVT ACTIVE QFN RGV 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR LOG114AIRGVTG4 ACTIVE QFN RGV 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 17-May-2007 TAPE AND REEL INFORMATION Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com Device 17-May-2007 Package Pins Site Reel Diameter (mm) Reel Width (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LOG114AIRGVR RGV 16 MLA 330 12 4.3 4.3 1.5 12 12 PKGORN T2TR-MS P LOG114AIRGVT RGV 16 MLA 180 12 4.3 4.3 1.5 12 12 PKGORN T2TR-MS P TAPE AND REEL BOX INFORMATION Device Package Pins Site Length (mm) Width (mm) LOG114AIRGVR RGV 16 MLA 346.0 346.0 29.0 LOG114AIRGVT RGV 16 MLA 190.0 212.7 31.75 Pack Materials-Page 2 Height (mm) PACKAGE MATERIALS INFORMATION www.ti.com 17-May-2007 Pack Materials-Page 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Telephony www.ti.com/telephony Low Power Wireless www.ti.com/lpw Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated