250 MHz QAM IF DOWNCONVERTER UPC2798GR FEATURES DESCRIPTION • RF/LO FREQUENCY RANGE: 30-250 MHz NEC's UPC2798GR is a Silicon MMIC Downconverter manufactured with the NESAT™III silicon bipolar process. This product consists of an input AGC amplifier, mixer, local oscillator, and video amplifier. It is housed in a small 20 pin SSOP package. The device is designed for use as an IF downconverter for digital CATV settops and cable modems utilizing QAM modulation. • ON CHIP VCO • LOW DISTORTION AGC AMPLIFIER: -9 dBm IIP3 @ MIN Gain • ON CHIP VIDEO AMP: 3.0 Vp-p (VCC = 5 V) • SMALL 20 PIN SSOP PACKAGE NEC's stringent quality assurance and test procedures ensure the highest reliability and performance. • AVAILABLE ON TAPE AND REEL ELECTRICAL CHARACTERISTICS (TA = 25°C, RF = 45 MHz, LO = 55 MHz, PLO = -10 dBm, unless otherwise specified) PART NUMBER PACKAGE OUTLINE SYMBOLS PARAMETERS AND CONDITIONS UPC2798GR S20 UNITS MIN TYP MAX Total Block (VCC1 = 5 V, VCC2 = 5 V, RL = 1 kΩ) Circuit Current (no input signal) mA 24.0 35.5 45.0 CGMAX1 Maximum Conversion Gain, VAGC = 4.0 V, pins G1A - G1B shorted dB 68.0 74.0 76.0 CGMAX2 Maximum Conversion Gain, VAGC = 4.0 V, pins G1A - G1B open dB CGMIN1 Minimum Conversion Gain, VAGC = 1.0 V, pins G1A - G1B shorted dB CGMIN2 Minimum Conversion Gain, VAGC = 1.0 V, pins G1A - G1B open dB 22.0 ICC 58.0 32.0 39.0 IIP3 Input Intercept Point, VAGC = 1.0 V, pins G1A - G1B shorted dBm -14.0 IIP3 Input Intercept Point, VAGC = 1.0 V, pins G1A - G1B open dBm -8.0 43.0 Total Block (VCC1 = 5 V, VCC2 = 9 V, RL = 1 kΩ) Circuit Current (no input signal) mA 32.0 47.0 60.0 CGMAX1 ICC Maximum Conversion Gain, VAGC = 4.0 V, pins G1A - G1B shorted dB 72.0 78.5 81.0 CGMAX2 Maximum Conversion Gain, VAGC = 4.0 V, pins G1A - G1B open dB CGMIN1 Minimum Conversion Gain, VAGC = 1.0 V, pins G1A - G1B shorted dB 43.5 CGMIN2 Minimum Conversion Gain, VAGC = 1.0 V, pins G1A - G1B open dB 22.5 dBm -7.5 IIP3 Input Intercept Point, VAGC = 1.0 V, pins G1A - G1B open AGC Amplifier and Mixer Block (VCC1 = 5 V) ICC Circuit Current (no input signal) 59.0 mA 15.0 fOSC fIF CGMAX RF Input Frequency Range OSC Frequency Range IF Output Frequency Range Maximum Conversion Gain, VAGC = 4.0 V MHz MHz MHz dB 30 30 DC CGMIN Minimum Conversion Gain, VAGC = 1.0 V dB GCR AGC Dynamic Range, VAGC = 1.0 to 4.0 V dB Noise Figure, SSB, VAGC = 4.0 V (MAX Gain) dB VAGC (H) AGC Voltage High, at MAX Gain V VAGC (L) AGC Voltage Low, at MIN Gain fRF NF AGC IIP3 AGC Input Intercept Point, at MIN Gain 23.0 250 250 150 25 -7 26 32 9 4.0 V dBm 28.0 1.0 -9 California Eastern Laboratories UPC2798GR ELECTRICAL CHARACTERISTICS (TA = 25°C, RF = 45 MHz, LO = 55 MHz, PLO = -10 dBm, unless otherwise specified) PART NUMBER PACKAGE OUTLINE SYMBOLS UPC2798GR S20 PARAMETERS AND CONDITIONS UNITS MIN TYP MAX Circuit Current (no input signal) mA 9.0 12.5 17.0 Output Voltage Vp-p 3.0 G1 Differential Gain 1, pins G1A and G1B shorted, VOUT = 3.0 Vp-p V/V 200 G2 Differential Gain 2, pins G1A and G1B open, VOUT = 3.0 Vp-p V/V 26 Video Amp Block (VCC2 = 5 V, differential, RL = 1 kΩ) ICC VOUT Video Amp Block (VCC2 = 9 V, differential, RL = 1 kΩ) ICC Circuit Current (no input signal) mA 17.0 24.0 Output Voltage Vp-p 3.0 G1 Differential Gain 1, Pins G1A and G1B shorted V/V 385 G2 Differential Gain 2, Pins G1A and G1B open V/V 28.5 VOUT 32.0 Video Amp Block (VCC2 = 5 V, single ended, RL = 50 Ω) AVS1 Single-ended Gain, pins G1A - G1B shorted dB 40.0 AVS2 Single-ended Gain, pins G1A - G1B open dB 22.5 IIP3 Input Intercept Point, pins G1A - G1B open, f1 = 9 MHz, f2 = 11 MHz dBm -11.5 Video Amp Block (VCC2 = 9 V, single ended, RL = 50 Ω) AVS1 Single-ended Gain, pins G1A - G1B shorted dB 45.0 AVS2 Single-ended Gain, pins G1A - G1B open dB 23.5 IIP3 Input Intercept Point, pins G1A - G1B open, f1 = 9 MHz, f2 = 11 MHz dBm -5.0 50 Video Amp Block (VCC2 = 5 or 9 V, common, RL = 1 k Ω) BWG1 Bandwidth 1, G1 MHz BWG2 Bandwidth 2, G2 MHz 50 RIN 1 Input Resistance 1, G1 kΩ 3.5 RIN 2 Input Resistance 2, G2 kΩ 9.7 1.6 Input Capacitance, CIN pF CMRR CIN Common Mode Rejection Ratio, VCM = 1.0 Vp-p, ƒ = 100 kHz dB 80 PSRR Power Supply Rejection Ratio dB 70 Rise Time ns 2.6 Propagation Delay Time ns 4.4 τR τD ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) SYMBOLS VCC1 VCC2 PD UNITS RATINGS Supply Voltage 1 (Mixer Block) PARAMETERS V 6.0 Supply Voltage 2 (Video Amp Block) V 6.0 Power Dissipation, TA = 85˚C2 RECOMMENDED OPERATING CONDITIONS SYMBOL mW 430 TOP Operating Temperature °C -40 to +85 TSTG Storage Temperature °C -55 to +150 SYMBOLS PARAMETERS UNITS RATINGS VCC1 Supply Voltage 1 (Mixer Block) V 6.0 VCC2 Supply Voltage 2 (Video Amp Block) V 11.0 PD Power Dissipation, TA = 75˚C2 mW 500 TOP Operating Temperature °C -40 to +75 TSTG Storage Temperature °C -55 to +150 Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. Mounted on a 50 x 50 x 1.6 mm epoxy glass PWB. PARAMETER VCC1 Supply Voltage 1 VCC2 UNITS MIN TYP MAX V 4.5 5.0 5.5 Supply Voltage 2 V 4.5 5.0 10.0 TA1 Operating Temp. Range 1* °C -40 +25 +85 TA2 2** °C -40 +25 +75 Operating Temp. Range Notes: * @ VCC1 = VCC2 = 4.5 to 5.5 V ** @ VCC1 = 4.5 to 5.5 V, VCC2 = 4.5 to 10.0 V UPC2798GR TYPICAL CHARACTERISTICS (by measurement circuit 1: AGC Amp and Mixer Block) CIRCUIT CURRENT vs. SUPPLY VOLTAGE CONVERSION GAIN vs. INPUT FREQUENCY 30 no input signal TA = 25˚C VAGC = 0 V 40 VAGC = 4.0 V Total Conversion Gain, CG (dB) Circuit Current, ICC (mA) 50 Mixer +AGC+VCO 30 Video Amp 20 10 0 0 4 2 6 8 10 20 10 VAGC = 2.6 V 0 -10 -20 -30 12 VAGC = 0.0 V PRF = 60 dBm fOSC = fRF+5 MHZ, POSC = -10 dBm VCC = 5 V, TA = 25˚C 0 50 100 200 150 250 300 Input Frequency, fRF (MHz) Supply Voltage, VCC (V) CONVERSION GAIN vs. IF FREQUENCY NOISE FIGURE vs. AGC VOLTAGE 30 30 Noise Figure, NF (dB) Conversion Gain, CG (dB) VAGC = 4.0 V 20 10 VAGC = 2.6 V 0 -10 VAGC = 0.0 V -20 20 10 VCC = 5 V fRF = 100 MHZ fOSC = 120 MHZ POSC = -10 dBm TA = 25˚C DSB fRF = 45 MHZ, PRF = -60 dBm fOSC = 50~200 MHZ, POSC = -10 dBm VCC = 5 V, TA = 25˚C -30 0 30 60 120 90 150 0 180 0 1 IF Frequency, fIF (MHz) 4 3 5 THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER CONVERSION GAIN vs. AGC VOLTAGE -10 30 VCC = 5 V fRF = 45 MHZ PRF = -60 dBm fOSC = 50 MHZ POSC = -10 dBm TA = 25˚C 20 VCC = 5 V VAGC = 0 V fRF1 = 44 MHZ fRF2 = 46 MHZ -30 fOSC = 55 MHZ POSC = -10 dBm TA = 25˚C -40 -20 Output Power, POUT (dBm) Conversion Gain, CG (dB) 2 AGC Voltage, VAGC (V) 10 0 POUT -50 IM3 -60 -70 -80 -10 0 1 2 3 4 AGC Voltage, VAGC (V) 5 -90 -60 -50 -40 -30 -20 Input Power, PIN (dBm) -10 0 UPC2798GR STANDARD CHARACTERISTICS (by measurement circuit 2: Video Amp, RL = 1 kΩ, TA = 25˚C) DIFFERENTIAL GAIN vs. INPUT FREQUENCY DIFFERENTIAL GAIN vs. INPUT FREQUENCY 40 400 Differential Gain (V/V) Differential Gain (V/V) VCC = 9 V 300 200 VCC = 5 V 100 30 VCC = 9 V VCC = 5 V 20 10 G1A-G1B : open POUT = 1.5 V p-p const. G1A-G1B : short POUT = 1.5 Vp-p const. 0 0 20 0 40 80 60 100 0 20 40 Input Frequency, fIN (MHz) OUTPUT POWER vs. INPUT POWER (VIDEO AMP) OUTPUT POWER vs. INPUT POWER (VIDEO AMP) 0 VCC = 9 V Output Power, Pout (dBm) Output Power, Pout (dBm) VCC = 9 V -10 VCC = 5 V -20 -10 -20 VCC = 5 V -30 -40 fin = 10 MHZ G1A-G1B : open fin = 10 MHZ G1A-G1B : short -30 -40 -30 -10 -20 0 Input Power, PIN (dBm) 500 fin = 10 MHZ 400 300 VCC = 9 V 200 100 short VCC = 5 V 30 43 56 100 246 Resistance (Ω) -50 -40 -30 -20 -10 Input Power, PIN (dBm) DIFFERENTIAL GAIN vs. RESISTANCE Differential Gain (V/V) 100 Input Frequency, fIN (MHz) 0 0 80 60 2000 open 0 10 UPC2798GR STANDARD CHARACTERISTICS (by measurement circuit 3: Video Amp, RL = 50 Ω, TA = 25˚C) GAIN vs. INPUT FREQUENCY GAIN vs. INPUT FREQUENCY 50 Single-ended Gain, AVS (dB) Single-ended Gain, AVS (dB) 50 40 30 20 10 40 30 20 10 VCC2 = 5 V G1A-G1B: short 0 0.1 VCC2 = 5 V G1A-G1B: open 1 10 0 0.1 100 Single-ended Gain, AVS (dB) Single-ended Gain, AVS (dB) 100 50 40 30 20 10 40 30 20 10 VCC2 = 9 V G1A-G1B: short 1 VCC2 = 9 V G1A-G1B: open 10 0 0.1 100 1 10 100 Input Frequency, fIN (MHz) Input Frequency, fIN (MHz) THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER 20 20 0 Output Power, POUT (dBm) Output Power, POUT (dBm) 10 GAIN vs. INPUT FREQUENCY GAIN vs. INPUT FREQUENCY 50 0 0.1 1 Input Frequency, fIN (MHz) Input Frequency, fIN (MHz) POUT -20 IM3 -40 VCC2 = 5 V f1 = 9 MHz f2 = 11 MHz G1A–G1B: open -60 -80 -50 -40 -30 -20 Input Power, PIN (dBm) -10 0 POUT -20 IM3 -40 VCC2 = 9 V f1 = 9 MHz f2 = 11 MHz G1A–G1B: open -60 -80 -50 -40 -30 -20 Input Power, PIN (dBm) -10 UPC2798GR TYPICAL CHARACTERISTICS (by measurement circuit 4: Total Block, fRF = 45 MHz, PRF = -60 dBm, Posc = -10 dBm) CONVERSION GAIN vs. IF FREQUENCY CONVERSION GAIN vs. IF FREQUENCY 80 60 VAGC = 4 V VAGC = 3 V 40 VAGC = 1 V 20 Conversion Gain, CG (dB) Conversion Gain, CG (dB) 80 VAGC = 4 V 60 VAGC = 3 V 40 VAGC = 1 V 20 VCC1 = 5 V, VCC2 = 5 V G1A - G1B : short 1 KΩ load, TA = 25˚C VCC1 = 5 V, VCC2 = 9 V G1A - G1B : short 1 KΩ load, TA = 25˚C 0 0 40 80 120 0 160 0 80 120 IF Frequency, fIF (MHz) IF Frequency, fIF (MHz) CONVERSION GAIN vs. IF FREQUENCY CONVERSION GAIN vs. IF FREQUENCY 80 160 80 Conversion Gain, CG (dB) Conversion Gain, CG (dB) 40 60 VAGC = 4 V 40 VAGC = 3 V 20 60 VAGC = 4 V 40 VAGC = 3 V 20 VCC1 = 5 V, VCC2 = 5 V G1A - G1B : open 1 KΩ load, TA = 25˚C VCC1 = 5 V, VCC2 = 9 V G1A - G1B : open 1 KΩ load, TA = 25˚C 0 0 0 40 80 120 IF Frequency, fIF (MHz) 160 0 40 80 120 IF Frequency, fIF (MHz) 160 UPC2798GR TYPICAL CHARACTERISTICS (by measurement circuit 4: Total Block, PRF = -60 dBm, fOSC = fRF + 10 MHz, POSC = -10 dBm) CONVERSION GAIN vs. INPUT FREQUENCY CONVERSION GAIN vs. INPUT FREQUENCY 80 80 VAGC = 4 V Conversion Gain, CG (dB) Conversion Gain, CG (dB) VAGC = 4 V 60 VAGC = 3 V 40 VAGC = 1 V 20 VCC1 = 5 V VCC2 = 5 V 1 KΩ load G1A-G1B : short TA = 25˚C 0 0 50 VAGC = 1 V 40 20 VCC1 = 5 V VCC2 = 9 V 1 KΩ load G1A-G1B : short TA = 25˚C 0 100 150 200 250 0 50 100 150 200 Input Frequency, fRF (MHz) Input Frequency, fRF (MHz) CONVERSION GAIN vs. INPUT FREQUENCY CONVERSION GAIN vs. INPUT FREQUENCY 250 80 Conversion Gain, CG (dB) 80 Conversion Gain, CG (dB) VAGC = 3 V 60 VAGC = 4 V 60 40 VAGC = 3 V VAGC = 1 V 20 VCC1 = 5 V, VCC2 = 5 V G1A-G1B : open 1 KΩ load, TA = 25˚C 0 0 50 100 VAGC = 4 V 60 VAGC = 3 V 40 VAGC = 1 V 20 VCC1 = 5 V, VCC2 = 9 V G1A-G1B : open 1 KΩ load, TA = 25˚C 0 150 200 Input Frequency, fRF (MHz) 250 0 50 100 150 200 Input Frequency, fRF (MHz) 250 UPC2798GR STANDARD CHARACTERISTICS (by measurement circuit 4: Total Block) THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER 0 POUT Output Power, POUT (dBm) Output Power, POUT (dBm) 0 -20 IM3 -40 VCC1 = 5 V VCC2 = 5 V f1 = 44 MHz f2 = 46 MHz fOSC = 55 MHz POSC = -10 dBm G1A–G1B: short -60 -80 -50 -40 -30 -20 -10 0 THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER Output Power, POUT (dBm) 0 POUT -20 IM3 -40 -80 -50 VCC1 = 5 V VCC2 = 5 V f1 = 44 MHz f2 = 46 MHz fOSC = 55 MHz POSC = -10 dBm G1A–G1B: short -40 -30 -20 -10 Input Power, PIN (dBm) IM3 -40 VCC1 = 5 V VCC2 = 9 V f1 = 44 MHz f2 = 46 MHz fOSC = 55 MHz POSC = -10 dBm G1A–G1B: open -60 -80 -50 -40 -30 -20 -10 Input Power, PIN (dBm) Input Power, PIN (dBm) -60 POUT -20 0 0 UPC2798GR STANDARD CHARACTERISTICS (by application circuit example : MIXER block) NOISE FIGURE vs. AGC VOLTAGE CONVERSION GAIN vs. INPUT FREQUENCY 30 VCC = 5.5 V Noise Figure, NF (dB) Conversion Gain, CG (dB) 30 VCC = 5.0 V 25 VCC = 4.5 V 10 fRF = 50 MHZ fIF = 10 MHZ VCC = 4.5 V VCC = 5.0 V VCC = 5.5 V DSB fRF = 50 MHz fIF = 10 MHz PRF = -50 dBm VAGC = 4 V 20 0 30 40 50 0 60 1 2 3 5 AGC Voltage, VAGC (V) CONVERSION GAIN vs. AGC VOLTAGE THIRD ORDER INTERMODULATION LEVEL AND OUTPUT POWER vs. INPUT POWER -10 fRF = 50 MHZ fIF = 10 MHZ PRF = -50 dBm VCC = 4.5 V VCC = 5.0 V 20 VCC = 5.5 V Output Power, POUT (dBm) -20 10 0 -30 POUT -40 -50 IM3 -60 -70 VCC = 5 V fRF1 = 45 MHZ fRF2 = 46 MHZ fOSC= 55 MHZ VAGC= 0 V -80 -90 -10 0 1 2 4 3 5 AGC Voltage, VAGC (V) 70 60 50 40 VCC = 5 V 30 0 5 10 -100 -60 -50 -40 -30 -20 -10 Input Power, PIN (dBm) OSCILLATOR FREQUENCY vs. TUNING VOLTAGE Oscillator Frequency, fOSC (MHz) 4 Input Frequency, fRF (MHz) 30 Conversion Gain, CG (dB) 20 15 Tuning Voltage, VTU (V) 20 0 10 UPC2798GR PIN FUNCTIONS Pin No. Pin Name Pin Voltage Typ. (V) 1 AGC IN1 1.5 2 AGC IN2 Function and Explanation RF input pins. Pins 1 and 2 are each base inputs to a differential amplifier. In the case of a single-ended input, bypass the unused pin to ground through a capacitor. Equivalent Circuit 4 AGC Control 1.5 Reg 1 3 VAGC 0~5 Gain control pin of the mixer input amplifier. VAGC up = gain up. It is recommended to use a 100k Ω voltage divider at this pin. 4 VCC1 5.0 Supply voltage pin for the downconverter block. This pin should be connected with a bypass capacitor (e.g., 1000 pF) to minimize ground impedance. 5 OSC OUT 4.0 Output pin for the internal oscillator. This pin may be connected to the input of a PLL synthesizer. 2 4 AGC Control 3 4 5 REG 6 GND 0.0 Ground pin. This pin must be connected to system ground. Form ground pattern as wide as possible to minimize ground impedance. 7 OSC B2 2.4 Input pins for the internal oscillator. The internal oscillator consists of a balanced amplifier. 7 8 OSC C1 4.6 9 OSC C2 4.6 8 4 9 10 Reg Reg 10 OSC B1 2.4 UPC2798GR PIN FUNCTIONS Pin No. Pin Name Pin Voltage Typ. (V) ( ) is value at VCC = 9V 11 OUT2 2.5 (4.7) Function and Explanation Output pins for the video amplifier. With RL = 1k Ω, the differential output voltage is 3 Vp-p. OUT1 and INA are in phase. OUT2 and INB are in phase. In the case of a single-ended output, bypass the unused pin to ground through a capacitor. OUT1 2.5 (4.7) 13 VCC2 5~9 Supply voltage pin for the video amplifier block. This pin should be connected with a bypass capacitor (e.g., 1000 pF) to minimize ground impedance. 14 INB 2.5 (4.1) Input pins for the video amplifier. These pins have high impedance. In the case of a single-ended input, bypass the unused pin to ground through a capacitor. INA 2.5 (4.1) 16 G1B 1.7 (3.3) 13 12 11 12 15 Equivalent Circuit 17 15 13 14 Gain control pins for the video amplifier. The gain may be adjusted by varying the value of the resistor between pins 16 and 17. Maximum gain = short; Minimum gain = open. REG 17 G1A 1.7 (3.3) 18 MIX OUT1 3.7 19 MIX OUT2 3.7 Output pins for the downconverter. These are emitter follower outputs which feature low impedance. In the case of a single-ended output, bypass the unused pin to ground through a capacitor. 4 18 19 REG 20 GND 0.0 Ground pin. This pin must be connected to system ground. Form ground pattern as wide as possible to minimize ground impedance. 16 UPC2798GR MEASUREMENT CIRCUIT 1 AGC & MIXER BLOCK 10nF 10nF AGC IN 100k VAGC 220nF VCC 1 1nF OSC OUT 100k 220nF 10nF 10nF 10nF OSC IN 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 MIX OUT 10nF 10nF 50Ω MEASUREMENT CIRCUIT 2 VIDEO AMP BLOCK RL = 1kΩ 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 10nF Signal 50Ω Generator 50Ω 10nF 220nF Vcc 2 1nF 950Ω 50Ω Spectrum Analyzer 10nF 11 10nF 1kΩ UPC2798GR MEASUREMENT CIRCUIT 3 VIDEO AMP BLOCK RL = 50Ω 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 Signal 50Ω Generator 50Ω 10nF 10nF 220nF Vcc 2 1nF 950Ω 50Ω 10nF Spectrum Analyzer 10nF 50Ω MEASUREMENT CIRCUIT 4 TOTAL BLOCK 10nF 10nF AGC IN VAGC 220nF VCC 1 1nF OSC OUT 100k 100k 220nF 10nF 10nF 10nF OSC IN 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 1k 1k 5pF 10nF 10nF 220nF 1nF 10nF 10nF Vcc2 950Ω 50Ω Spectrum Analyzer 1kΩ UPC2798GR APPLICATION CIRCUIT EXAMPLE 10nF 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 10nF AGC IN 100k VAGC 220nF VCC 1 1nF OSC OUT 100k 220nF 10nF 10k 1000pF Vtu 10pF 20pF Cv 1.2 µ H 10pF 10k 1000pF 1k 1k 5pF 10nF 10nF 220nF 1nF 10nF Vcc2 OUT 1 OUT 2 10nF CV: ISV209 OUTLINE DIMENSIONS (Units in mm) INTERNAL BLOCK DIAGRAM PACKAGE OUTLINE SSOP 20 20 11 NEC C2798G XXXXX N 1 7.00 MAX xxxxx = Lot/Date Code 6.4±0.2 4.4±0.1 1.0±0.1 +0.10 0.15- 0.05 +0.10 0.22 - 0.05 1 20 AGC IN2 2 19 MIX OUT 2 VAGC 3 18 MIX OUT 1 VCC1 4 17 G1A OSC OUT 5 16 G1B GND 6 15 VAMP IN1 OSC B2 7 14 VAMP IN2 OSC C2 8 13 VCC2 OSC C2 9 12 OUT1 OSC B1 10 11 OUT2 10 1.5 ±0.1 1.8 MAX AGC IN1 GND 0.5±0.2 0.65 0.575 MAX All dimensions are typical unless specified otherwise. ORDERING INFORMATION PART NUMBER QUANTITY UPC2798GR-E1-A 2500/Reel Notes: Embossed tape, 12 mm wide. Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. EXCLUSIVE NORTH AMERICAN AGENT FOR RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279 24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) • Internet: http://WWW.CEL.COM 6/99 DATA SUBJECT TO CHANGE WITHOUT NOTICE 4-248 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Concentration Limit per RoHS (values are not yet fixed) Concentration contained in CEL devices -A Not Detected Lead (Pb) < 1000 PPM Mercury < 1000 PPM Not Detected Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability. 4-249