APT80F60J 600V, 84A, 0.055Ω Max, trr ≤ 370ns N-Channel FREDFET S S Power MOS 8™ is a high speed, high voltage N-channel switch-mode power MOSFET. This 'FREDFET' version has a drain-source (body) diode that has been optimized for high reliability in ZVS phase shifted bridge and other circuits through reduced trr, soft recovery, and high recovery dv/dt capability. Low gate charge, high gain, and a greatly reduced ratio of Crss/Ciss result in excellent noise immunity and low switching loss. The intrinsic gate resistance and capacitance of the poly-silicon gate structure help control di/dt during switching, resulting in low EMI and reliable paralleling, even when switching at very high frequency. D G SO 2 T- 27 "UL Recognized" file # E145592 IS OTO P ® D APT80F60J Single die FREDFET G S TYPICAL APPLICATIONS FEATURES • Fast switching with low EMI • ZVS phase shifted and other full bridge • Low trr for high reliability • Half bridge • Ultra low Crss for improved noise immunity • PFC and other boost converter • Low gate charge • Buck converter • Avalanche energy rated • Single and two switch forward • RoHS compliant • Flyback Absolute Maximum Ratings Symbol ID Ratings Parameter Continuous Drain Current @ TC = 25°C 84 Continuous Drain Current @ TC = 100°C 52 Unit A IDM Pulsed Drain Current VGS Gate-Source Voltage ±30 V EAS Single Pulse Avalanche Energy 2 3352 mJ IAR Avalanche Current, Repetitive or Non-Repetitive 60 A 1 447 Thermal and Mechanical Characteristics Typ Max Unit W PD Total Power Dissipation @ TC = 25°C 961 RθJC Junction to Case Thermal Resistance 0.13 RθCS Case to Sink Thermal Resistance, Flat, Greased Surface TJ,TSTG Operating and Storage Junction Temperature Range VIsolation RMS Voltage (50-60hHz Sinusoidal Waveform from Terminals to Mounting Base for 1 Min.) WT Torque Package Weight Terminals and Mounting Screws. Microsemi Website - http://www.microsemi.com 0.15 -55 150 °C/W °C V 2500 1.03 oz 29.2 g 10 in·lbf 1.1 N·m Rev C 4-2011 Min Characteristic 050-8175 Symbol Static Characteristics TJ = 25°C unless otherwise specified Symbol Parameter Test Conditions Min VBR(DSS) Drain-Source Breakdown Voltage VGS = 0V, ID = 250μA 600 ∆VBR(DSS)/∆TJ Breakdown Voltage Temperature Coefficient RDS(on) Drain-Source On Resistance VGS(th) Gate-Source Threshold Voltage ∆VGS(th)/∆TJ VGS = 10V, ID = 60A Zero Gate Voltage Drain Current IGSS Gate-Source Leakage Current Dynamic Characteristics 2.5 VGS = VDS, ID = 2.5mA Threshold Voltage Temperature Coefficient IDSS Symbol Reference to 25°C, ID = 250μA 3 VDS = 600V TJ = 25°C VGS = 0V TJ = 125°C APT80F60J Typ Max 0.60 0.042 4 -10 0.055 5 250 1000 ±100 VGS = ±30V Test Conditions gfs Forward Transconductance VDS = 50V, ID = 60A 117 Ciss Input Capacitance 23994 Crss Reverse Transfer Capacitance VGS = 0V, VDS = 25V f = 1MHz Coss Output Capacitance 4 Effective Output Capacitance, Charge Related Co(er) 5 Effective Output Capacitance, Energy Related Qgs Gate-Source Charge Qgd Gate-Drain Charge td(on) tr td(off) tf Min Typ nA Unit S 245 VGS = 0V, VDS = 0V to 400V pF 1170 606 VGS = 0 to 10V, ID = 60A, 598 VDS = 300V 128 nC 251 Turn-On Delay Time Resistive Switching 134 Current Rise Time VDD = 400V, ID = 60A 156 Turn-Off Delay Time Max 2201 Co(cr) Total Gate Charge μA TJ = 25°C unless otherwise specified Parameter Qg Unit V V/°C Ω V mV/°C RG = 2.2Ω 6 , VGG = 15V ns 408 123 Current Fall Time Source-Drain Diode Characteristics Symbol IS ISM VSD Parameter Continuous Source Current (Body Diode) Pulsed Source Current (Body Diode) 1 Diode Forward Voltage trr Reverse Recovery Time Qrr Reverse Recovery Charge Irrm Reverse Recovery Current dv/dt Peak Recovery dv/dt Test Conditions Min Typ D MOSFET symbol showing the integral reverse p-n junction diode (body diode) A G 447 S 1.0 370 690 TJ = 25°C TJ = 125°C TJ = 25°C VDD = 100V TJ = 125°C diSD/dt = 100A/μs TJ = 25°C Unit 84 ISD = 60A, TJ = 25°C, VGS = 0V ISD = 60A 3 Max TJ = 125°C ISD ≤ 60A, di/dt ≤1000A/μs, VDD = 400V, TJ = 125°C 2.6 7.0 14.5 20 V ns μC A 25 V/ns 1 Repetitive Rating: Pulse width and case temperature limited by maximum junction temperature. 050-8175 Rev C 4-2011 2 Starting at TJ = 25°C, L = 2.08mH, RG = 25Ω, IAS = 60A. 3 Pulse test: Pulse Width < 380μs, duty cycle < 2%. 4 Co(cr) is defined as a fixed capacitance with the same stored charge as COSS with VDS = 67% of V(BR)DSS. 5 Co(er) is defined as a fixed capacitance with the same stored energy as COSS with VDS = 67% of V(BR)DSS. To calculate Co(er) for any value of VDS less than V(BR)DSS, use this equation: Co(er) = -3.14E-7/VDS^2 + 7.31E-8/VDS + 2.09E-10. 6 RG is external gate resistance, not including internal gate resistance or gate driver impedance. (MIC4452) Microsemi reserves the right to change, without notice, the specifications and information contained herein. APT80F60J 350 V GS 160 = 10V T = 125°C TJ = -55°C ID, DRIAN CURRENT (A) 250 200 TJ = 25°C 150 100 TJ = 150°C 50 120 6V 100 80 60 40 5V 20 TJ = 125°C 0 0 5 10 15 20 25 VDS(ON), DRAIN-TO-SOURCE VOLTAGE (V) 4.5V 0 Figure 1, Output Characteristics 2.5 5 10 15 20 25 30 VDS, DRAIN-TO-SOURCE VOLTAGE (V) Figure 2, Output Characteristics 280 NORMALIZED TO VGS = 10V @ 42A VDS> ID(ON) x RDS(ON) MAX. 250μSEC. PULSE TEST @ <0.5 % DUTY CYCLE 240 2.0 ID, DRAIN CURRENT (A) 1.5 1.0 0.5 200 TJ = -55°C 160 TJ = 25°C 120 TJ = 125°C 80 40 0 -55 -25 0 25 50 75 100 125 150 TJ, JUNCTION TEMPERATURE (°C) Figure 3, RDS(ON) vs Junction Temperature 0 120 0 1 2 3 4 5 6 7 8 VGS, GATE-TO-SOURCE VOLTAGE (V) Figure 4, Transfer Characteristics 20,000 Ciss 10,000 80 TJ = 125°C 60 40 1000 Coss 100 Crss 20 0 0 16 VGS, GATE-TO-SOURCE VOLTAGE (V) C, CAPACITANCE (pF) TJ = -55°C TJ = 25°C 10 20 30 40 50 60 70 80 ID, DRAIN CURRENT (A) Figure 5, Gain vs Drain Current 100 200 300 400 500 VDS, DRAIN-TO-SOURCE VOLTAGE (V) Figure 6, Capacitance vs Drain-to-Source Voltage 12 VDS = 100V 10 VDS = 250V 8 6 VDS = 400V 4 2 0 0 280 ID = 42A 14 0 10 90 100 200 300 400 500 Qg, TOTAL GATE CHARGE (nC) Figure 7, Gate Charge vs Gate-to-Source Voltage ISD, REVERSE DRAIN CURRENT (A) gfs, TRANSCONDUCTANCE 100 240 200 160 TJ = 25°C 120 TJ = 150°C 80 40 0 0 0.3 0.6 0.9 1.2 1.5 VSD, SOURCE-TO-DRAIN VOLTAGE (V) Figure 8, Reverse Drain Current vs Source-to-Drain Voltage Rev C 4-2011 RDS(ON), DRAIN-TO-SOURCE ON RESISTANCE = 7,8 & 10V GS 050-8175 ID, DRAIN CURRENT (A) 300 0 V J 140 APT80F60J 447 447 100 IDM 10 ID, DRAIN CURRENT (A) ID, DRAIN CURRENT (A) 100 13μs 100μs Rds(on) 1ms 10ms 1 0.1 100ms DC line TJ = 125°C TC = 75°C 1 13μs 10 100μs 1ms Rds(on) 10ms TJ = 150°C TC = 25°C 1 0.1 10 100 800 VDS, DRAIN-TO-SOURCE VOLTAGE (V) Figure 9, Forward Safe Operating Area IDM 100ms DC line Scaling for Different Case & Junction Temperatures: ID = ID(T = 25°C)*(TJ - TC)/125 C 1 10 100 800 VDS, DRAIN-TO-SOURCE VOLTAGE (V) Figure 10, Maximum Forward Safe Operating Area D = 0.9 0.20 0.7 0.15 0.5 Note: 0.10 P DM ZθJC, THERMAL IMPEDANCE (°C/W) 0.25 0.3 t2 0.05 t1 = Pulse Duration t 0.1 0 t1 0.05 10-5 Duty Factor D = 1 /t2 Peak T J = P DM x Z θJC + T C SINGLE PULSE 10-4 10-3 10-2 10-1 RECTANGULAR PULSE DURATION (seconds) Figure 11. Maximum Effective Transient Thermal Impedance Junction-to-Case vs Pulse Duration SOT-227 (ISOTOP®) Package Outline e3 100% Sn Plated 11.8 (.463) 12.2 (.480) 31.5 (1.240) 31.7 (1.248) 7.8 (.307) 8.2 (.322) r = 4.0 (.157) (2 places) 4.0 (.157) 4.2 (.165) (2 places) 3.3 (.129) 3.6 (.143) Rev C 4-2011 14.9 (.587) 15.1 (.594) 050-8175 8.9 (.350) 9.6 (.378) Hex Nut M 4 (4 places ) W=4.1 (.161) W=4.3 (.169) H=4.8 (.187) H=4.9 (.193) (4 places) 0.75 (.030) 0.85 (.033) 12.6 (.496) 12.8 (.504) 25.2 (0.992) 25.4 (1.000) 1.95 (.077) 2.14 (.084) * Source 30.1 (1.185) 30.3 (1.193) Drai n * Emitter terminals are shorte d internally. Current handlin g capability is equal for either Source terminal . 38.0 (1.496) 38.2 (1.504) * Source Dimensions in Millimeters and (Inches) Gate 1.0