CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO GENERAL DESCRIPTION FEATURES The CM6802 is a green PFC/PWM. It is the new generation ! of ML4802, ML4841, ML4801 and ML4824-2. Its system Patent Number #5,565,761, #5,747,977, #5,742,151, #5,804,950, #5,798,635 clock frequency is generated by the external RT and CT, ! fosc=2 x fpwm =4 x fpfc and then its PWM frequency is 50% of the clock and its ! No bleed resistor required PFC frequency is 25% of the clock. CM6802 is designed to ! Before the chip wakes up, IAC can start up VCC be pin-pin compatible with CM6800 family, ML4800 family ! Pin to pin Compatible with CM6800, ML4824 and ML4800 and ML4824 family. Its PWM (DC to DC section) can be easily configured to Voltage Mode or Current Mode. (It needs to modify the values of the external component to The green mode function can easily be designed so during the work properly). ! User Program PFC automatic green mode threshold no load condition, its input power can be less than 0.75Watt (patented) without shutting off PFC. Its PFC green mode threshold and ! User Program PWM automatic green mode threshold the PWM green mode threshold can separately set by (patented) selecting the proper the RC filter at ISENSE pin (pin3) and ! CT on RAMP 1 pin (pin 7). Power Factor Correction (PFC) Input power less than 0.75Watt without shutting off PFC at no load condition. allows the use of smaller, lower cost bulk capacitors, ! Additional folded-back current limit for PWM section. reduces power line loading and stress on the switching ! 23V Bi-CMOS process FETs, and results in a power supply that fully compiles with ! PWM pulse keeping for the green mode IEC-1000-3-2 specifications. Intended as a BiCMOS ! VIN OK guaranteed turn on PWM at 2.5V instead of 1.5V version of the industry-standard CM6800, CM6802 includes ! Internally synchronized leading edge PFC and trailing edge circuits for the implementation of leading edge, average current, “boost” type power factor correction and a trailing PWM in one IC ! edge, pulse width modulator (PWM). Both PFC and PWM Slew rate enhanced transconductance error amplifier for ultra-fast PFC response Gate-driver with 0.5A capabilities minimizes the need for ! Low start-up current (30µA typ.) external driver circuits. Low power requirements improve ! Low operating current (3.0mA type.) efficiency and reduce component costs. ! Low total harmonic distortion, high PF ! Reduces ripple current in the storage capacitor between the An over-voltage comparator shuts down the PFC section in the event of a sudden decrease in load. The PFC section PFC and PWM sections ! also includes peak current limiting and input voltage Average current, continuous or discontinuous boost leading edge PFC brownout protection. The PWM section can be operated in ! VCC OVP Comparator will turn off both PFC and PWM current or voltage mode, at up to 250kHz, and includes an ! Low Power Detect Comparator accurate 50% duty cycle limit to prevent transformer ! Tri-Fault detect to meet UL1950 saturation. ! PWM configurable for current mode or voltage mode When RAMP1 is 280KHz, fpfc is 70KHz and fpwm is ! Current fed gain modulator for improved noise immunity 140KHz. ! Brown-out control, over-voltage protection, UVLO, and soft operation start, and Reference OK 24 Hours Technical Support---WebSIM Champion provides customers an online circuit simulation tool called WebSIM. You could simply logon our website at www.champion-micro.com for details. 2003/06/25 Preliminary Champion Microelectronic Corporation Page 1 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO APPLICATIONS PIN CONFIGURATION SOP-16 (S16) / PDIP-16 (P16) Top View ! Desktop PC Power Supply ! Internet Server Power Supply ! IPC Power Supply 1 IEA O ! UPS 2 IAC ! Battery Charger 3 ! DC Motor Power Supply ISENSE 4 ! Monitor Power Supply V RMS ! Telecom System Power Supply 5 ! Distributed Power V EA O 16 V FB 15 V REF 14 V CC 13 SS P FC O U T 12 6 V DC PWM OUT 11 7 R AM P 1 GND 10 8 R AM P 2 D C I LIMIT 9 PIN DESCRIPTION Pin No. Symbol Description Min. Operating Voltage Typ. Max. Unit 1 IEAO PFC transconductance current error amplifier output 0 4.25 V 2 IAC PFC gain control reference input. Before the chip wakes up, 0 1 mA IAC is connected to VCC. After the chip wakes up, IAC is connected to AGC. 3 ISENSE Current sense input to the PFC current limit comparator -5 0.7 V 4 VRMS Input for PFC RMS line voltage compensation 0 6 V 5 SS Connection point for the PWM soft start capacitor 0 8 V 6 VDC PWM voltage feedback input 0 8 V 7 RAMP 1 Oscillator timing node; timing set by RT CT 1.2 3.9 V 0 6 V 0 1 V (RTCT) When in current mode, this pin functions as the current sense input; when in voltage mode, it is the PWM input from PFC (PWM RAMP) output (feed forward ramp). 8 RAMP 2 9 DC ILIMIT PWM current limit comparator input 10 GND Ground 2003/06/25 Preliminary Champion Microelectronic Corporation Page 2 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO 11 PWM OUT PWM driver output 0 VCC V 12 PFC OUT PFC driver output 0 VCC V 13 VCC Positive supply 10 20 V 14 VREF Buffered output for the internal 7.5V reference 15 VFB PFC transconductance voltage error amplifier input 16 VEAO 15 7.5 0 PFC transconductance voltage error amplifier output V 2.5 0 3 V 6 V BLOCK DIAGRAM 1 16 VEAO + 19.4V - LOW POWER DETECT GMv VREF 7.5V 14 REFERENCE . 2.75V 3.5K . 2.5V GMi POWER FACTOR CORRECTOR - PFC CMP + + . IAC Q R Q S Q R Q MPPFC VCC - -1V GAIN VRMS S + - + PFC OUT - MODULATOR 4 3 PFC OVP + - VCC 2 VCC OVP VCC + VFB VCC - 0.5V 15 13 IEAO 12 PFC ILIMIT 3.5K ISENSE MNPFC GND 7 RAMP1 OSCILLATOR CLK 350 RAMP2 SW SPST PWM CMP - 1.5V VDC SS CMP S Q R Q 11 - VFB - + . 2.45V SW SPST SW SPST + 1.0V MNPWM + SS SW SPST VIN OK GND DC ILIMIT PULSE WIDTH MODULATOR VREF Q 9 VCC PWM OUT Vcc 20uA 350 5 MPPWM + 6 PWMOUT LIMIT - 8 PFCOUT PWM DUTY DUTY CYCLE S DC ILIMIT VCC R 2003/06/25 Preliminary Champion Microelectronic Corporation UVLO GND fosc=2xfpwm=4xfpfc 10 Page 3 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO ORDERING INFORMATION Part Number CM6802IP Temperature Range -40℃ to 125℃ Package 16-Pin PDIP (P16) CM6802IS -40℃ to 125℃ 16-Pin SOP (S16) ABSOLUTE MAXIMUM RATINGS Absolute Maximum ratings are those values beyond which the device could be permanently damaged. Parameter Min. VCC IEAO ISENSE Voltage PFC OUT PWMOUT Voltage on Any Other Pin IREF IAC Input Current Peak PFC OUT Current, Source or Sink Peak PWM OUT Current, Source or Sink PFC OUT, PWM OUT Energy Per Cycle Junction Temperature Storage Temperature Range Operating Temperature Range Lead Temperature (Soldering, 10 sec) Thermal Resistance (θJA) Plastic DIP Plastic SOIC 0 -5 GND – 0.3 GND – 0.3 GND – 0.3 -65 -40 Max. Units 20 4.5 0.7 VCC + 0.3 VCC + 0.3 VREF + 0.3 10 1 1 1 1.5 150 150 125 260 V V V V V V mA mA A A µJ ℃ ℃ ℃ ℃ 80 105 ℃/W ℃/W ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply Vcc=+15V, RT = 5.0kΩ, CT = 1.0nF, TA=Operating Temperature Range (Note 1) Symbol Parameter Test Conditions CM6802 Min. Unit Typ. Max. 6 V 30 65 90 µmho 2.45 2.5 2.55 V -1.0 -0.5 µA 5.8 6.0 V Voltage Error Amplifier (gmv) Input Voltage Range Transconductance 0 VNONINV = VINV, VEAO = 3.75V Feedback Reference Voltage Input Bias Current Note 2 Output High Voltage Output Low Voltage Sink Current Source Current VFB = 3V, VEAO = 6V VFB = 1.5V, VEAO = 1.5V Open Loop Gain Power Supply Rejection Ratio 11V < VCC < 16.5V 0.1 0.4 -35 -20 V µA 30 40 µA 50 60 dB 50 60 dB Current Error Amplifier (gmi) Input Voltage Range Transconductance -1.5 VNONINV = VINV, VEAO = 3.75V Input Offset Voltage 2003/06/25 Preliminary 50 -12 Champion Microelectronic Corporation 100 0.7 V 150 µmho 12 mV Page 4 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO ELECTRICAL CHARACTERISTICS (Conti.) Unless otherwise stated, these specifications apply Vcc=+15V, RT = 5.0kΩ, CT = 1.0nF, TA=Operating Temperature Range (Note 1) Symbol Parameter Test Conditions CM6802 Typ. Input Bias Current -1.0 -0.5 µA Output High Voltage 4.0 4.25 V Output Low Voltage Sink Current ISENSE = +0.5V, IEAO = 4.0V Source Current ISENSE = -0.5V, IEAO = 1.5V Max. Unit Min. 0.65 1.0 V -65 -35 µA 35 75 µA 60 70 dB 60 75 dB Threshold Voltage 2.70 2.77 Hysteresis 230 Open Loop Gain Power Supply Rejection Ratio 11V < VCC < 16.5V PFC OVP Comparator 2.85 V 290 mV 0.6 V Low Power Detect Comparator Threshold Voltage 0.4 Hystersis 0.5 0.25 V VCC OVP Comparator Threshold Voltage Hysteresis 19 19.4 20 V 1.40 1.5 1.65 V -1.10 -1.00 -0.90 V 80 200 mV 250 ns PFC ILIMIT Comparator Threshold Voltage (PFC ILIMIT VTH – Gain Modulator Output) Delay to Output (Note 4) Overdrive Voltage = -100mV DC ILIMIT Comparator Threshold Voltage Delay to Output (Note 4) 0.95 Overdrive Voltage = 100mV 1.0 1.05 250 V ns VIN OK Comparator Threshold Voltage 2.35 2.45 2.55 V Hysteresis 0.8 1.0 1.2 V GAIN Modulator Gain (Note 3) Bandwidth Output Voltage = 3.5K*(ISENSE-IOFFSET) IAC = 100µA, VRMS = VFB = 1V 0.59 0.81 IAC = 100µA, VRMS = 1.1V, VFB = 1V 1.47 2.03 IAC = 150µA, VRMS = 1.8V, VFB = 1V 0.66 0.92 IAC = 300µA, VRMS = 3.3V, VFB = 1V 0.21 IAC = 100µA IAC = 250µA, VRMS = 1.1V, VFB = 1V PFC Initial Accuracy Oscillator TA = 25℃ Voltage Stability 11V < VCC < 16.5V Temperature Stability 2003/06/25 Preliminary Champion Microelectronic Corporation 0.29 10 0.70 0.80 66 MHz 0.90 V 75.5 kHz 1 % 2 % Page 5 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO ELECTRICAL CHARACTERISTICS (Conti.) Unless otherwise stated, these specifications apply Vcc=+15V, RT = 5.0kΩ, CT = 1.0nF, TA=Operating Temperature Range (Note 1) Symbol Parameter Test Conditions Total Variation Line, Temp CM6802 Min. 68 Ramp Valley to Peak Voltage Max. 84 2.5 PFC Dead Time (Note 4) CT Discharge Current Typ. VRAMP2 = 0V, VRAMP1 = 2.5V Unit kHz V 500 700 ns 6.5 10.5 mA 7.5 7.6 V 10 25 mV Reference Output Voltage TA = 25℃, I(VREF) = 1mA Line Regulation 11V < VCC < 16.5V 0mA < I(VREF) < 7mA; TA = 0℃~70℃ 10 20 mV 0mA < I(VREF) < 5mA; TA = -40℃~85℃ 10 20 mV Load Regulation 7.4 Temperature Stability 0.4 Total Variation Line, Load, Temp TJ = 125℃, 1000HRs Long Term Stability % 7.35 7.65 V 5 25 mV 0 % PFC Minimum Duty Cycle VIEAO > 4.0V Maximum Duty Cycle VIEAO < 1.2V 90 Output Low Rdson Output Low Voltage % 15 22.5 ohm IOUT = -100mA at room temp 0.8 1.5 V IOUT = -10mA, VCC = 8V at room temp 0.4 0.8 V 30 45 ohm Output High Rdson Output High Voltage 95 IOUT = 100mA, VCC = 15V at room temp Rise/Fall Time (Note 4) 13.5 CL = 1000pF 14.2 V 50 ns PWM Duty Cycle Range 0-49.5 Output Low Rdson Output Low Voltage % 15 22.5 ohm IOUT = -100mA at room temp 0.8 1.5 V IOUT = -10mA, VCC = 8V at room temp 0.7 1.5 V 30 45 ohm Output High Rdson Output High Voltage 0-50 IOUT = 100mA, VCC = 15V at room temp Rise/Fall Time (Note 4) 13.5 CL = 1000pF 14.2 V 50 ns Supply Start-Up Current VCC = 12V, CL = 0 Operating Current 30 50 µA 3.0 mA Undervoltage Lockout Threshold 14V, CL = 0 CM6802 14.7 15 15.3 V Undervoltage Lockout Hysteresis CM6802 4.85 5.0 5.15 V Note 1: Limits are guaranteed by 100% testing, sampling, or correlation with worst-case test conditions. Note 2: Includes all bias currents to other circuits connected to the VFB pin. -1 Note 3: Gain = K x 5.375V; K = (ISENSE – IOFFSET) x [IAC (VEAO – 0.625)] ; VEAOMAX = 6V Note 4: Guaranteed by design, not 100% production test. 2003/06/25 Preliminary Champion Microelectronic Corporation Page 6 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO 127 220 120 200 113 180 Transconductance (umho) Transconductance (umho) TYPICAL PERFORMANCE CHARACTERISTIC 106 99 92 85 78 71 160 140 120 100 80 60 40 64 20 57 0 -500 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 -400 -300 -200 3 -100 0 100 200 300 400 500 ISENSE (mV) VFB (V) Voltage Error Amplifier (gmv) Transconductance Current Error Amplifier (gmi) Transconductance 0.4 2 0.35 1.8 0.3 1.6 0.25 1.4 0.2 1.2 Gain Variable Gain Block Constant (K) 2.2 0.15 1 0.1 0.8 0.05 0.6 0.4 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 VRMS (V) 0.2 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 VRMS (V) Gain Modulator Transfer Characteristic (K) K= -1 IGAINMOD − IOFFSET mV IAC x (6 - 0.625) 2003/06/25 Preliminary Gain Gain = Champion Microelectronic Corporation ISENSE − IOFFSET IAC Page 7 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO Functional Description Green Mode Function The CM6802 consists of an average current controlled, continuous boost Power Factor Correction (PFC) front end and a synchronized Pulse Width Modulator (PWM) back end. The PWM can be used in either current or voltage mode. In voltage mode, feedforward from the PFC output buss can be used to improve the PWM’s line regulation. In either mode, the PWM stage uses conventional trailing edge duty cycle modulation, while the PFC uses leading edge modulation. This patented leading/trailing edge modulation technique results in a higher usable PFC error amplifier bandwidth, and can significantly reduce the size of the PFC DC buss capacitor. Both PFC Green Mode and PWM Green Mode can be set separately by selecting proper external value of the external components. These 2 external components are CT on the pin 7, RAMP1 pin and the filter resistor at pin 3, ISENSE pin. The synchronized of the PWM with the PFC simplifies the PWM compensation due to the controlled ripple on the PFC output capacitor (the PWM input capacitor). The PWM section of the CM6802 runs at the same frequency as the PFC. In addition to power factor correction, a number of protection features have been built into the CM6802. These include soft-start, PFC overvoltage protection, peak current limiting, brownout protection, duty cycle limiting, and under-voltage lockout. Oscillator (RAMP1) The oscillator frequency is determined by the values of RT and CT, which determine the ramp and off-time of the oscillator output clock: 1 which is the internal clock tRAMP + tDEADTIME frequency, fosc=2 x fpwm= 4 x fpfc fOSC = The Clock period of the oscillator is derived from the following equation: tRAMP = CT x RT x In VREF − 1.25 VREF − 3.75 at VREF = 7.5V: tRAMP = CT x RT x 0.51 2.5V x CT = 450 x CT 5.5mA EXAMPLE: For the application circuit shown in the datasheet, with the oscillator running at: fOSC = 280kHz = 1 tRAMP = 2 x fpwm = 4 x fpfc. Here, fpwm =140KHz and fpfc=70KHz. Selecting standard components values, CT = 1.0nF, and RT = 5.0kΩ 2003/06/25 Preliminary To Disable PFC Green Mode, a 1 Mega ohm resistor is needed between IEAO(pin1) and VREF(pin14). PFC Green Mode Threshold During the light load, VEAO voltage will reduce. When VEAO is less than 0.5V, It will turn off PFC. It has 0.25V hysteresis. If the light load condition continues, the PFC section will stay at pulse skipping condition without audible noise since the input power is minimal because VEAO is around 0.75V. PFC Green Mode Threshold is set by selecting proper Rs which is the resistor of the RC filter at Isense pin. Its typical value is from 30 ohm to 300 ohm. If the Rs value is below 30 ohm, and if a 1 Mega ohm resistor is needed between IEAO(pin1) and VREF(pin14), PFC will not pulse skipping. During the pulse skipping, the reading of the power meter can not be trust. It will need to integrate the real power than average it with the time to get the average power. To further reduce the power and improve the light load efficiency, the values of resistor dividers at VFB and VRMS need to be doubled or tripled. However, it will increase the layout sensitivity. To Disable PFC Green Mode, a 1 Mega ohm resistor is needed between IEAO(pin1) and VREF(pin14). PWM Green Mode Threshold The dead time of the oscillator may be determined using: tDEADTIME = Both Blue Angel and Energy Star spec. can be easily met without shutting off PFC because in CM6802, both PFC and PWM can set the green mode thresholds. Once the green mode threshold is triggered, the section will go to pulse skipping mode. During the light load, PWM section duty cycle also reduces. When the PWM section duty cycle is less than the internal clock duty cycle which is set by the CT at RAMP1, pin 7, the PWM section will start pulse skipping. By selecting the proper CT, user can program the PWM Green Mode Threshold. Usually, CT is 1nF. Power Factor Correction Power factor correction makes a nonlinear load look like a resistive load to the AC line. For a resistor, the current drawn from the line is in phase with and proportional to the line voltage, so the power factor is unity (one). A common class of nonlinear load is the input of most power supplies, which use a bridge rectifier and capacitive input filter fed from the line. The peak-charging effect, which occurs on the input filter capacitor in these supplies, causes brief high-amplitude pulses of current to flow from the power line, rather than a sinusoidal current in phase with the line voltage. Champion Microelectronic Corporation Page 8 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO Such supplies present a power factor to the line of less than one (i.e. they cause significant current harmonics of the power line frequency to appear at their input). If the input current drawn by such a supply (or any other nonlinear load) can be made to follow the input voltage in instantaneous amplitude, it will appear resistive to the AC line and a unity power factor will be achieved. To hold the input current draw of a device drawing power from the AC line in phase with and proportional to the input voltage, a way must be found to prevent that device from loading the line except in proportion to the instantaneous line voltage. The PFC section of the CM6802 uses a boost-mode DC-DC converter to accomplish this. The input to the converter is the full wave rectified AC line voltage. No bulk filtering is applied following the bridge rectifier, so the input voltage to the boost converter ranges (at twice line frequency) from zero volts to the peak value of the AC input and back to zero. By forcing the boost converter to meet two simultaneous conditions, it is possible to ensure that the current drawn from the power line is proportional to the input line voltage. One of these conditions is that the output voltage of the boost converter must be set higher than the peak value of the line voltage. A commonly used value is 385VDC, to allow for a high line of 270VACrms. The other condition is that the current drawn from the line at any given instant must be proportional to the line voltage. Establishing a suitable voltage control loop for the converter, which in turn drives a current error amplifier and switching output driver satisfies the first of these requirements. The second requirement is met by using the rectified AC line voltage to modulate the output of the voltage control loop. Such modulation causes the current error amplifier to command a power stage current that varies directly with the input voltage. In order to prevent ripple, which will necessarily appear at the output of boost circuit (typically about 10VAC on a 385V DC level), from introducing distortion back through the voltage error amplifier, the bandwidth of the voltage loop is deliberately kept low. A final refinement is to adjust the overall gain of the PFC such to be proportional to 1/VIN2, which linearizes the transfer function of the system as the AC input to voltage varies. Since the boost converter topology in the CM6802 PFC is of the current-averaging type, no slope compensation is required. PFC Section Gain Modulator Figure 1 shows a block diagram of the PFC section of the CM6802. The gain modulator is the heart of the PFC, as it is this circuit block which controls the response of the current loop to line voltage waveform and frequency, rms line voltage, and PFC output voltages. There are three inputs to the gain modulator. These are: 2003/06/25 Preliminary 1. A current representing the instantaneous input voltage (amplitude and waveshape) to the PFC. The rectified AC input sine wave is converted to a proportional current via a resistor and is then fed into the gain modulator at IAC. Sampling current in this way minimizes ground noise, as is required in high power switching power conversion environments. The gain modulator responds linearly to this current. 2. A voltage proportional to the long-term RMS AC line voltage, derived from the rectified line voltage after scaling and filtering. This signal is presented to the gain modulator at VRMS. The gain modulator’s output is inversely 2 proportional to VRMS (except at unusually low values of VRMS where special gain contouring takes over, to limit power dissipation of the circuit components under heavy brownout conditions). The relationship between VRMS and gain is called K, and is illustrated in the Typical Performance Characteristics. The output of the voltage error amplifier, VEAO. The gain modulator responds linearly to variations in this voltage. The output of the gain modulator is a current signal, in the form of a full wave rectified sinusoid at twice the line frequency. This current is applied to the virtual-ground (negative) input of the current error amplifier. In this way the gain modulator forms the reference for the current error loop, and ultimately controls the instantaneous current draw of the PFC form the power line. The general for of the output of the gain modulator is: IGAINMOD = IAC × VEAO x 1V VRMS2 (1) More exactly, the output current of the gain modulator is given by: IGAINMOD = K x (VEAO – 0.625V) x IAC Where K is in units of V -1 Note that the output current of the gain modulator is limited around 228.47µA and the maximum output voltage of the gain modulator is limited to 228.47uA x 3.5K=0.8V. This 0.8V also will determine the maximum input power. However, IGAINMOD cannot be measured directly from ISENSE. ISENSE = IGAINMOD-IOFFSET and IOFFSET can only be measured when VEAO is less than 0.5V and IGAINMOD is 0A. Typical IOFFSET is around 60uA. IAC Typically, it has a feedforward resistor, RAC, less than 500K ohm resistor connected between this pin and rectified line input voltage. During the startup condition, it supplies the startup current; therefore, the system does not require additional bleed resistor to start up the chip. Champion Microelectronic Corporation Page 9 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO Selecting RAC for IAC pin IAC pin is the input of the gain modulator. IAC also is a current mirror input and it requires current input. By selecting a proper resistor RAC, it will provide a good sine wave current derived from the line voltage and it also helps program the maximum input power and minimum input line voltage. RAC=Vin peak x 7.9K. For example, if the minimum line voltage is 80VAC, the RAC=80 x 1.414 x 7.9K=894Kohm. Current Error Amplifier, IEAO The current error amplifier’s output controls the PFC duty cycle to keep the average current through the boost inductor a linear function of the line voltage. At the inverting input to the current error amplifier, the output current of the gain modulator is summed with a current which results from a negative voltage being impressed upon the ISENSE pin. The negative voltage on ISENSE represents the sum of all currents flowing in the PFC circuit, and is typically derived from a current sense resistor in series with the negative terminal of the input bridge rectifier. In higher power applications, two current transformers are sometimes used, one to monitor the IF of the boost diode. As stated above, the inverting input of the current error amplifier is a virtual ground. Given this fact, and the arrangement of the duty cycle modulator polarities internal to the PFC, an increase in positive current from the gain modulator will cause the output stage to increase its duty cycle until the voltage on ISENSE is adequately negative to cancel this increased current. Similarly, if the gain modulator’s output decreases, the output duty cycle will decrease, to achieve a less negative voltage on the ISENSE pin. To Disable PFC Green Mode, a 1 Mega ohm resistor is needed between IEAO(pin1) and VREF(pin14). This 1 Mega ohm resistor will reduce the DC gain but it will not impact the performance. Cycle-By-Cycle Current Limiter and Selecting RS The ISENSE pin, as well as being a part of the current feedback loop, is a direct input to the cycle-by-cycle current limiter for the PFC section. Should the input voltage at this pin ever be more negative than –1V, the output of the PFC will be disabled until the protection flip-flop is reset by the clock pulse at the start of the next PFC power cycle. RS is the sensing resistor of the PFC boost converter. During the steady state, line input current x RS = IGAINMOD x 3.5K. Since the maximum output voltage of the gain modulator is IGAINMOD max x 3.5K= 0.8V during the steady state, RS x line input current will be limited below 0.8V as well. Therefore, to choose RS, we use the following equation: RS =0.7V x Vinpeak/(2x Line Input power) For example, if the minimum input voltage is 80VAC, and the maximum input rms power is 200Watt, RS = (0.7V x 80V x 1.414)/(2 x 200) = 0.197 ohm. PFC OVP In the CM6802, PFC OVP comparator serves to protect the power circuit from being subjected to excessive voltages if the load should suddenly change. A resistor divider from the high voltage DC output of the PFC is fed to VFB. When the voltage on VFB exceeds 2.75V, the PFC output driver is shut down. The PWM section will continue to operate. The OVP comparator has 250mV of hysteresis, and the PFC will not restart until the voltage at VFB drops below 2.50V. The VFB power components and the CM6802 are within their safe operating voltages, but not so low as to interfere with the boost voltage regulation loop. Also, VCC OVP can be served as a redundant PFCOVP protection. VCC OVP threshold is 19.4V with 1.5V hysteresis. Figure 1. PFC Section Block Diagram 2003/06/25 Preliminary Champion Microelectronic Corporation Page 10 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO Error Amplifier Compensation The PWM loading of the PFC can be modeled as a negative resistor; an increase in input voltage to the PWM causes a decrease in the input current. This response dictates the proper compensation of the two transconductance error amplifiers. Figure 2 shows the types of compensation networks most commonly used for the voltage and current error amplifiers, along with their respective return points. The current loop compensation is returned to VREF to produce a soft-start characteristic on the PFC: as the reference voltage comes up from zero volts, it creates a differentiated voltage on IEAO which prevents the PFC from immediately demanding a full duty cycle on its boost converter. PFC Voltage Loop There are two major concerns when compensating the voltage loop error amplifier, VEAO; stability and transient response. Optimizing interaction between transient response and stability requires that the error amplifier’s open-loop crossover frequency should be 1/2 that of the line frequency, or 23Hz for a 47Hz line (lowest anticipated international power frequency). The gain vs. input voltage of the CM6802’s voltage error amplifier, VEAO has a specially shaped non-linearity such that under steady-state operating conditions the transconductance of the error amplifier is at a local minimum. Rapid perturbation in line or load conditions will cause the input to the voltage error amplifier (VFB) to deviate from its 2.5V (nominal) value. If this happens, the transconductance of the voltage error amplifier will increase significantly, as shown in the Typical Performance Characteristics. This raises the gain-bandwidth product of the voltage loop, resulting in a much more rapid voltage loop response to such perturbations than would occur with a conventional linear gain characteristics. The Voltage Loop Gain (S) ∆VOUT ∆VFB ∆VEAO * * ∆VEAO ∆VOUT ∆VFB PIN * 2.5V ≈ * GMV * ZCV 2 VOUTDC * ∆VEAO * S * CDC = ZCV: Compensation Net Work for the Voltage Loop GMv: Transconductance of VEAO PIN: Average PFC Input Power VOUTDC: PFC Boost Output Voltage; typical designed value is 380V. CDC: PFC Boost Output Capacitor PFC Current Loop The current amplifier, IEAO compensation is similar to that of the voltage error amplifier, VEAO with exception of the choice of crossover frequency. The crossover frequency of the current amplifier should be at least 10 times that of the 2003/06/25 Preliminary voltage amplifier, to prevent interaction with the voltage loop. It should also be limited to less than 1/6th that of the switching frequency, e.g. 16.7kHz for a 100kHz switching frequency. The Current Loop Gain (S) ∆VISENSE ∆DOFF ∆IEAO * * ∆DOFF ∆IEAO ∆ISENSE VOUTDC * RS ≈ * GMI * ZCI S * L * 2.5V = ZCI: Compensation Net Work for the Current Loop GMI: Transconductance of IEAO VOUTDC: PFC Boost Output Voltage; typical designed value is 380V and we use the worst condition to calculate the ZCI RS: The Sensing Resistor of the Boost Converter 2.5V: The Amplitude of the PFC Leading Modulation Ramp L: The Boost Inductor There is a modest degree of gain contouring applied to the transfer characteristic of the current error amplifier, to increase its speed of response to current-loop perturbations. However, the boost inductor will usually be the dominant factor in overall current loop response. Therefore, this contouring is significantly less marked than that of the voltage error amplifier. This is illustrated in the Typical Performance Characteristics. ISENSE Filter, the RC filter between RS and ISENSE : There are 3 purposes to add a filter at ISENSE pin: 1.) Protection: During start up or inrush current conditions, it will have a large voltage cross Rs which is the sensing resistor of the PFC boost converter. It requires the ISENSE Filter to attenuate the energy. 2.) To reduce L, the Boost Inductor: The ISENSE Filter also can reduce the Boost Inductor value since the ISENSE Filter behaves like an integrator before going ISENSE which is the input of the current error amplifier, IEAO. 3.) By selecting the proper Rs, it can change the PFC Green Mode threshold. Typical value is from 50 ohm (No Skipping) to 100 ohm. The ISENSE Filter is a RC filter. The resistor value of the ISENSE Filter is between 100 ohm and 50 ohm because IOFFSET x the resistor can generate an offset voltage of IEAO. By selecting RFILTER equal to 50 ohm will keep the offset of the IEAO less than 5mV. Usually, we design the pole of ISENSE Filter at fpfc/6, one sixth of the PFC switching frequency. Therefore, the boost inductor can be reduced 6 times without disturbing the stability. Therefore, the capacitor of the ISENSE Filter, CFILTER, will be around 283nF. Champion Microelectronic Corporation Page 11 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO PWM Section Pulse Width Modulator The PWM section of the CM6802 is straightforward, but there are several points which should be noted. Foremost among these is its inherent synchronization to the PFC section of the device, from which it also derives its basic timing. The PWM is capable of current-mode or voltage-mode operation. In current-mode applications, the PWM ramp (RAMP2) is usually derived directly from a current sensing resistor or current transformer in the primary of the output stage, and is thereby representative of the current flowing in the converter’s output stage. DCILIMIT, which provides cycle-by-cycle current limiting, is typically connected to RAMP2 in such applications. For voltage-mode, operation or certain specialized applications, RAMP2 can be connected to a separate RC timing network to generate a voltage ramp against which VDC will be compared. Under these conditions, the use of voltage feedforward from the PFC buss can assist in line regulation accuracy and response. As in current mode operation, the DC ILIMIT input is used for output stage overcurrent protection. No voltage error amplifier is included in the PWM stage of the CM6802, as this function is generally performed on the output side of the PWM’s isolation boundary. To facilitate the design of optocoupler feedback circuitry, an offset has been built into the PWM’s RAMP2 input which allows VDC to command a zero percent duty cycle for input voltages below 1.25V. 2003/06/25 Preliminary PWM Current Limit The DC ILIMIT pin is a direct input to the cycle-by-cycle current limiter for the PWM section. Should the input voltage at this pin ever exceed 1V, the output flip-flop is reset by the clock pulse at the start of the next PWM power cycle. Beside, the cycle-by-cycle current, when the DC ILIMIT triggered the cycle-by-cycle current, it also softly discharge the voltage of soft start capacitor. It will limit PWM duty cycle mode. Therefore, the power dissipation will be reduced during the dead short condition. VIN OK Comparator The VIN OK comparator monitors the DC output of the PFC and inhibits the PWM if this voltage on VFB is less than its nominal 2.45V. Once this voltage reaches 2.45V, which corresponds to the PFC output capacitor being charged to its rated boost voltage, the soft-start begins. PWM Control (RAMP2) When the PWM section is used in current mode, RAMP2 is generally used as the sampling point for a voltage representing the current on the primary of the PWM’s output transformer, derived either by a current sensing resistor or a current transformer. In voltage mode, it is the input for a ramp voltage generated by a second set of timing components (RRAMP2, CRAMP2), that will have a minimum value of zero volts and should have a peak value of approximately 5V. In voltage mode operation, feedforward from the PFC output buss is an excellent way to derive the timing ramp for the PWM stage. Champion Microelectronic Corporation Page 12 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO Soft Start Start-up of the PWM is controlled by the selection of the external capacitor at SS. A current source of 20µA supplies the charging current for the capacitor, and start-up of the PWM begins at 1.25V. Start-up delay can be programmed by the following equation: CSS = tDELAY x 20 µA 1.25V where CSS is the required soft start capacitance and the tDEALY is the desired start-up delay. It is important that the time constant of the PWM soft-start allow the PFC time to generate sufficient output power for the PWM section. The PWM start-up delay should be at least 5ms. Solving for the minimum value of CSS: CSS = 5ms x 20 µA = 80nF 1.25V Caution should be exercised when using this minimum soft start capacitance value because premature charging of the SS capacitor and activation of the PWM section can result if VFB is in the hysteresis band of the VIN OK comparator at start-up. The magnitude of VFB at start-up is related both to line voltage and nominal PFC output voltage. Typically, a 1.0µF soft start capacitor will allow time for VFB and PFC out to reach their nominal values prior to activation of the PWM section at line voltages between 90Vrms and 265Vrms. 2003/06/25 Preliminary Generating VCC After turning on CM6802 at 15V, the operating voltage can vary from 10V to 19.4V. The threshold voltage of VCC OVP comparator is 19.4V. The hysteresis of VCC OVP is 1.5V. When VCC see 19.4V, PFCOUT will be low, and PWM section will not be disturbed. That’s the two ways to generate VCC. One way is to use auxiliary power supply around 15V, and the other way is to use bootstrap winding to self-bias CM6802 system. The bootstrap winding can be either taped from PFC boost choke or from the transformer of the DC to DC stage. The ratio of winding transformer for the bootstrap should be set between 18V and 15V. A filter network is recommended between VCC (pin 13) and bootstrap winding. The resistor of the filter can be set as following. RFILTER x IVCC ~ 2V, IVCC = IOP + (QPFCFET + QPWMFET ) x fsw IOP = 3mA (typ.) If anything goes wrong, and VCC goes beyond 19.4V, the PFC gate (pin 12) drive goes low and the PWM gate drive (pin 11) remains function. The resistor’s value must be chosen to meet the operating current requirement of the CM6802 itself (3mA, max.) plus the current required by the two gate driver outputs. Champion Microelectronic Corporation Page 13 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO EXAMPLE: With a wanting voltage called, VBIAS ,of 18V, a VCC of 15V and the CM6802 driving a total gate charge of 90nC at 100kHz (e.g. 1 IRF840 MOSFET and 2 IRF820 MOSFET), the gate driver current required is: IGATEDRIVE = 100kHz x 90nC = 9mA RBIAS = VBIAS − VCC ICC + IG RBIAS = 18V − 15V 5mA + 9mA Choose RBIAS = 214Ω The CM6802 should be locally bypassed with a 1.0µF ceramic capacitor. In most applications, an electrolytic capacitor of between 47µF and 220µF is also required across the part, both for filtering and as part of the start-up bootstrap circuitry. In case of leading edge modulation, the switch is turned OFF right at the leading edge of the system clock. When the modulating ramp reaches the level of the error amplifier output voltage, the switch will be turned ON. The effective duty-cycle of the leading edge modulation is determined during OFF time of the switch. Figure 5 shows a leading edge control scheme. One of the advantages of this control technique is that it required only one system clock. Switch 1(SW1) turns off and switch 2 (SW2) turns on at the same instant to minimize the momentary “no-load” period, thus lowering ripple voltage generated by the switching action. With such synchronized switching, the ripple voltage of the first stage is reduced. Calculation and evaluation have shown that the 120Hz component of the PFC’s output ripple voltage can be reduced by as much as 30% using this method. Leading/Trailing Modulation Conventional Pulse Width Modulation (PWM) techniques employ trailing edge modulation in which the switch will turn on right after the trailing edge of the system clock. The error amplifier output is then compared with the modulating ramp up. The effective duty cycle of the trailing edge modulation is determined during the ON time of the switch. Figure 4 shows a typical trailing edge control scheme. 2003/06/25 Preliminary Champion Microelectronic Corporation Page 14 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO +12V Return +12V OUT APPLICATION CIRCUIT (Current Mode) R18 R22 R25 C22 R26 C21 C23 +12V R24 C24 U3 R23 U2 L2 D11A D11B T2B R16 T2C C10 T2A +382V TP1 R13 D6 D5 Q5 RAMP2 R9 C9 D4 C8 R11 R20B C17 C14 R20A Q3 D7 C13 R30 R19 D15 C17 C16 R14 R17 C20 T1A R15 C15 VCC R30 R29 REF Q2 D10 T1B C25 R10 R6 R7A C31 R7B R8 D9 L1 10 11 12 9 RAMP2 ILIMIT C11 8 GND RAMP1 7 VDC PWM-OUT 6 13 VCC PFC-OUT SS VRMS 5 4 14 I-SENSE VREF 3 16 1 VFB R12 Q1 VEAO C7 C12 D1 IAC CM6802 C4 IEAO C6 D2 2 D3 15 C5 R28 D8 R21 C30 C18 VDC R1A R1B R2A R2B C19 R28 R3 C2 C33 + R4 D13 C3 C32 R5E - D12 D14 R5D C1 R5C R5B VIN R5A AC 2003/06/25 Preliminary Champion Microelectronic Corporation Page 15 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO APPLICATION CIRCUIT (Voltage Mode) R5 IVIN_EMC EMC FILTER L2 R3 L3 RT1 IVIN D4 PFC_VIN IVIN L1 IL1 PFC_VIN IAC D5 Q3 VIN AC R2 C3 C8 C2 R1 R10 R12 R14 C33 100n D12 Q1 Q2N2222 PFC_DC R13 Q2 Q2N904 R15 R18 D6 PFC_Vout IC10 D10 R26 18k 22 R16A MUR1100 C10 R23 R24 75 22 R25 10k C23 470p R17A VFB D7 C55A C41 1N4002 PFC_Vout Q4 R22 1N4148 R11 D5 IBOOT R65A C30 1N4002 R58 R64 R59 C43 IEAO U2 CM6802 1 IEAO VEAO 2 ISENSE R60 3 VRMS 4 C46 SS R66 VDC C47 VREF 5 6 7 C44 R56 R57 C45 8 VCC IAC SS GND ILIMIT VREF VCC 12 PFC-OUT VDC PWM-OUT RAMP2 VREF 13 VCC RAMP1 VEAO 14 I-SENSE VREF VRMS 16 15 VFB C52 C53 1u 100n VCC C54 11 10 PWM_OUT R63 ZD2 9 C57 C56 R62 C48 C49 ILIMIT ILIMIT C50 R61 470 C51 R44 C4 ISO1 VDC C14 PWM_IN PFC_Vout R34 C38 C7 10n R27 100k C22 10n 10n 4.7 R49 IL4 D9A D8 D13 MUR1100 T1 D9B L4 L5 R35 4.7 R46 PWM_Vout IC17 IC18 C17 C18 C40 R43 C39 ILOAD C19 R45 PWM_Rload 500m U1 CM431 MUR1100 C22 10n R48 C15 10n VCC IBIAS C34 100n D16 Q6 Q2N2222 PWM_DC PFC_OUT R32A R32 VCC 1N4148 Q7 Q2N904 C31 R33 R28 T 2:3 22 Q3 R29 10k ILIMIT R31 ZD1 6.8V 2003/06/25 Preliminary Champion Microelectronic Corporation Page 16 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO PACKAGE DIMENSION 16-PIN PDIP (P16) PIN 1 ID θ θ 16-PIN SOP (S16) PIN 1 ID θ θ 2003/06/25 Preliminary Champion Microelectronic Corporation Page 17 CM6802 NO BLEED RESISTOR GREEN MODE PFC/PWM CONTROLLER COMBO IMPORTANT NOTICE Champion Microelectronic Corporation (CMC) reserves the right to make changes to its products or to discontinue any integrated circuit product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the information being relied on is current. A few applications using integrated circuit products may involve potential risks of death, personal injury, or severe property or environmental damage. CMC integrated circuit products are not designed, intended, authorized, or warranted to be suitable for use in life-support applications, devices or systems or other critical applications. Use of CMC products in such applications is understood to be fully at the risk of the customer. In order to minimize risks associated with the customer’s applications, the customer should provide adequate design and operating safeguards. HsinChu Headquarter Sales & Marketing 5F, No. 11, Park Avenue II, Science-Based Industrial Park, HsinChu City, Taiwan 11F, No. 306-3, Sec. 1, Ta Tung Rd., Hsichih, Taipei Hsien 221 Taiwan, R.O.C. T E L : +886-3-567 9979 F A X : +886-3-567 9909 http://www.champion-micro.com T E L : +886-2-8692 1591 F A X : +886-2-8692 1596 2003/06/25 Preliminary Champion Microelectronic Corporation Page 18