CURRENT 1.0 Ampere VOLTAGE 50 to 400 Volts ES1A THRU ES1J Features · For surface applications in order to optimize board space · Low profile package · Built-in strain relief, ideal for automated placement · Super fast recovery time · Glass passivated junction · Plastic package has Unerwrites Laboratory Flammability Classification 94V-0 · Ideally suited for use in very high frequency switching power supplies, inverters and as free wheeling diodes · Low forward voltage drop · Glass passivated chip junction · High temperature soldering guaranteed : 250℃/10 seconds, at terminals DO-214AC (SMA) 0.110(2.79) 0.100(2.54) 0.058(1.47) 0.052(1.32) 0.177(4.50) 0.157(3.99) 0.012(0.31) 0.006(0.15) 0.090(2.29) 0.078(1.98) Mechanical Data · Case : JEDEC SMA(DO-214AC) molded plastic body · Terminals : Plated axial lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.002 ounce, 0.064 gram 0.005(0.127) MAX. 0.060(1.52) 0.030(0.76) 0.208(5.28) 0.194(4.93) Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols ES1A ES1B ES1C ES1D ES1G ES1J Units Maximum recurrent peak reverse voltage VRRM 50 100 150 200 400 600 Volts Maximum RMS voltage VRMS 35 70 105 140 380 420 Volts Maximum DC blocking voltage VDC 50 100 150 200 400 600 Volts Maximum average forward rectified current at TL=120℃ I(AV) 1.0 Amp Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 30.0 Amps Maximum instantaneous forward voltage at 1.0A Maximum reverse current at rated voltage TA=25℃ TA=100℃ Maximum reverse recovery time (Note 1) Typical thermal resistance (Note 3) Typical junction capacitance (Note 2) Operating unction and storage temperature range VF IR Trr 0.95 1.25 5.0 100 Volts μA 35 ns RθJL RθJA 35.0 85.0 ℃/W CJ TJ TSTG 7.0 pF -55 to +150 ℃ Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. (3) P.C.B mounted on 0.2×0.2"(5.0×5.0mm) copper pad areas RATINGS AND CHARACTERISTIC CURVES ES1A THRU ES1J FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG.1-FORWARD CURRENT DERATING CURVE 30 1 8.3ms SINGLE HALF SINE WAVE 25 0.8 PEAK FORWARD SURGE CURRENT(AMPERES) AVERAGE FORWARD CURRENT AMPERES 1.2 RESISTIVE OR INDUCTIVE LOAD 0.2X0.2"(5.0X5.0mm) COPPER PAD AREAS 0.6 0.4 0.2 (JEDEC Method) at TL=120℃ 20 15 10 5 0 0 80 90 100 110 120 130 140 1 150 10 NUMBER OF CYCLES AT 60Hz LEAD TEMPERATURE (℃) FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4-TYPICAL REVERSE CHARACTERISTICS 50 1000 10 INSTANTANEOUS REVERSE CURRENT ,(mA) INSTANTANEOUS FORWARD CURRENT(AMPERES) 100 1 0.1 TJ=25℃ PULSE WIDTH=300mS 1% DUTY CYCLE 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 100 TJ=125℃ 10 1 TJ=75℃ TJ=25℃ 0.1 1.8 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) FIG.6-TYPICAL TRANSIENT THERMAL IMPEDANCE FIG.5-TYPICAL JUNCTION CAPACITANCE 100 12 TJ=25℃ f=1.0MHz Vsig=50mVp-P 10 8 6 4 2 0 0.1 1 10 REVERSE VOLTAGE. VOLTS 100 TRANSIENT THERMAL IMPEDANCE, ℃/W JUNCTIOIN CAPACITANCE(pF) 14 MOUNTED ON 0.2X0.2"(5X7mm) COPPER PAD AREAS 10 1 0.1 1 10 T, PULSE DURATION ,sec. 100 RATINGS AND CHARACTERISTIC CURVES ES1A THRU ES1J FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG.1-FORWARD CURRENT DERATING CURVE 30 1 8.3ms SINGLE HALF SINE WAVE 25 0.8 PEAK FORWARD SURGE CURRENT(AMPERES) AVERAGE FORWARD CURRENT AMPERES 1.2 RESISTIVE OR INDUCTIVE LOAD 0.2X0.2"(5.0X5.0mm) COPPER PAD AREAS 0.6 0.4 0.2 (JEDEC Method) at TL=120℃ 20 15 10 5 0 0 80 90 100 110 120 130 140 1 150 10 NUMBER OF CYCLES AT 60Hz LEAD TEMPERATURE (℃) FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4-TYPICAL REVERSE CHARACTERISTICS 50 1000 10 INSTANTANEOUS REVERSE CURRENT ,(mA) INSTANTANEOUS FORWARD CURRENT(AMPERES) 100 1 0.1 TJ=25℃ PULSE WIDTH=300mS 1% DUTY CYCLE 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 100 TJ=125℃ 10 1 TJ=75℃ TJ=25℃ 0.1 1.8 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 0.01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) FIG.6-TYPICAL TRANSIENT THERMAL IMPEDANCE FIG.5-TYPICAL JUNCTION CAPACITANCE 100 12 TJ=25℃ f=1.0MHz Vsig=50mVp-P 10 8 6 4 2 0 0.1 1 10 REVERSE VOLTAGE. VOLTS 100 TRANSIENT THERMAL IMPEDANCE, ℃/W JUNCTIOIN CAPACITANCE(pF) 14 MOUNTED ON 0.2X0.2"(5X7mm) COPPER PAD AREAS 10 1 0.1 1 10 T, PULSE DURATION ,sec. 100