2mm LED CBI® Circuit Board Indicator (DIN 41494 Compatible), Bi-Level HOUSING TYPE 0 WITHOUT PINS 2.50 [.095] 8.60 [.339] 1.52 ±.20 [.060 ±.008] 571-01xx HOUSING TYPE 1 WITH PINS 13.72 [.540] 1.37 [.054] 5.08 [.20..0] 1.27 [.050] MAX 2.54 ±.05 [.100 ±.002] TYP (3) 5.08 [.200] 1.80 ±.20 [.071 ±.008] 3.81 [.150] 3.81 [.150] 0.38 [.015] 2.54 [.100] 3.00 ±.25 [.118 ±.010] 0.38 [.015] 0.41 [.016] Ø 1.02 ±.05 [.040 ±.002] TYP (4) 2.54 [.100] CATHODE 0.46 [.018] 4.83 [.190] 2.54 [.100] RECOMMENDED PC BOARD HOLE PATTERN CATHODE 2.54 [.100] 2.54 [.100] TOP LED Except where noted Housing Type 1 dimensions are the same as Housing Type 0 Dimensions in mm [inches] Features PART NO. WITHOUT PINS • Designed to accommodate DIN 41494 • Multiple CBIs form horizontal LED arrays on 2.54mm 571-0111 571-0112 571-0122 571-0132 571-0133 * Top-Bottom LED PART NO. WITH PINS Red-Red Red-Green Green-Green Yellow-Green Yellow-Yellow 571-0111-100 571-0112-100 571-0122-100 571-0132-100 571-0133-100 * Top-Bottom LED Red-Red Red-Green Green-Green Yellow-Green Yellow-Yellow • • • • (0.100”) center-lines High Contrast, UL 94 V-0 rated, black housing Oxygen index: 32% Polymer content: PBT, 0.290 g Housing stand-offs facilitate PCB cleaning • Solderability per MIL-STD-202F, method 208F • LEDs are safe for direct viewing per IEC 825-1, EN-60825-1 Tolerance note: As noted, otherwise: • LED Protrusion: ±0.04 mm [±0.016] • CBI Housing: ±0.02mm[±0.008] Top LED Color Custom Combinations Array Code 5 7 1 – 0 1 x x – 1 0 x LED Type Bottom LED Color COLOR* Arrays available. See Part Number ordering code. PART NUMBER ORDERING CODE Series COLOR* • Contact factory for information on custom color combinations. EXAMPLE Number of Bi-Levels in array 1) With pins Single unit with pins LED colors: 0) Blank, 1) Red, 2) Green, 3) Yellow 5 7 1 – 0 1 x x – 1 0 0 1 0 2 –10x Suffix required only when ordering single units with pins or arrays Two bi-levels in an array (4 LEDs) See LED data sheet for additional information See Page 3-17 and 3-18 for Reference Only LED Drive Circuit Examples See Page 3-20 for Pin Out Typical Operating Characteristics (TA = 25°C) GENERAL PURPOSE Part Number Color Peak Wavelength nm IV* mcd V F ** Volts Viewing Angle 2Θ Θ1/2 LED Data sheet Page # 571-01xx Red Green Yellow 635 565 585 12.6 8.7 12.6 2 2.1 2.1 38° 38° 38° 521-9630 521-9632 521-9631 3-13 3-13 3-13 * IF = 10mA 3-10 ** IF = 20mA Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com 2mm Discrete LED Diffused 521-9630, -9631, -9632 CATHODE I.D. 2.40 [.095] 2.90 [.114] 25.40 [1.00] MIN CATHODE 3.30 [.13] .45 [.018] TYP 1.80 [.071] R 1.65 [.065] 1.52 [.060] .40 [.016] TYP 1.00 [.04] MIN 2.54 [.10] NOM PART NO. 521-9630 521-9631 521-9632 COLOR Red Yellow Green 1.50 [.059] MAX 3.30 [.130] 3 Dimensions in mm [inches] Red Yellow Green -9630 -9631 -9632 Power Dissipation (mW) 100 60 100 Forward Current (mA) 30 20 30 .4 .25 .4 120 80 120 Operating Temperature (°C) -55/+100 -55/+100 -55/+100 Storage Temperature (°C) -55/+100 -55/+100 -55/+100 ABSOLUTE MAXIMUM RATINGS (TA=25°C) Derating (mA/°C) From 25°C Peak Current (mA) Pulse width = 10µs Soldering Temperature 260°C, 5 seconds, 1.6 mm from case Red Yellow Green OPERATING CHARACTERISTICS (TA=25°C) -9630 -9631 -9632 Luminous Intensity (mcd) IF=10mA Min. Typical 3.7 12.6 3.7 12.6 2.5 8.7 Peak Wavelength (nm) λ Peak Typical 635 585 565 Viewing Angle (2Θ Θ1/2) Typical 38° 38° 38° Forward Voltage (V) IF=20mA Typical Max. 2 2.8 2.1 2.8 2.1 2.8 Reverse Voltage (V), IR=100µA Min. 5 5 5 Θ 1¼2is the off axis angle at which the luminous intensity is half the axial luminous intensity Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com 3-13