EM MICROELECTRONIC - MARIN SA EM65XX EM65XX Datasheet MFP versions of EM66XX (Mask Rom) EM Microelectronic-Marin SA Tel +41 32 755 51 11 Fax +41 32 755 54 03 http://www.emmicroelectronic.com Copyright © 2005, EM Microelectronic-Marin SA 1 www.emmicroelectronic.com EM65XX Table of Contents 1. GENERAL ........................................................................................................................ 3 ORDERING INFORMATION .................................................................................................. 3 2. EM6503 ............................................................................................................................ 4 3. EM6504 ............................................................................................................................ 7 4. EM6505 .......................................................................................................................... 11 5. EM6517 .......................................................................................................................... 15 6. EM6520 .......................................................................................................................... 16 7. EM6521 .......................................................................................................................... 17 8. EM6522 .......................................................................................................................... 18 9. EM6540 .......................................................................................................................... 19 10. PACKAGE DIMENSIONS ........................................................................................... 23 11. ORDERING INFORMATION ....................................................................................... 28 Copyright © 2005, EM Microelectronic-Marin SA 2 www.emmicroelectronic.com EM65XX 1. General The EM65xx is the Multiple Field Programmable Version of the corresponding EM66xx 4 bit Microcontroller The program ROM is replaced by non volatile memory, which can be programmed up to 100 times. Functionally, the two types are equal, except the metal options which are defined in the following pages. Electrically, the MFP ‘s work above 2.0V and need more current, see the tables in the following description. The programming is done with the EM MFP programmer, either by putting the device onto the programmer or connecting it with the connector at the back to your board. Qin EM MFP Programmer Qout Test Vreg Vdd EM65xx Vss Your PCB Handling Procedures This devices have built-in protection against high static voltages or electric fields; however, anti-static precautions should be taken as for any other CMOS component. Unless otherwise specified, proper operation can only occur when all terminal voltages are kept within the supply voltage range. Absolute maximum ratings Min. Max. Units Power supply VDD-VSS - 0.2 + 5.5 V Input voltage VSS - 0.2 VDD+0.2 V Storage temperature - 40 + 125 °C Electrostatic discharge to MIL-STD-883C method 3015 -2000 +2000 V Maximum soldering conditions 10s x 250°C Stresses above these listed maximum ratings may cause permanent damage to the device. Exposure beyond specified electrical characteristics may affect device reliability or cause malfunction. Ordering Information The MFP’s should be used for engineering purposes only. No volume production must be planned. Copyright © 2005, EM Microelectronic-Marin SA 3 www.emmicroelectronic.com EM65XX 2. EM6503 Input/Output ports All ports if selected as outputs are Push-pull outputs (driving high / low). Inputs are not blocked when Output is selected and Outputs comes Hi-Z in Sleep mode. Input/Output Port Options Pull-Up Yes / No Pull-Down Yes / No 0 A0 A1 A2 A3 B0 B1 B2 B3 C0 C1 C2 C3 D0 D1 D2 D3 PA0 input PA1 input PA2 input PA3 input PB0 In/Out PB1 In/Out PB2 In/Out PB3 In/Out PC0 In/Out PC1 In/Out PC2 In/Out PC3 In/Out PD0 In/Out PD1 In/Out PD2 In/Out PD3 In/Out Nch-open drain Input blocked Yes / No when Output Yes / No 4 5 1 NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO Output Hi-Z in SLEEP mode Yes / No 6 YES YES YES YES YES YES YES YES YES YES YES YES PortA reset No PortA reset option is selected NO PortA reset combination RA PortA RESET 0 X PA0 & PA1 logic AND input reset PA0 & PA1 & PA2 logic AND input reset 2 1 PA0 & PA1 & PA2 & PA3 logic AND input reset 3 Supply Voltage Level Detector T= -10°C to 60°C Symb. VSVLD1 VSVLD2 VSVLD3 Parameter SVLD voltage Level1 SVLD voltage Level2 SVLD voltage Level3 Copyright © 2005, EM Microelectronic-Marin SA Min. 2.25 3.15 3.87 Typ. 2.5 3.5 4.3 4 Max. 2.75 3.85 4.73 Unit V V V www.emmicroelectronic.com EM65XX Electrical specifications Standard Operating Conditions Parameter Temperature VDD VSS CVreg fq Rqs CL df/f Value 0°C...+60°C +2.0 ...+5.0V 0 V (reference) min. 100nF 32768 Hz 35 kOhm 8.2pF +/- 30 ppm Description Vreg logic supply capacitor nominal frequency typical quartz serial resistor typical quartz load capacitance quartz frequency tolerance DC characteristics - Power Supply Pins VDD=3.0V, T=25°C (note4) (unless otherwise specified), Vreg not shorted to VDD Parameter Conditions Symb. ACTIVE Supply Current ACTIVE Supply Current (in active mode) STANDBY Supply Current STANDBY Supply Current (in Halt mode) SLEEP Supply Current SLEEP Supply Current (SLEEP =1) Regulated Voltage +25°C (note2) (note2) (note3) 0°C...+60°C +25°C (note3) 0°C...+60°C +25°C (note3) 0°C...+60°C 0°C...+60°C IVDDa Min. IVDDa IVDDh IVDDh IVDDs IVDDs Vreg Typ. (note1) 9.0 Max. 15.0 Unit µA 1.7 20.0 4.0 µA µA 0.7 7.0 2.0 µA µA 5.0 2.5 µA V 1.6 VDD=5.0V, T=25°C (note4) (unless otherwise specified), Vreg not shorted to VDD Parameter Conditions Symb. ACTIVE Supply Current ACTIVE Supply Current (in active mode) STANDBY Supply Current STANDBY Supply Current (in Halt mode) SLEEP Supply Current SLEEP Supply Current (SLEEP =1) +25°C (note2) (note2) (note3) 0°C...+60°C +25°C (note3) 0°C...+60°C +25°C (note3) 0°C...+60°C IVDDa Min. Typ. (note1) 13.0 Max. 18.0 Unit µA IVDDa IVDDh 1.8 20.0 5.0 µA µA IVDDh IVDDs 0.7 10.0 2.0 µA µA 5.0 µA IVDDs Note1: For current measurement typical quartz described in Operating Conditions is used. All I/O pins without internal Pull Up/Down are pulled to VDD externally. Note2: Test loop with successive writing and reading of two different addresses with an inverted values (five instructions should be reserved for this measurement), Note3: NOT tested at temperature if delivered in chip form. Note4: Test conditions for ACTIVE and STANDBY Supply current mode are: Qin = external square wave, from rail to rail of Vreg (regulated voltage) with 100nF capacitor on Vreg. fQin = 33kHz. Copyright © 2005, EM Microelectronic-Marin SA 5 www.emmicroelectronic.com EM65XX Today’s Versions EM6503P02 I/O’s VLD levels Remarks As defined As defined - X=4606 PC3 X=3828 PC2 X=4082 PD1 X=1648 PD3 X=405 PD2 X=1026 All dimensions in Microns PD0 X=2369 Die, pad location and size Y=4204 Y=3991 PC1 Y=3705 NC RESET Y=3435 NC PC0 Y=2731 STB/RST Y=2477 VSS Y=2203 OscIn Y=1997 VddCA Y=2719 Vbat Y=2465 EM6503 CHIP SIZE is X = 5029 microns by Y = 4419 microns or X = 198 mils by Y = 174 mils heith of the die Z = 11 mils OscOut Y=1221 X=4633 PA0 Y=1469 PA1 Y=1205 PA2 Y=941 X=4817 TEST X=4545 PB3 X=3432 PB2 X=2901 PB1 X=2370 PA3 X=522 X=0 X=−212 PB0 X=1839 Y=0 Y=−215 Package SO24 package. See dimensions in section 10. Copyright © 2005, EM Microelectronic-Marin SA 6 www.emmicroelectronic.com EM65XX 3. EM6504 Input / Output ports The EM6504 - MFP version of EM6604 has no input pull-up or pull-down resistors. User has to put an external resistor if needed in the application. In metal ROM version (EM6604) user can select resistors described in Electrical parameters and Input/Output port mask option. For PortC Input/Output selection there is an additional register in EM6504 (register PcOE at address 60hex) instead of metal mask in EM6604. For PortA Rising/Falling Interrupt edge selection there is an additional register in EM6504 (register PaIRQedge at address 63hex) instead of metal mask in EM6604. PortC Input/Output metal options are replaced by register PcOE in EM6504 MFP version. This register is described below. Input / Output ports option Clocked Output Clocked PullPull-Down Pull-Up Pull-Up Down R= R = 30k? R = Pull-Down Pull-Up R = 30k? 150k? 150k? R > 1M? R > 1M? 0 A0 A1 A2 A3 C0 C1 C2 C3 PA0 input PA1 input PA2 input PA3 input PC0 In/Out PC1 In/Out PC2 In/Out PC3 In/Out 1 2 3 4 5 6 PCoe0 PCoe1 PCoe2 PCoe3 No Input Pull-Up or PullDown 7 x x x x x x x x the MFP EM6504 option selection is showed by « x » and « PCoex » PortA interrupt edge This metal options are replaced by register PaIRQedge in EM6504 MFP version. The register is described below. PortA interrupt edge option I0 I1 I2 I3 PA0 – IRQ PA1 – IRQ PA2 – IRQ PA3 – IRQ Interrupt on Input’s rising edge 8 PA0r = 1 PA1r = 1 PA2r = 1 PA3r = 1 Interrupt on Input’s falling edge 9 PA0r = 0 PA1r = 0 PA2r = 0 PA3r = 0 the MFP EM6504 PortA interrupt edge option is selected by values in register PaIRQedge Copyright © 2005, EM Microelectronic-Marin SA 7 www.emmicroelectronic.com EM65XX Watchdog metal option The Watch-Dog timer is always active. Watchdog metal option Watch-Dog timer ACTIVE x W0 WD timer Watch-Dog timer INACTIVE Supply Voltage Level Detector T= -10°C to 60°C Symb. VSVLD1 Parameter SVLD voltage Level1 Min. 2.02 Typ. 2.30 Max. 2.38 Unit V Additional registers In EM6504 there are two additional registers replacing metal options in EM6604. Register name add add hex dec PaIRQedge 63 99 reset value b'3210 0000 PcOE 60 96 0000 write_bits read_bits Read/Write_bits 0: PA0r 1: PA1r 2: PA2r 3: PA3r 0: PCoe0 1: PCoe1 2: PCoe2 3: PCoe3 Remarks Port A IRQ edge 1 = rising 0 = falling Port C Output Enable 1 = output 0 = input Because these two registers replace the metal option in EM6604 it is advised that they are written as first two instructions in the main program and that they are executed only once. They should not be changed later in the program because the metal options in EM6604 are fixed. Electrical specifications Standard Operating Conditions Parameter Temperature VDD VSS CVDDCA fq Rqs CL df/f Value 0°C...+60°C +2.0 ...+5.0V 0 V (reference) min. 100nF (note1) 32768 Hz 35 kOhm 8.2pF +/- 30 ppm Description Vreg switched logic supply capacitor nominal frequency typical quartz serial resistor typical quartz load capacitance quartz frequency tolerance Note1: This capacitor maintains the Regulated Supply to the core when the core has been isolated by the internal Supply switch during driving the high current outputs. The user should be aware that the selection of this capacitor will dictate the time that the core can be isolated. Copyright © 2005, EM Microelectronic-Marin SA 8 www.emmicroelectronic.com EM65XX DC characteristics - Power Supply Pins VDD=3.0V, T=25°C (unless otherwise specified) Parameter ACTIVE Supply Current ACTIVE Supply Current (in active mode) STANDBY Supply Current STANDBY Supply Current (in Halt mode) RAM data retention VDDCA regulated voltage !! POR voltage SVLD voltage Conditions +25°C (note2) (note2 / 3 / 4) 0°C...+60°C +25°C (note3 / 4) 0°C...+60°C 0°C...+60°C Symb. IVDDa Min. IVDDa IVDDh IVDDh Vrd VDDCA VPOR VSVLD Typ.(note5) 9.0 2 1.3 1.6 2.25 2.0 0.9 2.5 Max. 15 Unit μA 20 4 μA μA 7 2.6 1.40 2.8 μA V V V V Max. 18 Unit μA VDD=5.0V, T=25°C (unless otherwise specified) Parameter ACTIVE Supply Current ACTIVE Supply Current (in active mode) STANDBY Supply Current STANDBY Supply Current (in Halt mode) Conditions +25°C (note2) (note2 / 3 / 4) 0°C...+60°C +25°C (note3 / 4) 0°C...+60°C Symb. IVDDa IVDDa IVDDh IVDDh Min. Typ.(note5) 13 1.8 20 5 μA μA 10 μA Note2: test loop with successive writing and reading of two different addresses with an inverted values (five instructions should be reserved for this measurement), Note3: NOT tested at temperature if delivered in chip form. Note4: Test conditions for ACTIVE and STANDBY Supply current mode are: Qin = external square wave, from rail to rail of Vreg (regulated voltage) with 100nF capacitor on Vreg. fQin = 33kHz. Note5: For current measurement typical quartz described in Operating Conditions is used. All I/O pins without internal Pull Up/Down are pulled to VDD externally. Copyright © 2005, EM Microelectronic-Marin SA 9 www.emmicroelectronic.com EM65XX Todays Versions EM6504P02 I/O’s VLD levels Remarks As defined As defined - X=3526 Vbat1 X=3282 PC1 X=1842 PC2 X=1238 PC3 X=634 X=27 All dimensions in Microns PC0 X=2446 Die, pad location and size Y=4237 Y=4030 BUZZER Y=3686 PB3 Y=3602 Y=3442 TEST Y=3343 VSS Y=2938 PB2 Y=2841 Y=2681 EM6504 CHIP SIZE is X = 4953 microns by Y = 4445 microns or X = 195 mils by Y = 175 mils heith of the die Z = 11 mils PB1 Y=1792 Y=1632 RESET Y=1311 PB0 Y=1031 Y=871 QOut Y=939 Vss Y=290 Qin Y=163 Y=0 Y=108 X=4764 X=4550 STB/RST X=4068 PA2 X=3156 PA1 X=1487 PA0 X=814 VddCA X=548 X=0 X=−210 Y=−208 PA3 X=3591 Y=0 Package SO24 package. See dimensions in section 10. Copyright © 2005, EM Microelectronic-Marin SA 10 www.emmicroelectronic.com EM65XX 4. EM6505 Input/Output ports All ports if selected as outputs are Push-pull outputs (driving high / low). Inputs are not blocked when Output is selected and Outputs stays active also in Sleep mode. Input/Output Port Options Pull-Up Yes / No Pull-Down Yes / No 0 A0 A1 A2 A3 B0 B1 B2 B3 C0 C1 C2 C3 D0 D1 D2 D3 Nch-open drain Input blocked Yes / No when Output Yes / No 4 5 1 PA0 input PA1 input PA2 input PA3 input PB0 In/Out PB1 In/Out PB2 In/Out PB3 In/Out PC0 In/Out PC1 In/Out PC2 In/Out PC3 In/Out PD0 In/Out PD1 In/Out PD2 In/Out PD3 In/Out NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO Output Hi-Z in SLEEP mode Yes / No 6 NO NO NO NO NO NO NO NO NO NO NO NO PortA reset No PortA RESET is selected. NO PortA reset combination 0 RA PortA RESET PA0 & PA1 logic AND input reset PA0 & PA1 & PA2 logic AND input reset 2 1 PA0 & PA1 & PA2 & PA3 logic AND input reset 3 X Supply Voltage Level Detector T= -10°C to 60°C Symb. VSVLD1 VSVLD2 VSVLD3 Parameter SVLD voltage Level1 SVLD voltage Level2 SVLD voltage Level3 Copyright © 2005, EM Microelectronic-Marin SA Min. 2.02 3.70 4.15 Typ. 2.30 4.00 4.50 11 Max. 2.38 4.30 4.86 Unit V V V www.emmicroelectronic.com EM65XX RC oscillator adjustment on the EM6505 (MFP version only) Register name RC_Adj_Low RC_Adj_High add add hex dec 66 67 102 103 power up value b'3210 write_bits 0001 0: OscAdj[0] 1: OscAdj[1] 2: OscAdj[2] 3: OscAdj[3] 0: OscAdj[4] 1: OscAdj[5] 2: OscAdj[6] 3: OscAdj[7] 1000 read_bits Remarks Read/Write_bits ---- Adjustment of RC oscillator (4 LSB) ---- Adjustment of RC oscillator (4 MSB) On the EM6605 (ROM version), the adjustment of the RC oscillator is done by metal option (refer to chapter 14 of the EM6605 datasheet). On the EM6505 (MFP version), there is no metal option to adjust the frequency range. Adjusting the 8 bits contained in registers “RC_Adj_Low” and “RC_adj_High” sets the frequency. The bit “OscAdj[7]” selects the frequency range: low or high frequency range (refer to chapter 4 of the EM6605 datasheet). The others bits as well as the external resistor on Pin 10, are used to adjust more precisely the frequency. The frequency has to be in the range of 30kHz to 300kHz (refer to chapter 17.7 of the EM6605 datasheet). Electrical specifications Standard Operating Conditions Parameter Temperature VDD VSS Cvreg Value 0°C...+60°C +2.0 ...+5.0V 0 V (reference) min. 100nF Description Rext 50kΩ - 400kΩ external R to set clock frequency regulated voltage capacitor tow. Vss Cvreg : This capacitor maintains the Regulated Supply to the internal logic. DC characteristics - Power Supply Pins For Frequency range of 30 - 300 kHz VDD=5.0V, T=25°C, f=32kHz (note1) (unless otherwise specified) Rext ≈ 330kΩ Parameter Conditions Symb. ACTIVE Supply Current ACTIVE Supply Current (in active mode) STANDBY Supply Current STANDBY Supply Current (in Halt mode) SLEEP Supply Current SLEEP Supply Current (SLEEP =1) Regulated Voltage +25°C (note2) (note2) (note3) 0°C...+60°C +25°C (note3) 0°C...+60°C +25°C (note3) 0°C...+60°C Vreg not at VDD IVDDa Typ. (note1) 30.0 IVDDa IVDDh IVDDh IVDDs Copyright © 2005, EM Microelectronic-Marin SA Min. IVDDs Vreg 1.5 12 Max. Unit 40.0 µA 17.0 50.0 20.0 µA µA 1.0 40.0 2.0 µA µA 2.0 5.0 2.5 µA V www.emmicroelectronic.com EM65XX VDD=5.0V, T=25°C, f=200kHz (note1) (unless otherwise specified) Rext ≈ 62kΩ Parameter Conditions Symb. Min. ACTIVE Supply Current ACTIVE Supply Current (in active mode) STANDBY Supply Current STANDBY Supply Current (in Halt mode) SLEEP Supply Current SLEEP Supply Current (SLEEP =1) +25°C (note2) (note2) (note3) 0°C...+60°C +25°C (note3) 0°C...+60°C +25°C (note3) 0°C...+60°C IVDDa Typ. (note1) 80.0 IVDDa IVDDh IVDDh IVDDs IVDDs Max. Unit 100.0 µA 30.0 120.0 40.0 µA µA 1.0 50.0 2.0 µA µA 5.0 µA Note1: For current measurement the corresponding resistor for targeted frequency ±20% is selected; Rext : external resistor between the RCin and Vss pins. All I/O pins without internal Pull Up/Down are pulled to VDD externally. Note2: Test loop with successive writing and reading of two different addresses with an inverted values (five instructions should be reserved for this measurement), Note3: NOT tested at temperature if delivered in chip form. Copyright © 2005, EM Microelectronic-Marin SA 13 www.emmicroelectronic.com EM65XX Today’s Versions EM6505P02 I/O’s VLD levels Remarks As defined As defined - PC3 X=3828 PC2 X=4082 PD1 X=1648 PD3 X=405 PD2 X=1026 All dimensions in Microns PD0 X=2369 Die, pad location and size Y=4211 Y=4005 PC1 Y=3708 RESET Y=3439 PC0 Y=2637 STB/RST Y=2383 VSS Y=2109 RCout Y=1890 VddCA Y=2723 Vbat Y=2469 EM6505 CHIP SIZE is X = 5003 microns by Y = 4419 microns or X = 197 mils by Y = 174 mils heith of the die Z = 11 mils RCin Y=1253 X=4589 PA0 Y=1473 PA1 Y=1209 PA2 Y=945 X=4795 TEST X=4545 PB3 X=3432 PB2 X=2901 PB1 X=2370 PA3 X=522 X=0 X=−208 PB0 X=1839 Y=0 Y=−208 Package SO24 package. See dimensions in section 10. Copyright © 2005, EM Microelectronic-Marin SA 14 www.emmicroelectronic.com EM65XX 5. EM6517 A new complete specification exists on the EM6517. Please refer to this document on our web site. (http://www.emmarin.com/) For more information or questions please contact EM headquarters or your local EM office. Copyright © 2005, EM Microelectronic-Marin SA 15 www.emmicroelectronic.com EM65XX 6. EM6520 A new complete specification exists on the EM6520. Please refer to this document on our web site. (http://www.emmarin.com/) For more information or questions please contact EM headquarters or your local EM office. Copyright © 2005, EM Microelectronic-Marin SA 16 www.emmicroelectronic.com EM65XX 7. EM6521 A new complete specification exists on the EM6521. Please refer to this document on our web site. (http://www.emmarin.com/) For more information or questions please contact EM headquarters or your local EM office. Copyright © 2005, EM Microelectronic-Marin SA 17 www.emmicroelectronic.com EM65XX 8. EM6522 A new complete specification exists on the EM6522. Please refer to this document on our web site. (http://www.emmarin.com/) For more information or questions please contact EM headquarters or your local EM office. Copyright © 2005, EM Microelectronic-Marin SA 18 www.emmicroelectronic.com EM65XX 9. EM6540 Standard Operating Conditions Parameter Temperature VDD VSS CVreg (note 1) fq MIN 0 2.2 2.5 0.22 TYP 25 3.6 3.6 0 1 600 MAX 60 5.5 5.5 Unit °C V V V μF kHz Description fq max 620 kHz fq max 680 kHz Reference terminal regulated voltage capacitor nominal frequency DC characteristics - Power Supply Pins VDD=3V, T=25°C (unless otherwise specified) Parameter Conditions Symb. ACTIVE Supply Current 25°C IVDDa ACTIVE Supply Current (in active mode) STANDBY Supply Current (in Halt mode) SLEEP Supply Current (SLEEP =1) POR voltage (note2) (note3) 0°C...+60°C (note3) 0°C...+60°C (note3) 0°C...+60°C Min. Typ. (note1) 210 Max. 210 250 10 15 0.4 1 μA μA IVDDa μA IVDDh IVDDs VPOR RAM data retention Vrd Regulated Voltage Vreg Unit 1.5 1.5 μA V V 1.85 V Note1: Measured at typical freq. of 600kHz, no load. Note2: Test loop with successive writing and reading of two different addresses with an inverted values (five instructions should be reserved for this measurement), Note3: NOT tested at temperature if delivered in chip form. Metal Options Functionally the EM6640 and the EM6540 are the same except the metal options of the EM6540 which are set in their default state. Copyright © 2005, EM Microelectronic-Marin SA 19 www.emmicroelectronic.com EM65XX Input/Output Port Options A0 A1 A2 A3 B0 B1 B2 B3 C0 C1 C2 C3 PA0 input PA1 input PA2 input PA3 input PB0 In/Out PB1 In/Out PB2 In/Out PB3 In/Out PC0 In/Out PC1 In/Out PC2 In/Out PC3 In/Out Pull-Up controlled by software 0 none none none none 100kΩ 100kΩ 100kΩ 100kΩ 100kΩ 100kΩ 100kΩ 100kΩ Pull-Down controlled by software 1 100kΩ 100kΩ 100kΩ 100kΩ 100kΩ 100kΩ 100kΩ 100kΩ 100kΩ 100kΩ 100kΩ 100kΩ Digital WatchDog YES level of SWB data VDD Digital Watchdog Option MDigWD SWBdataLevel Option MSWBdataLevel Supply Voltage Level Detector T= -10°C to 60°C Symb. VSVLD1 VSVLD2 Parameter SVLD voltage Level1 SVLD voltage Level2 Min. 2.02 2.30 Typ. 2.20 2.50 Max. 2.37 2.70 Unit V V Today’s Versions EM6540P04 I/O’s VLD levels Remarks As defined As defined - Copyright © 2005, EM Microelectronic-Marin SA 20 www.emmicroelectronic.com EM65XX Die, pad location and size Package SO18 package. See dimensions in section 10. Copyright © 2005, EM Microelectronic-Marin SA 21 www.emmicroelectronic.com EM65XX Pin out for the EM6540 (MFP of the EM6640) Package: SO18 VReg 1 18 PSCK Test 2 17 PSDIO PA0 3 16 VSS PA1 4 15 VBat PA2 5 14 PC3 PA3 6 13 PC2 PB0 7 12 PC1 PB1 8 11 PC0 PB2 9 10 PB3 E M 6 5 4 0 MFP programming connection for field programming QOut QIn VSS VBat 18 17 16 15 14 13 12 MFP programer 11 10 8 9 EM6540 1 2 3 4 5 6 7 Test VReg Copyright © 2005, EM Microelectronic-Marin SA MFP programer 22 www.emmicroelectronic.com EM65XX 10. Package Dimensions All MFPs are available in chip form on special request. Figure 1. SOP 18 Pin Package SOP-18(1.27mm pitch, 300mils body width) Figure 2. SOP 24 Pin Package SOP-24(1.27mm pitch, 300mils body width) Copyright © 2005, EM Microelectronic-Marin SA 23 www.emmicroelectronic.com EM65XX Figure 3. SOP 28 Pin Package SOP-28(1.27mm pitch, 300mils body width) Copyright © 2005, EM Microelectronic-Marin SA 24 www.emmicroelectronic.com EM65XX Figure 4. TQF 44 Pin Package TOP VIEW D ODD LEAD SIDES EVEN LEAD SIDES e b D1 DETAIL "A" e SEE DETAIL "A" S Y M B O L A TQFP44 ALL DIMENSIONS IN MILLIMETERS MIN. TYP. SEE DETAIL "B" MAX. 1.20 A A1 0.05 A2 0.95 0.15 1.00 D 12.00 BSC. D1 10.00 BSC. 1.05 DETAIL "B" 0° MIN. L 0.08/0.20 R. A2 0.08 R. MIN. 0.20 MIN. 0.60 0.75 44 0.80 BSC e b A1 0.45 N 0.30 0.37 0.45 0-7° L 1.00 REF. Copyright © 2005, EM Microelectronic-Marin SA 1.00/0.10 MM FORM, 1.00 MM THICK PACKAGE OUTLINE, TQFP, 10X10 MM BODY, 25 www.emmicroelectronic.com EM65XX Figure 5. TQF 52 Pin Package TOP VIEW D ODD LEAD SIDES EVEN LEAD SIDES e b D1 DETAIL "A" e SEE DETAIL "A" S Y M B O L A TQFP52 ALL DIMENSIONS IN MILLIMETERS MIN. TYP. 1.20 A SEE DETAIL "B" MAX. A1 0.05 A2 0.95 0.15 1.00 D 12.00 BSC. D1 10.00 BSC. 1.05 DETAIL "B" 0° MIN. L 0.08/0.20 R. A2 0.08 R. MIN. 0.20 MIN. 0.60 0.75 52 0.65 BSC e b A1 0.45 N 0.22 0.32 0.38 0-7° L 1.00 REF. Copyright © 2005, EM Microelectronic-Marin SA 1.00/0.10 MM FORM, 1.00 MM THICK PACKAGE OUTLINE, TQFP, 10X10 MM BODY, 26 www.emmicroelectronic.com EM65XX Figure 6. TQF 64 Pin Package TOP VIEW D ODD LEAD SIDES EVEN LEAD SIDES e b D1 DETAIL "A" e SEE DETAIL "A" S Y M B O L A TQFP64 ALL DIMENSIONS IN MILLIMETERS MIN. TYP. 1.20 A SEE DETAIL "B" MAX. A1 0.05 A2 0.95 0.15 1.00 D 12.00 BSC. D1 10.00 BSC. 1.05 DETAIL "B" 0° MIN. L 0.08/0.20 R. A2 0.08 R. MIN. 0.20 MIN. 0.60 0.75 64 0.50 BSC e b A1 0.45 N 0.17 0.22 0.23 0-7° L 1.00 REF. 1.00/0.10 MM FORM, 1.00 MM THICK PACKAGE OUTLINE, TQFP, 10X10 MM BODY, For more information or questions please contact EM headquarters or your local EM office. Copyright © 2005, EM Microelectronic-Marin SA 27 www.emmicroelectronic.com EM65XX 11. Ordering Information Ordering Part Number Part Number Package/Die Form EM6503%%%SO24A EM6503%%%WP11 EM6504%%%SO24A EM6504%%%WP11 EM6505%%%SO24A EM6505%%%WP11 EM6517%%%SO28A EM6517%%%WP11 EM6520%%%TQ44D EM6520%%%WP11 EM6521%%%TQ52D EM6521%%%WP11 EM6522%%%TQ64D EM6522%%%WP11 EM6540%%%SO18A EM6540%%%WP11 24 pin SOIC Die in waffle pack 24 pin SOIC Die in waffle pack 24 pin SOIC Die in waffle pack 28 pin SOIC Die in waffle pack TQFP 44 pin Die in waffle pack TQFP 52 pin Die in waffle pack TQFP 64 pin Die in waffle pack 18 pin SOIC Die in waffle pack Delivery Form/ Thickness Stick 11 mils Stick 11 mils Stick 11 mils Stick 11 mils Trays (Plate) 11 mils Trays (Plate) 11 mils Trays (Plate) 11 mils Stick 11 mils Please make sure to give the complete Part Number when ordering, including the 3-digit version. The version is made of 3 digits %%%: the first one is a letter and the last two are numbers, e.g. P04 , P07, P12, etc. For other delivery forms, please contact EM Microelectronic-Marin S.A. EM Microelectronic-Marin SA (EM) makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in EM's General Terms of Sale located on the Company's web site. EM assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of EM are granted in connection with the sale of EM products, expressly or by implications. EM's products are not authorized for use as components in life support devices or systems. © EM Microelectronic-Marin SA, 10/05, Rev. I Copyright © 2005, EM Microelectronic-Marin SA 28 www.emmicroelectronic.com