E-OEC FM-9056LM-5AN

FM-9038LM-5AN
IR Receiver Modules for Remote Control Systems
Description
The FM-9038LM-5AN is remote control receiver modules.
Pin diode and receiver IC are assembled on one module.
Small-sized, light-weight, and low current consumption.
modules have been achieved by using resin mold.
The demodulated output signal can directly be decoded
by a microprocessor. The main benefit is the reliable
function even in disturbed ambient and the protection
against uncontrolled output pulses.
Features
ƒ Supply Voltage Range: 2.7V to 6.5V
ƒ TTL and CMOS compatibility
ƒ Photo detector and preamplifier in one package.
ƒ Internal filter for PCM frequency
ƒ Open collector output (built-in Pull-up resistor(40K)
ƒ Output active low
ƒ Enhanced Immunity against all kinds of disturbance light
ƒ No occurrence of disturbance pulses at output pin within nominal conditions.
ƒ Short settling time after power On.( below 1msec)
ƒ Meet RoHS
Application Circuit
VCC
47~100Ω
IR Receiver Module
IC
Transmitter
VCC
47uf
MCU
VOUT
GND
GND
R-C filter recommended to suppress power supply disturbances.
R-C filter should be connected closely between VCC pin and GND pin.
Block Diagram
Ordering Info.(carrier frequencies)
Type
Carrier Frequency (fo)
FM-9032LM-5AN
32.7 K
FM-9036LM-5AN
36.7 K
FM-9038LM-5AN
37.9 K
FM-9040LM-5AN
40.0 K
FM-9056LM-5AN
56.7 K
光電企業有限公司
November 2006 Rev 1.3
FM-9038LM-5AN
Absolute Maximum Ratings
(Ta = 25℃)
Symbol
Ratings
Unit
Supply Voltage
VCC
7.0
V
Output Voltage
VOUT
0.2 ~Vcc
V
Output Current
IOUT
2.5
mA
Operating Temperature
Topr
-20 ~ +80
℃
Storage Temperature
Tstg
-30 ~ +85
℃
Soldering Temperature
Tsd
260℃, Max 5 sec
℃
Parameter
Electro-optical Characteristics
(Ta = 25℃)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Supply Voltage
Vcc
2.7
5.0
6.5
V
Supply Current
ICC
0.8
1.0
1.3
mA
No input signal
Max input current
IIN
0.5
1.0
1.5
mA
Vin=0
Voh
Vcc-0.5
-
-
V
Vol
-
0.2
0.4
V
λp
-
940
-
nm
±0˚
-
15
-
m
±30˚
-
10
-
m
±45˚
-
7
-
m
Output Voltage
Peak Wave Length
Arrival Distance
L
Max. Voltage Gain
Av
70
76
82
dB
Internal Pull-up Resistor
Rpul
36
40
44
㏀
BPF Bandwidth
fbw
-
3.5
-
kHz
BPF frequency
fc
-3.5
fo
+3.5
%
Output Pulse width
Tpw
450
600
750
㎲
光電企業有限公司
Vcc=5V
Fig.
1,2,3
fin=37.9kHz
Vin=30㎶pp
fin=37.9kHz
Vin=30㎶pp
Fig.
1,2,6
November 2006 Rev 1.3
FM-9038LM-5AN
[ Fig.1 ] Data Signal diagram
t Pause
Data Word
enlarge
t Burst
Carrier Frequency : fo
t Gap
(Output pulse)
ƒ t Gap : Signal gap time between two burst in pulses of carrier. Minimum Gap Time ≧ 300us
ƒ t Burst : Length of a burst in pulses of the carrier frequency. Minimum Burst ≧ 300us
ƒ t pause : Data pause between two data words. Minimum Data PauseTime ≧ 20ms
[ Fig.2 ] Transmitter
10K
PD
S/Transmitter
VCC
100uf
VOUT
10K
GND
30㎝
※ The specifications shall be satisfied under the following conditions. The standard transmitter
shall be specified of the burst wave form adjusted to VOUT 200mVp-p upon Po measuring
circuit Standard Transmitter
[ Fig.3 ] Test condition of arrival distance
Vout
osc
Transmitter
GND
Vcc
: Indicates horizontal and
vertical directions
[ Measurement condition for arrival distance ]
☞ Ambient light source : Detecting surface illumination shall be irradiate 200±50Lux
under ordinary white fluorescence lamp without high frequency lighting
光電企業有限公司
November 2006 Rev 1.3
FM-9038LM-5AN
Electrical/Optical Characteristics
[ Fig.5 ] Sensitivity vs. Supply Voltage
2.5
100
2.0
80
Relative Sensitivity(%)
Supply Current(㎃)
[ Fig.4 ] Supply Current vs. Voltage
1.5
1.0
0.5
60
40
20
0
0.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
2.5
6.5
3.0
3.5
[ Fig.6 ] Output Pulse Width vs. Distance
4.5
5.0
5.5
6.0
6.5
[ Fig.7 ] Directivity (Horizontal/Vertical)
0˚
900
Output Pulse Width(㎲)
4.0
Supply Voltage(V)
Supply Voltage(V)
20˚
40˚
Relative Radiant(˚)
800
700
600
500
100
60˚
V
90
H
400
300
0
4
8
12
16
20
24
80
28
Transmission Distance(m)
60
80˚
40 20 0
Relative Sensitivity(%)
ESD Test Results
[ Fig.8 ] BPF Fc Curve
BPF fc
1.2
Parameter
Conditions
Specification
Results
Machine
Model
C=200㎊
R=0Ω
Min ±200V
>±200V
Human
Body
Model
C=100pf
R=1.5KΩ
Min ±2000V
>±2000V
Relative responsiv ity
1
0.8
0.6
0.4
0.2
0
0.5
0.6 0.7
0.8 0.9
1 1.1 1.2 1.3
f/fo Relative Frequency
1.4 1.5
光電企業有限公司
November 2006 Rev 1.3
FM-9038LM-5AN
光電企業有限公司
November 2006 Rev 1.3
FM-9038LM-5AN
◆ Recommended Soldering Condition
Flow Soldering Condition
2. Recommendation Flow Soldering condition Temp & Time
光電企業有限公司
November 2006 Rev 1.3
FM-9038LM-5AN
1. Packing unit for Remote control module
Package
Device
Transfer mold
Type
Packing
Method
Units /
Tube
Poly Bag
200
Poly Bag/
Inner Box
Partial
Max Devices / Max Inner Box /
Shipment of
Inner Box
Outer Box
Outer Box
5
1000
10
* Inner Box # 1 * Inner Box # 1 * Outer Box # 2 * Outer Box # 3
(unit : mm)
Inner Box #1 with Opto-Sensor Logo (170*240*65)
Outer Box #2 with Opto-Sensor Logo (365*360*270)
Outer Box #3 with Opto-Sensor Logo (385*750*300)
2. Packing method
1) Input max 200 units to one Poly bag and label should be attached middle of it.
Antistatic Vinyl
2) Input 5 poly bags to one inner box and label should be attached as below.
Label #1
<Inner Box # 1>
3) Input 10 inner boxes to outer box.
<Outer Box # 2>
4) Input 2 outer boxes into Box #3.
<Outer Box # 3>
光電企業有限公司
November 2006 Rev 1.3