FUJITSU MB95160M

FUJITSU SEMICONDUCTOR
DATA SHEET
DS07-12609-3E
8-bit Microcontroller
CMOS
F2MC-8FX MB95160M Series
MB95F168M/F168N/F168J/FV100D-103
■ DESCRIPTION
The MB95160M series is general-purpose, single-chip microcontrollers. In addition to a compact instruction set,
the microcontrollers contain a variety of peripheral functions.
Note : F2MC is the abbreviation of FUJITSU Flexible Microcontroller.
■ FEATURE
• F2MC-8FX CPU core
Instruction set optimized for controllers
• Multiplication and division instructions
• 16-bit arithmetic operations
• Bit test branch instruction
• Bit manipulation instructions etc.
• Clock
• Main clock
• Main PLL clock
• Sub clock
• Sub PLL clock
(Continued)
Be sure to refer to the “Check Sheet” for the latest cautions on development.
“Check Sheet” is seen at the following support page
URL : http://www.fujitsu.com/global/services/microelectronics/product/micom/support/index.html
“Check Sheet” lists the minimal requirement items to be checked to prevent problems beforehand in system
development.
Copyright©2007 FUJITSU LIMITED All rights reserved
MB95160M Series
(Continued)
• Timer
• 8/16-bit compound timer × 2 channels
Can be used to interval timer, PWC timer, PWM timer and input capture.
• 8/16-bit PPG × 2 channels
• 16-bit PPG × 1 channel
• Time-base timer × 1 channel
• Watch prescaler × 1 channel
• LIN-UART × 1 channel
• LIN function, clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
• Full duplex double buffer
• UART/SIO × 1 channel
• Clock asynchronous (UART) or clock synchronous (SIO) serial data transfer capable
• Full duplex double buffer
• I2C* × 1 channel
Built-in wake-up function
• External interrupt × 8 channels
• Interrupt by edge detection (rising, falling, or both edges can be selected)
• Can be used to recover from low-power consumption (standby) modes.
• 8/10-bit A/D converter × 8 channels
8-bit or 10-bit resolution can be selected.
• LCD controller (LCDC)
• 32 SEG × 4 COM (Max 128 pixels)
• With blinking function
• Low-power consumption (standby) mode
• Stop mode
• Sleep mode
• Watch mode
• Time-base timer mode
• I/O port
• The number of maximum ports : Max 53
• Port configuration
- General-purpose I/O ports (N-ch open drain) : 2 ports
- General-purpose I/O ports (CMOS)
: 51 ports
• Programmable input voltage levels of port
Automotive input level / CMOS input level / hysteresis input level
• Flash memory security function
Protects the content of Flash memory
* : Purchase of Fujitsu I2C components conveys a license under the Philips I2C Patent Rights to use, these
components in an I2C system provided that the system conforms to the I2C Standard Specification as defined
by Philips.
2
MB95160M Series
■ PRODUCT LINEUP
Part number*1
Parameter
MB95F168M
MB95F168N
Type
Flash memory product
ROM capacity
60 Kbytes
RAM capacity
2 Kbytes
Option*2
Reset output
Clock supervisor
CPU functions
Peripheral functions
Yes
Clock system
Low voltage
detection reset
MB95F168J
No
Dual clock
No
Yes
No
Yes
Number of basic instructions
: 136
Instruction bit length
: 8 bits
Instruction length
: 1 to 3 bytes
Data bit length
: 1, 8, and 16 bits
Minimum instruction execution time : 61.5 ns (at machine clock frequency 16.25
MHz)
Interrupt processing time
: 0.6 µs (at machine clock frequency 16.25 MHz)
Ports (Max 53 ports)
General-purpose I/O port (N-ch open drain) : 2 ports
General-purpose I/O port (CMOS)
: 51 ports
Programmable input voltage levels of port :
Automotive input level / CMOS input level / hysteresis input level
Time-base timer
(1 channel)
Interrupt cycle : 0.5 ms, 2.1 ms, 8.2 ms, 32.8 ms (at main oscillation clock 4 MHz)
Watchdog timer
Reset generated cycle
At main oscillation clock 10 MHz
: Min 105 ms
At sub oscillation clock 32.768 kHz (for dual clock product) : Min 250 ms
Wild register
Capable of replacing 3 bytes of ROM data
I2C
(1 channel)
Master/slave sending and receiving
Bus error function and arbitration function
Detecting transmitting direction function
Start condition repeated generation and detection functions
Built-in wake-up function
UART/SIO
(1 channel)
Data transfer capable in UART/SIO
Full duplex double buffer,
variable data length (5/6/7/8-bit), built-in baud rate generator
NRZ type transfer format, error detected function
LSB-first or MSB-first can be selected.
Clock synchronous (SIO) or clock asynchronous (UART) serial data transfer capable
LIN-UART
(1 channel)
Dedicated reload timer allowing a wide range of communication speeds to be set.
Full duplex double buffer.
Capable of serial data transfer synchronous or asynchronous to clock signal.
LIN functions available as the LIN master or LIN slave.
8/10-bit A/D converter
8-bit or 10-bit resolution can be selected.
(8 channels)
(Continued)
3
MB95160M Series
Peripheral functions
(Continued)
Part number*1
Parameter
MB95F168M
MB95F168N
MB95F168J
LCD controller
(LCDC)
COM output
: 4 (Max)
SEG output
: 32 (Max)
LCD drive power supply (bias) pin
:4
32 SEG × 4 COM : 128 pixels can be displayed.
Duty LCD mode
Operable in LCD standby mode
With blinking function
Built-in division resistance for LCD drive
8/16-bit compound
timer (2 channels)
Each channel of the timer can be used as “8-bit timer × 2 channels” or “16-bit timer ×
1 channel”.
Built-in timer function, PWC function, PWM function, capture function, and square
wave form output
Count clock : 7 internal clocks and external clock can be selected.
16-bit PPG
(1 channel)
PWM mode or one-shot mode can be selected.
Counter operating clock : Eight selectable clock sources
Support for external trigger start
8/16-bit PPG
(2 channels)
Each channel of the PPG can be used as “8-bit PPG × 2 channels” or “16-bit PPG × 1
channel”.
Counter operating clock : Eight selectable clock sources
Watch counter
Count clock : Four selectable clock sources (125 ms, 250 ms, 500 ms, or 1 s)
Counter value can be set from 0 to 63. (Capable of counting for 1 minute when
selecting clock source 1 second and setting counter value to 60)
Watch prescaler
(1 channel)
4 selectable interval times (125 ms, 250 ms, 500 ms, or 1 s)
External interrupt
(8 channels)
Interrupt by edge detection (rising, falling, or both edges can be selected.)
Can be used to recover from standby modes.
Flash memory
Supports automatic programming, Embedded Algorithm
Write/Erase/Erase-Suspend/Resume commands
A flag indicating completion of the algorithm
Number of write/erase cycles (Minimum) : 10000 times
Data retention time: 20 years
Erase can be performed on each block
Block protection with external programming voltage
Flash Security Feature for protecting the content of the Flash
Standby mode
Sleep, stop, watch, and time-base timer
*1 : MASK ROM products are currently under consideration.
*2 : For details of option, refer to “■ MASK OPTION”.
Note : Part number of evaluation product in MB95160M series is MB95FV100D-103. When using it, the MCU board
(MB2146-303A) is required.
4
MB95160M Series
■ OSCILLATION STABILIZATION WAIT TIME
The initial value of the main clock oscillation stabilization wait time is fixed to the maximum value. The maximum
value is shown as follows.
Oscillation stabilization wait time
Remarks
(214-2) /FCH
Approx. 4.10 ms (at main oscillation clock 4 MHz)
■ PACKAGES AND CORRESPONDING PRODUCTS
Part number
Package
MB95F168M/F168N/F168J
MB95FV100D-103
FPT-64P-M23
FPT-64P-M24
BGA-224P-M08
: Available
: Unavailable
5
MB95160M Series
■ DIFFERENCES AMONG PRODUCTS AND NOTES ON SELECTING PRODUCTS
• Notes on Using Evaluation Products
The evaluation product has not only the functions of the MB95160M series but also those of other products to
support software development for multiple series and models of the F2MC-8FX family. The I/O addresses for
peripheral resources not used by the MB95160M series are therefore access-barred. Read/write access to these
access-barred addresses may cause peripheral resources supposed to be unused to operate, resulting in
unexpected malfunctions of hardware or software.
Particularly, do not use word access to odd numbered byte address in the prohibited areas (If these access are
used, the address may be read or written unexpectedly).
Also, as the read values of prohibited addresses on the evaluation product are different to the values on the
Flash memory products, do not use these values in the program.
The functions corresponding to certain bits in single-byte registers may not be supported on some Flash memory
products. However, reading or writing to these bits will not cause malfunction of the hardware. Also, as the
evaluation and Flash memory products are designed to have identical software operation, no particular precautions are required.
• Difference of Memory Spaces
If the amount of memory on the evaluation product is different from that of the Flash memory products, carefully
check the difference in the amount of memory from the model to be actually used when developing software.
For details of memory space, refer to “■ CPU CORE”.
• Current Consumption
For details of current consumption, refer to “■ ELECTRICAL CHARACTERISTICS”.
• Package
For details of information on each package, refer to “■ PACKAGES AND CORRESPONDING PRODUCTS” and
“■ PACKAGE DIMENSIONS”.
• Operating voltage
The operating voltage is different among the evaluation and Flash memory products.
For details of operating voltage, refer to “■ ELECTRICAL CHARACTERISTICS”
6
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
AVR
P14/PPG0
P13/TRG0/ADTG
P12/UCK0
P11/UO0
P10/UI0
P24/EC0/SDA0
P23/TO01/SCL0
P22/TO00
P21/PPG01
P20/PPG00
MOD
X0
X1
VSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
C
X1A
X0A
RST
P90/V3
P91/V2
P92/V1
P93/V0
P94
P95
PA0/COM0
PA1/COM1
PA2/COM2
PA3/COM3
PB0/SEG00
AVCC
VCC
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
AVSS
P00/INT00/AN00/SEG31
P01/INT01/AN01/SEG30
P02/INT02/AN02/SEG29
P03/INT03/AN03/SEG28
P04/INT04/AN04/SEG27
P05/INT05/AN05/SEG26
P06/INT06/AN06/SEG25
P07/INT07/AN07/SEG24
P67/SEG23/SIN
P66/SEG22/SOT
P65/SEG21/SCK
P64/SEG20/EC1
P63/SEG19/TO11
P62/SEG18/TO10
P61/SEG17/PPG11
MB95160M Series
■ PIN ASSIGNMENT
(TOP VIEW)
LQFP-64
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
P60/SEG16/PPG10
PC7/SEG15
PC6/SEG14
PC5/SEG13
PC4/SEG12
PC3/SEG11
PC2/SEG10
PC1/SEG09
PC0/SEG08
PB7/SEG07
PB6/SEG06
PB5/SEG05
PB4/SEG04
PB3/SEG03
PB2/SEG02
PB1/SEG01
(FPT-64P-M23,FPT-64P-M24)
7
MB95160M Series
■ PIN DESCRIPTION
Pin no.
Pin name
I/O circuit
type*
1
AVCC
⎯
A/D converter power supply pin
2
AVR
⎯
A/D converter reference input pin
3
P14/PPG0
General-purpose I/O port.
The pin is shared with 16-bit PPG ch.0 output.
4
P13/TRG0/
ADTG
General-purpose I/O port.
The pin is shared with 16-bit PPG ch.0 trigger input (TRG0) and
A/D converter trigger input (ADTG) .
5
P12/UCK0
6
P11/UO0
7
P10/UI0
8
P24/EC0/
SDA0
H
Function
General-purpose I/O port.
The pin is shared with UART/SIO ch.0 clock I/O.
General-purpose I/O port.
The pin is shared with UART/SIO ch.0 data output.
G
I
General-purpose I/O port.
The pin is shared with UART/SIO ch.0 data input.
General-purpose I/O port.
The pin is shared with 8/16-bit compound timer ch.0 clock input
(EC0) and I2C ch.0 data I/O (SDA0) .
9
P23/TO01/
SCL0
General-purpose I/O port.
The pin is shared with 8/16-bit compound timer ch.0 output (TO01)
and I2C ch.0 clock I/O (SCL0) .
10
P22/TO00
General-purpose I/O port.
The pin is shared with 8/16-bit compound timer ch.0 output.
11
P21/PPG01
12
P20/PPG00
13
MOD
14
X0
15
X1
16
H
General-purpose I/O port.
The pin is shared with 8/16-bit PPG ch.0 output.
General-purpose I/O port.
The pin is shared with 8/16-bit PPG ch.0 output.
B
Operating mode designation pin
A
Main clock oscillation pin
VSS
⎯
Power supply pin (GND)
17
VCC
⎯
Power supply pin
18
C
⎯
Capacitor connection pin
19
X1A
20
X0A
A
Sub clock oscillation pins (32 kHz)
21
RST
B’
Reset pin
22
P90/V3
23
P91/V2
24
P92/V1
R
General-purpose I/O port.
The pins are shared with power supply pin for LCDC drive.
25
P93/V0
(Continued)
8
MB95160M Series
Pin no.
Pin name
26
P94
27
P95
28
PA0/COM0
29
PA1/COM1
30
PA2/COM2
31
PA3/COM3
32
PB0/SEG00
33
PB1/SEG01
34
PB2/SEG02
35
PB3/SEG03
36
PB4/SEG04
37
PB5/SEG05
38
PB6/SEG06
39
PB7/SEG07
40
PC0/SEG08
41
PC1/SEG09
42
PC2/SEG10
43
PC3/SEG11
44
PC4/SEG12
45
PC5/SEG13
46
PC6/SEG14
47
PC7/SEG15
48
P60/SEG16/
PPG10
49
P61/SEG17/
PPG11
50
P62/SEG18/
TO10
I/O circuit
type*
Function
S
General-purpose I/O port.
M
General-purpose I/O port.
The pins are shared with LCDC COM output (COM0 to COM3).
M
General-purpose I/O port.
The pins are shared with LCDC SEG output (SEG00 to SEG07).
M
General-purpose I/O port.
The pins are shared with LCDC SEG output (SEG08 to SEG15).
M
General-purpose I/O port.
The pins are shared with LCDC SEG output (SEG16, SEG17) and
8/16-bit PPG ch.1 output (PPG10, PPG11) .
General-purpose I/O port.
The pin is shared with LCDC SEG output (SEG18) and 8/16-bit
compound timer ch.1 output (TO10) .
(Continued)
9
MB95160M Series
(Continued)
I/O circuit
type*
Function
Pin no.
Pin name
51
P63/SEG19/
TO11
General-purpose I/O port.
The pin is shared with LCDC SEG output (SEG19) and 8/16-bit
compound timer ch.1 output (TO11) .
52
P64/SEG20/
EC1
General-purpose I/O port.
The pin is shared with LCDC SEG output (SEG20) and 8/16-bit
compound timer ch.1 clock input (EC1) .
M
53
P65/SEG21/
SCK
General-purpose I/O port.
The pin is shared with LCDC SEG output (SEG21) and LIN-UART
clock I/O (SCK) .
54
P66/SEG22/
SOT
General-purpose I/O port.
The pin is shared with LCDC SEG output (SEG22) and LIN-UART
data output (SOT) .
55
P67/SEG23/
SIN
56
P07/INT07/
AN07/SEG24
57
P06/INT06/
AN06/SEG25
58
P05/INT05/
AN05/SEG26
59
P04/INT04/
AN04/SEG27
60
P03/INT03/
AN03/SEG28
61
P02/INT02/
AN02/SEG29
62
P01/INT01/
AN01/SEG30
63
P00/INT00/
AN00/SEG31
64
AVSS
N
General-purpose I/O port.
The pin is shared with LCDC SEG output (SEG23) and LIN-UART
data input (SIN) .
F
General-purpose I/O port.
The pins are shared with external interrupt input (INT00 to INT07) ,
A/D analog input (AN00 to AN07) and LCDC SEG output (SEG24 to
SEG31) .
⎯
Power supply pin (GND) of A/D converter
* : Refer to “■ I/O CIRCUIT TYPE” for details on the I/O circuit types.
10
MB95160M Series
■ I/O CIRCUIT TYPE
Type
Circuit
Remarks
A
X1 (X1A)
Clock input
X0 (X0A)
N-ch
• Oscillation circuit
• High-speed side
Feedback resistance : approx. 1 MΩ
• Low-speed side
Feedback resistance : approx. 10 MΩ
Standby control
B
Mode input
B’
Reset input
N-ch
• Only for input
• Hysteresis input
• Hysteresis input
• Reset output
Reset output
F
P-ch
Digital output
Digital output
N-ch
•
•
•
•
•
CMOS output
LCD output
Hysteresis input
Analog input
Automotive input
•
•
•
•
•
CMOS output
CMOS input
Hysteresis input
With pull-up control
Automotive input
Analog input
LCD output
Hysteresis input
A/D control
LCD control
Standby control
External interrupt
control
Automotive input
G
R
P-ch
Pull-up control
P-ch
N-ch
Digital output
Digital output
CMOS input
Hysteresis input
Standby control
Automotive input
(Continued)
11
MB95160M Series
Type
Circuit
Remarks
H
Pull-up control
R
P-ch
P-ch
Digital output
•
•
•
•
CMOS output
Hysteresis input
With pull-up control
Automotive input
•
•
•
•
N-ch open drain output
CMOS input
Hysteresis input
Automotive input
•
•
•
•
CMOS output
LCD output
Hysteresis input
Automotive input
•
•
•
•
•
CMOS output
LCD output
CMOS input
Hysteresis input
Automotive input
Digital output
N-ch
Hysteresis input
Automotive input
Standby control
I
Digital output
N-ch
CMOS input
Hysteresis input
Automotive input
Standby control
M
P-ch
Digital output
Digital output
N-ch
LCD output
Hysteresis input
Automotive input
LCD control
Standby control
N
P-ch
Digital output
Digital output
N-ch
LCD output
CMOS input
LCD control
Standby control
Hysteresis input
Automotive input
(Continued)
12
MB95160M Series
(Continued)
Type
Circuit
Remarks
R
P-ch
Digital output
Digital output
N-ch
•
•
•
•
CMOS output
LCD power supply
Hysteresis input
Automotive input
•
•
•
•
CMOS output
LCD power supply
Hysteresis input
Automotive input
LCD built-in internal split
resistor I/O
Hysteresis input
Automotive input
Standby control
LCD control
S
P-ch
Digital output
Digital output
N-ch
Standby control
Hysteresis input
Automotive input
13
MB95160M Series
■ HANDLING DEVICES
• Preventing Latch-up
Care must be taken to ensure that maximum voltage ratings are not exceeded when they are used.
Latch-up may occur on CMOS ICs if voltage higher than VCC or lower than VSS is applied to input and output pins
other than medium- and high-withstand voltage pins or if higher than the rating voltage is applied between VCC
pin and VSS pin.
When latch-up occurs, power supply current increases rapidly and might thermally damage elements.
• Stable Supply Voltage
Supply voltage should be stabilized.
A sudden change in power-supply voltage may cause a malfunction even within the guaranteed operating range
of the Vcc power-supply voltage.
For stabilization, in principle, keep the variation in Vcc ripple (p-p value) in a commercial frequency range
(50/60 Hz) not to exceed 10% of the standard Vcc value and suppress the voltage variation so that the transient
variation rate does not exceed 0.1 V/ms during a momentary change such as when the power supply is switched.
• Precautions for Use of External Clock
Even when an external clock is used, oscillation stabilization wait time is required for power-on reset, wake-up
from sub clock mode or stop mode.
PIN CONNECTION
• Treatment of Unused Pin
Leaving unused input pins unconnected can cause abnormal operation or latch-up, leaving to permanent damage. Unused input pins should always be pulled up or down through resistance of at least 2 kΩ. Any unused
input/output pins may be set to output mode and left open, or set to input mode and treated the same as unused
input pins. If there is unused output pin, make it to open.
• Power Supply Pins
In products with multiple VCC or VSS pins, the pins of the same potential are internally connected in the device
to avoid abnormal operations including latch-up. However, you must connect the pins to external power supply
and a ground line to lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals
caused by the rise in the ground level, and to conform to the total output current rating.
Moreover, connect the current supply source with the VCC and VSS pins of this device at the low impedance.
It is also advisable to connect a ceramic bypass capacitor of approximately 0.1 µF between VCC and VSS pins
near this device.
14
MB95160M Series
• Mode Pin (MOD)
Connect the MOD pin directly to VCC or VSS.
To prevent the device unintentionally entering test mode due to noise, lay out the printed circuit board so as to
minimize the distance from the MOD pin to VCC or VSS and to provide a low-impedance connection.
Use a ceramic capacitor or a capacitor with equivalent frequency characteristics. A bypass capacitor of VCC pin
must have a capacitance value higher than CS. For connection of smoothing capacitor CS, refer to the diagram
below.
• C pin connection diagram
C
CS
• Analog Power Supply
Always set the same potential to AVCC and VCC pins. When VCC > AVCC, the current may flow through the AN00
to AN07 pins.
• Treatment of Power Supply Pins on A/D Converter
Connect to be AVCC = VCC and AVSS = AVR = VSS even if the A/D converter is not in use.
Noise riding on the AVCC pin may cause accuracy degradation. So, connect approx. 0.1 µF ceramic capacitor
as a bypass capacitor between AVCC and AVSS pins in the vicinity of this device.
15
MB95160M Series
■ PROGRAMMING FLASH MEMORY MICROCONTROLLERS USING PARALLEL
PROGRAMMER
• Supported Parallel Programmers and Adapters
The following table lists supported parallel programmers and adapters.
Package
Applicable adapter model
FPT-64P-M23
TEF110-95F168HPMC
FPT-64P-M24
TEF110-95F168HPMC1
Parallel programmers
AF9708 (Ver 02.35G or more)
AF9709/B (Ver 02.35G or more)
AF9723+AF9834 (Ver 02.08E or more)
Note : For information on applicable adapter models and parallel programmers, contact the following:
Flash Support Group, Inc. TEL: +81-53-428-8380
• Sector Configuration
The individual sectors of Flash memory correspond to addresses used for CPU access and programming by
the parallel programmer as follows:
Flash memory
CPU address
1000H
Programmer address*
11000H
FFFFH
1FFFFH
60 Kbytes
*: Programmer addresses are corresponding to CPU addresses, used when the parallel programmer
programs data into Flash memory.
These programmer addresses are used for the parallel programmer to program or erase data in
Flash memory.
• Programming Method
1) Set the type code of the parallel programmer to 17222.
2) Load program data to programmer addresses 11000H to 1FFFFH.
3) Programmed by parallel programmer
16
MB95160M Series
■ BLOCK DIAGRAM
F2MC-8FX CPU
RST
X0/X1
X0A/X1A
Reset control
ROM
RAM
Clock control
Interrupt control
Watch prescaler
Wild register
Watch counter
P00/INT00 to
P07/INT07
External interrupt
8/16-bit PPG ch.1
P10/UI0
P11/UO0
UART/SIO
8/16-bit
compound timer ch.1
P13/TRG0/ADTG
P14/PPG0
P20/PPG00
P21/PPG01
16-bit PPG
8/16-bit PPG ch.0
Internal bus
P12/UCK0
P24/EC0/SDA0
P61/SEG17/PPG11
P62/SEG18/TO10
P63/SEG19/TO11
P64/SEG20/EC1
P65/SEG21/SCK
LIN-UART
P66/SEG22/SOT
P67/SEG23/SIN
P90/V3 to P93/V0
P22/TO00
P23/TO01/SCL0
P60/SEG16/PPG10
8/16-bit
compound timer ch.0
LCDC
PA0/COM0 to PA3/COM3
PB0/SEG00 to PB7/SEG07
PC0/SEG08 to PC7/SEG15
I2C
(P00/SEG31 to P07/SEG24)
(P00/AN00 to
P07/AN07)
AVCC
AVSS
8/10-bit
A/D converter
P94/P95
AVR
Port
Port
Other pins
MOD, VSS, VCC, C
17
MB95160M Series
■ CPU CORE
1. Memory space
Memory space of the MB95160M series is 64 Kbytes and consists of I/O area, data area, and program area.
The memory space includes special-purpose areas such as the general-purpose registers and vector table.
Memory map of the MB95160M series is shown below.
• Memory Map
MB95F168M
MB95F168N
MB95F168J
0000H
MB95FV100D-103
0000H
I/O
0080H
RAM 2Kbytes
0100H Register
0200H
I/O
0080H
RAM 3.75Kbytes
0100H Register
0200H
0880H
Access prohibited
0F80H
0F80H
Exterded I/O
1000H
Exterded I/O
1000H
Flash memory
60Kbytes
FFFFH
18
Flash memory
60Kbytes
FFFFH
MB95160M Series
2. Register
The MB95160M series has two types of registers; dedicated registers in the CPU and general-purpose registers
in the memory. The dedicated registers are as follows:
Program counter (PC)
: A 16-bit register to indicate locations where instructions are stored.
Accumulator (A)
: A 16-bit register for temporary storage of arithmetic operations. In the case of
an 8-bit data processing instruction, the lower 1 byte is used.
Temporary accumulator (T) : A 16-bit register which performs arithmetic operations with the accumulator.
In the case of an 8-bit data processing instruction, the lower 1 byte is used.
Index register (IX)
: A 16-bit register for index modification.
Extra pointer (EP)
: A 16-bit pointer to point to a memory address.
Stack pointer (SP)
: A 16-bit register to indicate a stack area.
Program status (PS)
: A 16-bit register for storing a register bank pointer, a direct bank pointer, and
a condition code register.
Initial Value
16-bit
PC
: Program counter
FFFDH
AH
AL
: Accumulator
0000H
TH
TL
: Temporary accumulator
0000H
IX
: Index register
0000H
EP
: Extra pointer
0000H
SP
: Stack pointer
0000H
PS
: Program status
0030H
The PS can further be divided into higher 8 bits for use as a register bank pointer (RP) and a direct bank pointer
(DP) and the lower 8 bits for use as a condition code register (CCR). (Refer to the diagram below.)
• Structure of the Program Status
bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9
PS
R4
R3
R2
RP
R1
R0
DP2
DP1
DP
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
DP0
H
I
IL1
IL0
N
Z
V
C
CCR
19
MB95160M Series
The RP indicates the address of the register bank currently being used. The relationship between the content
of RP and the real address conforms to the conversion rule illustrated below:
• Rule for Conversion of Actual Addresses in the General-purpose Register Area
RP upper
"0"
"0"
"0"
"0"
"0"
"0"
"0"
"1"
R4
Generated address A15 A14 A13 A12 A11 A10 A9
A8
A7
R3
A6
R2
A5
R1
A4
OP code lower
R0
A3
b2
b1
A2
b0
A1
A0
The DP specifies the area for mapping instructions (16 different instructions such as MOV A, dir) using direct
addresses to 0080H to 00FFH.
Direct bank pointer (DP2 to DP0)
Specified address area
Mapping area
XXXB (no effect to mapping)
0000H to 007FH
0000H to 007FH (without mapping)
000B (initial value)
0080H to 00FFH (without mapping)
001B
0100H to 017FH
010B
0180H to 01FFH
011B
0080H to 00FFH
100B
0200H to 027FH
0280H to 02FFH
101B
0300H to 037FH
110B
0380H to 03FFH
111B
0400H to 047FH
The CCR consists of the bits indicating arithmetic operation results or transfer data contents and the bits that
control CPU operations at interrupt.
H flag
: Set to “1” when a carry or a borrow from bit 3 to bit 4 occurs as a result of an arithmetic operation.
Cleared to “0” otherwise. This flag is for decimal adjustment instructions.
I flag
: Interrupt is enabled when this flag is set to “1”. Interrupt is disabled when this flag is set to “0”.
The flag is set to “0” when reset.
IL1, IL0 : Indicates the level of the interrupt currently enabled. Processes an interrupt only if its request level
is higher than the value indicated by these bits.
IL1
IL0
Interrupt level
Priority
0
0
0
High
0
1
1
1
0
2
1
1
3
Low (no interruption)
N flag
: Set to “1” if the MSB is set to “1” as the result of an arithmetic operation. Cleared to “0” when the
Z flag
V flag
: Set to “1” when an arithmetic operation results in “0”. Cleared to “0” otherwise.
bit is set to “0”.
C flag
20
: Set to “1” if the complement on 2 overflows as a result of an arithmetic operation. Cleared to “0”
otherwise.
: Set to “1” when a carry or a borrow from bit 7 occurs as a result of an arithmetic operation. Cleared
to “0” otherwise. Set to the shift-out value in the case of a shift instruction.
MB95160M Series
The following general-purpose registers are provided:
General-purpose registers: 8-bit data storage registers
The general-purpose registers are 8 bits and located in the register banks on the memory. 1-bank contains
8-register. Up to a total of 32 banks can be used on the MB95160M series. The bank currently in use is specified
by the register bank pointer (RP), and the lower 3 bits of OP code indicates the general-purpose register 0 (R0)
to general-purpose register 7 (R7).
• Register Bank Configuration
8-bit
1F8H
This address = 0100H + 8 × (RP)
Address 100H
R0
R0
R0
R1
R2
R3
R4
R5
107H
R6
R1
R2
R3
R4
R5
R6
R1
R2
R3
R4
R5
R6
1FFH
R7
R7
R7
Bank 0
Memory area
Bank 31
32 banks
32 banks (RAM area)
The number of banks is
limited by the usable RAM
capacitance.
21
MB95160M Series
■ I/O MAP
Address
Register
abbreviation
Register name
R/W
Initial value
0000H
PDR0
Port 0 data register
R/W
00000000B
0001H
DDR0
Port 0 direction register
R/W
00000000B
0002H
PDR1
Port 1 data register
R/W
00000000B
0003H
DDR1
Port 1 direction register
R/W
00000000B
0004H
⎯
(Disabled)
⎯
⎯
0005H
WATR
Oscillation stabilization wait time setting register
R/W
11111111B
0006H
PLLC
PLL control register
R/W
00000000B
0007H
SYCC
System clock control register
R/W
1010X011B
0008H
STBC
Standby control register
R/W
00000000B
0009H
RSRR
Reset factor register
R/W
XXXXXXXXB
000AH
TBTC
Time-base timer control register
R/W
00000000B
000BH
WPCR
Watch prescaler control register
R/W
00000000B
000CH
WDTC
Watchdog timer control register
R/W
00000000B
000DH
⎯
(Disabled)
⎯
⎯
000EH
PDR2
Port 2 data register
R/W
00000000B
000FH
DDR2
Port 2 direction register
R/W
00000000B
0010H
to
0015H
⎯
(Disabled)
⎯
⎯
0016H
PDR6
Port 6 data register
R/W
00000000B
0017H
DDR6
Port 6 direction register
R/W
00000000B
0018H
to
001BH
⎯
(Disabled)
⎯
⎯
001CH
PDR9
Port 9 data register
R/W
00000000B
001DH
DDR9
Port 9 direction register
R/W
00000000B
001EH
PDRA
Port A data register
R/W
00000000B
001FH
DDRA
Port A direction register
R/W
00000000B
0020H
PDRB
Port B data register
R/W
00000000B
0021H
DDRB
Port B direction register
R/W
00000000B
0022H
PDRC
Port C data register
R/W
00000000B
0023H
DDRC
Port C direction register
R/W
00000000B
0024H
to
002CH
⎯
(Disabled)
⎯
⎯
(Continued)
22
MB95160M Series
Address
Register
abbreviation
Register name
R/W
Initial value
002DH
PUL1
Port 1 pull-up register
R/W
00000000B
002EH
PUL2
Port 2 pull-up register
R/W
00000000B
002FH
to
0035H
⎯
(Disabled)
⎯
⎯
0036H
T01CR1
8/16-bit compound timer 01 control status register 1 ch.0
R/W
00000000B
0037H
T00CR1
8/16-bit compound timer 00 control status register 1 ch.0
R/W
00000000B
0038H
T11CR1
8/16-bit compound timer 11 control status register 1 ch.1
R/W
00000000B
0039H
T10CR1
8/16-bit compound timer 10 control status register 1 ch.1
R/W
00000000B
003AH
PC01
8/16-bit PPG1 control register ch.0
R/W
00000000B
003BH
PC00
8/16-bit PPG0 control register ch.0
R/W
00000000B
003CH
PC11
8/16-bit PPG1 control register ch.1
R/W
00000000B
003DH
PC10
8/16-bit PPG0 control register ch.1
R/W
00000000B
003EH
to
0041H
⎯
(Disabled)
⎯
⎯
0042H
PCNTH0
16-bit PPG status control register (upper byte) ch.0
R/W
00000000B
0043H
PCNTL0
16-bit PPG status control register (lower byte) ch.0
R/W
00000000B
0044H
to
0047H
⎯
(Disabled)
⎯
⎯
0048H
EIC00
External interrupt circuit control register ch.0/ch.1
R/W
00000000B
0049H
EIC10
External interrupt circuit control register ch.2/ch.3
R/W
00000000B
004AH
EIC20
External interrupt circuit control register ch.4/ch.5
R/W
00000000B
004BH
EIC30
External interrupt circuit control register ch.6/ch.7
R/W
00000000B
004CH
to
004FH
⎯
(Disabled)
⎯
⎯
0050H
SCR
LIN-UART serial control register
R/W
00000000B
0051H
SMR
LIN-UART serial mode register
R/W
00000000B
0052H
SSR
LIN-UART serial status register
R/W
00001000B
0053H
RDR/TDR
LIN-UART reception/transmission data register
R/W
00000000B
0054H
ESCR
LIN-UART extended status control register
R/W
00000100B
0055H
ECCR
LIN-UART extended communication control register
R/W
000000XXB
0056H
SMC10
UART/SIO serial mode control register 1 ch.0
R/W
00000000B
0057H
SMC20
UART/SIO serial mode control register 2 ch.0
R/W
00100000B
0058H
SSR0
UART/SIO serial status register ch.0
R/W
00000001B
(Continued)
23
MB95160M Series
Address
Register
abbreviation
Register name
R/W
Initial value
0059H
TDR0
UART/SIO serial output data register ch. 0
R/W
00000000B
005AH
RDR0
UART/SIO serial input data register ch.0
R
00000000B
005BH
to
005FH
⎯
(Disabled)
⎯
⎯
0060H
IBCR00
I2C bus control register 0 ch.0
R/W
00000000B
R/W
00000000B
0061H
IBCR10
2
I C bus control register 1 ch.0
2
0062H
IBSR0
I C bus status register ch.0
R
00000000B
0063H
IDDR0
I2C data register ch.0
R/W
00000000B
0064H
IAAR0
I2C address register ch.0
R/W
00000000B
2
0065H
ICCR0
I C clock control register ch.0
R/W
00000000B
0066H
to
006BH
⎯
(Disabled)
⎯
⎯
006CH
ADC1
8/10-bit A/D converter control register 1
R/W
00000000B
006DH
ADC2
8/10-bit A/D converter control register 2
R/W
00000000B
006EH
ADDH
8/10-bit A/D converter data register (upper byte)
R/W
00000000B
006FH
ADDL
8/10-bit A/D converter data register (lower byte)
R/W
00000000B
0070H
WCSR
Watch counter status register
R/W
00000000B
0071H
⎯
(Disabled)
⎯
⎯
0072H
FSR
Flash memory status register
R/W
000X0000B
0073H
SWRE0
Flash memory sector writing control register 0
R/W
00000000B
0074H
SWRE1
Flash memory sector writing control register 1
R/W
00000000B
0075H
⎯
(Disabled)
⎯
⎯
0076H
WREN
Wild register address compare enable register
R/W
00000000B
0077H
WROR
Wild register data test setting register
R/W
00000000B
0078H
⎯
Register bank pointer (RP) ,
Mirror of direct bank pointer (DP)
⎯
⎯
0079H
ILR0
Interrupt level setting register 0
R/W
11111111B
007AH
ILR1
Interrupt level setting register 1
R/W
11111111B
007BH
ILR2
Interrupt level setting register 2
R/W
11111111B
007CH
ILR3
Interrupt level setting register 3
R/W
11111111B
007DH
ILR4
Interrupt level setting register 4
R/W
11111111B
007EH
ILR5
Interrupt level setting register 5
R/W
11111111B
007FH
⎯
(Disabled)
⎯
⎯
0F80H
WRARH0
Wild register address setting register (upper byte) ch.0
R/W
00000000B
(Continued)
24
MB95160M Series
Address
Register
abbreviation
Register name
R/W
Initial value
0F81H
WRARL0
Wild register address setting register (lower byte) ch.0
R/W
00000000B
0F82H
WRDR0
Wild register data setting register ch.0
R/W
00000000B
0F83H
WRARH1
Wild register address setting register (upper byte) ch.1
R/W
00000000B
0F84H
WRARL1
Wild register address setting register (lower byte) ch.1
R/W
00000000B
0F85H
WRDR1
Wild register data setting register ch.1
R/W
00000000B
0F86H
WRARH2
Wild register address setting register (upper byte) ch.2
R/W
00000000B
0F87H
WRARL2
Wild register address setting register (lower byte) ch.2
R/W
00000000B
0F88H
WRDR2
Wild register data setting register ch.2
R/W
00000000B
0F89H
to
0F91H
⎯
(Disabled)
⎯
⎯
0F92H
T01CR0
8/16-bit compound timer 01 control status register 0 ch.0
R/W
00000000B
0F93H
T00CR0
8/16-bit compound timer 00 control status register 0 ch.0
R/W
00000000B
0F94H
T01DR
8/16-bit compound timer 01 data register ch.0
R/W
00000000B
0F95H
T00DR
8/16-bit compound timer 00 data register ch.0
R/W
00000000B
0F96H
TMCR0
8/16-bit compound timer 00/01 timer mode control
register ch.0
R/W
00000000B
0F97H
T11CR0
8/16-bit compound timer 11 control status register 0 ch.1
R/W
00000000B
0F98H
T10CR0
8/16-bit compound timer 10 control status register 0 ch.1
R/W
00000000B
0F99H
T11DR
8/16-bit compound timer 11 data register ch.1
R/W
00000000B
0F9AH
T10DR
8/16-bit compound timer 10 data register ch.1
R/W
00000000B
0F9BH
TMCR1
8/16-bit compound timer 10/11 timer mode control
register ch.1
R/W
00000000B
0F9CH
PPS01
8/16-bit PPG1 cycle setting buffer register ch.0
R/W
11111111B
0F9DH
PPS00
8/16-bit PPG0 cycle setting buffer register ch.0
R/W
11111111B
0F9EH
PDS01
8/16-bit PPG1 duty setting buffer register ch.0
R/W
11111111B
0F9FH
PDS00
8/16-bit PPG0 duty setting buffer register ch.0
R/W
11111111B
0FA0H
PPS11
8/16-bit PPG1 cycle setting buffer register ch.1
R/W
11111111B
0FA1H
PPS10
8/16-bit PPG0 cycle setting buffer register ch.1
R/W
11111111B
0FA2H
PDS11
8/16-bit PPG1 duty setting buffer register ch.1
R/W
11111111B
0FA3H
PDS10
8/16-bit PPG0 duty setting buffer register ch.1
R/W
11111111B
0FA4H
PPGS
8/16-bit PPG start register
R/W
00000000B
0FA5H
REVC
8/16-bit PPG output inversion register
R/W
00000000B
0FA6H
to
0FA9H
⎯
(Disabled)
⎯
⎯
(Continued)
25
MB95160M Series
Address
Register
abbreviation
Register name
R/W
Initial value
0FAAH
PDCRH0
16-bit PPG down counter register (upper byte) ch.0
R
00000000B
0FABH
PDCRL0
16-bit PPG down counter register (lower byte) ch.0
R
00000000B
0FACH
PCSRH0
16-bit PPG cycle setting buffer register (upper byte) ch.0
R/W
11111111B
0FADH
PCSRL0
16-bit PPG cycle setting buffer register (lower byte) ch.0
R/W
11111111B
0FAEH
PDUTH0
16-bit PPG duty setting buffer register (upper byte) ch.0
R/W
11111111B
0FAFH
PDUTL0
16-bit PPG duty setting buffer register (lower byte) ch.0
R/W
11111111B
0FB0H
to
0FBBH
⎯
(Disabled)
⎯
⎯
0FBCH
BGR1
LIN-UART baud rate generator register 1
R/W
00000000B
0FBDH
BGR0
LIN-UART baud rate generator register 0
R/W
00000000B
0FBEH
PSSR0
UART/SIO dedicated baud rate generator prescaler selecting
register ch.0
R/W
00000000B
0FBFH
BRSR0
UART/SIO dedicated baud rate generator setting register ch.0
R/W
00000000B
0FC0H
to
0FC2H
⎯
(Disabled)
⎯
⎯
0FC3H
AIDRL
A/D input disable register (lower byte)
R/W
00000000B
0FC4H
LCDCC
LCDC control register
R/W
00010000B
0FC5H
LCDCE1
LCDC enable register 1
R/W
00110000B
0FC6H
LCDCE2
LCDC enable register 2
R/W
00000000B
0FC7H
LCDCE3
LCDC enable register 3
R/W
00000000B
0FC8H
LCDCE4
LCDC enable register 4
R/W
00000000B
0FC9H
LCDCE5
LCDC enable register 5
R/W
00000000B
0FCAH
⎯
(Disabled)
⎯
⎯
0FCBH
LCDCB1
LCDC blinking setting register 1
R/W
00000000B
0FCCH
LCDCB2
LCDC blinking setting register 2
R/W
00000000B
0FCDH
to
0FDCH
LCDRAM
LCDC display RAM
R/W
00000000B
0FDDH
to
0FE2H
⎯
(Disabled)
⎯
⎯
0FE3H
WCDR
Watch counter data register
R/W
00111111B
(Continued)
26
MB95160M Series
(Continued)
Address
Register
abbreviation
Register name
R/W
Initial value
0FE4H
to
0FE6H
⎯
(Disabled)
⎯
⎯
0FE7H
ILSR2
Input level select register 2
R/W
00000000B
0FE8H,
0FE9H
⎯
(Disabled)
⎯
⎯
0FEAH
CSVCR
Clock supervisor control register
R/W
00011100B
0FEBH
to
0FEDH
⎯
(Disabled)
⎯
⎯
0FEEH
ILSR
Input level selecting register
R/W
00000000B
0FEFH
WICR
Interrupt pin control register
R/W
01000000B
0FF0H
to
0FFFH
⎯
(Disabled)
⎯
⎯
• R/W access symbols
R/W : Readable/Writable
R
: Read only
W
: Write only
• Initial value symbols
0 : The initial value of this bit is “0”.
1 : The initial value of this bit is “1”.
X : The initial value of this bit is undefined.
Note : Do not write to the “ (Disabled) ”. Reading the “ (Disabled) ” returns an undefined value.
27
MB95160M Series
■ INTERRUPT SOURCE TABLE
Interrupt source
Vector table address
Same level
Bit name of
priority order
interrupt level
(at simultaneous
setting register
occurrence)
Upper
Lower
IRQ0
FFFAH
FFFBH
L00 [1 : 0]
IRQ1
FFF8H
FFF9H
L01 [1 : 0]
IRQ2
FFF6H
FFF7H
L02 [1 : 0]
IRQ3
FFF4H
FFF5H
L03 [1 : 0]
UART/SIO ch.0
IRQ4
FFF2H
FFF3H
L04 [1 : 0]
8/16-bit compound timer ch.0 (Lower)
IRQ5
FFF0H
FFF1H
L05 [1 : 0]
8/16-bit compound timer ch.0 (Upper)
IRQ6
FFEEH
FFEFH
L06 [1 : 0]
LIN-UART (reception)
IRQ7
FFECH
FFEDH
L07 [1 : 0]
LIN-UART (transmission)
IRQ8
FFEAH
FFEBH
L08 [1 : 0]
8/16-bit PPG ch.1 (Lower)
IRQ9
FFE8H
FFE9H
L09 [1 : 0]
8/16-bit PPG ch.1 (Upper)
IRQ10
FFE6H
FFE7H
L10 [1 : 0]
(Unused)
IRQ11
FFE4H
FFE5H
L11 [1 : 0]
8/16-bit PPG ch.0 (Upper)
IRQ12
FFE2H
FFE3H
L12 [1 : 0]
8/16-bit PPG ch.0 (Lower)
IRQ13
FFE0H
FFE1H
L13 [1 : 0]
8/16-bit compound timer ch.1 (Upper)
IRQ14
FFDEH
FFDFH
L14 [1 : 0]
16-bit PPG ch.0
IRQ15
FFDCH
FFDDH
L15 [1 : 0]
I2C ch.0
IRQ16
FFDAH
FFDBH
L16 [1 : 0]
(Unused)
IRQ17
FFD8H
FFD9H
L17 [1 : 0]
8/10-bit A/D converter
IRQ18
FFD6H
FFD7H
L18 [1 : 0]
Time-base timer
IRQ19
FFD4H
FFD5H
L19 [1 : 0]
Watch prescaler/Watch counter
IRQ20
FFD2H
FFD3H
L20 [1 : 0]
(Unused)
IRQ21
FFD0H
FFD1H
L21 [1 : 0]
8/16-bit compound timer ch.1 (Lower)
IRQ22
FFCEH
FFCFH
L22 [1 : 0]
Flash memory
IRQ23
FFCCH
FFCDH
L23 [1 : 0]
External interrupt ch.0
External interrupt ch.4
External interrupt ch.1
External interrupt ch.5
External interrupt ch.2
External interrupt ch.6
External interrupt ch.3
External interrupt ch.7
28
Interrupt
request
number
High
Low
MB95160M Series
■ ELECTRICAL CHARACTERISTICS
1. Absolute Maximum Ratings
Parameter
Symbol
Rating
Unit
Remarks
Min
Max
VCC,
AVCC
Vss − 0.3
Vss + 6.0
AVR
Vss − 0.3
Vss + 6.0
V0 to V3
Vss − 0.3
Vss + 6.0
V
*3
Input voltage*1
VI
Vss − 0.3
Vss + 6.0
V
*4
Output voltage*1
VO
Vss − 0.3
Vss + 6.0
V
*4
ICLAMP
− 2.0
+ 2.0
mA
Applicable to pins*5
Σ|ICLAMP|
⎯
20
mA
Applicable to pins*5
IOL
⎯
15
mA
Applicable to pins*5
Applicable to pins*5
Average output current =
operating current × operating ratio
(1 pin)
Power supply voltage*
1
Power supply voltage
for LCD
Maximum clamp current
Total maximum clamp
current
“L” level maximum
output current
V
*2
*2
“L” level average
current
IOLAV
⎯
4
mA
“L” level total maximum
output current
ΣIOL
⎯
100
mA
ΣIOLAV
⎯
50
mA
Total average output current =
operating current × operating ratio
(Total of pins)
IOH
⎯
− 15
mA
Applicable to pins*5
Applicable to pins*5
Average output current =
operating current × operating ratio
(1 pin)
“L” level total average
output current
“H” level maximum
output current
“H” level average
current
IOHAV
⎯
−4
mA
“H” level total maximum
output current
ΣIOH
⎯
− 100
mA
ΣIOHAV
⎯
− 50
mA
Power consumption
Pd
⎯
320
mW
Operating temperature
TA
− 10
+ 85
°C
Tstg
− 55
+ 150
°C
“H” level total average
output current
Storage temperature
Total average output current =
operating current × operating ratio
(Total of pins)
(Continued)
29
MB95160M Series
(Continued)
*1 : The parameter is based on VSS = 0.0 V.
*2 : Apply equal potential to AVCC and VCC. AVR should not exceed AVCC + 0.3 V.
*3 : V0 to V3 should not exceed VCC + 0.3 V.
*4 : VI and Vo should not exceed VCC + 0.3 V. VI must not exceed the rating voltage. However, if the maximum current
to/from an input is limited by some means with external components, the ICLAMP rating supersedes the VI rating.
*5 : Applicable to pins :
P00 to P07, P10 to P14, P20 to P22,P60 to P67, P90 to P95, PA0 to PA3, PB0 to PB7, PC0 to PC7
• Use within recommended operating conditions.
• Use at DC voltage (current).
• + B signal is an input signal that exceeds VCC voltage. The + B signal should always be applied a limiting
resistance placed between the + B signal and the microcontroller.
• The value of the limiting resistance should be set so that when the + B signal is applied the input current
to the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
• Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input
potential may pass through the protective diode and increase the potential at the VCC pin, and this affects
other devices.
• Note that if the + B signal is inputted when the microcontroller power supply is off (not fixed at 0 V), the power
supply is provided from the pins, so that incomplete operation may result.
• Note that if the + B input is applied during power-on, the power supply is provided from the pins and the
resulting power supply voltage may not be sufficient to operate the power-on reset.
• Care must be taken not to leave the + B input pin open.
• Note that analog system input/output pins other than the A/D input pins (LCD drive pins, etc.) cannot accept
+ B signal input.
• Sample recommended circuits :
• Input/Output Equivalent circuits
Protective diode
+ B input (0 V to 16 V)
Vcc
Limiting
resistance
P-ch
N-ch
R
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
30
MB95160M Series
2. Recommended Operating Conditions
(Vss = 0.0 V)
Parameter
Symbol
Conditions
Value
Unit
Remarks
Min
Max
2.42*1,*2
5.5*1
2.3
5.5
2.7
5.5
2.3
5.5
MB95FV100DHold condition in STOP 103
mode
VSS
VCC
V
The range of liquid crystal power supply:
without up-conversion (The optimal value
depends on liquid crystal display elements
used.)
AVR
4.0
AVCC
V
Smoothing capacitor
CS
0.1
1.0
µF
*3
Operating temperature
TA
− 10
+ 85
°C
Other than MB95FV100D-103
+5
+35
°C
MB95FV100D-103
Power supply
voltage
Power supply
voltage for LCD
A/D converter
reference input voltage
VCC,
AVCC
V0
to
V3
⎯
In normal operating
V
Other than
Hold condition in STOP MB95FV100D103
mode
In normal operating
*1 : The values vary with the operating frequency, machine clock or analog guarantee range.
*2 : The value is 2.88 V when the low voltage detection reset is used. The device operates normally during the time
between 2.88 V and low voltage detection, and between release voltage and 2.88 V.
(Continued)
31
MB95160M Series
(Continued)
*3 : Use a ceramic capacitor or a capacitor with equivalent frequency characteristics. A bypass capacitor of VCC
pin must have a capacitor value higher than CS. For connection of smoothing capacitor CS, refer to the diagram
below.
• C pin connection diagram
C
CS
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the
semiconductor device. All of the device’s electrical characteristics are warranted when the device is
operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges. Operation
outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact their
FUJITSU representatives beforehand.
32
MB95160M Series
3. DC Characteristics
(Vcc = 5.0 V ± 10%, Vss = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
Symbol
Pin name
Value
Min
Typ
Max
Unit
Remarks
When selecting
CMOS input level
VIH1
P10, P67
*1
0.7 VCC
⎯
VCC + 0.3
V
VIH2
P23, P24
*1
0.7 VCC
⎯
VSS + 5.5
V
VIHA
P00 to P07,
P10 to P14,
P20 to P22,
P60 to P67,
P90 to P95,
PA0 to PA3,
PB0 to PB7,
PC0 to PC7
⎯
0.8 VCC
⎯
VCC + 0.3
V
Port inputs if Automotive input levels
are selected
VIHS1
P00 to P07,
P10 to P14,
P20 to P22,
P60 to P67,
P90 to P95,
PA0 to PA3,
PB0 to PB7,
PC0 to PC7
*1
0.8 VCC
⎯
VCC + 0.3
V
Hysteresis input
VIHS2 P23, P24
*1
0.8 VCC
⎯
VSS + 5.5
V
VIHM RST, MOD
⎯
0.7 VCC
⎯
VCC + 0.3
V
CMOS input
“H” level input
voltage
VIL
P10,P23, P24,P67
*1
VSS − 0.3
⎯
0.3 VCC
V
Hysteresis input
(When selecting
CMOS input level)
VILA
P00 to P07,
P10 to P14,
P20 to P24,
P60 to P67,
P90 to P95,
PA0 to PA3,
PB0 to PB7,
PC0 to PC7
⎯
VSS − 0.3
⎯
0.5 VCC
V
Port inputs if
Automotive input
levels are selected
VILS
P00 to P07,
P10 to P14,
P20 to P24,
P60 to P67,
P90 to P95,
PA0 to PA3,
PB0 to PB7,
PC0 to PC7
*1
VSS − 0.3
⎯
0.2 VCC
V
Hysteresis input
⎯
VSS − 0.3
⎯
0.3 VCC
V
Hysteresis input
Vcc − 0.5
⎯
⎯
V
“L” level input
voltage
VILM RST, MOD
“H” level
output voltage
Conditions
VOH
Output pins other
than P00 to P07
IOH =
− 4.0 mA
(Continued)
33
MB95160M Series
(Vcc = 5.0 V ± 10%, Vss = 0.0 V, TA = − 40 °C to + 85 °C)
Value
Conditions
Unit
Remarks
Min Typ Max
Parameter
Symbol
“L” level output
voltage
VOL
Output pins other
than P00 to P07,
RST*2
IOL = 4.0 mA
⎯
⎯
0.4
V
Input leakage
current (Hi-Z
output leakage
current)
ILI
Ports other than
P23, P24
0.0 V < VI < VCC
−5
⎯
+5
µA
When the pull-up
prohibition setting
Pull-up resistor RPULL
P10 to P14,
P20 to P22
VI = 0.0 V
25
50
100
kΩ
When the pull-up
permission setting
Input
capacitance
Other than AVCC,
f = 1 MHz
AVSS, AVR, VCC, VSS
⎯
5
15
pF
FCH = 20 MHz
FMP = 10 MHz
Main clock mode
(divided by 2)
⎯
9.5
12.5
At other than Flash
mA memory writing
and erasing
⎯
30.0
35.0
mA
FCH = 32 MHz
FMP = 16 MHz
Main clock mode
(divided by 2)
⎯
15.2
20.0
At other than Flash
mA memory writing
and erasing
⎯
35.7
42.5
mA
FCH = 20 MHz
FMP = 10 MHz
Main Sleep mode
(divided by 2)
⎯
4.5
7.5
mA
FCH = 32 MHz
FMP = 16 MHz
Main Sleep mode
(divided by 2)
⎯
7.2
12.0
mA
ICCL
FCL = 32 kHz
FMPL = 16 kHz
Sub clock mode
(divided by 2)
TA = + 25 °C
⎯
45
100
µA
ICCLS
FCL = 32 kHz
FMPL = 16 kHz
Sub sleep mode
(divided by 2)
TA = + 25 °C
⎯
10
81
µA
ICCT
FCL = 32 kHz
Watch mode
Main stop mode
TA = + 25 °C
⎯
4.6
27.0
µA
CIN
Pin name
ICC
ICCS
VCC
(External clock
operation)
Power supply
current*3
At Flash memory
writing and erasing
At Flash memory
writing and erasing
(Continued)
34
MB95160M Series
(Continued)
Parameter
(Vcc = 5.0 V ± 10%, Vss = 0.0 V, TA = − 40 °C to + 85 °C)
Symbol
Pin name
Conditions
Value
Unit Remarks
Min
Typ
Max
FCH = 4 MHz
FMP = 10 MHz
Main PLL mode
(multiplied by 2.5)
⎯
9.3
12.5
mA
FCH = 6.4 MHz
FMP = 16 MHz
Main PLL mode
(multiplied by 2.5)
⎯
14.9
20.0
mA
FCL = 32 kHz
FMPL = 128 kHz
Sub PLL mode
(multiplied by 4) ,
TA = + 25 °C
⎯
160
400
µA
ICTS
FCH = 10 MHz
Time-base timer
mode
TA = + 25 °C
⎯
0.15
1.10
mA
ICCH
Sub stop mode
TA = + 25 °C
⎯
5
20
µA
FCH = 16 MHz
At operating of A/D
conversion
⎯
2.4
4.7
mA
FCH = 16 MHz
At stopping of A/D
conversion
TA = + 25 °C
⎯
1
5
µA
Between V3 and VSS
⎯
300
⎯
kΩ
⎯
⎯
5
kΩ
⎯
⎯
7
kΩ
−1
⎯
+1
µA
ICCMPLL
ICCSPLL
VCC
(External clock
operation)
Power supply
current*3
IA
AVCC
IAH
LCD internal
division resistance
RLCD
⎯
COM0 to COM3
output impedance
RVCOM
COM0 to COM3
SEG00 to SEG31
output impedance
RVSEG SEG00 to SEG31
LCD leak current
ILCDL
V1 to V3 = 5.0 V
V0 to V3,
COM0 to COM3
SEG00 to SEG31
⎯
*1 : The value is 2.88 V when the low voltage detection reset is used.
*2 : Product without clock supervisor only
*3 : • The power-supply current is determined by the external clock. When both low voltage detection option
and clock supervisor option are selected, the power-supply current will be a value of adding current
consumption of the low voltage detection circuit (ILVD) and current consumption of built-in CR oscillator (ICSV)
to the specified value.
• Refer to “4. AC Characteristics (1) Clock Timing” for FCH and FCL.
• Refer to “4. AC Characteristics (2) Source Clock/Machine Clock” for FMP and FMPL.
35
MB95160M Series
4. AC Characteristics
(1) Clock Timing
(Vcc = 2.42 V to 5.5 V, Vss = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
SymPin name Conditions
bol
FCH
X0, X1
Clock frequency
FCL
X0A, X1A
⎯
Clock cycle time
Input clock pulse
width
Input clock rise time
and fall time
36
tHCYL
X0, X1
Value
Unit
Remarks
16.25
MHz
When using main
oscillation circuit
⎯
32.50
MHz When using external clock
3.00
⎯
10.00
MHz Main PLL multiplied by 1
3.00
⎯
8.13
MHz Main PLL multiplied by 2
3.00
⎯
6.50
MHz Main PLL multiplied by 2.5
3.00
⎯
4.06
MHz Main PLL multiplied by 4
⎯
32.768
⎯
kHz
When using sub
oscillation circuit
⎯
32.768
⎯
kHz
When using sub PLL
61.5
⎯
1000
ns
When using oscillation
circuit
30.8
⎯
1000
ns
When using external clock
Min
Typ
Max
1.00
⎯
1.00
tLCYL
X0A, X1A
⎯
30.5
⎯
µs
When using sub clock
tWH1
tWL1
X0
61.5
⎯
⎯
ns
tWH2
tWL2
X0A
⎯
15.2
⎯
µs
When using external clock
Duty ratio is about 30% to
70%.
tCR
tCF
X0, X0A
⎯
⎯
5
ns
When using external clock
MB95160M Series
• Input wave form for using external clock (main clock)
tHCYL
tWH1
tWL1
tCR
tCF
0.8 VCC 0.8 VCC
X0
0.2 VCC
0.2 VCC
0.2 VCC
• Figure of Main Clock Input Port External Connection
When using a crystal or
ceramic oscillator
When using external clock
Microcontroller
Microcontroller
X0
X1
X0
X1
Open
FCH
FCH
C1
C2
• Input wave form for using external clock (sub clock)
tLCYL
tWH2
tCR
tWL2
tCF
0.8 VCC 0.8 VCC
X0A
0.2 VCC
0.2 VCC
0.2 VCC
• Figure of Sub clock Input Port External Connection
When using a crystal or
ceramic oscillator
Microcontroller
X0A
X1A
When using external clock
Microcontroller
X0A
FCL
X1A
Open
FCL
C1
C2
37
MB95160M Series
(2) Source Clock/Machine Clock
(Vcc = 5.0 V ± 10%, Vss = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
Sym- Condibol tions
Machine clock cycle
time*2
(Minimum instruction
execution time)
Machine clock
frequency
Min
Typ
Max
Unit
Remarks
61.5
⎯
2000
ns
When using main clock
Min : FCH = 8.125 MHz,
PLL multiplied by 2
Max : FCH = 1 MHz, divided by 2
7.6
⎯
61.0
µs
When using sub clock
Min : FCL = 32 kHz, PLL multiplied by 4
Max : FCL = 32 kHz, divided by 2
0.50
⎯
16.25
16.384
⎯
61.5
⎯
32000
ns
When using main clock
Min : FSP = 16.25 MHz, no division
Max : FSP = 0.5 MHz, divided by 16
7.6
⎯
976.5
µs
When using sub clock
Min : FSPL = 131 kHz, no division
Max : FSPL = 16 kHz, divided by 16
FMP
0.031
⎯
16.250
FMPL
1.024
⎯
131.072 kHz When using sub clock
Source clock cycle time*1
(Clock before setting
tSCLK
division)
Source clock frequency
Value
FSP
FSPL
⎯
MHz When using main clock
131.072 kHz When using sub clock
tMCLK
MHz When using main clock
*1 : Clock before setting division due to machine clock division ratio selection bit (SYCC : DIV1 and DIV0) . This
source clock is divided by the machine clock division ratio selection bit (SYCC : DIV1 and DIV0) , and it
becomes the machine clock. Further, the source clock can be selected as follows.
• Main clock divided by 2
• PLL multiplication of main clock (select from 1, 2, 2.5, 4 multiplication)
• Sub clock divided by 2
• PLL multiplication of sub clock (select from 2, 3, 4 multiplication)
*2 : Operation clock of the microcontroller. Machine clock can be selected as follows.
• Source clock (no division)
• Source clock divided by 4
• Source clock divided by 8
• Source clock divided by 16
38
MB95160M Series
• Outline of clock generation block
FCH
(main oscillation)
Divided by 2
Main PLL
×1
×2
× 2.5
×4
SCLK
( source clock )
FCL
(sub oscillation)
Divided by 2
Sub PLL
×2
×3
×4
Division
circuit
×1
× 1/4
× 1/8
× 1/16
MCLK
( machine clock )
Clock mode select bit
( SYCC : SCS1, SCS0 )
39
MB95160M Series
• Operating voltage - Operating frequency (When TA = − 40 °C to + 85 °C)
• MB95F168M/F168N/F168J
Main clock mode and main PLL mode
operation guarantee range
Sub PLL, sub clock mode and
watch mode operation guarantee range
5.5
2.42
16.384 kHz
32 kHz
131.072 kHz
Operating voltage (V)
Operating voltage (V)
5.5
3.5
2.42
0.5 MHz 3 MHz
10 MHz
16.25 MHz
PLL operation guarantee range
PLL operation guarantee range
Main clock operation guarantee range
Source clock frequency (FSP)
Source clock frequency (FSPL)
• Operating voltage - Operating frequency (When TA = + 5 °C to + 35 °C)
• MB95FV100D-103
Main clock mode and main PLL mode
operation guarantee range
Sub PLL, sub clock mode and
watch mode operation guarantee range
5.5
2.7
16.384 kHz
32 kHz
131.072 kHz
PLL operation guarantee range
Source clock frequency (FSP)
40
Operating voltage (V)
Operating voltage (V)
5.5
3.5
2.7
0.5MHz 3 MHz
10 MHz
16.25 MHz
PLL operation guarantee range
Main clock operation guarantee range
Source clock frequency (FSP)
MB95160M Series
• Main PLL operation frequency
[MHz]
16.25
16
15
×4
12
× 2.5
Source clock frequency (FSP)
10
×1
×2
7.5
6
5
3
0
3
4
5
4.062
6.4
6.5
10 [MHz]
8
8.125
Main clock frequency (FMP)
41
MB95160M Series
(3) External Reset
(Vcc = 5.0 V ± 10%, Vss = 0.0 V, TA = − 40 °C to + 85 °C)
Symbol
Parameter
RST “L” level
pulse width
tRSTL
Pin
name
RST
Value
Conditions
⎯
Min
Max
2 tMCLK*1
⎯
Unit
Remarks
ns
At normal operating
Oscillation time of oscillator*2
+ 100
⎯
µs
At stop mode,
sub clock mode,
sub sleep mode,
and watch mode
100
⎯
µs
At time-base timer
mode
*1 : Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
*2 : Oscillation time of oscillator is the time that the amplitude reaches 90%. In the crystal oscillator, the oscillation
time is between several ms and tens of ms. In ceramic oscillators, the oscillation time is between hundreds of
µs and several ms. In the external clock, the oscillation time is 0 ms.
• At normal operating
tRSTL
RST
0.2 VCC
0.2 VCC
• At stop mode, sub clock mode, sub sleep mode, watch mode, and power-on
RST
tRSTL
0.2 VCC
0.2 VCC
90% of
amplitude
X0
Internal
operating
clock
Oscillation
time of
oscillator
Internal reset
42
100 µs
Oscillation stabilization wait time
Execute instruction
MB95160M Series
(4) Power-on Reset
(Vss = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
Symbol
Power supply rising
time
tR
Power supply cutoff
time
tOFF
Pin name
Value
Conditions
Unit
Min
Max
⎯
50
ms
1
⎯
ms
⎯
VCC
tR
Remarks
Waiting time until
power-on
tOFF
2.5 V
VCC
0.2 V
0.2 V
0.2 V
Note : Sudden change of power supply voltage may activate the power-on reset function. When changing power
supply voltages during operation, set the slope of rising within 30 mV/ms as shown below.
VCC
Limiting the slope of rising within
30 mV/ms is recommended.
2.3 V
Hold condition in stop mode
VSS
43
MB95160M Series
(5) Peripheral Input Timing
(Vcc = 5.0 V ± 10%, Vss = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
Symbol
Peripheral input
“H” pulse width
tILIH
Peripheral input
“L” pulse width
tIHIL
Pin name
INT00 to INT07,
EC0, EC1, TRG0/ADTG
Conditions
Value
Max
2 tMCLK*
⎯
ns
2 tMCLK*
⎯
ns
⎯
* : Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
tILIH
INT00 to INT07,
EC0, EC1,
TRG0/ADTG
44
Unit
Min
tIHIL
0.8 VCC 0.8 VCC
0.2 VCC
0.2 VCC
MB95160M Series
(6) UART/SIO, Serial I/O Timing
(Vcc = 5.0 V ± 10%, Vss = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
Symbol
Pin name
Serial clock cycle time
tSCYC
UCK0
UCK ↓ → UO time
tSLOV
UCK0, UO0
Valid UI → UCK ↑
tIVSH
UCK0, UI0
UCK ↑ → valid UI hold time
tSHIX
UCK0, UI0
Serial clock “H” pulse width
tSHSL
UCK0
Serial clock “L” pulse width
tSLSH
UCK0
UCK ↓ → UO time
tSLOV
UCK0, UO0
Valid UI → UCK ↑
tIVSH
UCK0, UI0
UCK ↑ → valid UI hold time
tSHIX
UCK0, UI0
Value
Conditions
Internal clock
operation
output pin : CL = 80 pF
+ 1TTL.
External clock
operation
output pin : CL = 80 pF
+ 1TTL.
Unit
Min
Max
4 tMCLK*
⎯
ns
− 190
+ 190
ns
2 tMCLK*
⎯
ns
2 tMCLK*
⎯
ns
4 tMCLK*
⎯
ns
4 tMCLK*
⎯
ns
⎯
190
ns
2 tMCLK*
⎯
ns
2 tMCLK*
⎯
ns
* : Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
• Internal shift clock mode
tSCYC
UCK0
2.4 V
0.8 V
0.8 V
tSLOV
UO0
UI0
2.4 V
0.8 V
tIVSH
tSHIX
0.8 VCC
0.2 VCC
0.8 VCC
0.2 VCC
• External shift clock mode
tSLSH
tSHSL
0.8 VCC 0.8 VCC
UCK0
0.2 VCC 0.2 VCC
tSLOV
UO0
UI0
2.4 V
0.8 V
tIVSH
tSHIX
0.8 VCC
0.2 VCC
0.8 VCC
0.2 VCC
45
MB95160M Series
(7) LIN-UART Timing
Sampling at the rising edge of sampling clock*1 and prohibited serial clock delay*2
(ESCR register : SCES bit = 0, ECCR register : SCDE bit = 0)
(Vcc = 5.0 V ± 10%, Vss = 0.0 V, TA = −40 °C to + 85 °C)
Parameter
Serial clock cycle time
SymPin name
bol
tSCYC
SCK ↓ → SOT delay time
tSLOVI
Valid SIN → SCK ↑
tIVSHI
SCK ↑ → valid SIN hold time
tSHIXI
Serial clock “L” pulse width
tSLSH
Serial clock “H” pulse width
tSHSL
Value
Conditions
Max
5 tMCLK*3
⎯
ns
+ 95
ns
⎯
ns
⎯
ns
3 tMCLK*3 − tR
⎯
ns
* + 95
⎯
ns
SCK
Internal clock
SCK, SOT
−95
operation output pin :
SCK, SIN CL = 80 pF + 1 TTL. tMCLK*3 + 190
SCK, SIN
0
SCK
SCK
Unit
Min
t
MCLK 3
⎯
* + 95
SCK ↓ → SOT delay time
tSLOVE SCK, SOT
Valid SIN → SCK ↑
tIVSHE
SCK, SIN
SCK ↑ → valid SIN hold time
tSHIXE
SCK, SIN
SCK fall time
tF
SCK
⎯
10
ns
SCK rise time
tR
SCK
⎯
10
ns
External clock
operation output pin :
CL = 80 pF + 1 TTL.
MCLK 3
ns
190
⎯
ns
tMCLK*3 + 95
⎯
ns
2t
*1 : Provide switch function whether sampling of reception data is performed at rising edge or falling edge of the
serial clock.
*2 : Serial clock delay function is used to delay half clock for the output signal of serial clock.
*3 : Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
46
MB95160M Series
• Internal shift clock mode
tSCYC
2.4 V
SCK
0.8 V
0.8 V
tSLOVI
2.4 V
SOT
0.8 V
tIVSHI
tSHIXI
0.8 VCC 0.8 VCC
SIN
0.2 VCC 0.2 VCC
• External shift clock mode
tSHSL
tSLSH
SCK
0.8 VCC
0.2 VCC
tF
SOT
0.8 VCC
0.2 VCC
tR
tSLOVE
2.4 V
0.8 V
tIVSHE
SIN
tSHIXE
0.8 VCC 0.8 VCC
0.2 VCC 0.2 VCC
47
MB95160M Series
Sampling at the falling edge of sampling clock*1 and prohibited serial clock delay*2
(ESCR register : SCES bit = 1, ECCR register : SCDE bit = 0)
(VCC = 5.0 V ± 10%, VSS = 0.0 V, TA = −40 °C to + 85 °C)
Symbol
Pin name
Serial clock cycle time
tSCYC
SCK
SCK↑→ SOT delay time
tSHOVI
SCK, SOT
Parameter
Value
Conditions
Internal clock
operation output pin :
SCK, SIN CL = 80 pF + 1 TTL.
SCK, SIN
t
Unit
Min
Max
5 tMCLK*3
⎯
ns
−95
+ 95
ns
⎯
ns
0
⎯
ns
* + 190
MCLK 3
Valid SIN→SCK↓
tIVSLI
SCK↓→ valid SIN hold time
tSLIXI
Serial clock “H” pulse width
tSHSL
SCK
3 tMCLK*3 − tR
⎯
ns
Serial clock “L” pulse width
tSLSH
SCK
tMCLK*3 + 95
⎯
ns
SCK, SOT
⎯
SCK↑ →SOT delay time
tSHOVE
Valid SIN→SCK↓
tIVSLE
SCK↓→ valid SIN hold time
tSLIXE
External clock
SCK, SIN operation output pin :
SCK, SIN CL = 80 pF + 1 TTL.
* + 95
MCLK 3
ns
190
⎯
ns
tMCLK*3 + 95
⎯
ns
2t
SCK fall time
tF
SCK
⎯
10
ns
SCK rise time
tR
SCK
⎯
10
ns
*1 : Provide switch function whether sampling of reception data is performed at rising edge or falling edge of
the serial clock.
*2 : Serial clock delay function is used to delay half clock for the output signal of serial clock.
*3 : Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
48
MB95160M Series
• Internal shift clock mode
tSCYC
2.4 V
SCK
2.4 V
0.8 V
tSHOVI
2.4 V
SOT
0.8 V
tIVSLI
tSLIXI
0.8 VCC 0.8 VCC
SIN
0.2 VCC 0.2 VCC
• External shift clock mode
tSHSL
SCK
0.8 VCC
tSLSH
0.8 VCC
0.2 VCC
tR
SOT
0.2 VCC
0.2 VCC
tF
tSHOVE
2.4 V
0.8 V
tIVSLE
SIN
tSLIXE
0.8 VCC 0.8 VCC
0.2 VCC 0.2 VCC
49
MB95160M Series
Sampling at the rising edge of sampling clock*1 and enabled serial clock delay*2
(ESCR register : SCES bit = 0, ECCR register : SCDE bit = 1)
(VCC = 5.0 V ± 10%, VSS = 0.0 V, TA = −40 °C to + 85 °C)
Symbol
Pin name
Serial clock cycle time
tSCYC
SCK
SCK↑→ SOT delay time
tSHOVI
SCK, SOT
Parameter
Valid SIN→SCK↓
tIVSLI
SCK, SIN
SCK↓→ valid SIN hold time
tSLIXI
SCK, SIN
SOT→SCK↓ delay time
tSOVLI
SCK, SOT
Value
Conditions
Internal clock
operation output pin :
CL = 80 pF + 1 TTL.
Max
5 tMCLK*3
⎯
ns
−95
+ 95
ns
⎯
ns
0
⎯
ns
⎯
4 tMCLK*3
ns
* + 190
MCLK 3
t
Unit
Min
*1 : Provide switch function whether sampling of reception data is performed at rising edge or falling edge of
the serial clock.
*2 : Serial clock delay function is used to delay half clock for the output signal of serial clock.
*3 : Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
tSCYC
2.4 V
SCK
0.8 V
SOT
2.4 V
0.8 V
2.4 V
0.8 V
tIVSLI
SIN
50
0.8 V
tSHOVI
tSOVLI
0.8 VCC
0.2 VCC
tSLIXI
0.8 VCC
0.2 VCC
MB95160M Series
Sampling at the falling edge of sampling clock*1 and enabled serial clock delay*2
(ESCR register : SCES bit = 1, ECCR register : SCDE bit = 1)
(VCC = 5.0 V ± 10%, VSS = 0.0 V, TA = −40 °C to + 85 °C)
Symbol
Pin name
Serial clock cycle time
tSCYC
SCK↓→SOT delay time
tSLOVI
Parameter
Value
Conditions
Unit
Min
Max
SCK
5 tMCLK*3
⎯
ns
SCK, SOT
−95
+ 95
ns
⎯
ns
0
⎯
ns
⎯
4 tMCLK*3
ns
Valid SIN→SCK↑
tIVSHI
SCK↑ → valid SIN hold time
tSHIXI
Internal clock
SCK, SIN operation output pin :
CL = 80 pF + 1 TTL.
SCK, SIN
SOT→SCK↑ delay time
tSOVHI
SCK, SOT
* + 190
MCLK 3
t
*1 : Provide switch function whether sampling of reception data is performed at rising edge or falling edge of the
serial clock.
*2 : Serial clock delay function is used to delay half clock for the output signal of serial clock.
*3 : Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
tSCYC
2.4 V
SCK
2.4 V
0.8 V
tSOVHI
SOT
2.4 V
0.8 V
tIVSHI
SIN
tSLOVI
2.4 V
0.8 V
0.8 VCC
0.2 VCC
tSHIXI
0.8 VCC
0.2 VCC
51
MB95160M Series
(8) I2C Timing
(VCC = 5.0 V ± 10%, AVSS = VSS = 0.0 V, TA = − 40 °C to + 85 °C)
Value
Parameter
Symbol
Pin
name
Conditions Standard-mode
Fast-mode
Min
Max
Min
Max
Unit
fSCL
SCL0
0
100
0
400
kHz
tHD;STA
SCL0
SDA0
4.0
⎯
0.6
⎯
µs
SCL clock “L” width
tLOW
SCL0
4.7
⎯
1.3
⎯
µs
SCL clock “H” width
tHIGH
SCL0
4.0
⎯
0.6
⎯
µs
(Repeat) Start condition setup time
SCL ↑ → SDA ↓
tSU;STA
SCL0
SDA0
4.7
⎯
0.6
⎯
µs
Data hold time SCL ↓ → SDA ↓ ↑
tHD;DAT
SCL0
SDA0
0
3.45*2
0
0.9*3
µs
Data setup time SDA ↓ ↑ → SCL ↑
tSU;DAT
SCL0
SDA0
0.25*4
⎯
0.1*4
⎯
µs
Stop condition setup time
SCL ↑ → SDA ↑
tSU;STO
SCL0
SDA0
4.0
⎯
0.6
⎯
µs
tBUF
SCL0
SDA0
4.7
⎯
1.3
⎯
µs
SCL clock frequency
(Repeat) Start condition hold time
SDA ↓ → SCL ↓
Bus free time between stop
condition and start condition
R = 1.7 kΩ,
C = 50 pF*1
*1 : R, C : Pull-up resistor and load capacitor of the SCL and SDA lines.
*2 : The maximum tHD;DAT have only to be met if the device dose not stretch the “L” width (tLOW) of the SCL signal.
*3 : A fast-mode I2C-bus device can be used in a standard-mode I2C-bus system, but the requirement
tSU;DAT ≥ 250 ns must then be met.
*4 : Refer to “ • Note of SDA and SCL set-up time”.
• Note of SDA and SCL set-up time
SDA0
Input data set-up time
SCL0
6 tcp
Note : The rating of the input data set-up time in the device connected to the bus cannot be satisfied depending on
the load capacitance or pull-up resistor.
Be sure to adjust the pull-up resistor of SDA and SCL if the rating of the input data set-up time cannot be
satisfied.
52
MB95160M Series
tWAKEUP
SDA0
tLOW
tHD;DAT
tHIGH
tHD;STA
tBUF
SCL0
tHD;STA
tSU;DAT
tSU;STA
tSU;STO
53
MB95160M Series
(VCC = 5.0 V ± 10%, AVSS = VSS = 0.0 V, TA = −40 °C to + 85 °C)
Parameter
Sym- Pin
bol name
Conditions
Value*2
Min
Max
Unit
Remarks
SCL clock
“L” width
tLOW
SCL0
(2 + nm / 2) tMCLK − 20
⎯
ns
Master mode
SCL clock
“H” width
tHIGH
SCL0
(nm / 2) tMCLK − 20
(nm / 2 ) tMCLK + 20
ns
Master mode
Start condition
SCL0
tHD;STA
hold time
SDA0
(−1 + nm / 2) tMCLK − 20
(−1 + nm) tMCLK + 20
ns
Master mode
Maximum value is
applied when m,
n = 1, 8.
Otherwise, the
minimum value is
applied.
Stop condition
SCL0
tSU;STO
setup time
SDA0
(1 + nm / 2) tMCLK − 20
(1 + nm / 2) tMCLK + 20
ns
Master mode
Start condition
SCL0
tSU;STA
setup time
SDA0
(1 + nm / 2) tMCLK − 20
(1 + nm / 2) tMCLK + 20
ns
Master mode
SCL0
SDA0
(2 nm + 4) tMCLK − 20
⎯
ns
SCL0
SDA0
3 tMCLK − 20
⎯
ns
Master mode
ns
Master mode
When assuming
that “L” of SCL is
not extended, the
minimum value is
applied to first bit
of continuous
data.
Otherwise,
the maximum
value is applied.
Bus free time
between stop
condition and
start condition
tBUF
Data hold time tHD;DAT
R = 1.7 kΩ,
C = 50 pF*1
Data setup
time
Setup time
between
clearing
interrupt and
SCL rising
tSU;DAT
SCL0
SDA0
tSU;INT SCL0
(−2 + nm / 2) tMCLK − 20 (−1 + nm / 2) tMCLK + 20
(nm / 2) tMCLK − 20
(1 + nm / 2) tMCLK + 20
ns
Minimum value is
applied to interrupt
at 9th SCL↓.
Maximum value is
applied to interrupt
at 8th SCL↓.
SCL clock “L”
width
tLOW
SCL0
4 tMCLK − 20
⎯
ns
At reception
SCL clock “H”
width
tHIGH
SCL0
4 tMCLK − 20
⎯
ns
At reception
SCL0
Start condition
tHD;STA
SDA0
detection
2 tMCLK − 20
⎯
ns
Undetected when
1 tMCLK is used at
reception
(Continued)
54
MB95160M Series
(Continued)
Parameter
(VCC = 5.0 V ± 10%, AVSS = VSS = 0.0 V, TA = −40 °C to + 85 °C)
Sym- Pin
bol name
Conditions
Value*2
Min
Max
Unit
Remarks
Stop condition
detection
tSU;STO
SCL0
SDA0
2 tMCLK − 20
⎯
ns
Undetected when 1
tMCLK is used at
reception
Restart condition
detection condition
tSU;STA
SCL0
SDA0
2 tMCLK − 20
⎯
ns
Undetected when 1
tMCLK is used at
reception
Bus free time
tBUF
SCL0
SDA0
2 tMCLK − 20
⎯
ns
At reception
Data hold time
tHD;DAT
2 tMCLK − 20
⎯
ns
At slave transmission
mode
Data setup time
tSU;DAT
SCL0
SDA0 R = 1.7 kΩ,
1
SCL0 C = 50 pF*
tLOW − 3 tMCLK − 20
⎯
ns
At slave transmission
mode
Data hold time
tHD;DAT
SCL0
SDA0
0
⎯
ns
At reception
Data setup time
tSU;DAT
SCL0
SDA0
tMCLK − 20
⎯
ns
At reception
SDA↓→SCL↑
(at wakeup function)
tWAKE-
SCL0
SDA0
Oscillation
stabilization
wait time +
2 tMCLK − 20
⎯
ns
UP
SDA0
*1 : R, C : Pull-up resistor and load capacitor of the SCL and SDA lines.
*2 : •
•
•
•
Refer to “ (2) Source Clock/Machine Clock” for tMCLK.
m is CS4 bit and CS3 bit (bit 4 and bit 3) of I2C clock control register (ICCR) .
n is CS2 bit to CS0 bit (bit 2 to bit 0) of I2C clock control register (ICCR) .
Actual timing of I2C is determined by m and n values set by the machine clock (tMCLK) and CS4 to CS0 of
ICCR0 register.
• Standard-mode :
m and n can be set at the range : 0.9 MHz < tMCLK (machine clock) < 10 MHz.
Setting of m and n determines the machine clock that can be used below.
(m, n) = (1, 8)
: 0.9 MHz < tMCLK ≤ 1 MHz
(m, n) = (1, 22) , (5, 4) , (6, 4) , (7, 4) , (8, 4) : 0.9 MHz < tMCLK ≤ 2 MHz
(m, n) = (1, 38) , (5, 8) , (6, 8) , (7, 8) , (8, 8) : 0.9 MHz < tMCLK ≤ 4 MHz
(m, n) = (1, 98)
: 0.9 MHz < tMCLK ≤ 10 MHz
• Fast-mode :
m and n can be set at the range : 3.3 MHz < tMCLK (machine clock) < 10 MHz.
Setting of m and n determines the machine clock that can be used below.
(m, n) = (1, 8)
: 3.3 MHz < tMCLK ≤ 4 MHz
(m, n) = (1, 22) , (5, 4)
: 3.3 MHz < tMCLK ≤ 8 MHz
(m, n) = (6, 4)
: 3.3 MHz < tMCLK ≤ 10 MHz
55
MB95160M Series
(9) Low Voltage Detection
(Vss = 0.0 V, TA = −10 °C to + 85 °C)
Symbol
Parameter
Conditions
Value
Min
Typ
Max
Unit
Remarks
Release voltage
VDL+
2.52
2.70
2.88
V
At power-supply rise
Detection voltage
VDL-
2.42
2.60
2.78
V
At power-supply fall
Hysteresis width
VHYS
70
100
⎯
mV
Power-supply start voltage
Voff
⎯
⎯
2.3
V
Power-supply end voltage
Von
4.9
⎯
⎯
V
0.3
⎯
⎯
µs
Slope of power supply that reset
release signal generates
⎯
3000
⎯
µs
Slope of power supply that reset
release signal generates within
rating (VDL+)
300
⎯
⎯
µs
Slope of power supply that reset
detection signal generates
⎯
300
⎯
µs
Slope of power supply that reset
detection signal generates within
rating (VDL-)
Power-supply voltage
change time
(at power supply rise)
tr
⎯
Power-supply voltage
change time
(at power supply fall)
tf
Reset release delay time
td1
⎯
⎯
400
µs
Reset detection delay time
td2
⎯
⎯
30
µs
Current consumption
ILVD
⎯
38
50
µA
Current consumption of low
voltage detection circuit only
Vcc
Von
Voff
Time
Vcc
tr
tf
VDL+
VHYS
VDL-
Internal reset signal
Time
td2
56
td1
MB95160M Series
(10) Clock Supervisor Clock
(Vcc = 5.0 V ± 10%, Vss = 0.0 V, TA = −40 °C to + 85 °C)
Parameter
Symbol
Oscillation frequency
fOUT
Oscillation start time
twk
Conditions
⎯
Current consumption
ICSV
Value
Unit
Min
Typ
Max
50
100
200
kHz
⎯
⎯
10
µs
⎯
20
36
µA
Remarks
Current consumption of
built-in CR oscillator, at
100 kHz oscillation
57
MB95160M Series
5. A/D Converter
(1) A/D Converter Electrical Characteristics
(AVCC = VCC = 4.0 V to 5.5 V, AVSS = VSS = 0.0 V, TA = − 40 °C to + 85 °C)
Parameter
Sym- Condibol
tions
Unit
Min
Typ
Max
Resolution
⎯
⎯
10
bit
Total error
− 3.0
⎯
+ 3.0
LSB
− 2.5
⎯
+ 2.5
LSB
− 1.9
⎯
+ 1.9
LSB
Linearity error
⎯
Differential
linear error
Remarks
Zero
transition
voltage
VOT
AVSS − 1.5 LSB AVSS + 0.5 LSB AVSS + 2.5 LSB
V
Full-scale
transition
voltage
VFST
AVR − 3.5 LSB AVR − 1.5 LSB AVR + 0.5 LSB
V
0.9
⎯
16500
µs
4.5 V ≤ AVcc ≤ 5.5 V
1.8
⎯
16500
µs
4.0 V ≤ AVcc < 4.5 V
0.6
⎯
∞
µs
4.5 V ≤ AVcc ≤ 5.5 V,
At external
impedance < 5.4 kΩ
1.2
⎯
∞
µs
4.0 V ≤ AVcc < 4.5 V,
At external
impedance < 2.4 kΩ
Compare time
⎯
⎯
Sampling time
58
Value
⎯
Analog input
current
IAIN
− 0.3
⎯
+ 0.3
µA
Analog input
voltage
VAIN
AVSS
⎯
AVR
V
Reference
voltage
⎯
AVSS + 4.0
⎯
AVCC
V
AVR pin
Reference
voltage supply
current
IR
⎯
600
900
µA
AVR pin,
during A/D operation
IRH
⎯
⎯
5
µA
AVR pin,
at stop mode
MB95160M Series
(2) Notes on Using A/D Converter
• About the external impedance of analog input and its sampling time
A/D converter with sample and hold circuit. If the external impedance is too high to keep sufficient sampling
time, the analog voltage charged to the internal sample and hold capacitor is insufficient, adversely affecting A/
D conversion precision. Therefore, to satisfy the A/D conversion precision standard, consider the relationship
between the external impedance and minimum sampling time and either adjust the register value and operating
frequency or decrease the external impedance so that the sampling time is longer than the minimum value. Also,
if the sampling time cannot be sufficient, connect a capacitor of about 0.1 µF to the analog input pin.
• Analog input equivalent circuit
R
Analog input
Comparator
C
During sampling : ON
R
2.0 kΩ (Max)
8.2 kΩ (Max)
4.5 V ≤ VCC ≤ 5.5 V
4.0 V ≤ VCC < 4.5 V
C
16 pF (Max)
16 pF (Max)
Note : The values are reference values.
• The relationship between external impedance and minimum sampling time
(External impedance = 0 kΩ to 20 kΩ)
100
90
80
70
60
50
40
30
20
10
0
VCC ≥ 4.5 V
VCC ≥ 4.0 V
0
2
4
6
8
10
12
14
External impedance [kΩ]
External impedance [kΩ]
(External impedance = 0 kΩ to 100 kΩ)
20
18
16
14
12
10
8
6
4
2
0
VCC ≥ 4.5 V
VCC ≥ 4.0 V
0
Minimum sampling time [µs]
1
2
3
4
Minimum sampling time [µs]
• About errors
As |VCC − VSS| becomes smaller, values of relative errors grow larger.
59
MB95160M Series
(3) Definition of A/D Converter Terms
• Resolution
The level of analog variation that can be distinguished by the A/D converter.
When the number of bits is 10, analog voltage can be divided into 210 = 1024.
• Linearity error (unit : LSB)
The deviation between the value along a straight line connecting the zero transition point
(“00 0000 0000” ← → “00 0000 0001”) of a device and the full-scale transition point
(“11 1111 1111” ← → “11 1111 1110”) compared with the actual conversion values obtained.
• Differential linear error (Unit : LSB)
Deviation of input voltage, which is required for changing output code by 1 LSB, from an ideal value.
• Total error (unit: LSB)
Difference between actual and theoretical values, caused by a zero transition error, full-scale transition error,
linearity error, quantum error, and noise.
Ideal I/O characteristics
Total error
VFST
3FFH
3FFH
3FEH
1.5 LSB
3FDH
004H
003H
002H
VOT
Digital output
Digital output
3FEH
3FDH
Actual conversion
characteristic
{1 LSB × (N − 1) + 0.5 LSB}
004H
003H
002H
1 LSB
VNT
Actual conversion
characteristic
Ideal characteristics
001H
001H
0.5 LSB
VSS
Analog input
1 LSB =
VCC − Vss
1024
(V)
VCC
VSS
VCC
Analog input
Total error of VNT − {1 LSB × (N − 1) + 0.5 LSB}
=
[LSB]
digital output N
1 LSB
N : A/D converter digital output value
VNT : A voltage at which digital output transits from (N − 1) H to NH
(Continued)
60
MB95160M Series
(Continued)
Full-scale transition error
Zero transition error
004H
Ideal characteristics
3FFH
Digital output
Digital output
Actual conversion
characteristic
003H
Ideal
characteristics
002H
Actual conversion
characteristic
Actual conversion
characteristic
3FEH
VFST
(measurement
value)
3FDH
Actual conversion
characteristic
001H
3FCH
VOT (measurement value)
VSS
VCC
VSS
Analog input
Differential linear error
Linearity error
Ideal characteristics
Actual conversion
characteristic
3FFH
(N+1)H
3FEH
{1 LSB × N + VOT}
3FDH
VFST
(measurement
value)
VNT
004H
Actual conversion
characteristic
003H
Digital output
Digital output
VCC
Analog input
Actual conversion
characteristic
NH
(N-1)H
VNT
Actual conversion
characteristic
Ideal characteristics
002H
(N-2)H
001H
V (N+1)T
VOT (measurement value)
VSS
Analog input
Linearity error in = VNT − {1 LSB × N + VOT}
1 LSB
digital output N
VCC
VSS
Analog input
Differential linear error =
in digital output N
V (N + 1) T − VNT
1 LSB
VCC
−1
N : A/D converter digital output value
VNT : A voltage at which digital output transits from (N − 1) H to NH
VOT (Ideal value) = VSS + 0.5 LSB [V]
VFST (Ideal value) = VCC − 1.5 LSB [V]
61
MB95160M Series
6. Flash Memory Program/Erase Characteristics
Parameter
Value
Conditions
Unit
Remarks
15*2
s
Excludes 00H programming
prior erasure.
32
3600
µs
Excludes system-level
overhead.
10000
⎯
⎯
cycle
Power supply voltage at
erase/program
4.5
⎯
5.5
V
Flash memory data retention
time
20*3
⎯
⎯
year
Min
Typ
Max
Chip erase time
⎯
1*1
Byte programming time
⎯
Erase/program cycle
⎯
Average TA = + 85 °C
*1 : TA = + 25 °C, VCC = 5.0 V, 10000 cycles
*2 : TA = + 85 °C, VCC = 4.5 V, 10000 cycles
*3 : This value comes from the technology qualification (using Arrhenius equation to translate high temperature
measurements into normalized value at +85 °C) .
62
MB95160M Series
■ EXAMPLE CHARACTERISTICS
• Power supply current temperature
ICC − VCC
TA = + 25 °C, FMP = 2, 4, 8, 10, 16 MHz (divided by 2)
Main clock mode, at external clock operating
ICC − TA
VCC = 5.5 V, FMP = 10, 16 MHz (divided by 2)
Main clock mode, at external clock operating
20
20
15
15
FMP = 16 MHz
10
ICC [mA]
ICC [mA]
FMP = 16 MHz
FMP = 10 MHz
10
FMP = 10 MHz
FMP = 8 MHz
5
5
FMP = 4 MHz
FMP = 2 MHz
0
0
2
3
4
5
6
-50
7
0
VCC [V]
20
20
15
15
10
FMP =16 MHz
5
5
6
FMP = 16 MHz
FMP = 10 MHz
0
-50
0
4
7
0
VCC [V]
+50
+100
+150
TA [°C]
ICCMPLL − VCC
TA = + 25 °C, FMP = 2, 4, 8, 10, 16 MHz
(Main PLL multiplied by 2.5)
Main PLL mode, at external clock operating
ICCMPLL − TA
VCC = 5.5 V, FMP = 10, 16 MHz (Main PLL multiplied by 2.5)
Main PLL mode, at external clock operating
20
20
15
15
FMP = 16 MHz
ICCMPLL [mA]
ICCMPLL [mA]
+150
10
5
FMP =10 MHz
FMP = 8 MHz
FMP = 4 MHz
FMP = 2 MHz
3
+100
ICCS − TA
VCC = 5.5 V, FMP = 10, 16 MHz (divided by 2)
Main sleep mode, at external clock operating
ICCS [mA]
ICCS [mA]
ICCS − VCC
TA = + 25 °C, FMP = 2, 4, 8, 10, 16 MHz (divided by 2)
Main sleep mode, at external clock operating
2
+50
TA [°C]
10
FMP = 10 MHz
FMP = 8 MHz
FMP = 16 MHz
10
FMP = 10 MHz
5
5
FMP = 4 MHz
FMP = 2 MHz
0
2
3
4
5
VCC [V]
6
7
0
-50
0
+50
+100
+150
TA [°C]
(Continued)
63
MB95160M Series
ICCL − TA
VCC = 5.5 V, FMPL = 16 kHz (divided by 2)
Sub clock mode, at external clock operating
100
100
75
75
ICCL [µA]
ICCL [µA]
ICCL − VCC
TA = + 25 °C, FMPL = 16 kHz (divided by 2)
Sub clock mode, at external clock operating
50
25
50
25
0
2
3
4
5
6
0
7
−50
0
VCC [V]
100
100
75
75
50
25
+150
50
25
0
2
3
4
5
6
0
7
−50
0
VCC [V]
ICCT − VCC
TA = + 25 °C, FMPL = 16 kHz (divided by 2)
Clock mode, at external clock operating
+50
TA [°C]
+100
+150
ICCT − TA
VCC = 5.5 V, FMPL = 16 kHz (divided by 2)
Clock mode, at external clock operating
100
100
75
75
ICCT [µA]
ICCT [µA]
+100
ICCLS − TA
VCC = 5.5 V, FMPL = 16 kHz (divided by 2)
Sub sleep mode, at external clock operating
ICCLS [µA]
ICCLS [µA]
ICCLS − VCC
TA = + 25 °C, FMPL = 16 kHz (divided by 2)
Sub sleep mode, at external clock operating
+50
TA [°C]
50
25
50
25
0
2
3
4
5
VCC [V]
6
7
0
−50
0
+50
TA [°C]
+100
+150
(Continued)
64
MB95160M Series
ICCSPLL − TA
VCC = 5.5 V, FMPL = 128 kHz (Main PLL multiplied by 4)
Sub PLL mode, at external clock operating
200
200
175
175
150
150
ICCSPLL [µA]
ICCSPLL [µA]
ICCSPLL − VCC
TA = + 25 °C, FMPL = 128 kHz (Main PLL multiplied by 4)
Sub PLL mode, at external clock operating
125
100
75
125
100
75
50
50
25
25
0
2
3
4
5
6
0
7
−50
0
VCC [V]
2.0
2.0
1.5
1.5
1.0
FMP = 10 MHz
FMP = 8 MHz
FMP = 4 MHz
FMP = 2 MHz
3
4
5
6
1.0
FMP = 10 MHz
0.5
0.0
2
0.0
−50
7
0
VCC [V]
ICCH − VCC
TA = + 25 °C, FMPL = (stop)
Sub stop mode, at external clock stopping
+50
TA [°C]
+100
+150
ICCH − TA
VCC = 5.5 V, FMPL = (stop)
Sub stop mode, at external clock stopping
20
20
15
15
ICCH [µA]
ICCH [µA]
+150
FMP = 16 MHz
FMP = 16 MHz
0.5
+100
ICTS − TA
VCC = 5.5 V, FMP = 10, 16 MHz (divided by 2)
Time-base timer mode, at external clock operating
ICTS [mA]
ICTS [mA]
ICTS − VCC
TA = + 25 °C, FMP = 2, 4, 8, 10, 16 MHz (divided by 2)
Time-base timer mode, at external clock operating
+50
TA [°C]
10
5
10
5
0
2
3
4
5
VCC [V]
6
7
0
−50
0
+50
TA [°C]
+100
+150
(Continued)
65
MB95160M Series
IA − AVCC
TA = + 25 °C, FMP = 16 MHz (divided by 2)
Main clock mode, at external clock operating
IA − TA
VCC = 5.5 V, FMP = 16 MHz (divided by 2)
Main clock mode, at external clock operating
4
4
3
3
IA [mA]
IA [mA]
(Continued)
2
1
2
1
0
2
3
4
5
6
0
7
−50
0
+100
+150
IR − TA
VCC = 5.5 V, FMP = 16 MHz (divided by 2)
Main clock mode, at external clock operating
4
4
3
3
2
1
2
1
0
2
3
4
5
AVCC [V]
66
+50
TA [°C]
IR − AVCC
TA = + 25 °C, FMP = 16 MHz (divided by 2)
Main clock mode, at external clock operating
IR [mA]
IR [mA]
AVCC [V]
6
7
0
−50
0
+50
TA [°C]
+100
+150
MB95160M Series
• Input voltage
VIH1 − VCC and VIL − VCC
TA = + 25 °C
VIHS1 − VCC and VILS − VCC
TA = + 25 °C
5
5
4
4
VIHS1
VIHS1 / VILS [V]
VIH1 / VIL [V]
VIH1
3
VIL
2
1
3
VILS
2
1
0
0
2
3
4
5
6
7
2
3
4
VCC [V]
5
6
7
VCC [V]
VIH2 − VCC and VIL − VCC
TA = + 25 °C
VIHS2 − VCC and VILS − VCC
TA = + 25 °C
5
5
4
4
VIHS2 / VILS [V]
VIH2 / VIL [V]
VIHS2
VIH2
3
VIL
2
3
VILS
2
1
1
0
0
2
3
4
5
6
2
7
3
4
VCC [V]
5
6
7
VCC [V]
VIHA − VCC and VILA − VCC
TA = + 25 °C
VIHM − VCC and VILM − VCC
TA = + 25 °C
5
5
VIHA
4
4
VIHM / VILM [V]
VIHA / VILA [V]
VILA
3
2
1
3
VIHM
2
VILM
1
0
0
2
3
4
5
VCC [V]
6
7
2
3
4
5
6
7
VCC [V]
67
MB95160M Series
• Output voltage
3.5 V
3.3 V
3V
1.0
2.7 V
2.5 V
VOH1 − IOH
TA = + 25 °C
VCC = 4 V
VCC = 4.5 V
VCC = 5.0 V
VCC = 5.5 V
VCC - VOH1 [V]
0.8
VCC = 2.45 V
0.6
0.4
0.2
0.0
0
-2
-4
-6
IOH [mA]
-8
-10
3V
2.45 V
VOL2 − IOL
TA = + 25 °C
2.7 V
VOL1 − IOL
TA = + 25 °C
1.0
VCC = 3.3 V
1.0
VCC = 2.5 V
VCC = 3.5 V
VCC = 2.5 V
VCC = 4.0 V
VCC = 4.5 V
VCC = 5.0 V
VCC = 5.5 V
0.6
VCC = 2.45 V
0.4
0.8
VCC = 2.7 V
VOL2 [V]
VOL1 [V]
0.8
0.6
VCC = 3.0 V
VCC = 3.3 V
VCC = 3.5 V
VCC = 4.0 V
VCC = 5.0 V
VCC = 2.5 V
0.4
0.2
0.2
0.0
0.0
0.0
0
2
4
6
8
10
2.0
IOL [mA]
4.0
6.0
IOL [mA]
• Pull-up
RPULL − VCC
TA = + 25 °C
250
RPULL [kΩ]
200
150
100
50
0
2
68
3
4
VCC [V]
5
6
8.0
10.0
MB95160M Series
■ MASK OPTION
No.
Part number
MB95F168M/F168N/F168J
MB95FV100D-103
Specifying procedure
Setting disabled
Setting disabled
1
Clock mode select*
• Single-system clock mode
• Dual-system clock mode
Dual-system clock mode
Changing by the switch on MCU board
2
Low voltage detection reset*
• With low voltage detection reset
• Without low voltage detection
reset
Specified by part number
Changing by the switch on MCU board
3
Clock supervisor*
• With clock supervisor
• Without clock supervisor
Specified by part number
Changing by the switch on MCU board
4
Reset output*
• With reset output
• Without reset output
Specified by part number
MCU board switch sets as follows;
• With clock supervisor:
Without reset output
• Without clock supervisor:
With reset output
5
Oscillation stabilization wait time
Fixed to oscillation stabilization Fixed to oscillation stabilization wait
wait time of (214 − 2) /FCH
time of (214 − 2) /FCH
* : Refer to table below about clock mode select, low voltage detection reset, clock supervisor select and reset output.
Part number
Clock mode select
MB95F168M
MB95F168N
Dual-system
MB95F168J
Single-system
MB95FV100D-103
Dual-system
Low voltage detection reset Clock supervisor Reset output
No
No
Yes
Yes
No
Yes
Yes
Yes
No
No
No
Yes
Yes
No
Yes
Yes
Yes
No
No
No
Yes
Yes
No
Yes
Yes
Yes
No
69
MB95160M Series
■ ORDERING INFORMATION
Part number
MB95F168MPMC
MB95F168NPMC
MB95F168JPMC
64-pin plastic LQFP
(FPT-64P-M23)
MB95F168MPMC1
MB95F168NPMC1
MB95F168JPMC1
64-pin plastic LQFP
(FPT-64P-M024)
MB2146-303A
(MB95FV100D-103PBT)
70
Package
MCU board
224-pin plastic PFBGA
(BGA-224P-M08)
(
)
MB95160M Series
■ PACKAGE DIMENSIONS
64-pin plastic LQFP
Lead pitch
0.65 mm
Package width ×
package length
12.0 × 12.0 mm
Lead shape
Gullwing
Sealing method
Plastic mold
Mounting height
1.70 mm MAX
Code
(Reference)
P-LFQFP64-12×12-0.65
(FPT-64P-M23)
64-pin plastic LQFP
(FPT-64P-M23)
Note 1) * : These dimensions do not include resin protrusion.
Note 2) Pins width and pins thickness include plating thickness.
Note 3) Pins width do not include tie bar cutting remainder.
14.00±0.20(.551±.008)SQ
*12.00±0.10(.472±.004)SQ
48
0.145±0.055
(.0057±.0022)
33
32
49
0.10(.004)
Details of "A" part
+0.20
1.50 –0.10
+.008
(Mounting height)
.059 –.004
0.25(.010)
INDEX
0~8˚
17
64
1
0.65(.026)
C
"A"
16
0.32±0.05
(.013±.002)
0.13(.005)
0.50±0.20
(.020±.008)
0.60±0.15
(.024±.006)
0.10±0.10
(.004±.004)
(Stand off)
M
2003 FUJITSU LIMITED F64034S-c-1-1
Dimensions in mm (inches).
Note: The values in parentheses are reference values
Please confirm the latest Package dimension by following URL.
http://edevice.fujitsu.com/fj/DATASHEET/ef-ovpklv.html
(Continued)
71
MB95160M Series
(Continued)
64-pin plastic LQFP
Lead pitch
0.50 mm
Package width ×
package length
10.0 × 10.0 mm
Lead shape
Gullwing
Sealing method
Plastic mold
Mounting height
1.70 mm MAX
Weight
0.32g
Code
(Reference)
P-LFQFP64-10×10-0.50
(FPT-64P-M24)
64-pin plastic LQFP
(FPT-64P-M24)
Note 1) * : These dimensions do not include resin protrusion.
Note 2) Pins width and pins thickness include plating thickness.
Note 3) Pins width do not include tie bar cutting remainder.
12.00±0.20(.472±.008)SQ
* 10.00±0.10(.394±.004)SQ
48
0.145±0.055
(.006±.002)
33
32
49
Details of "A" part
0.08(.003)
+0.20
1.50 –0.10
+.008
.059 –.004
INDEX
0˚~8˚
17
64
(Mounting height)
0.10±0.10
(.004±.004)
(Stand off)
"A"
LEAD No.
1
16
0.50(.020)
C
0.20±0.05
(.008±.002)
0.08(.003)
M
2005 FUJITSU LIMITED F64036S-c-1-1
Please confirm the latest Package dimension by following URL.
http://edevice.fujitsu.com/fj/DATASHEET/ef-ovpklv.html
72
0.50±0.20
(.020±.008)
0.60±0.15
(.024±.006)
0.25(.010)
Dimensions in mm (inches).
Note: The values in parentheses are reference values
MB95160M Series
■ MAIN CHANGES (The Main Changes from the First Edition to This Edition)
Page
Section
⎯
⎯
Change Results
Preliminary Data Sheet → Data Sheet
22
■ I/O MAP
Changed as follows for R/W of Reset factor register
R → R/W
29
■ ELECTRICAL CHARACTERISTICS
1. Absolute Maximum Ratings
The Min value in the row of “Operating temperature” is
changed as follows;
− 40 → − 10
31
■ ELECTRICAL CHARACTERISTICS
The Min value in the row of “Operating temperature” is
2. Recommended Operating Conditions changed as follows;
− 40 → − 10
36
4. AC Characteristics (1) Clock Timing
Added “Main PLL multiplied by 4” in the Clock frequency
38
(2) Source Clock/Machine Clock
• Changed in the remarks of source clock cycle time
(when using main clock)
Min : FCH = 16.25 MHz, PLL multiplied by 1 →
Min : FCH = 8.125 MHz, PLL multiplied by 2
• Changed the footnote of *1;
PLL multiplication of main clock (select from 1, 2, 2.5
multiplication) → PLL multiplication of main clock
(select from 1, 2, 2.5, 4 multiplication)
39
• Added “ × 4” in the Main PLL of “• Outline of clock
generation block”
41
Changed the figure of “• Main PLL operation frequency”
52 to 55
(8) I2C Timing
Added the characteristics
63 to 68
■ EXAMPLE CHARACTERISTICS
Added the ■ EXAMPLE CHARACTERISTICS
The vertical lines marked in the left side of the page show the changes.
73
MB95160M Series
The information for microcontroller supports is shown in the following homepage.
http://www.fujitsu.com/global/services/microelectronics/product/micom/support/index.html
FUJITSU LIMITED
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with FUJITSU sales
representatives before ordering.
The information, such as descriptions of function and application
circuit examples, in this document are presented solely for the
purpose of reference to show examples of operations and uses of
Fujitsu semiconductor device; Fujitsu does not warrant proper
operation of the device with respect to use based on such
information. When you develop equipment incorporating the
device based on such information, you must assume any
responsibility arising out of such use of the information. Fujitsu
assumes no liability for any damages whatsoever arising out of
the use of the information.
Any information in this document, including descriptions of
function and schematic diagrams, shall not be construed as license
of the use or exercise of any intellectual property right, such as
patent right or copyright, or any other right of Fujitsu or any third
party or does Fujitsu warrant non-infringement of any third-party’s
intellectual property right or other right by using such information.
Fujitsu assumes no liability for any infringement of the intellectual
property rights or other rights of third parties which would result
from the use of information contained herein.
The products described in this document are designed, developed
and manufactured as contemplated for general use, including
without limitation, ordinary industrial use, general office use,
personal use, and household use, but are not designed, developed
and manufactured as contemplated (1) for use accompanying fatal
risks or dangers that, unless extremely high safety is secured, could
have a serious effect to the public, and could lead directly to death,
personal injury, severe physical damage or other loss (i.e., nuclear
reaction control in nuclear facility, aircraft flight control, air traffic
control, mass transport control, medical life support system, missile
launch control in weapon system), or (2) for use requiring
extremely high reliability (i.e., submersible repeater and artificial
satellite).
Please note that Fujitsu will not be liable against you and/or any
third party for any claims or damages arising in connection with
above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You
must protect against injury, damage or loss from such failures by
incorporating safety design measures into your facility and
equipment such as redundancy, fire protection, and prevention of
over-current levels and other abnormal operating conditions.
If any products described in this document represent goods or
technologies subject to certain restrictions on export under the
Foreign Exchange and Foreign Trade Law of Japan, the prior
authorization by Japanese government will be required for export
of those products from Japan.
The company names and brand names herein are the trademarks or
registered trademarks of their respective owners.
Edited
Business Promotion Dept.
F0709