GENLINX ™ GS9008A Cable Driver with Two Adjustable Outputs DATA SHEET DESCRIPTION • two output pairs, adjustable from 0 to 1100mVp-p into 75 Ω loads The GENLINX™ GS9008A is a bipolar integrated circuit designed to drive two 75 Ω co-axial cables at data rates exceeding 400Mb/s. It directly interfaces with other GENLINX™ devices and can also be used as a general purpose high speed cable driver. • nominal 600 ps rise and fall times • accepts SMPTE and standard ECL input levels • operates from a single +5 or -5 volt supply • on-chip DC restoration for low jitter • 170mW power dissipation • Pb-free and Green APPLICATIONS • SMPTE 259M Serial Digital Systems (4:2:2 & 4ƒsc) • Other Serial Digital Video Interfaces — 360Mb/s • General purpose high speed driver applications PIN CONNECTIONS OUTPUT 1 1 OUTPUT 1 2 8 VCC 7 INPUT GS9008A VSET 3 6 INPUT VREF 4 5 VEE While there are no plans to discontinue the GS9008A, Gennum has developed a successor product with improved features and performance called the GS9028. The GS9028 is recommended for new designs. The differential inputs are AC-coupled and internally DCrestored which allows correct passage of pathological check codes associated with the serial digital standards. Even though the inputs are AC coupled, static protection diodes at each input restrict the DC differential so that if the driving source uses the opposite polarity power supply, external DC blocking capacitors must be used. Correctly terminated output signal levels are adjustable from as low as 0mV to as high as 1100mV with little change in other performance parameters. Performance is guaranteed for output levels between 600mV and 1000mV. The gain of the output stages is varied by adjusting the VSET voltage with respect to an internal band gap reference voltage VREF. The GS9008A is packaged in an 8 pin SOIC, and operates from a single +5 or -5 volt supply consuming typically only 170mW of power. ORDERING INFORMATION PART NUMBER PACKAGE TYPE TEMPERATURE RANGE Pb-FREE AND GREEN GS9008ACKA 8 Pin SOIC 0° to 70°C No GS9008ACKAE3 8 Pin SOIC 0° to 70°C Yes FUNCTIONAL BLOCK DIAGRAM GS9008A VSET INPUT INPUT VREF VCC (GND) GAIN CONTROL INPUT BUFFER & DC RESTORE OUTPUT DRIVER OUTPUT 1 OUTPUT 1 BAND-GAP REFERENCE GND (VEE) Revision Date: June 2004 Document No. 29781 - 1 GENNUM CORPORATION P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 E-mail: [email protected] www.gennum.com NOT RECOMMENDED FOR NEW DESIGNS • interfaces with GENLINX™ GS9002, GS9004A, GS9005A and GS9015A GS9008A KEY FEATURES ABSOLUTE MAXIMUM RATINGS PARAMETER VALUE Supply Voltage (VS) 5.5V Input Voltage Range (any input) VS -0.5V Power Dissipation 300mW GS9008A 0°C ≤ TA ≤ 70°C Operating Temperature Range -65°C ≤ TS ≤ 150°C Storage Temperature Range Lead Temperature (soldering, 10 sec) 260°C GS9008A CABLE DRIVER — DC ELECTRICAL CHARACTERISTICS Conditions: VS = 5V, TA = 0°C to 70°C, RL= 150 Ω to GND and 144 Ω AC coupled unless otherwise shown SYMBOL CONDITIONS MIN TYP MAX UNITS 4.5 5.0 5.5 volts - 170 190 mW - 62 67 mA Supply Voltage VS Power Consumption PD Supply Current ΙS1 4 x150Ω Loads DC 1% Accuracy, TA= 25°C VSET = (0.667) VREF Supply Current ΙS2 DC No Loads, TA= 25°C - 16 20 mA 10 kΩ to ground - 1.2 - volts Reference Voltage VREF NOTES GS9008A CABLE DRIVER — AC ELECTRICAL CHARACTERISTICS Conditions: VS = 5V, TA = 0°C to 70°C, RL= 150 Ω to GND and 144 Ω AC coupled unless otherwise shown PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS NOTES Input Signal Amplitude VIN 700 800 1000 mVp-p Input Signal Rise/Fall Times tR,tF - - 750 ps Output Amplitudes across 75 Ω Load (See Note 1) VOUT VSET = (0.5) VREF 540 600 660 mVp-p Note 1 & 2 VSET = (0.667) VREF 720 800 880 mVp-p Note 1 & 2 VSET = (0.833) VREF 900 1000 1100 mVp-p Note 1 & 2 VSET = (0.5) VREF - 25 100 ppm/°C VSET = (0.667) VREF - -12 80 ppm/°C VSET = (0.833) VREF - -45 80 ppm/°C VSET = (0.5) VREF 400 630 800 ps VSET = (0.667) VREF 400 575 800 ps VSET = (0.833) VREF 400 530 800 ps tR= tF = 600 ps - 0 - % at 270Mb/s - - ±25 ps - 1 - ns Output Amplitude Temperature Coefficient (See Note 2) Output Rise/Fall Times (20% to 80%) TC tR,tF Output Overshoot Jitter tJ Propagation Delay tP See Figure 3 1. VOUT is measured across a correctly terminated load, back matched to the device. The peak to peak voltage of the device itself is 2 x VOUT. 2. VOUT is proportional to VSET and VSET may be an external low impedance, high stability supply. In this case the amplitude temperature coefficient will not be guaranteed. 2 of 4 GENNUM CORPORATION 29781 - 1 NOT RECOMMENDED FOR NEW DESIGNS PARAMETER INPUT/OUTPUT CIRCUITS VCC VCC VCC VCC 400 VREF1 0.5p GS9008A SERIAL INPUTS 400 VOUT 400 VREF1 + VREF2 VCC NOT RECOMMENDED FOR NEW DESIGNS Figure 1 VOUT Input Circuit (Pins 6 and 7) Figure 2 Output Circuit (Pins 1 and 2) 0.1 +5V OUTPUT LEVEL ADJUST 10k 1.8p 5 4 INPUT SIGNAL 6 3 INPUT SIGNAL 7 GS9008A 1.0 68 2 1.0 68 OUTPUT -1 (75Ω) 1 8 OUTPUT -1 (75Ω) 1.8p + 10 150 0.1 150 All resistors in ohms, all capacitors in microfarads unless otherwise stated. Figure 3 -5V Typical Application Circuit +5V 7 0.1µF ECL DRIVER GS9008A 6 0.1µF -2V All resistors in ohms, all capacitors in microfarads unless otherwise stated. Figure 4 Split Supply Interfacing 3 of 4 GENNUM CORPORATION 29781 - 1 REVISION HISTORY VERSION ECR DATE 0 132427 October 2003 1 134030 June 2004 CHANGES AND/OR MODIFICATIONS New Document Added lead-free and green information. GS9008A NOT RECOMMENDED FOR NEW DESIGNS DOCUMENT IDENTIFICATION CAUTION PRELIMINARY DATA SHEET The product is in a preproduction phase and specifications are subject to change without notice. ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN PACKAGES OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION GENNUM CORPORATION GENNUM JAPAN CORPORATION Shinjuku Green Tower Building 27F, 6-14-1, Nishi Shinjuku, Shinjuku-ku, Tokyo, 160-0023 Japan Tel. +81 (03) 3349-5501, Fax. +81 (03) 3349-5505 MAILING ADDRESS: P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 GENNUM UK LIMITED 25 Long Garden Walk, Farnham, Surrey, England GU9 7HX Tel. +44 (0)1252 747 000 Fax +44 (0)1252 726 523 SHIPPING ADDRESS: 970 Fraser Drive, Burlington, Ontario, Canada L7L 5P5 Gennum Corporation assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement. © Copyright October 2003 Gennum Corporation. All rights reserved. Printed in Canada. 4 of 4 29781 - 1