HANBit HMD32M32M16G 128Mbyte (32Mx32) 72-pin Fast Page Mode 4K Ref. SIMM Design 5V Part No. HMD32M32M16G GENERAL DESCRIPTION The HMD32M32M16G is a 32M x 32bit dynamic RAM high-density memory module. The module consists of sixteen CMOS 16M x 4bit DRAMs in 32-pin TSOPII packages mounted on a 72-pin, double-sided, FR-4-printed circuit board. A 0.1uF decoupling capacitor is mounted on the printed circuit board for each DRAM components. The module is a Single In-line Memory Module with edge connections and is intended for mounting in to 72-pin edge connector sockets. All module components may be powered from a single 5V DC power supply and all inputs and outputs are TTL-compatible. PIN ASSIGNMENT FEATURES PIN wPart Identification HMD32M32M16G-- 4K Cycles/64ms Ref. Gold w Access times : 50, 60ns w High-density 128MByte design w Single + 5V ±0.5V power supply w JEDEC standard pinout w Fast Page mode operation w TTL compatible inputs and outputs w FR4-PCB design OPTIONS MARKING w Timing 50ns access 60ns access -5 -6 w Packages 72-pin SIMM M PERFORMANCE RANGE SPEED tRAC tCAC tRC SYMBOL PIN SYMBOL PIN SYMBOL 1 Vss 25 DQ22 49 DQ8 2 DQ0 26 DQ7 50 DQ24 3 DQ16 27 DQ23 51 DQ9 4 DQ1 28 A7 52 DQ25 5 DQ17 29 A11 53 DQ10 6 DQ2 30 Vcc 54 DQ26 7 DQ18 31 A8 55 DQ11 8 DQ3 32 A9 56 DQ27 9 DQ19 33 /RAS3 57 DQ12 10 Vcc 34 /RAS2 58 DQ28 11 NC 35 NC 59 Vcc 12 A0 36 NC 60 DQ29 13 A1 37 NC 61 DQ13 14 A2 38 NC 62 DQ30 15 A3 39 Vss 63 DQ14 16 A4 40 /CAS0 64 DQ31 17 A5 41 /CAS2 65 DQ15 18 A6 42 /CAS3 66 NC A10 43 /CAS1 67 PD1 -5 50ns 13ns 90ns 19 -6 60ns 15ns 110ns 20 DQ4 44 /RAS0 68 PD2 21 DQ20 45 /RAS1 69 PD3 22 DQ5 46 NC 70 PD4 23 DQ21 47 /WE 71 NC 24 DQ6 48 NC 72 Vss PRESENCE DETECT PINS Pin 50ns 60ns PD1 NC NC PD2 Vss Vss PD3 Vss NC PD4 Vss NC URL:www.hbe.co.kr REV.1.0 (August.2002) 72 PIN -1- SIMM TOP VIEW HANBit Electronics Co.,Ltd. HANBit HMD32M32M16G FUNCTIONAL BLOCK DIAGRAM /CAS0 /RAS0 /CAS /RAS /OE U1 /WE A0 -A11 /CAS /RAS /OE U2 /WE /CAS1 /CAS /RAS /OE A0 -A11 U3 /WE A0 -A11 DQ1 DQ2 DQ3 DQ0-DQ3 DQ1 DQ2 DQ3 DQ4 U5 /WE /CAS /RAS /OE A0-A11 /CAS0 /RAS1 DQ4 DQ1 DQ2 DQ3 DQ4-DQ7 DQ1 DQ2 DQ3 DQ4 U6 /WE /CAS /RAS /OE A0 -A11 DQ4 DQ1 DQ2 DQ3 DQ4 DQ8-DQ11 DQ1 DQ2 DQ3 DQ4 /CAS /RAS /OE A0 -A11 U7 /WE /CAS1 DQ12-DQ15 /CAS /RAS /OE U4 /WE A0 -A11 DQ1 DQ2 DQ3 DQ1 DQ2 DQ3 DQ4 U8 /WE /CAS /RAS /OE A0 -A11 DQ4 DQ16-DQ19 /CAS2 /RAS2 /CAS /RAS /OE U9 /WE A0 -A11 DQ1 DQ2 DQ3 DQ1 DQ2 DQ3 DQ4 U13 /WE /CAS /RAS /OE A0 -A11 /CAS2 /RAS3 DQ4 DQ20-DQ23 /CAS /RAS /OE U10 /WE A0 -A11 DQ1 DQ2 DQ3 DQ1 DQ2 DQ3 DQ4 U14 /WE /CAS /RAS /OE A0 -A11 DQ4 DQ24-DQ27 /CAS3 /CAS /RAS /OE U11 /WE A0 -A11 DQ1 DQ2 DQ3 DQ1 DQ2 DQ3 DQ4 U15 /WE /CAS /RAS /OE A0 -A11 /CAS3 DQ4 DQ28-DQ31 /CAS /RAS /OE U12 /WE A0 -A11 DQ1 DQ2 DQ3 DQ1 DQ2 DQ3 DQ4 /CAS /RAS /OE A0 -A11 U16 /WE DQ4 /WE A0-A11 Vcc Vss URL:www.hbe.co.kr REV.1.0 (August.2002) -2- 0.1uF Capacitor for each DRAM To all DRAMs HANBit Electronics Co.,Ltd. HANBit HMD32M32M16G ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL RATING VIN ,OUT -1V to 7.0V Voltage on Vcc Supply Relative to Vss Vcc -1V to 7.0V Power Dissipation PD 16W TSTG -55oC to 150oC Voltage on Any Pin Relative to Vss Storage Temperature Short Circuit Output Current IOS 50mA w Permanent device damage may occur if " Absolute Maximum Ratings" are exceeded. Functional operation should be restricted to the conditions as detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. RECOMMENDED DC OPERATING CONDITIONS ( Voltage reference to VSS, TA=0 to 70 o C ) PARAMETER SYMBOL MIN TYP. MAX UNIT Supply Voltage Vcc 4.5 5.0 5.5 V Ground Vss 0 0 0 V Input High Voltage VIH 2.4 - Vcc+1 V Input Low Voltage VIL -1.0 - 0.8 V DC AND OPERATING CHARACTERISTICS SYMBOL SPEED MIN MAX UNITS -5 - 1920 mA -6 - 1760 mA Don’t care - 32 mA -5 - 1920 mA -6 - 1760 mA -5 - 1120 mA -6 - 960 mA Don’t care - 16 mA -5 - 1920 mA -6 - 1760 mA Il(L) -10 10 µA IO(L) -5 5 µA ICC1 ICC2 ICC3 ICC4 ICC5 ICC6 VOH 2.4 - V VOL - 0.4 V ICC1 : Operating Current * (/RAS , /CAS , Address cycling @tRC=min.) ICC2 : Standby Current ( /RAS=/CAS=VIH ) ICC3 : /RAS Only Refresh Current * ( /CAS=V IH, /RAS, Address cycling @tRC=min ) URL:www.hbe.co.kr REV.1.0 (August.2002) -3- HANBit Electronics Co.,Ltd. HANBit HMD32M32M16G ICC4 : Fast Page Mode Current * (/RAS=VIL, /CAS, Address cycling @tPC=min ) ICC5 : Standby Current (/RAS=/CAS=Vcc-0.2V ) ICC6 : /CAS-Before-/RAS Refresh Current * (/RAS and /CAS cycling @t RC=min ) IIL : Input Leakage Current (Any input 0V ≤ VIN ≤ 6.5V, all other pins not under test = 0V) IOL : Output Leakage Current (Data out is disabled, 0V ≤ VOUT ≤ 5.5V VOH : Output High Voltage Level (IOH= -5mA ) VOL : Output Low Voltage Level (IOL = 4.2mA ) * NOTE: ICC1, ICC3, ICC4 and ICC6 are dependent on output loading and cycle rates. Specified values are obtained with the output open. ICC is specified as an average current. In ICC1 and ICC3, address cad be changed maximum once while /RAS=VIL. In ICC4, address can be changed maximum once within one page mode cycle. CAPACITANCE o ( TA=25 C, Vcc = 5V, f = 1Mz ) DESCRIPTION SYMBOL MIN MAX UNITS Input Capacitance (A0-A11) CIN1 - 90 pF Input Capacitance (/W) C IN2 - 122 pF Input Capacitance (/RAS0) CIN3 - 38 pF Input Capacitance (/CAS0-/CAS3) CIN4 - 38 pF Input/Output Capacitance (DQ0-31) CDQ1 - 17 pF AC CHARACTERISTICS o ( 0 C ≤ TA ≤ 70oC , Vcc = 5V±10%, See notes 1,2.) -5 PARAMETER -6 SYMBOL UNIT MIN MAX MAX Random read or write cycle time tRC Access time from /RAS tRAC 50 60 ns Access time from /CAS tCAC 13 15 ns Access time from column address tAA 25 30 ns /CAS to output in Low-Z tCLZ 3 Output buffer turn-off delay tOFF 3 13 3 15 ns Transition time (rise and fall) tT 1 50 1 50 ns /RAS precharge time tRP 30 /RAS pulse width tRAS 50 /RAS hold time tRSH 13 15 ns /CAS hold time tCSH 38 45 ns /CAS pulse width tCAS 8 10K 10 10K ns /RAS to /CAS delay time tRCD 20 37 20 45 ns /RAS to column address delay time tRAD 15 25 15 30 ns /CAS to /RAS precharge time tCRP 5 5 ns Row address set-up time tASR 0 0 ns URL:www.hbe.co.kr REV.1.0 (August.2002) 84 MIN -4- 104 ns 3 ns 40 10K 60 ns 10K ns HANBit Electronics Co.,Ltd. HANBit HMD32M32M16G Row address hold time tRAH 10 10 ns Column address set-up time tASC 0 0 ns Column Address to /RAS lead time tRAL 25 30 ns Read command set-up time tRCS 0 0 ns Read command hold referenced to /CAS tRCH 0 0 ns Read command hold referenced to /RAS tRRH 0 0 ns Write command hold time tWCH 10 10 ns Write command hold referenced to /RAS tWCR 50 55 ns Write command pulse width tWP 10 10 ns Write command to /RAS lead time tRWL 13 15 ns Write command to /CAS lead time tCWL 8 10 ns Data-in set-up time tDS 0 0 ns Data-in hold time tDH 8 10 ns Refresh period tREF Write command set-up time tWCS 0 0 ns /CAS setup time (C-B-R refresh) tCSR 5 5 ns /CAS hold time (C-B-R refresh) tCHR 10 10 ns /RAS precharge to /CAS hold time tRPC 5 5 ns 64 64 ns NOTES 1.An initial pause of 200µs is required after power-up followed by any 8 /RAS-only or /CAS-before-/RAS refresh cycles before proper device operation is achieved. 2.VIH (min) and VIL (max) are reference levels for measuring timing of input signals. Transition times are measured between VIH(min) and VIL(max) and are assumed to be 5ns for all inputs. 3.Measured with a load equivalent to 2TTL loads and 100pF 4.Operation within the tRCD(max) limit insures that tRAC(max) can be met. tRCD(max) is specified as a reference point only. If tRCD is greater than the specified tRCD(max) limit, then access time is controlled exclusively by t CAC. 5.Assumes that tRCD ≥ tRCD(max) 6. tAR, tWCR, tDHR are referenced to tRAD(max) 7.This parameter defines the time at which the output achieves the open circuit condition and is not referenced to V OH or VOL. 8. tWCS, tRWD, tCWD anf tAWD are non restrictive operating parameter. They are included in the data sheet as electrical characteristic only. If t WCS ≥ tWCS(min) the cycle is an early write cycle and the data out pin will remain high impedance for the duration of the cycle. 9. Either tRCH or tRRH must be satisfied for a read cycle. 10. These parameters are referenced to the /CAS leading edge in early write cycles and to the /W leading edge in readwrite cycles. 11. Operation within the tRAD(max) limit insures that tRAC(max) can be met. tRAD(max) is specified as a reference point only. If tRAD is greater than the specified tRAD(max) limit. then access time is controlled by tAA. AC CHARACTERISTICS URL:www.hbe.co.kr REV.1.0 (August.2002) o ( 0 C ≤ TA ≤ 70oC , Vcc = 5V±10%) -5- HANBit Electronics Co.,Ltd. HANBit HMD32M32M16G -5 PARAMETER -6 SYMBOL MIN MAX MIN UNIT NOTE 11 MAX Hyper page mode cycle time tHPC 20 25 ns /CAS precharge time (Hyper page cycle) tCP 8 10 ns /RAS pulse width (Hyper page cycle) tRASP 50 /RAS hold time from /CAS precharge tRHCP 30 35 ns /W to RAS precharge time (C-B-R refresh) tWRP 10 10 ns /W to RAS hold time (C-B-R refresh) tWRH 10 10 ns Output data hold time tDOH 5 5 ns Output buffer turn off delay from /RAS tREZ 3 13 3 15 ns 6,12 Output buffer turn off delay from W tWEZ 3 13 3 15 ns 6 /W to data delay tWED 15 15 ns /W puls width tWPE 5 5 ns 200K 60 200K ns NOTES 1. An initial pause of 200us is required after power-up followed by any 8 /RAS-only or /CAS-before-/RAS refresh cycles before proper device operation is achieved. 2. Input voltage levels are Vih/Vil. VIH(min) and VIL(max) are reference levels for measuring timing of input signals. Transition times are measured between VIH(min) and VIL(max) and are assumed to be 5ns for all inputs. 3. Measured with a load equivalent to 1 TTL loads and 100pF. 4. Operation within the tRCD(max) limit insures that tRAC(max) can be met. tRCD(max) is specified as a reference point only. If tRCD is greater than the specified tRCD(max) limit, then access time is controlled exclusively by tCAC. 5. Assumes that tRCD ≥ tRCD(max). 6. This parameter defines the time at which the output achieves the open circuit and is not referenced for V OH or VOL. 7. tWCS is non-restrictive operating parameter. It is included in the data sheet as electrical characteristics only. If tWCS ≥ tWCS(min), the cycle is an early write cycle and the data out pin will remain high impedance for the duration of the cycle. 8. Either tRCH or tRRH must be satisfied for a read cycle. 9. These parameters are referenced to the /CAS leading edge in early write cycles. 10. Operation within the tRAD(max) limit insures that tRAC(max) can be met. tRAD(max) is specified as reference point only. If tRAD is greater than the specified tRAD(max) limit access time is controlled by tAA. 11. tASC ≥6ns, Assume t T=2.0ns. 12. If /RAS goes high before /CAS high going, the open circuit condition of the output is achieved by /CAS high going. If /CAS goes high before /RAS high going , the open circuit condition of the output is achieved by /RAS going. . URL:www.hbe.co.kr REV.1.0 (August.2002) -6- HANBit Electronics Co.,Ltd. HANBit HMD32M32M16G PACKAGING INFORMATION 2.54 mm 0.25 mm MAX MIN Gold: 1.04±0.10 mm Solder: 0.914±0.10 mm 1.27 mm 1.27±0.08mm (Solder & Gold Plating) ORDERING INFORMATION Part Number Density Org. Package HMD32M32M16G-5 128Byte x 32 72 Pin-SIMM HMD32M32M16G-6 128Byte x 32 72 Pin-SIMM URL:www.hbe.co.kr REV.1.0 (August.2002) -7- Component Vcc MODE SPEED 16EA 5V FPM 50ns 16EA 5V FPM 60ns Number HANBit Electronics Co.,Ltd.