AN221E04 Datasheet Dynamically Reconfigurable FPAA With Enhanced I/O www.anadigm.com DS030100-U006a -1- Disclaimer Anadigm reserves the right to make any changes without further notice to any products herein. Anadigm makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Anadigm assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including with out limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Anadigm does not in this document convey any license under its patent rights nor the rights of others. Anadigm software and associated products cannot be used except strictly in accordance with an Anadigm software license. The terms of the appropriate Anadigm software license shall prevail over the above terms to the extent of any inconsistency. © Anadigm® Ltd. 2003 © Anadigm®, Inc. 2003 All Rights Reserved. DS030100-U006a -2- AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O PRODUCT AND ARCHITECTURE OVERVIEW The AN221E04 device consists of a 2x2 matrix of fully Configurable Analog Blocks (CABs), surrounded by a fabric of programmable interconnect resources. Configuration data is stored in an on-chip SRAM configuration memory. Compared with the first-generation FPAAs, the Anadigmvortex architecture provides a significantly improved signal-to-noise ratio as well as higher bandwidth. These devices also accommodate nonlinear functions such as sensor response linearization and arbitrary waveform synthesis. The AN221E04 device features an advanced input/output structure that allows the FPAA to be programmed with up to six outputs – or triple the number provided by the ANx20E04 devices. The AN221E04 devices have four configurable I/O cells and two dedicated output cells. For I/O-intensive applications, this means a single FPAA can now be used to process multiple channels of analog signals where two or more such devices were previously needed. In addition, the AN221E04 devices allow designers to implement an integrated 8-bit analog-to-digital converter on the FPAA, eliminating the potential need for an external converter. Using this new device, designers can route the digital output of the A/D converter off-chip using one of the dedicated output cells. PRODUCT FEATURES • • • • • • • • • • • • • • Dynamic reconfiguration Four configurable I/O cells, two dedicated output cells 8-bit SAR analog–to–digital converter Fully differential architecture Fully differential I/O buffering with options for single ended to differential conversion Low input offset through chopper stabilized amplifiers 256 Byte Look-Up Table (LUT) for linearization and arbitrary signal generation 4:1 Input multiplexer Typical Signal Bandwidth: DC-2MHz (Bandwidth is CAM dependent) Signal to Noise Ratio: o Broadband 80dB o Narrowband (audio) 100dB Total Harmonic Distortion (THD): 80dB DC offset <100µV Package: 44-pin QFP (10x10x2mm) o Lead pitch 0.8mm Supply voltage: 5V Figure 1: Architectural overview of the AN221E04 device With dynamic reconfigurability, the functionality of the AN221E04 can be reconfigured in-system by the designer or on-the-fly by a microprocessor. A single AN221E04 can thus be programmed to implement multiple analog functions and/or to adapt on-the-fly to maintain precision operation despite system degradation and aging. APPLICATIONS • • • • • • • • • • Real-time software control of analog system peripherals Intelligent sensors Adaptive filtering and control Adaptive DSP front-end Adaptive industrial control and automation Self-calibrating systems Compensation for aging of system components Dynamic recalibration of remote systems Ultra-low frequency signal conditioning Custom analog signal processing ORDERING CODES AN221E04-QFPSP AN221E04-QFPTY AN221E04-QFPTR AN221D04-EVAL AN221D04-DEVLP Dynamically reconfigurable FPAA Sample Pack Dynamically reconfigurable FPAA Tray (96 pcs) Dynamically reconfigurable FPAA Tape & Reel (1000 pcs) AN221E04 Evaluation Kit AN221E04 Development Kit [For more detailed information on the features of the AN221E04 device, please refer to the AN121E04/AN221E04 User Manual] DS030100-U006a -3- AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings Parameter DC Power Supplies Symbol Min Typ Max Unit AVDD(2) BVDD DVDD -0.5 - 5.5 V V 0.5 V xVDD to xVDD Offset Package Power Dissipation Analog and Digital Input Voltage Ambient Operating Temperature Storage Temperature a -0.5 Pmax 25°C Pmax 85°C Vinmax Top Tstg - - Vss-0.5 -40 -65 - 1.8 0.73 Vdd+0.5 85 150 W Comment AVSS, BVSS, DVSS and SVSS all held to 0.0 V a Ideally all supplies should be at the same voltage Still air, No heatsink, 4 layer board, 44 pins. θja = 55°C/W V °C °C Absolute Maximum DC Power Supply Rating - The failure mode is non-catastrophic for Vdd of up to 7 volts, but will cause reduced operating life time. The additional stress caused by higher local electric fields within the CMOS circuitry may induce metal migration, oxide leakage and other time/quality related issues. Recommended Operating Conditions Parameter Symbol Min Typ Max Unit AVDD(2) BVDD DVDD 4.75 5.00 5.25 V Analog Input Voltage. Vina VMR-1.9 Digital Input Voltage Junction Temp Vind Tj DC Power Supplies b 0 -40 Comment AVSS, BVSS, DVSS and SVSS all held to 0 V - VMR+1.9 V VMR is 2.0 volts above AVSS - DVDD 125 V °C Assume a package θja = 55°C/W b In order to calculate the junction temperature you must first empirically determine the current draw (total Idd) for the design. Once the current consumption established then the following formula can be used; Tj = Ta + Idd x Vdd x 55 °C/W, where Ta is the ambient temperature. The worst case θja of 55 °C/W assumes no air flow and no additional heatsink of any type. General Digital I/O Characteristics (Vdd = 5v +/- 10%, -40 to 85 deg.C) Parameter Input Voltage Low Input Voltage High Output Voltage Low Output Voltage High Input Leakage Current Input Leakage Current Max. Capacitive Load Min. Resistive Load DCLK Frequency ACLK Frequency Clock Duty Cycle Symbol Min Typ Max Unit Vih Vil Vol Voh Iil 0 70 0 80 - - 30 100 20 100 ±1.0 µA Iil - ±12.0 - µA Cmax - - 10 pF Rmin 10 - - Kohm Fmax - - 40 MHz Fmax - - 40 MHz - 45 - 55 % Comment % of DVDD % of DVDD % of DVDD % of DVDD All pins except DCLK DCLK if a crystal is connected and the on-chip oscillator is used The maximum load for a digital output is 10 pF // 10 Kohm The maximum load for a digital output is 10 pF // 10 Kohm For MODE = 1, Max DCLK is 16 MHz Divide down to <8 MHz prior to use as a CAB clock All clocks DS030100-U006a -4- AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O Detailed Digital I/O Interface Characteristics: Vdd = 5.0volts LCCb Parameter Symbol Min Typ Max Unit Comment Output Voltage Low Output Voltage High Max. Capacitive Load Min. Resistive Load Current Sink Current Source Vol Voh Cmax Rmin Isnkmax Isrcmax Vss 4.5 50 - - 150 Vdd 20 15 4 mV V pF Kohm mA mA Load 20pF//50Kohm to Vss Load 20pF//50Kohm to Vss Maximum load 20 pF // 50 Kohm Maximum load 20 pF // 50 Kohm LCCb pin shorted to Vdd LCCb pin shorted to Vss Symbol Min Typ Max Unit Comment Vil Vih 0 70 30 100 % % Vol Vss - 85 mV Voh 4.5 - Vdd V Vol Vss - 200 mV Voh 4.5 - Vdd V Cmax Rmin Isnkmax Isrcmax 50 - - 50 2.5 200 pF Kohm mA µA Rpullupext 5 7.5 10 Kohm Symbol Min Typ Max Unit Comment Vil Vih Vol Voh Cmax Rmin Isnkmax Isrcmax Rpullupext 0 70 Vss 4.9 50 10 % % mV V pF Kohm mA µA Kohm % of DVDD % of DVDD 10 30 100 50 Vdd 50 10 0 10 CFGFLG, ACTIVATE Parameter Input Voltage Low Input Voltage High Output Voltage Low Output Voltage High Output Voltage Low Output Voltage High Max. Capacitive Load Min. Resistive Load Current Sink Current Source External Resistive Pullup % of DVDD % of DVDD Pin load = Internal pullup + 20pF//50K to Vss Pin load = Internal pullup + 20pF//50K to Vss Pin Load = External 5K ohm pullup + 20pF//50K to Vss Pin Load = External 5Kohm pullup + 20pF//50K to Vss Maximum load 50 pF // 50 Kohm Maximum load 50 pF // 50 Kohm Pin shorted to Vdd Pin shorted to Vss Use only if internal pullup is deselected ERRb Parameter Input Voltage Low Input Voltage High Output Voltage Low Output Voltage High Max. Capacitive Load Min. Resistive Load Current Sink Current Source External Resistive Pullup Maximum load 50 pF // 50 Kohm Maximum load 50 pF // 50 Kohm DCLK,Mode,DIN,EXECUTE,PORb,CS1b,CS2b Parameter Input Voltage Low Input Voltage High Symbol Min Typ Max Unit Comment Vil Vih 0 70 - 30 100 % % % of DVDD % of DVDD DS030100-U006a -5- AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O OUTCLK/SPIMEM,DOUTCLK Parameter Symbol Min Typ Max Unit Comment Output Voltage Low Output Voltage High Max. Capacitive Load Min. Resistive Load Current Sink Current Source Vol Voh Cmax Rmin Isnkmax Isrcmax 0 80 10 - - 20 100 50 17 4 % % pF Kohm mA mA % of DVDD % of DVDD Maximum load 50 pF // 50 Kohm Maximum load 50 pF // 50 Kohm Parameter Symbol Min Typ Max Unit Comment Input Voltage Low Input Voltage High Output Voltage Low Output Voltage High Max. Capacitive Load Min. Resistive Load Current Sink Current Source Vil Vih Vol Voh Cmax Rmin Isnkmax Isrcmax 0 70 0 80 10 - - 30 100 20 100 50 15 4 % % % % pF Kohm mA mA % of DVDD % of DVDD % of DVDD % of DVDD Maximum load 50 pF // 50 Kohm Maximum load 50 pF // 50 Kohm ACLK/SPIP DS030100-U006a -6- AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O Analog Inputs General Parameter High Precision Input Range c Standard precision Input Range d High Precision Differential Input c Standard Precision Differential Input d Common Mode Input Range Input Offset Input Frequency c. d. Symbol Min Typ Max Unit Vina Vina 0.5 0.1 - 3.5 3.9 V V Vdiffina 0 - +/-3.0 V Vdiffina 0 - +/-3.8 V Vcm 1.8 2.0 2.2 V Vos - 5 15 mV Fain 0 <2 8 MHz Comment VMR +/- 1.5v VMR +/- 1.9v Common mode voltage = 2 V Common mode voltage = 2 V Non-chopper stabilized input Max value is clock, CAM and input stage dependant. Input frequency is limited to approx <2MHz due to CAM signal processing which is based on sampled data architectures. High precision operating range provides optimal linearity and dynamic range. Standard precision operating range provides maximum dynamic range and reduced linearity. Input Differential Amplifier ON and filter OFF Parameter Input Range Gain Setting Gain Accuracy Gain Drift (Temperature, Supply Voltage zand Time) Equivalent Input Offset Voltage Symbol Vina Vdiffina Ginamp Dist Min Typ Max Unit 16 - 1.0 128 2.5 % - - 1.0 % Vos - 3 12 mV Voffsettc - 1 10 µV/°C Fain Fain 0 0 <2 2 8 MHz MHz PSRR 65 - - dB CMRR - 67 - dB Large Signal Harmonic Distortion Dist - -65 - dB Input Resistance Input Capacitance Input Referred Noise Figure Rin Cin 10 - 5.0 Mohm pF NF - 0.1 - µV/sqrtHz SINAD - 75 - dB SFDR - 73 - dB Offset Voltage Temperature Coefficient Input Frequency c Input Frequency d Power Supply Rejection Ratio Common Mode Rejection Ratio Signal-to Noise Ratio and Distortion Spurious Free Dynamic Range c. d. Comment Usable input range will be reduced by the effective gain setting See analog input above Non-chopper stabilized input When the input amplifier and filter are used in combination Vos contribution comes only from the input amplifier from -40°C to 125°C d.c. Amp Gain =16 a.c. See graphs page 18 0.4v p-p Differential input at 660Hz Gain setting = 16 Input cell Gain = 16 Applies to audio frequency range (400Hz to 30KHz). See graphical data on page 18 Input signal = 285 mV p-p diff, audio frequency range See graphical data on page 18 Input signal = 100 mV p-p diff See graphical data on page 18 High precision operating range provides optimal linearity and dynamic range. Standard precision operating range provides maximum dynamic range and reduced linearity. DS030100-U006a -7- AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O Input Differential Chopper Amplifier on and filter OFF Parameter Input Range Gain Setting Gain Accuracy Gain Drift, (Temperature, Supply Voltage and Time) Chopper Frequency Clock Range Symbol Vina Vdiffina Ginamp Min Typ Max Unit Comment Usable input range will be reduced by the effective gain setting See analog input above 16 - 1.0 128 2.5 % - - 1.0 % Fch Fc/260100 - >250 KHz Vos - <100 200 µV Voffsettc - 0.5 2.0 µV/°C Fc = master clock frequency Set Fch as slow as possible Fch > 250KHz will result in some signal attenuation Chopper stabilized amplifier The maximum value of 200µV is guaranteed by production test This is a tester limitation Equivalent Input Offset Voltage Offset Voltage Temperature Coefficient Power Supply Rejection Ratio Common Mode Rejection Ratio Large Signal Harmonic Distortion PSRR 65 - - dB CMRR - 102 - dB Dist - -40 - dB Fain 0 Fch/20 Fch/2 KHz Rin Cin 10 - 5.0 Mohm pF from -40°C to 125°C d.c. a.c. See graphs on page 18 0.4v p-p Differential input at 660Hz Gain setting = 16 Fch=Chopper clock frequency The chopper frequency and input frequency should be chosen such that subsequent low pass filtering can remove the chopper stage frequency elements Input to filter or chopper Input Frequency Input Resistance Input Capacitance Input Referred Noise Figure Signal-to Noise Ratio and Distortion NF - 0.09 - µV/sqrtHz SINAD - 75 - dB SFDR - 74 - dB Spurious Free Dynamic Range Input cell Gain = 16 Applies to Audio frequency range Chopper clock Fch = 250KHz See graphical data on page 18 Input signal = 285 mV p-p differential, Audio frequency range See graphical data on page 18 Input signal =100 mV p-p differential See graphical data on page 18 Input Differential Amplifier OFF and filter ON Parameter Symbol Min Input Range Vina Vdiffina See analog input above Equivalent Input Offset Offset Voltage Temperature Coefficient Typ Max Unit Vos - 8 32 mV Voffsettc - 0.05 I 1.0 II mV/°C Fain - - - MHz Input Frequency Comment Non-chopper stabilized input, Filter corner frequency =470KHz from -40°C to 125°C I. measured at filter corner=470Khz II. maximum at Filter corner=76KHz Input filter frequency will define the maximum frequency Input filter is recommended to be >30x higher than the max input frequency, for 80dB distortion performance DS030100-U006a -8- AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O Common Mode Rejection Ration Power Supply Rejection Ratio CMRR - 60 - dB PSRR 68 - - dB Large Signal Harmonic Distortion Dist - -82 - dB Ffiltcorner 76 - 470 KHz Rin Cin 10 - - 5.0 Mohm pF NF - 0.17 - µV/sqrtHz SINAD - 84 - dB SFDR - 90 - dB Input Low Pass Filter (Anti-Alias) Corner Frequency Settings Input Resistance Input Capacitance Input Referred Noise Figure Signal-To Noise Ratio and Distortion Spurious Free Dynamic Range d.c. a.c. See graphical data on page 19 4v p-p Differential input at 660Hz Filter corner frequency 470KHz Input to filter or chopper Input cell filter corner Fc = 470KHz Applies to Audio frequency range See graphical data on page 18 Input signal = 1400 mV p-p diff, Audio frequency range See graphical data on page 18 Input signal =1400 mV p-p differential See graphical data on page 18 Input Differential Voltage mode, Amplifier OFF, Filter OFF and Unity Gain stage ON Parameter Input Range Equivalent Input Offset Offset Voltage Temperature Coefficient Input Frequency Power Supply Rejection Ratio Common Mode Rejection Ratio Large Signal Harmonic Distortion Large Signal Harmonic Distortion Input Resistance Input Capacitance Input Referred Noise Figure Signal-To Noise Ratio and Distortion Spurious Free Dynamic Range Symbol Vina Vdiffina Vos Min Typ Max See analog input above Unit Comment V - 5 15 mV Voffsettc - 20 50 µV/°C Fain - - 1.0 MHz PSRR 60 - - dB CMRR Dist Dist Rin Cin - 60 -80 -80 126 2.0 5.0 dB dB dB Kohm pF NF - 0.16 - µV/sqrtHz SINAD - 84 - dB SFDR - 90 - dB Non-chopper stabilized input from -40°C to 125°C Gain Bandwidth limited by input impedance d.c. a.c. See graphs on page 18 4v p-p Differential input at 660Hz 3v p-p single ended signal at 660Hz Input to unity gain stage Applies to Audio frequency range See graphical data on page 18 Input signal = 1400 mV p-p diff, Audio frequency range See graphical data on page 18 Input signal =1400 mV p-p differential See graphical data on page 18 Input Differential Voltage mode, Amplifier OFF, Filter OFF and Unity Gain stage OFF Parameter Input Range Equivalent Input Offset Offset Voltage Temperature Coefficient Input Frequency Power Supply Rejection Ratio Large Signal Harmonic Distortion Input Resistance Symbol Vina Vdiffina Vos Min Typ Max See analog input above Unit Comment V N/A N/A N/A mV Voffsettc N/A N/A N/A µV/°C Fain PSRR Dist N/A - N/A -85 8 N/A - MHz dB dB Rin - - - Mohm Cin - - - pF Input Capacitance See CAM Op Amp See CAM Op Amp. from -40°C to 125°C Dependant upon CAM See CAM Op Amp See CAM Op Amp Input to CAM directly (Input cell bypass mode). This variable is influenced by CAB capacitor size, CAB clock frequency and CAB architecture Input to CAM directly (Input cell bypass mode) This variable is influenced by CAB capacitor size, CAB clock frequency and CAB architecture DS030100-U006a -9- AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O Analog Outputs (See “Output Cell” section in the AN120E04/AN220E04 user manual for more details) Parameter High Precision Output Range c Standard Precision Output Range d High Precision Differential Output c Standard precision Differential Output d Common Mode Voltage c Symbol Min Typ Max Unit Vouta 0.5 - 3.5 V Vouta 0.1 - 3.9 V Vdiffouta - - +/-3.0 V Vdiffouta - - +/-3.8 V Vcm 1.9 2.0 2.1 V Comment VMR +/- 1.5v VMR +/- 1.9v Common mode voltage = 2 V Common mode voltage = 2 V . High precision operating range provides optimal linearity and dynamic range. . Standard precision operating range provides maximum dynamic range and reduced linearity. d Output Voltage mode and filter ON, corner frequency 470KHz Parameter Input Range Equivalent Input Offset Offset Voltage Temperature Coefficient Symbol Vina Vdiffina Vos Min Typ Max See analog input above - Voffsettc Unit 5 15 mV 0.05 I 1.0 II mV/°C Output Frequency Power Supply Rejection Ratio Large Signal Harmonic Distortion Input Low Pass Filter (Anti-Alias) Corner Frequency Settings Output Load c e Output Load c e Output Load d e Output Load d e Common Mode Rejection Ratio Faout - - - MHz PSRR 60 - - dB Dist - -82 - dB Ffiltcorner 76 - 470 KHz Rload Cload 0.1 - - 50 Mohm pF Rload 1 10 - Kohm Cload - - 100 pF CMRR - 56 - dB NF - 0.22 - µV/sqrtHz SINAD - 82 - dB SFDR - 90 - dB Input Referred Noise Figure Signal-To Noise Ratio and Distortion Spurious Free Dynamic Range Comment V from -40°C to 125°C I measured at filter corner: 470Khz II maximum at filter corner: 76KHz Output filter frequency will define the maximum frequency Input filter is recommended to be >30x higher then the max input frequency, for good distortion performance d.c. a.c. See graphical data on page 19 4v p-p Differential input at 660Hz Filter corner frequency 470KHz Additional loading causes internal voltage drops across output stage and series resistances The output stage has a small signal output impedance of approx 10ohm Output filter corner fc = 470KHz Applies to Audio frequency range See graphical data on page 18 Input signal = 1400 mV p-p diff, Audio frequency range See graphical data on page 18 Input signal =1400 mV p-p diff See graphical data on page 18 c . High precision operating range provides optimal linearity and dynamic range. . Standard precision operating range provides maximum dynamic range and reduced linearity. e . The maximum load for an analog output is 50 pF // 100 Kohms. This load maybe with respect to analog ground VMR or AVSS. d DS030100-U006a - 10 - AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O Output Voltage mode and filter off (bypass mode) Parameter Symbol Input Range Equivalent Input Offset Offset Voltage Temperature Coefficient Output Frequency c e Output Frequency d f Power Supply Rejection Ratio Large Signal Harmonic Distortion Output Load Output Load Min Typ Max Unit Comment V Vina Vdiffina Vos N/A N/A N/A mV See CAM Op Amp Voffsettc N/A N/A N/A mV/°C See CAM Op Amp Faout - - 4 MHz See analog input above Faout - - 8 MHz PSRR Dist Rload Cload N/A N/A N/A N/A -85 N/A N/A N/A N/A N/A dB dB Mohm pF The realizable output frequency is limited to approx <2MHz due to CAM signal processing which is based on sampled data architectures. See CAM Op Amp See CAM Op Amp See CAM Op Amp c . High precision operating range provides optimal linearity and dynamic range. . Standard precision operating range provides maximum dynamic range and reduced linearity. . The maximum load for an analog output is 50 pF // 100 Kohms. This load maybe with respect to analog ground VMR or AVSS. f . The maximum load for an analog output is 100 pF // 100 Kohms. This load must be differential and with respect to analog ground(VMR). d e VMR (voltage Mid Rail) and VREF (Reference Voltage) Ratings Parameter VMR Output Voltage VREF+ Output Voltage VREF- Output Voltage Output Voltage Deviation VREF+, VMR, VREFVoltage Temperature Coefficient VREF+, VMR, VREFPower Supply Rejection Ratio, VMR Power Supply Rejection Ratio Vref+ and VrefStart Up Time Min Typ Max Unit Vvmr Vref+ Vref- 1.925 3.4 0.45 2.01 3.51 0.505 2.075 3.6 0.55 V V V Vrefout - 0.5 1 % Vreftc - - - - PSSR 60 - - dB PSSR 75 - - dB Tstart - - 1 ms V+ref vs temperature 2.010 3.500 3.495 -50 0 50 Tchip (C) 100 150 At 25°C, Vdd=5.00 volts At 25°C, Vdd=5.00 volts At 25°C, Vdd=5.00 volts Over process and supply voltage corners See typical graphical data below -40°C to 125°C f Assuming recommended capacitors Vref- vs temperature 0.505 2.000 1.995 3.490 Comment 0.510 2.005 Volts Volts 3.505 VMR vs temperature Volts 3.510 Symbol 0.500 0.495 1.990 0.490 -50 0 50 Tchip (C) 100 150 -50 0 50 100 150 Tchip (C) DS030100-U006a - 11 - AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O CAB (Configurable Analog Block) Differential Operational Amplifier Parameter Symbol Min Typ Max Unit Vinouta 0.5 - 3.5 V Vinouta 0.1 - 3.9 V Vdiffioa - - +/-3.0 V Vdiffioa - - +/-3.8 V Vcm 0 2.0 4 V Vcm 1.9 2.0 2.1 V Voffset 0.1 5 15 mV Voffsettc - 1 10 µV/°C PSSR - 80 - dB CMRR - 77 - dB CMRR - 60 - dB Differential Slew Rate, Internal Slew - 50 - V/µsec Differential Slew Rate, External Slew - 10 - V/µsec Unity Gain Bandwidth, Full Power Mode. UGB - 50 - MHz Rin 10 - - Mohm Output Impedance, Internal Rout - - - Ohms Output Impedance, External Rout - - - Ohms Output Load, External c e Output Load, External c e Output Load, External d e f Rload Cload 0.1 - - 50 Mohm pF High Precision Input/Output Range c Standard Precision Input/Output Range d High Precision. Differential Input/Output c Standard Precision Differential Input/Output d Common Mode Input Voltage Range d Common Mode Output Voltage Range Equivalent Input Voltage Offset. Offset Voltage Temperature Coefficient Power Supply Rejection Ratio Common Mode Rejection Ratio Common Mode Rejection Ratio Input Impedance, Internal Output Load, External d e f Noise Figure g Rload 1 10 - Kohm Cload - - 50 pF Noise - 0.13 - µV/sqrtHz Comment VMR +/- 1.5v VMR +/-1.9v Common mode voltage = 2 V Common mode voltage = 2 V Some CAMs (Configurable Analog Modules) can inherently compensate from -40°C to 125°C some CAMs (Configurable Analog Modules) can inherently compensate Variation between CAMs is expected because of variations in architecture Example 1 GainInv CAM CAM clock = 1MHz CAM parameter settings Gain = 1 Example 2 Filterbiquad Setting = Low pass filter CAM clock = 1MHz CAM parameter settings Gain = 1, Corner frequency = 50KHz Quality Factor = 0.707 Applicable when the OpAmp load is internal to the FPAA Applicable when the OpAmp driving signal out of the FPAA package Applicable when sourcing and loading the OpAmp with a load internal to the FPAA The OpAmp output is designed to drive all internal nodes, these are dominantly capacitive loads Output to an FPAA output pin (ouput cell bypass mode). This variable is influenced by CAB capacitor size, CAB clock frequency and CAB architecture Additional loading causes internal voltage drops across output stage and series resistances The output stage has a small signal output impedance of approx 10ohm Example1 GainInv CAM CAM clock = 1MHz Gain = 1 DS030100-U006a - 12 - AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O Signal-To Noise Ratio and Distortion g SINAD - 80 - dB SFDR - 92 - dB Spurious Free Dynamic Range g Input signal=1400 mV p-p differential Audio frequency range Example. GainInv CAM CAM clock = 1MHz Gain = 1 Input signal=1400 mV p-p differential, Audio frequency range Example. GainInv CAM CAM clock = 1MHz Gain = 1 c . . . f . High precision operating range provides optimal linearity and dynamic range. Standard precision operating range provides maximum dynamic range and reduced linearity. The maximum load for an analog output is 50 pF || 100 Kohms. This load may be with respect to analog ground VMR or AVSS. Using the FPAA with CAB Op Amp’s driving directly off-chip, requires care, full characterization of the performance of each application circuit by the circuit designer is necessary. g . This specification parameter can only be characterized when a circuit topology is configured onto the CAB differential amplifier architecture. The figure provided here is an representative on the performance of one specific CAM, as specified in the comments. d e Open Loop Gain (dB) Idealized CAB Op Am p, Open Loop Gain [dB] 90 80 70 60 50 40 30 20 10 0 -10 -20 The idealized open loop gain plot is provided for information only. This information is associated with the FPAA in full power mode of operation. The FPAA operation amplifier open loop gain cannot be observed nor used when associated with external connections to the device. Internal reprogrammable routing impedances and switched capacitor circuit architecture using this operational amplifier limit the effective usable bandwidth of a circuit realized in the FPAA to less than 2MHz. 0.1 10 1000 100000 Frequency (KHz) DS030100-U006a - 13 - AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O CAB (Configurable Analog Block) Differential Comparator Parameter Input Range, Internal Input Range, External Differential Input, Internal Differential Input, External Common Mode Output Voltage Range, Internal c Common Mode Input Voltage Range, External c Common Mode Input Voltage, External d Differential Output Single Pin Output (Ox1P) Input Voltage Offset Offset Voltage Temperature Coefficient Setup Time, Internal Setup Time, External Delay Time Symbol Min Typ Max Unit Vina Vina Vdiffina Vdiffina 0.1 0.0 +/- 0.0 - 3.9 Vdd +/-3.8 +/- Vdd V V V V Vcm 1.9 2.0 2.1 V Vcm 0 2.0 4 V Vcm 0 - 5 V Voutdiff Vout Voffcomp 0 - 2 +/-5 5 10 V V mV Voffsettc - 1 10 µV/°C Tsetint Tsetext - - 125 500 nsec nsec Tdelay ½Td+25 - 1½Td+25 nsec Rload 10 - - Kohm Cload - - 50 pF CompVref 0 - +/-4.0 V Hysta1 Hysta2 Hysta3 Hysta4 Hystb - Voffcomp 20 40 80 25 - mV mV mV mV % Hysttc1 - 5 - µV/°C Hysteresis setting = zero Hysttc2 - 50 - µV/°C Hysteresis setting = 10mV Hysttc3 - 100 - µV/°C Hysteresis setting = 20mV Hysttc4 - 200 - µV/°C Hysteresis setting = 40mV Output Load Output Load Differential Variable Reference Voltage Settings Differential Hysteresis Differential Hysteresis Differential Hysteresis Differential Hysteresis Hysteresis Setting Accuracy Hysteresis Temperature Coefficient Hysteresis Temperature Coefficient Hysteresis Temperature Coefficient Hysteresis Temperature Coefficient c Comment Common mode voltage = 2 V The comparator will function correctly Zero hysterisis from -40°C to 125°C, Zero Hysterisis Td = 1/Fc Fc = master clock frequency Applies if comparator drive off chip with output cell in bypass mode Applies if comparator drive off chip with output cell in bypass mode Hysteresis setting = zero Hysteresis setting = 10mV Hysteresis setting = 20mV Hysteresis setting = 40mV . High precision operating range provides optimal linearity and dynamic range. . Standard precision operating range provides maximum dynamic range and reduced linearity. d DS030100-U006a - 14 - AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O ESD Characteristics Pin Type Human Body Model Machine Model Charged Device Model Digital Inputs Digital Outputs Digital Bidirectional Digital Open Drain Analog Inputs Analog Outputs Reference Voltages 4000V 4000V 4000V 4000V 2000V 1500V 1500V 250V 250V 250V 250V 200V 100V 100V 4kV 4kV 4kV 4kV 4kV 4kV 4kV The AN221E04 is an ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000V readily accumulate on the human body and test equipment and can discharge without detection. Although the AN221E04 device features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Power Consumption – Low Power Mode Symbol Min Typ Max Unit Idd Idd Idd Idd - - - 30 47 55 68 -10 mA mA mA mA Idd 0.2 25 42 50 60 63 66 -2 Minimum Power 1a Nominal 25% Power1b Nominal 50% Power 1c Nominal 75% Power1d Maximum Power1e Temperature Coefficient mA Comment Vdd=5.00 volts, Tj=25°C Vdd=5.00 volts, Tj=25°C Vdd=5.00 volts, Tj=25°C Vdd=5.00 volts, Tj=25°C Vdd=4.75 volts, Tj=85°C Vdd=5.00 volts, Tj=25°C Vdd=5.25 volts, Tj= -40°C µA/°C 1a. External clock, all analog function disabled, memory active. 1b FPAA active elements – Two core op-amps (low power mode), one comparator, one input (bypass mode), one output filter and differential to single-ended converter (low power mode). 1c. FPAA active elements – Four core op-amps (low power mode), two comparators (one using SAR), two inputs (bypass mode), two output filters and two differential to singleended converters (low power mode). 1d FPAA active elements – Six core op-amps (low power mode), three comparators (two using SAR), three inputs (bypass mode, two output filters and two differential to single-ended converters (low power mode). 1e FPAA active elements – Eight core op-amps (low power mode), four comparators (two using SAR), four inputs (bypass mode), two output filters and two differential to singleended converters (low power mode). Power consumption low power mode (temp 25 degree C) 70 60 50 Idd (mA) Parameter 40 30 20 Vdd=4.75V Vdd=5.0V Vdd=5.25V 10 0 25% 50% 75% 100% Resource Utilization Power Consumption – Full Power Mode Full Power Mode Minimum Power 2a Full Power Mode Nominal 25% Power2b Full Power Mode Nominal 50% Power2c Full Power Mode Nominal 75% Power2d Full Power Mode Maximum Power2e Symbol Min Typ Max Idd Idd Idd Idd - 1.5 80 150 170 90 160 190 Unit mA mA mA mA Vdd=5.00 volts, Tj=25°C Vdd=5.00 volts, Tj=25°C Vdd=5.00 volts, Tj=25°C Vdd=5.00 volts, Tj=25°C Idd - 200 210 220 230 - mA Vdd=4.75 volts, Tj=85°C Vdd=5.00 volts, Tj=25°C Vdd=5.25 volts, Tj= -40°C 2a. AN220E04 Crystal Oscillator, all analog functions disabled, memory active. 2b. FPAA active elements – Two core op-amps, one comparator, one input filter and chopper amplifier, one output filter and differential to single-ended converter. 2c. FPAA active elements – Four core op-amps, two comparators (one using SAR), two Input filters and two chopper amplifiers, two output filters and two differential to single-ended converters. 2d FPAA active elements – Six core op-amps, three comparators (two using SAR), three input filters and three chopper amplifiers, two output filters and two differential to single-ended converters. 2e FPAA active elements – Eight core op-amps, four comparators (two using SAR), four input filters and two chopper amplifiers, two output filters and two differential to single-ended converters. Comment Power consumption full power mode (temp 25 degree C) 250 200 Idd (mA) Parameter 150 100 Vdd=4.75V Vdd=5.0V Vdd=5.25V 50 0 25% 50% 75% 100% Resource Utilization DS030100-U006a - 15 - AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O PINOUT Pin Numb er Pin Name Pin Type 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 I4PA I4NA O1P O1N AVSS AVDD O2P O2N I1P I1N I2P I2N SHIELD AVDD2 VREFMC VREFPC VMRC BVDD BVSS CFGFLGb Analog IN+ Analog INAnalog OUT+ Analog OUTAnalog Vss Analog Vdd Analog OUT Analog OUT Analog IN+ Analog INAnalog IN+ Analog INAnalog Vdd Analog Vdd Vref Vref Vref Analog Vdd Analog Vss Digital IN Digital OUT 21 CS2b Digital IN 22 CS1b 23 24 25 DCLK SVSS MODE Digital IN (during config) Digital IN (after config)_ Digital IN Digital Vss Digital IN 26 ACLK / SPIP 27 28 29 30 31 OUTCLK / SPIMEM DVDD DVSS DIN LCCb 32 ERRb Digital IN (monitored OUT) Digital OUT 33 ACTIVATE Digital IN 34 35 DOUTCLK / TEST PORb Digital OUT Digital IN Digital IN 36 EXECUTE Digital IN 37 38 39 I3P I3N I4PD Analog IN+ Analog INAnalog IN+ 40 41 I4ND I4PC Analog INAnalog IN+ 42 I4NC Analog IN- 43 I4PB Analog IN+ 44 I4NB Analog IN- Digital IN Digital OUT Digital OUT Digital OUT Digital Vdd Digital Vss Digital IN Digital OUT Comments Low noise Vdd bias for capacitor array n-wells Analog power Attach filter capacitor for VREFAttach filter capacitor for VREF+ Attach filter capacitor for VMR (Voltage Main Reference) Analog power for bandgap Vref Generators Analog ground for bandgap Vref Generators In multi-device systems... 0, Ignore incoming data (unless currently addressed) 1, Pay attention to incoming data (watching for address) 0, Device is being configured Z, Device is not being configured (if internal pullup is selected) 0, Chip is selected 1, Chip is not selected 0, Allow configuration to proceed 1, Hold off configuration Passes read-back data through to LCC_B pin Digital ground - substrate tie 0, Synchronous serial interface 1, SPI EPROM Interface MODE = 0, analog clock < 40 MHz MODE = 1, SPI EPROM or serial EPROM clock During power-up, sources SPI EPROM initialization command string After power-up, sources any of the four internal analog clocks Serial configuration data input 1, Local configuration is needed. Once configuration is completed, it is a registered version of CS1b or if the device is addressed for read, it serves as serial data out port 0, Initiate reset 1, No action 0, Error condition Z, No error condition (external pullup required) 0, Hold off completion of configuration Rising Edge, Allow completion of configuration O.D. Output 0, device has not yet completed primary configuration Z, Device has completed primary configuration (if internal pullup is selected) A buffered version of DCLK. (Factory reserved test input. Float if unused) 0, Chip held in reset state Rising edge, re-initiates power on reset sequence To initiate a POR reset cycle, the minimum pulse width required on the PORb pin is 25ns. 0, No action 1, Transfer shadow RAM into configuration RAM Analog multiplexer input signals. The multiplexer can accept 4 differential inputs or 8 single ended inputs DS030100-U006a - 16 - AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O MECHANICAL AND HANDLING The AN221E04 comes in the industry standard 44 lead QFP package. Dry pack handling is recommended. The package is qualified to MSL3 (JEDEC Standard, J-STD-020A, Level 3). Once the device is removed from dry pack, 30°C at 60% humidity for not longer than 168 hours is the maximum recommended exposure prior to solder reflow. If out of dry pack for longer than this recommended period of time, then the recommended bake out procedure prior to solder reflow is 24 hours at 125°C. DS030100-U006a - 17 - AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O Distortion, SINAD and SNR Measurements The following plots give an indication of the Distortion, SINAD and SNR for some representative CAMs. INPUT CELL UGB SNR, DSTN, SINAD INPUT CELL LOW PASS FILTER SNR, DSTN, SINAD 120 100 80 60 SNR[ dB] SINAD[ dB] [dB] [dB] 120 100 80 60 40 20 0 DISTN[ dB] -20 -40 -60 40 20 SNR[ dB] 0 SINAD[ dB] -20 DISTN[ dB] -40 -60 -80 -100 -80 0.7 1.4 2.8 5.6 7.0 -100 0.7 INPUT [Vp-p] 1.4 2.8 INPUT [Vp-p] 5.6 7.0 100.00 80.00 60.00 INPUT CELL AMPLIFIER SNR,DSTN,SINAD Measured with Inputcell Gain G = 16 Same results for Input Amplifier and Chopper Amplifier stage, If the signal from the chopper Amplifier is correctly filtered before measurement. [dB] 40.00 20.00 0.00 SNR[ dB] -20.00 SINAD[ dB] -40.00 DISTN[ dB] -60.00 -80.00 -100.00 0.08 0.14 0.21 0.28 0.35 0.42 0.49 INPUT [Vp-p] [dB] Output Cell SNR, DSTN, SINAD 120 100 80 60 40 20 0 -20 -40 -60 -80 -100 SNR[dB] SINAD[dB] DISTN[dB] 0.7 1.4 2.8 3.5 5.6 7.0 INPUT [Vp-p] 100 80 GAININV CAM SNR, DSTN, SINAD This graph shows the typical performance of an FPAA CAB when configured with a CAM in this example GainInv CAM Input signal=1400 mV p-p differential, CAM clock = 1MHz CAM parameter settings Gain = 1 60 40 SNR[ dB] [dB] 20 0 SINAD[ dB] - 20 DISTN[ dB] - 40 - 60 - 80 - 100 - 120 0.7 1.4 2.8 3.5 5.6 7.0 INPUT [Vp-p] DS030100-U006a - 18 - AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O Power Supply Rejection Ratio (PSRR) Measurements The following plots give an indication of the PSRR for some representative CAMs. AVDD to Power Supply (PS): 5v +/- 0.25v sinusoidal waveform (100 kHz to 1 MHz) INPUT AMP PSRR [dB] INPUT LPF PSRR [dB] 80.00 80.00 70.00 70.00 60.00 60.00 50.00 50.00 40.00 40.00 30.00 30.00 20.00 20.00 DC 100 1KHz 10KHz 100KHz 1M Hz DC VMR, Vref+, Vref- 100.00 15 50 100 1KHz 10KHz 100KHz 1M Hz PSRR [dB] 90.00 PSRR_VMR [ dB] 80.00 PSRR_VREFP [ dB] 70.00 PSRR_VREFP [ dB] 60.00 50.00 40.00 30.00 20.00 DC 100 1KHz 10KHz 100KHz 1M Hz OUTPUT Voltage Mode + LPF PSRR [dB] 80.00 70.00 60.00 50.00 40.00 30.00 20.00 DC 100 1KHz 10KHz 100KHz GAININV_1MHz PSRR [dB] 1M Hz GAININV_4MHz PSRR [dB] 100 100 90 90 80 80 70 70 60 60 50 50 40 40 30 30 20 20 DC 50 100 1KHz 10KHz 100KHz 1M Hz 100 1KHz 10KHz 100KHz 1M Hz DS030100-U006a - 19 - AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O The following is provided for information only, as and when additional characterization data is collected ‘noise measurements’ will be added formally to the datasheet. Noise And Distortion Observations The following plots give an indication of the noise characteristics of Anadigm®’s AN221E04 FPAA device. These were done using a simple set-up and in many cases reflect the noise limit of the setup. Actual device noise margins are expected to be better. Signal and Noise for the Input Cell (input signal - 50mVp-p differential to the FPAA at 10 kHz) Signal to Noise: -92 dB, at 376KHz, 3Hz BW Input gain stage set at X16 Input anti-aliasing filter set off Input chopper amplifier set off Signal and Noise for the Output Cell (with a differential input 4V p-p, 660Hz) Signal to Noise: -106 dB, at 345KHz, 3Hz BW Voltage output mode (including filter) ON Output smoothing filter set at fC = 470 kHz DS030100-U006a - 20 - AN221E04 Datasheet – Dynamically Reconfigurable FPAA With Enhanced I/O Measured THD for input and output cells (with a differential input 4V p-p, 660Hz) Settings Distortion in dB Input cell with anti-aliasing filter set at fC = 470 kHz Output cell with differential to single ended converter and output smoothing filter set at fC = 470 kHz 81.6 82 Signal and Noise for a representative CAM – Gaininv CAM (input signal of 700mV p-p differential at 10 kHz) Signal to Noise: 108 dB, at 528 kHz, 3Hz BW THD for a representative CAM – Gaininv CAM (with a differential input 4V p-p, 660Hz) CAM Clock Frequency 250 KHz 1 MHz 2 MHz 4 MHz Distortion (dB) 80.00 72.83 69.22 73.48 As above, zoom to lower frequency DS030100-U006a - 21 -