PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF HYDIS A N D S H A L L N O T B E REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF HEI AND MUST BE RETURNED TO HYDIS UPON ITS REQUEST. TITLE: HT17E11-300 Preliminary Product Specification Rev. P1 Hyundai Display Technology, Inc. SPEC. NUMBER S864-1080 RASR 055-2 PRODUCT GROUP TFT-LCD PRODUCT REV. P1 ISSUE DATE JAN. 09, ‘02 PAGE 1 OF 22 A4 (210 X 297) PRODUCT GROUP REV. ISSUE DATE TFT-LCD PRODUCT P1 JAN. 09, ‘02 REVISION HISTORY REV. ECN NO. P0 P1 - SPEC. NUMBER S864-1080 RASR 056-1 DESCRIPTION OF CHANGES Initial Release Up-date optical specifications (page 7) DATE PREPARED DEC. 14, ‘01 K.C.CHO K.C.CHO JAN. 09, ‘02 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 2 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 Contents No. Item Page 1.0 General Description 4 2.0 Absolute Maximum Ratings 5 3.0 Electrical Specifications 6 4.0 Optical Specifications 7 5.0 Interface Connection 9 6.0 Signal Timing Specifications 11 7.0 Signal Timing Waveforms of interface signal (DE mode) 13 8.0 Input Signals, Display Colors & Gray Scale of Colors 14 9.0 Power Sequence 15 10.0 Mechanical Characteristics 16 11.0 Reliability Test 17 12.0 Handling & Cautions 18 13.0 Appendix 19 SPEC. NUMBER S864-1080 RASR 057-1 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 3 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 1.0 GENERAL DESCRIPTION 1.1 Introduction [HT17E11-300] is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 17.0 inch diagonally measured active area with SXGA resolutions (1280 horizontal by 1024 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16,194,227 colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type. CN21 CN22 LVDS Input Signal LVDS Rx + Timing Controller Power & Analog Block Gate Driver Connector (CN11) VDD Source Driver TFT LCD Panel 1280 ×1024 CN23 CN24 1.2 Features l LVDS Interface with 2 pixel / clock l High-speed response l Low power consumption l 8-bit color depth, display 16,194,227 colors l Incorporated edge type back-light (Four lamps) l High luminance and contrast ratio, low reflection and wide viewing angle l DE (Data Enable) mode only 1.3 Applications l Desktop Type of PC & Workstation Use l Slim-Size Display for Stand-alone Monitor l Display Terminals for Control System l Monitors for Process Controller SPEC. NUMBER S864-1080 RASR 057-1 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 4 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 1.4 General Specifications The followings are general specifications at the model [HT17E11-300]. <Table 1. General Specifications> Parameter Specification Unit Active area 337.92 (H) × 270.336(V) mm Number of pixels 1280(H) × 1024(V) pixels Pixel pitch 0.264(H) × 0.264(V) mm Pixel arrangement RGB Vertical stripe Display colors 16,194,227 Display mode Normally White Dimensional outline 383.5(H) × 306.0(V) × 21.0(D) typ. mm Weight 2,200 typ. gram Back-light Top/Bottom edge side 4-CCFL type Remarks colors Note 1 Note: 1. CCFL (Cold Cathode Fluorescent Lamp) 2.0 ABSOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. <Table 2. Absolute Maximum Ratings> Parameter [VSS = GND =0V] Symbol Min Max Unit Remarks Power Input Voltage VDD VSS-0.5 6.5 V Ta = 25℃ Logic Input Voltage VIN VSS-0.3 VDD+0.3 V Back-light Lamp Current IBL 3 7 mA Back-light lamp Frequency FL 40 (80) KHz Operating Temperature TOP 0 +50 ℃ (Humidity) RH 80 % Storage Temperature TST +60 ℃ (Humidity) RH 90 % SPEC. NUMBER S864-1080 RASR 057-1 -20 ≤ 40 ℃ ≤ 40 ℃ SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 5 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 3.0 ELECTRICAL SPECIFICATIONS < Table 3. Electrical specifications > Parameter [Ta = 25±2℃] Min Typ Max Unit Power Supply Voltage VDD 4.5 5.0 5.5 V Power Supply Current IDD - 560 1000 mA Permissible Input Ripple Voltage VRF 100 mV +100 mV High Level Differential Input Threshold Voltage Low Level Differential Input VIH - Note1 VDD = 5.0V Vcm = 1.2V typ. VIL -100 - Back-light Lamp Voltage VBL 680 710 840 Vrms Back-light Lamp Current IBL 3.0 6.0 7.0 mArms FL 40 - 60 KHz Note 2 1075 Vrms 25℃, Note 3 1310 Vrms 0℃ , Note 3 50000 hrs IBL = 6.0mA PD 2.8 W P BL 17.0 W P total 19.8 W Threshold Voltage Back-light Lamp operating Frequency mV Remarks Lamp Start Voltage Lamp Life Power Consumption 40000 IBL = 6.0mA, Note 4 Notes: 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for VDD = 5.0V, Frame rate= 60Hz and Clock frequency = 54MHz. Test Pattern of power supply current a) Typ: Vertical color bar pattern b) Max: Vertical 2 Skip lines pattern 2. The lamp frequency should be selected as different as possible from the horizontal synchronous frequency and its harmonics to avoid interference, which may cause line flow on the display 3. The voltage above this value should be applied to the lamps for more than 1 second to start-up. Otherwise the lamps may not be turned on. 4. Calculated value for reference (VBL × IBL) × 4 excluding inverter loss. SPEC. NUMBER S864-1080 RASR 057-1 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 6 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 4.0 OPTICAL SPECIFICATIONS 4.1 Overview The test of Optical specifications shall be measured in a dark room (ambient luminance ≤ 1 lux and temperature = 25±2°C) with the equipment of Luminance meter system (Goniometer system and TOPCONE BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and φ equal to 0°. We refer to θφ=0 (=θ3) as the 3 o’clock direction (the “right”), θφ=90 (=θ12) as the 12 o’clock direction (“upward”), θφ=180 (=θ9) as the 9 o’clock direction (“left”) and θφ=270 (=θ6) as the 6 o’clock direction (“bottom”). While scanning θ and/or φ, the center of the measuring spot on the display surface shall stay fixed. The measurement shall be executed after 30 minutes warm-up period. VDD shall be 5.0V +/- 10% at 25°C. Optimum viewing angle direction is 6 o’clock. 4.2 Optical Specifications [VDD=5.0V, Frame rate=60Hz, Clock=54MHz, IBL = 6.0mA, Ta = 25±2℃] Parameter Symbol Min Typ Max Unit 65 70 - Deg 65 70 - Deg 40 45 - Deg Θ6 60 65 - Deg Luminance contrast ratio CR 350 500 - Luminance of white YW - 250 - White luminance uniformity ΔY - - 1.2 xW 0.291 0.321 0.351 yW 0.308 0.338 0.368 Horizontal Θ3 Viewing Θ9 Angle Θ12 Vertical White Red Reproduction of color Green Blue Response time (Rise + Decay) Cross talk SPEC. NUMBER S864-1080 RASR 057-1 Condition CR > 10 Remark Note 1 Note 2 cd/m2 xR Θ = 0° 0.610 0.640 0.670 yR (Center) 0.317 0.347 0.377 xG Normal 0.272 0.302 0.332 yG Viewing 0.557 0.587 0.617 xB Angle 0.113 0.143 0.173 yB 0.069 0.099 0.129 Ttotal - 20 CT - - 2.0 Note 3 Note 4 Note 5 msec Note 6 % Note 7 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 7 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 Note: 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface (See FIGURE 1 shown in Appendix). 2. Contrast measurements shall be made at viewing angle of θ= 0° and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically. CR = 3. 4. 5. 6. 7. Luminance when displaying a white raster Luminance when displaying a black raster Center Luminance of white is defined as the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display. The White luminance uniformity on LCD surface is then expressed as : ΔY = Maximum Luminance of five points / Minimum Luminance of five points (See FIGURE 2 shown in Appendix). The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. The electro-optical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the “data” input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Td, and 90% to 10% is Tr. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark. (See FIGURE 4 shown in Appendix). SPEC. NUMBER S864-1080 RASR 057-1 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 8 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 5.0 INTERFACE CONNECTION 5.1 Electrical Interface Connection l CN11: Module Side Connector : FI-X30S-HF (JAE) User Side Connector : FI-X30H-HF (JAE) or equivalent Pin No Symbol 1 RXO0- LVDS ODD 0 – SIGNAL 2 RXO0+ LVDS ODD 0 + SIGNAL 3 RXO1- LVDS ODD 1 – SIGNAL 4 RXO1+ LVDS ODD 1 + SIGNAL 5 RXO2- LVDS ODD 2 – SIGNAL 6 RXO2+ LVDS ODD 2 + SIGNAL 7 GND GROUND 8 RXOCLK- LVDS ODD CLOCK – SIGNAL 9 RXOCLK+ LVDS ODD CLCOK + SIGNAL 10 RXO3- LVDS ODD 3 – SIGNAL 11 RXO3+ LVDS ODD 3 + SIGNAL 12 RXE0- LVDS EVEN 0 – SIGNAL 13 RXE0+ LVDS EVEN 0 + SIGNAL 14 GND GROUND 15 RXE1- LVDS EVEN 1 – SIGNAL 16 RXE1+ LVDS EVEN 1 + SIGNAL 17 GND GROUND 18 RXE2- LVDS EVEN 2 – SIGNAL 19 RXE2+ LVDS EVEN 2 + SIGNAL 20 RXECLK- LVDS EVEN CLOCK – SIGNAL 21 RXECLK+ LVDS EVEN CLOCK + SIGNAL 22 RXE3- LVDS EVEN 3 – SIGNAL 23 RXE3+ LVDS EVEN 3 + SIGNAL 24 GND GROUND 25 NC NO CONECTION 26 DE DE OUT 27 NC NO CONECTION 28 VDD 29 VDD 30 VDD SPEC. NUMBER S864-1080 RASR 057-1 Function Remark POWER SUPPLY (+5.0V) SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 9 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 5.2 LVDS Interface (Tx : THC63LVDM83A or Equivalent) O D D L V D S E V E N L V D S Input signal OR0 OR1 OR2 OR3 OR4 OR5 OG0 OG1 OG2 OG3 OG4 OG5 OB0 OB1 OB2 OB3 OB4 OB5 HSYNC VSYNC DE MCLK OR6 OR7 OG6 OG7 OB6 OB7 RSVD ER0 ER1 ER2 ER3 ER4 ER5 EG0 EG1 EG2 EG3 EG4 EG5 EB0 EB1 EB2 EB3 EB4 EB5 HSYNC VSYNC DE MCLK ER6 ER7 EG6 EG7 EB6 EB7 RSVD SPEC. NUMBER S864-1080 RASR 057-1 Transmitter Pin No Pin No 51 52 54 48 55 47 56 3 4 6 7 11 46 12 45 14 15 19 20 22 23 42 24 41 27 28 30 31 40 39 50 2 8 38 10 37 16 18 25 51 52 54 48 55 47 56 3 4 6 7 11 46 12 45 14 15 19 20 22 23 42 24 41 27 28 30 31 40 39 50 2 8 38 10 37 16 18 25 Interface System (Tx) TFT-LCD (Rx) FI-X30S-HF Pin No. OUT0OUT0+ RXO0RXO0+ 1 2 OUT1OUT1+ RXO1RXO1+ 3 4 OUT2OUT2+ RXO2RXO 2+ 5 6 CLKOUTCLKOUT+ RXO CLKRXO CLK+ 8 9 OUT3+ OUT3- RXO 3RXO 3+ 10 11 OUT0OUT0+ RXE0RXE 0+ 12 13 OUT1OUT1+ RXE 1RXE 1+ 15 16 OUT2OUT2+ RXE 2RXE 2+ 18 19 CLKOUTCLKOUT+ RXE CLKRXE CLK+ 20 21 OUT3+ OUT3- RXE 3RXE 3+ 22 23 SPEC. TITLE HT17E11-300 Preliminary Product Specification Remark PAGE 10 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 5.3 Data Input Format ODD EVEN (1,1) (2,1) ISSUE DATE JAN. 09, ‘02 (1279,1) (1280,1) RGBRGB RGBRGB 1 Pixel = 3 Dots RG B RGBRGB (1,1024) (2,1024) RGBRGB (1279,1024) (1280,1024) Display Position of Input Data (V-H) 5.4 Back-light Interface Connection l CN21, 22, 23, 24: Module side connector User side connector Pin No : BHSR-02VS-1 (JST) : SM02B-BHSS-1-TB (JST) or equivalent INPUT 1 2 HOT COLD Color Function Pink White High voltage Ground 6.0 SIGNAL TIMING SPECIFICATIONS 6.1 The [HT17E11-300] is operated by the only DE (Data enable) mode (LVDS Transmitter Input) Item Symbols Frequency Clock High Time Low Time Setup Time Data Hold Time Data Enable Setup Time Frame Period Vertical Display Period One Line Scanning Period Horizontal Display Period SPEC. NUMBER S864-1080 RASR 057-1 1/Tc Tch Tcl Tds Tdh Tes Tv Tvd Th Thd Min 5 5 4 4 4 1032 672 640 Typ 54 1066 1024 844 640 Max 68 2044 1022 640 SPEC. TITLE HT17E11-300 Preliminary Product Specification Unit MHz ns ns ns ns ns lines lines clocks clocks PAGE 11 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 6.2 LVDS Rx interface timing parameter The specification of the LVDS Rx interface timing parameter is shown in Table 4. < Table 4. LVDS Rx Interface Timing Specification> Symbol Min Typ Max Item CLKIN Period CLK Difference Input Data 0 Input Data 1 Input Data 2 Input Data 3 Input Data 4 Input Data 5 Input Data 6 tRCIP tCdiff tRIP1 tRIP0 tRIP6 tRIP5 tRIP4 tRIP3 tRIP2 Unit 14.7 TBD -0.2 18.5 0 0 TBD +0.2 1*tRICP/7-0.2 1*tRICP/7 1*tRICP/7+0.2 2*tRICP/7-0.2 2*tRICP/7 2*tRICP/7+0.2 3*tRICP/7-0.2 3*tRICP/7 3*tRICP/7+0.2 4*tRICP/7-0.2 4*tRICP/7 4*tRICP/7+0.2 5*tRICP/7-0.2 5*tRICP/7 5*tRICP/7+0.2 6*tRICP/7-0.2 6*tRICP/7 6*tRICP/7+0.2 Remark nsec nsec nsec nsec nsec nsec nsec nsec nsec TRIP2 tRIP3 tRIP4 tRIP5 tRIP6 tRIP0 tRIP1 RXO/Ez +/* Z=0, 1, 2, 3 RXOCLK+ RXECLK+ Rx3 Rx2 Rx1 Rx0 Rx6 Vdiff=0[v] Rx5 Rx4 Rx3 Rx2 Rx1 Rx0 Vdiff=0[v] tRCIP tCdiff * Vdiff = (RXO/Ez+)-(RXO/Ez-), ….. , (RXO/ECLK+)-(RXO/ECLK-) SPEC. NUMBER S864-1080 RASR 057-1 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 12 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 7.0 SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL (DE MODE) 7.1 Vertical Timing Waveforms Tv Tvd MCLK Th ENAB R7 ~ R0 G7 ~ G0 B7 ~ B0 Invalid Data x,1 x,2 x,1024 x,y Invalid Data x+1,1 7.2 Horizontal Timing Waveforms Th Thd MCLK Tc ENAB RA7 ~RA0 GA7 ~GA0 BA7 ~BA0 D1 D2 D638 Dn Tch D639 D640 Invalid Data D1 D2 D3 Tcl 2.0V 1.5V MCLK Data Tds Tdh Valid Data 0.8V 2.0V 0.8V Tes ENAB SPEC. NUMBER S864-1080 RASR 057-1 2.0V SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 13 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF COLORS Colors & Gray Scale Basic Colors Gray Scale Of Red Gray Scale Of Green Gray Scale Of Blue Gray Scale Of White & Black Red data Black Blue Green Cyan Red Magenta Yellow White Black △ Darker △ ▽ Brighter ▽ Red Black △ Darker △ ▽ Brighter ▽ Green Black △ Darker △ ▽ Brighter ▽ Blue Black △ Darker △ ▽ Brighter ▽ White SPEC. NUMBER S864-1080 RASR 057-1 Green data Blue data R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 ↓ ↓ 1 1 1 1 1 1 0 0 0 0 0 0 ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 ↓ ↓ 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 1 0 0 0 0 1 1 1 1 0 1 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 1 1 1 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 ↓ ↓ 1 1 1 1 1 1 0 0 0 0 0 0 ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 ↓ ↓ 1 1 1 1 1 1 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 1 0 1 0 0 0 1 0 0 0 0 1 0 1 0 0 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 1 1 1 0 1 1 1 1 1 1 1 1 1 1 SPEC. TITLE HT17E11-300 Preliminary Product Specification 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 0 0 0 ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 ↓ ↓ 1 1 1 1 1 1 0 0 0 0 0 0 ↓ ↓ 1 1 1 1 1 1 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 1 1 1 0 0 0 0 1 1 0 0 1 1 0 1 0 1 0 1 1 1 0 1 1 1 0 1 PAGE 14 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 9.0 POWER SEQUENCE To prevent a latch-up or DC operation of the LCD module, the power on/off sequence should be as shown in below 0.9VDD Power Supply 0.9VDD 0.1VDD 0.1VDD 0V T1 T2 T5 T6 Valid Interface Signal 0V T3 Back- light l l l l l l T4 0V 0 < T1 ≤ 5 ms 20 ms < T2 ≤ 50 ms 500 ms ≤ T3 100 ≤ T4 0 < T5 ≤ 50 ms 1 sec ≤ T6 Notes: 1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. 3. Back Light must be turn on after power for logic and interface signal are valid. SPEC. NUMBER S864-1080 RASR 057-1 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 15 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 10.0 MECHANICAL CHARACTERISTICS 10.1 Dimensional Requirements FIGURE 6 shown in appendix shows mechanical outlines for the model [HT17E11-300]. Other parameters are shown in Table 5. <Table 5. Dimensional Parameters> Parameter Specification Active area 337.92 (H) × 270.336(V) Number of pixels 1280(H) × 1024(V) Unit mm pixels (1 pixel = R + G + B dot) Pixel pitch 0.264(H) × 0.264(V) Pixel arrangement RGB Vertical stripe Display colors 16,194,227 Display mode Normally white Dimensional outline 383.5 (H) × 306.0 (V) × 21.0 (D) mm Weight 2,200 typ. gram Back-light Top / Bottom edge side 4-CCFL type mm colors 10.2 Mounting See FIGURE 5 shown in appendix 10.3 Anti-Glare and Polarizer Hardness. The surface of the LCD has an anti-glare coating to minimize reflection and a coating to reduce scratching. 10.4 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50[cm] from the screen with an overhead light level of 350[lux]. The manufacture shall furnish limit samples of the panel showing the lightest leakage acceptable. SPEC. NUMBER S864-1080 RASR 057-1 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 16 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 11.0 RELIABILITY TEST The Reliability test items and its conditions are shown in below. <Table 6. Reliability Test Parameters> No Test Items Conditions 1 High temperature storage test Ta = 60 °C, 240 hrs 2 Low temperature storage test Ta = -20 °C, 240 hrs High temperature & high humidity 3 operation test Ta = 50 °C, 80 %RH, 240 hrs 4 High temperature operation test Ta = 50 °C, 240 hrs 5 Low temperature operation test Ta = 0 °C, 240 hrs 6 Thermal shock Ta = -20 °C ↔ 60 °C (30 min), 100 cycle Frequency : 10 ~ 300 Hz, Sweep rate 30min Gravity/AMP : 1.5G Period : ±X, ±Y, ±Z 30min Gravity : 70G Pulse width : 11ms, sine wave Vibration test 7 (non-operating) Shock test 8 (non-operating) 9 ±X, ±Y, ±Z Once for each direction Air : 150 pF, 330Ω, 15KV Contact : 150 pF, 330Ω, 8KV Electrostatic discharge test SPEC. NUMBER S864-1080 RASR 057-1 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 17 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 12.0 HANDLING & CAUTIONS 12.1 Cautions when taking out the module Ÿ Pick the pouch only, when taking out module from a shipping package. 12.2 Cautions for handling the module Ÿ As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. Ÿ As the LCD panel and back-light element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. Ÿ As the surface of the polarizer is very soft and easily scratched, use a soft dry-cloth without chemicals for cleaning. Ÿ Do not pull the interface connector in or out while the LCD module is operating. Ÿ Put the module display side down on a flat horizontal plane. Ÿ Handle connectors and cables with care. 12.3 Cautions for the operation Ÿ When the module is operating, do not lose LVDS signals. If any one of these signals were lost, the LCD panel would be damaged. Ÿ Obey the supply voltage sequence. If the wrong sequences were applied, the module would be damaged. 12.4 Cautions for the atmosphere Ÿ Dewdrop atmosphere should be avoided. Ÿ Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer-packing pouch and under relatively low temperature atmosphere is recommended. 12.5 Cautions for the module characteristics Ÿ Do not apply fixed pattern data signal to the LCD module at aging time. Ÿ Applying fixed pattern for a long time may cause image sticking. 12.6 Other cautions Ÿ Do not disassemble and/or re-assemble LCD module. Ÿ Do not re-adjust variable resistor or switch etc. Ÿ When returning the module for repair or etc, please pack the module not to be broken. We recommend on using the original shipping packages. SPEC. NUMBER S864-1080 RASR 057-1 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 18 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 13.0 APPENDIX Figure 1. Measurement Set Up Figure 2. Locations Average Luminance Measurement Locations & Uniformity Measurement Column Row 320 2 256 512 640 960 3 1 4 5 768 SPEC. NUMBER S864-1080 RASR 057-1 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 19 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 Figure 3. Response Time Testing TFT Off(White) TFT On(Black) TFT Off(White) Td Tr 100% 90% 10% 0% Figure 4. Cross Modulation Test Description VIEW AREA VIEW AREA 960, 256 320, 256 320, 768 YA (1120, 512) Cross-Talk = 960, 768 YB (1120, 512) YB - YA YA × 100 Where: YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m2) The location measured will be exactly the same in both patterns. SPEC. NUMBER S864-1080 RASR 057-1 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 20 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 Figure 5. TFT-LCD Module Outline Dimensions (Front view) SPEC. NUMBER S864-1080 RASR 057-1 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 21 OF 22 A4 (210 X 297) PRODUCT GROUP REV. TFT-LCD PRODUCT P1 ISSUE DATE JAN. 09, ‘02 Figure 6. TFT-LCD Module Outline Dimensions (Rear view) SPEC. NUMBER S864-1080 RASR 057-1 SPEC. TITLE HT17E11-300 Preliminary Product Specification PAGE 22 OF 22 A4 (210 X 297)