TITLE : HX121WX1-100 Preliminary Product

PROPRIETARY NOTE
THIS SPECIFICATION IS THE PROPERTY OF BOE HYDIS AND SHALL NOT
BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF
BOE HYDIS AND MUST BE RETURNED TO BOE HYDIS UPON ITS REQUEST
TITLE : HX121WX1-100
Preliminary Product Specification
Rev. P2
FOR MORE INFORMATION:
AZ DISPLAYS, INC.
75 COLUMBIA, ALISO VIEJO, CA, 92656
Http://www.AZDISPLAYS.com
BOE HYDIS TECHNOLOGY
SPEC. NUMBER
B2005-C001-A (1/3)
PRODUCT GROUP
TFT LCD
REV.
P2
ISSUE DATE
2008. 01. 14
PAGE
1 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
DATE
PREPARED
REVISION HISTORY
REV.
ECN NO.
DESCRIPTION OF CHANGES
P0
ƒ Initial Release
‘07. 08. 08
H. R. Park
P1
-.Add the surface treatment_AR(4page)
-.Add the life time test condition (8page)
-.Add the color reproduction(9page)
-.Change the reflectance(9page)
’07. 08. 10
H. R. Park
P2
-.Change the Power Consumption, CR, Gamut,
Chromaticity, Reflectance
’08. 01. 14
H. R. Park
SPEC. NUMBER
SPEC TITLE
B2005-C001-A (2/3)
HX121WX1-100 Pre-Product Specification
PAGE
2 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
Contents
No
Item
Page
1.0
General Description
4
2.0
Absolute Maximum Ratings
6
3.0
Electrical Specifications
7
4.0
Optical Specifications
9
5.0
Interface Connections
14
6.0
Signal Timing Specifications
17
7.0
Signal Timing Waveforms
17
8.0
Input Signals, Basic Display Colors & Gray Scale of Colors
19
9.0
Power Sequence
20
10.0
Mechanical Characteristics
21
11.0
Mechanical Drawing
22
12.0
Reliability Test
25
13.0
Handling & Cautions
25
14.0
Labels
27
15.0
Packing Information
28
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
3 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
1.0 GENERAL DESCRIPTION
1.1 Introduction
HX121WX1-100 is a color active matrix TFT LCD module using amorphous silicon TFT's
(Thin Film Transistors) as an active switching devices. This module has a 12.1 inch
diagonally measured active area with WXGA resolutions (1280 horizontal by 800 vertical
pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in
vertical Stripe and this module can display 262,144 colors. The TFT-LCD panel used for this
module is a low reflection and higher color type.
Source Driver
LVDS
Input
Signal
LVDS Rx
+
T/CON
Gate Driver
1 (CN
Connector
DC/DC
Gamma
Vcom
VDD
TFT LCD Panel
BACK LIGHT (Fluorescent Lamp)
1280 ×800
1
)
HVDD
VDIM
LED Driver
Back Light (SMD LED Array)
CN2
1.2 Features
z Thin and Light Weight
z 3.3 V Logic Power Supply
z 12V Back-light Power Supply
z 1 Channel LVDS Interface
z SMD LED (48EA) Array (Bottom Side/Horizontal Direction)
z 262,144 Colors
z Data Enable Signal Mode
z Side Mounting Frame
z Green Product (RoHS)
z Anti-Reflection polarizer product for sunlight readability
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
4 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
1.3 Application
z Tablet PC (Wide type)
1.4 General Specifications
Parameter
Specification
Active area
261.12(H) ×163.20(V)
Number of pixels
1280(H) ×800(V)
Pixel pitch
0.204(H) ×0.204(V)
Pixel arrangement
RGB Vertical Stripe
Display colors
262,144
Display mode
Normally Black
Outline dimension
276.8±0.3(H) ×180.0±0.3(V) ×6.8(D:Max.)
Weight
265(Typ.) / 275(Max.)
Back-light
SMD LED (48EA) Array
Surface treatment
Anti-Reflection, 2H
Unit
Remarks
mm
pixels
mm
colors
mm
Note 1
g
Note 2
Note 1 : At PCB side (LED Side: 4.6mm Max.)
Note 2 : Without digitizer
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
5 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
2.0 ABSOLUTE MAXIMUM RATINGS
The followings are maximum values which, if exceed, may cause faulty operation or
damage to the unit.
Ta=25+/-2°C
Parameter
Symbol
Min.
Max.
Unit
Logic Power Supply Voltage
VDD
-0.3
4.0
V
Logic Power Supply Voltage
VIN
-0.3
VDD+0.3
V
HVDD
-0.3
40
V
Back-light LED Current
ILED
-
30
mA
Back-light LED Reverse Voltage
VR
-
5
V
Operating Temperature
TOP
0
+50
℃
Storage Temperature
TSP
-20
+60
℃
Back-light Power Supply Voltage
Remarks
Note 1
Note 1, Note 2
Note 1. Ambient temperature vs allowable forward current are shown in the figure below.
Note 2. Temperature and relative humidity range are shown in the figure below.
90% RH Max. ( 40℃ ≥ Ta)
Maximum wet - bulb temperature at 39℃ or less. ( > 40℃) No condensation.
Relative Humudity
100
(40, 90)
90
80
60
Operating Range
(50, 50)
40
(60, 27)
20
Storage Range
5
-40
-20
0
20
40
60
80
Temperature (℃)
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
6 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
3.0 ELECTRICAL SPECIFICATIONS
3.1 Electrical Specifications
< Table 3. Electrical Specifications >
Parameter
Min.
Typ.
Max.
Unit
Remarks
Logic Power Supply Voltage
VDD
3.0
3.3
3.6
V
Note 1
Logic Power Supply Current
IDD
-
364
TBD
mA
Note 1
Back-light Power Supply Voltage
HVDD
7.0
12.0
20
V
Note 2
Back-light Power Supply Current
IHVDD
-
255
305
mA
Note 2, 3
Back-light Power Consumption
PBL
-
3.06
3.66
W
Note 2, 3
LED Driver’s Efficiency
η
-
82
-
%
Note 2, 3
Back-light PWM Frequency
FPWM
200
280
350
㎐
High Level PWM Signal Voltage
VPWMH
2.1
3.3
5.0
V
Low Level PWM Signal Voltage
VPWML
-
0
0.6
V
High Level Differential Input Signal
Voltage
VIH
-
-
+100
mV
Low Level Differential Input Signal
Voltage
VIL
-100
-
-
mV
Back-light LED Voltage /
Back-light LED Total Voltage
VLED
/VBL
-
3.1
/ 37.2
3.5/
42.0
V
Note 4
Back-light LED Current /
Back-light LED Total Current
ILED
/IBL
-
16.9
/ 67.6
17.8/7
1.2
mA
Note 4
10,000
-
-
Hrs
Note 6
PD
0.95
TBD
PLED
0.50
0.88
Ptotal
1.45
TBD
Life Time
EBL (Extended Battery Life)
Power Consumption
SPEC. NUMBER
B2005-C001-A (3/3)
VCM = 1.2V
Note 1, 2, 3
PD
-
1.0
TBD
W
Note 1
PLED
-
2.51
2.99
W
Note 4
Ptotal
-
3.51
TBD
W
Note 1, 4
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
7 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
Notes : 1. The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for 3.3V at 25℃.
a) Typ : Window XP pattern,
b) Max : Vertical Sub line pattern
c) EBL : Mosaic pattern ( 32 X 32 )
2. The power supply voltage and current is measured and specified at the interface
connector of LCM including LED Driver.
3. Reference value, which is measured with LED Driver for 12V.
4. Reference value, which is measured without LED Driver.
5. Calculated value for reference (VLED × ILED × # of LEDs (48EA) ).
6. End of Life shall be determined by the time when any of the following is satisfied
under continuous lighting at 25℃ and ILED = 16.9mA.
-. Intensity drops to 50% of the Initial Value (Luminance Spec.)
-. Based on LED
3.2 PWM Duty Ratio vs Brightness
100
Relative Brightness (%)
90
80
70
60
50
40
30
20
10
0
0
10
20
30
40
50
60
70
80
90
100
Duty Ratio (%)
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
8 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
4.0 OPTICAL SPECIFICATIONS
4.1 Overview
The test of optical specifications shall be measured in a dark room (ambient luminance ≤ 1
lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer
system and TOPCON BM-5A) and test unit shall be located at an approximate distance
50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to θØ=0
(=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction
(“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) and θØ=270(= θ6 ) as the 6
o’clock direction (“bottom”). While scanning θ and/or Ø, the center of the measuring spot on
the Display surface shall stay fixed. The backlight should be operating for 30 minutes prior to
measurement. VDD shall be 3.3+/- 0.3V at 25°C. Optimum viewing angle direction is 6
o’clock.
4.2 Optical Specifications
<Table 4. Optical Specifications>
Parameter
Viewing Angle
Range
Symbol
Horizontal
Vertical
Luminance Contrast Ratio
Luminance of
5 Points
White
5 Points
White
Luminance
13 Points
Uniformity
White
Color
Chromaticity
Red
Green
Blue
Color Reproduction
Response
Time
Cross Talk
Brightness
Outdoor
Spec.
Reflectance
SPEC. NUMBER
B2005-C001-A (3/3)
Min.
Typ.
500
90
90
90
90
700
-
Deg.
Deg.
Deg.
Deg.
Yw
250
300
-
cd/m2
ΔY5
80
-
-
ΔY13
60
-
-
Wx
Wy
Rx
Ry
Gx
Gy
Bx
By
0.273
0.289
0.540
0.333
0.304
0.525
0.109
0.097
0.313
0.329
0.580
0.373
0.344
0.565
0.149
0.137
42
0.353
0.369
0.620
0.413
0.384
0.605
0.189
0.177
-
30
-
ms
Note 5
3.0
500
3.5
2.0
-
%
ms
%
Note 6
Note 7
Note 8
Θ3
Θ9
Θ12
Θ6
CR
Total
(Tr + Td)
CT
Center
Ri
Condition
CR > 10
Θ = 0°
Ta= 25° C
Θ = 0°
Θ = 0°
Θ = 0°
SPEC TITLE
HX121WX1-100 Pre-Product Specification
Max.
Unit Remarks
Note 1
Note 2
%
Note 3
Note 4
%
PAGE
9 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
Note : 1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined
for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to
the optical axis which is normal to the LCD surface (see FIGURE 1 shown in page 11).
2. Contrast measurements shall be made at viewing angle of Θ= 0° and at the center of the LCD
surface. Luminance shall be measured with all pixels in the view field set first to white, then to the
dark (black) state. (See FIGURE 1 shown in page 11)
Luminance Contrast Ratio (CR) is defined mathematically.
CR =
Luminance when displaying a white raster
Luminance when displaying a black raster
3. The White luminance uniformity on LCD surface is then expressed.
(See FIGURE 2~3 shown in page 12)
Uniformity ΔY =
Minimum Luminance of 5(or 13) points
Maximum Luminance of 5(or 13) points
X 100 (%)
4. The color chromaticity coordinates specified in Table 4 shall be calculated from the spectral data
measured with all pixels first in red, green, blue and white. Measurements shall be made at the
center of the panel.
5. The electro-optical response time measurements shall be made as FIGURE 4 shown in page 13 by
switching the “data” input signal OFF and ON. The times needed for the luminance to change from
10% to 90% is Tr, and 90% to 10% is Td. (See FIGURE 4 shown in page 13)
6. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance
(YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of
that same area when any adjacent area is driven dark. (See FIGURE 5 shown in page 13)
7. Measure condition: Light source is 5,000nits, 15 degree position & BLU on
(See FIGURE 1 shown in page 11)
8. Reference : Standard White Plate (BaSO4)
Reflectance =
Light intensity of the reflected light on LCD Module
Output intensity of the reflected light on Reference
× 100%
Measure condition: Light source is 5,000nits, 15 degree position & BLU off
(See FIGURE 1 shown in page 11)
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
10 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
4.3 Optical Measurements
Figure 1. Measurement Set Up
(L = 5 0 c m )
<Indoor>
30º
Detector
Light Source (Halogen Lamp)
50cm
15cm
Module (BL on & off)
<Outdoor>
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
11 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
Figure 2. White Luminance and Uniformity Measurement Locations (5 points)
Column
320
640
960
Row
200
400
600
Note.
Luminance of white is defined as luminance values of 5 points across the LCD
surface. Luminance shall be measured with all pixels in the view field set first to
white. This measurement shall be taken at the locations shown in Figure 2 for a
total of the measurements per display.
* Yw = (Sum of 5 Points Luminance / 5 )
Figure 3. Uniformity Measurement Locations (13 points)
200
400
600
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
12 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
Figure 4. Response Time Testing
TFT Off(Black)
TFT On(White)
TFT Off(Black)
Td
Tr
100%
90%
10%
0%
Figure 5. Cross Modulation Test Description
VIEW AREA
VIEW AREA
320,200
960,200
L31
YB(1120, 400)
320,600
L0
YA (1120, 400)
Cross-Talk (%) =
960,600
YB - Y A
× 100
YB
Where:
YA = Initial luminance of measured area (cd/m2)
YB = Subsequent luminance of measured area (cd/m2)
The location measured will be exactly the same in both patterns
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
13 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
5.0 INTERFACE CONNECTIONS
5.1 Electrical Interface Connection
CN1
Interface Connector (FI-JH40S-HF10, Manufactured by JAE)
Pin No.
Symbol
GROUND
21
GND6
Connector Test
22
RCLKIN-
LVDS Negative clock signal (-)
LVDD1
Logic Power Supply : +3.3V
23
RCLKIN+
LVDS Positive clock signal (+)
4
LVDD2
Logic Power Supply : +3.3V
24
GND7
GROUND
5
LVDD3
Logic Power Supply : +3.3V
25
VDIM
PWM Brightness Control
6
VDD_DEID
EDID Power Supply : +3.3V
26
Reserved
NON-CONNECTION
7
TEST
NON-CONNECTION
27
Reserved
NON-CONNECTION
8
CLK_EDID
EDID Clock
28
HVGND1
GROUND
9
DATA_EDID
EDID Data
29
HVGND2
GROUND
10
GND2
GROUND
30
HVGND3
GROUND
11
GND3
GROUND
31
HVGND4
GROUND
12
NC
NON-CONNECTION
32
HVGND5
GROUND
13
RIN0-
LVDS Negative data signal (-)
33
NC
14
RIN0+
LVDS Positive data signal (+)
34
HVDD1
Back-light Power Supply: +12V
15
GND4
GROUND
35
HVDD2
Back-light Power Supply: +12V
16
RIN1-
LVDS Negative data signal (-)
36
HVDD3
Back-light Power Supply: +12V
17
RIN1+
LVDS Positive data signal (+)
37
HVDD4
Back-light Power Supply: +12V
18
GND5
GROUND
38
HVDD5
Back-light Power Supply: +12V
19
RIN2-
LVDS Negative data signal (-)
39
CONNTST
20
RIN2+
LVDS Positive data signal (+)
40
GND8
Pin No.
Symbol
1
GND1
2
CONNTST
3
Function
Function
GROUND
NON-CONNECTION
Connector Test
GROUND
Note 1. Connected with No. 2 & 39
Note 2. Start from left side
PCB
#1
#40
CN1 (FI-JH40S-HF10)
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
14 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
5.2 LVDS Interface
LVDS Transmitter : THC63LVDM83A
Transmitter
Input
signal
Pin No
R0
51
R1
52
R2
54
R3
55
R4
56
R5
3
G0
4
G1
6
G2
7
G3
11
G4
12
G5
14
B0
15
B1
19
B2
20
B3
22
B4
23
B5
24
HSYNC
27
VSYNC
28
DE
30
MCLK
31
SPEC. NUMBER
B2005-C001-A (3/3)
Pin No
Interface
FI-JH40SHF10
System (Tx)
TFT-LCD (Rx)
48
47
OUT0OUT0+
IN0IN0+
13
14
46
45
OUT1OUT1+
IN1IN1+
16
17
42
41
OUT2OUT2+
IN2IN2+
19
20
40
CLKOUT-
CLKIN-
22
39
CLKOUT+
CLKIN+
23
SPEC TITLE
HX121WX1-100 Pre-Product Specification
Remark
Pin No.
PAGE
15 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
5.3 Back-light Interface
CN2
LED FPC Connector (04-6298-009, Manufactured by Kyocera)
Pin No.
Symbol
Function
1
Anode1
LED Anode Power Supply
2
Anode2
LED Anode Power Supply
3
Anode3
LED Anode Power Supply
4
Anode4
LED Anode Power Supply
5
NC
6
Cathode1
LED Cathode Power Supply
7
Cathode2
LED Cathode Power Supply
8
Cathode3
LED Cathode Power Supply
9
Cathode4
LED Cathode Power Supply
Remark
LED Anode Power Supply
(3.25V X 12EA = 39V)
Non-Connection
LED Cathode Power Supply
5.4 Data Input Format
(1,1) (2,1)
(1279,1)(1280,1)
R G B R G B
R G B R G B
1 Pixel = 3 Dots
R G B
R G B R G B
(1,800) (2,800)
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
R G B R G B
(1279,800)(1280,800)
PAGE
16 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
6.0. SIGNAL TIMING SPECIFICATIONS
6.1 The 12.1” WXGA LCM is operated by the only DE (Data enable) mode
(LVDS Transmitter Input)
Item
Symbol
Min.
Typ.
Max.
Unit
Frame Period
T1
810
823
-
Lines
Vertical Display Period
T2
-
800
-
Lines
One line Scanning Period
T3
1350
1440
-
Clocks
Horizontal Display Period
T4
-
1280
-
Clocks
1/T5
-
69.3
-
MHz
Clock Frequency
7.0 SIGNAL TIMING WAVEFORMS
7.1 Timing Waveforms of Interface Signal
T1
T2
DE
T3
DCLK
T5
T4
DE
DATA
SIGNALS
SPEC. NUMBER
B2005-C001-A (3/3)
Valid display data (1280 Clocks)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
17 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
7.2 LVDS Rx Interface Timing Parameter
The specification of the LVDS Rx interface timing parameter
< LVDS Rx Interface Timing Specification>
Item
Symbol
Min.
Typ.
Max.
Unit Remarks
CLKIN Period
tRCIP
12.50
14.43
25.00
nsec
Input Data 0
tRIP0
-0.4
0.0
+0.4
nsec
Input Data 1
tRIP1
tRICP/7-0.4
tRICP/7
tRICP/7+0.4
nsec
Input Data 2
tRIP2
2 ×tRICP/7-0.4 2 ×tRICP/7 2 ×tRICP/7+0.4 nsec
Input Data 3
tRIP3
3 ×tRICP/7-0.4 3 ×tRICP/7 3 ×tRICP/7+0.4 nsec
Input Data 4
tRIP4
4 ×tRICP/7-0.4 4 ×tRICP/7 4 ×tRICP/7+0.4 nsec
Input Data 5
tRIP5
5 ×tRICP/7-0.4 5 ×tRICP/7 5 ×tRICP/7+0.4 nsec
Input Data 6
tRIP6
6 ×tRICP/7-0.4 6 ×tRICP/7 6 ×tRICP/7+0.4 nsec
tRIP6
tRIP5
tRIP4
tRIP3
tRIP2
tRIP1
tRIP0
RxINz +/* Z = 0, 1, 2
Rx
RxCLKIN+/-
Rx
Rx
Rx
Rx
Rx
Rx
Rx
Vdiff=0[v]
Rx
Rx
Rx
Vdiff=0[v]
tRCIP
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
18 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
8.0 INPUT SIGNALS, BASIC DISPLAY COLORS & GRAY SCALE OF
COLORS
Each color is displayed in sixty-four gray scales from a 6 bit data signal input. A total of
262,144 colors are derived from the resultant 18 bit data.
Colors & Gray
Scale
Black
Blue
Green
Basic
Cyan
Colors
Red
Magenta
Yellow
White
Black
△
Darker
Gray
△
Scale
Of
▽
Red
Brighter
▽
Red
Black
△
Darker
Gray
△
Scale
Of
▽
Green
Brighter
▽
Green
Black
△
Darker
Gray
△
Scale
Of
▽
Blue
Brighter
▽
Blue
Black
△
Gray
Darker
Scale
△
Of
White
▽
&
Brighter
Black
▽
White
SPEC. NUMBER
B2005-C001-A (3/3)
Red Data
Green Data
R5
R4
R3
R2
R1
R0
G5
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
1
1
1
1
0
0
1
0
0
0
0
1
1
1
1
0
1
0
0
0
1
1
0
0
1
1
0
0
0
0
0
1
1
0
0
1
1
0
0
0
0
0
1
1
0
0
1
1
0
0
0
↓
↓
1
1
1
0
0
0
1
1
1
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
1
1
1
0
0
0
1
1
1
1
1
1
0
0
1
1
0
0
1
1
0
0
0
0
1
0
1
0
1
0
1
0
0
0
0
1
0
1
0
1
0
1
0
0
0
0
1
0
1
0
1
0
1
0
0
0
0
0
0
0
0
1
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
1
1
1
1
1
1
1
1
1
1
0
1
0
1
0
1
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
0
1
1
1
0
0
0
0
1
1
0
0
1
1
0
1
0
1
0
1
1
1
0
1
1
1
0
1
↓
↓
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
0
1
1
1
0
0
0
1
1
1
0
0
0
1
1
1
0
0
0
↓
↓
1
1
1
0
1
0
1
0
1
0
1
0
0
0
↓
↓
↓
↓
0
0
0
0
0
0
0
1
0
1
0
1
0
1
0
0
0
↓
↓
0
0
0
0
0
0
1
1
1
0
0
0
↓
↓
1
1
1
0
0
1
1
0
0
1
1
0
0
0
↓
↓
↓
↓
0
0
0
0
0
0
0
0
1
1
0
0
1
1
0
0
0
↓
↓
↓
↓
0
0
0
0
0
0
Blue Data
G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
↓
↓
1
1
1
0
1
1
SPEC TITLE
HX121WX1-100 Pre-Product Specification
1
0
1
1
1
1
1
1
1
1
1
1
PAGE
19 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
9.0 POWER SEQUENCE
To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall
be as shown in below
0.9VDD
Power Supply
0V
0.9VDD
0.1VDD
0.1VDD
T1
T5
T7
T2
T6
Interface Signal
Valid
0V
T3
Back- light
T4
0V
● T1 ≤ 10 ms
● 0 ≤ T2 ≤ 50 ms
● 200 ms ≤ T3
● 200 ms ≤ T4
● 0 ≤ T5 ≤ 50 ms
● 0 ≤ T6 ≤ 10ms
● 500ms ≤ T7
Notes : 1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep
high impedance.
2. Do not keep the interface signal high impedance when power is on.
3. Back Light must be turn on after power for logic and interface signal are valid.
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
20 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
10.0 MECHANICAL CHARACTERISTICS
10.1 Dimensional Requirements
Figure 6 & 7 (located in 11.0) shows mechanical outlines for the model
Parameter
Specification
Active Area
261.12(H) X 163.20(V)
Number of pixels
1280(H) X 800(V) (1 pixel = R + G + B dots)
Pixel pitch
0.204(H) X 0.204(V)
Pixel arrangement
RGB Vertical stripe
Display colors
262,144
Display mode
Normally Black
Outline dimension
276.8±0.3(H)×180.0(V)±0.3×6.8(D:Max.)
Weight
265(Typ.) / 275(Max.)
Back-light
SMD LED (48EA) Array
Unit
mm
mm
g
10.2 Mounting
See Figure 6 & 7 & 8. (shown in 11.0)
Parameter
Specification
Unit
Torque of side mounting screw
2.5(Max.)
kgf
Torque of ground plate screw
1.5(Max.)
kgf
Torque of top side screw
2.5(Max.)
kgf
10.3 Anti-Glare and Polarizer Hardness.
The surface of the LCD has an anti-glare coating to minimize reflection and a coating to
reduce scratching.
10.4 Light Leakage
There shall not be visible light from the back-lighting system around the edges of the
screen as seen from a distance 50cm from the screen with an overhead light level of
150lux. The manufacture shall furnish limit samples of the panel showing the light leakage
acceptable.
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
21 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
11.0 Mechanical Drawing
Figure 6. TFT-LCD Module Outline Dimension (Front View)
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
22 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
Figure 7. TFT-LCD Module Outline Dimensions (Rear view)
HX121WX1-100
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
23 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
Figure 8. TFT-LCD Module Section for Mounting
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
24 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
12.0 RELIABLITY TEST
The Reliability test items and its conditions are shown in below.
<Table 12. Reliability Test>
No
Test Item
Conditions
1
High temperature storage test
Ta = 60 °C, 240 hrs
2
Low temperature storage test
Ta = -20 °C, 240 hrs
3
High temperature & high humidity
operation test
Ta = 50 ℃, 80%RH, 240hrs
4
High temperature operation test
Ta = 50 °C, 240 hrs
5
Low temperature operation test
Ta = 0 °C, 240 hrs
6
Thermal shock
Ta = -20 °C ↔ 60 °C (30 min), 100 cycle
7
Vibration test
(non-operating)
Frequency : 10~500Hz
Gravity/AMP : 1.5G
Period : X,Y,Z 30min
8
Shock test
(non-operating)
Gravity : 220G
Pulse width : 2ms, half sine wave
±X, ±Y, ±Z Once for each direction
9
Electro-static discharge test
(non-operating)
Air : 150pF, 330ohm, 15KV
Contact : 150pF, 330ohm, 8KV
13.0 HANDLING & CAUTIONS
13.1 Cautions when taking out the module
y Pick the pouch only, when taking out module from a shipping package.
13.2 Cautions for handling the module
y As the electrostatic discharges may break the LCD module, handle the LCD module with
care. Peel a protection sheet off from the LCD panel surface as slowly as possible.
y As the LCD panel and back - light element are made from fragile glass (epoxy) material,
impulse and pressure to the LCD module should be avoided.
y As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth
without chemicals for cleaning.
y Do not pull the interface connector in or out while the LCD module is operating.
y Put the module display side down on a flat horizontal plane.
y Handle connectors and cables with care.
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
25 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
13.3 Cautions for the operation
y When the module is operating, do not lose MCLK, DE signals. If any one of these signals
were lost, the LCD panel would be damaged.
y Obey the supply voltage sequence. If wrong sequence is applied, the module would be
damaged.
13.4 Cautions for the atmosphere
y Dew drop atmosphere should be avoided.
y Do not store and/or operate the LCD module in a high temperature and/or humidity
atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively
low temperature atmosphere is recommended.
13.5 Cautions for the module characteristics
y Do not apply fixed pattern data signal to the LCD module at product aging.
y Applying fixed pattern for a long time may cause image sticking.
13.6 Cautions for the digitizer assembly
y When assembling FPC connector, do not flip connector past 90° due to possible damage
to connector.
y When positioning digitizer underneath driver IC, do not lift driver IC past 90° due to
possible damage to drive IC pattern.
y Please be warned that during assembly of digitizer, the opening or closing of FPC will
result in possible electrostatic discharge damage to the LED
13.7 Other cautions
y Do not re-adjust variable resistor or switch etc.
y When returning the module for repair or etc., Please pack the module not to be broken.
We recommend to use the original shipping packages.
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
26 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
14.0 LABELS
14.1 Product Label
HX121WX1-100
BOE HYDIS Barcode
1
2
3
4
5
X X
X
X
X X
X
6
7
X X X
X
X X X X X X
No 1. Control Number
No 5. Month (1, 2, 3,…, 9, X, Y, Z)
No 2. Rank / Grade
No 6. FG Code
No 3. Line Classification
(BOE HYDIS : H, LCM : L, BOE OT : A/B/C)
No 7. Serial Number
No 4. Year (5 : 2005, 6 : 2006, …)
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
27 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
14.2 Packing Label
Label Size: 108 mm (L) × 56 mm (W)
Contents
Model: HX121WX1-100
Q`ty: Module Q`ty in one box
Serial No.: Box Serial No. See next figure for detail
description.
Date: Packing Date
FG Code: FG Code of Product
10
HX121WX1-100
* 0000000000000 *
200X.X.XX
1
0
XXXX
00
0
00
0
0
000000
Type Grade Year Month ITEM-CODE Serial_no
SPEC. NUMBER
B2005-C001-A (3/3)
FG CODE
SPEC TITLE
HX121WX1-100 Pre-Product Specification
RoHS Mark
PAGE
28 OF 29
A4(210 X 297)
PRODUCT GROUP
REV
ISSUE DATE
TFT LCD PRODUCT
P2
2008. 01. 14
15.0 PACKING INFORMATION
15.1 Packing order
Put Pad into the box.
Put silica gels in the
box.
After sealing the
box, attach Packing
Label on the attach
position sign area of
the box.
Place a cover on
the top of the box.
As shown in the figure,
place the Modules
bundled by shielding
bag in the box.
15.2 Notes
z Box Dimension : 349.0mm(W) X 261.0mm(D) X 311.0mm(H)
z Package Quantity in one Box : 10pcs
SPEC. NUMBER
B2005-C001-A (3/3)
SPEC TITLE
HX121WX1-100 Pre-Product Specification
PAGE
29 OF 29
A4(210 X 297)