MLVS Series MLVS-0603 Series This specification is applicable to Chip Metal Oxide Varistor in multilayer technology. Specifications 1.Rating(25± 5 ℃) Features Working voltage Resistance Symbol 1. Keeping low and stable leakage current. 2. Excellent assembly solderability. Units 3. Low clamping Voltage. Test Condition 4. Quick response time (<1nSec.) MLVS0603M04 5. High transient current capability MLVS0603M06 6. Test Standard meets IEC 61000-4-2, 61000-4-4, MLVS0603M07 MLVS0603L08 and 61000-4-5. MLVS0603K11 MLVS0603K14 Part Number SeriesType Elements Size Tolerance Vrms MLV MLV MLV MLV MLV MLV S S S S S S 0603 0603 0603 0603 0603 0603 M M M L K K 04 06 07 08 11 14 VRMS VDC Ir imax Wmax Volts Volts (Max.) X106 ohm (Min.) Amps (Max.) < 10 µA 5 VDC 8/20µs Joules (Max.) 10/1000µ s 4 6 7 8 11 14 * 5.5 8 9 11 14 18 10 10* 10* 10 10 10 Dimensions L W 30 30 30 30 30 30 0.1 0.1 0.1 0.1 0.1 0.1 *Measured resistance at 3.3V DC VRMS – Maximum AC operating voltage the varistor can maintain and not exceed 10 µA leakage current VDC – Maximum DC operating voltage the varistor can maintain and not exceed 10 µA leakage current Ir – Resistance at 5 V DC imax – Maximum peak current which may be applied with 8/20us waveform without device failure Wmax – Maximum energy which may be dissipated with the 10/1000us waveform without device failure 2.Characteristics(25 ± 5℃) Varistor voltage Series Type / MLV — Multilayer Varistor Elements / S — Single Size /0603 —1.60x0.80x0.80mm3 Tolerance /M/L/K — ± 2 0%/ ± 15%/ ± 10% Vrms — Working Voltage Vrms Peak Transient current energy VV Symbol Clamping Voltage Capacitance Vc Cp ∆VV Volts % Volt (Max.) pF (typ.) Units 1mA DC 1KHz 1MHz Test Condition 1A 8/20µs MLVS0603M04 8 19 300 270 ±20 MLVS0603M06 11 27 250 230 ±20 MLVS0603M07 12.5 27 235 205 ±20 MLVS0603L08 15 33 220 190 ±15 MLVS0603K11 18 35 160 140 ±10 MLVS0603K14 22 40 140 120 ±10 VV – Voltage across the device measured at 1mA DC current Vc – Maximum peak current across the varistor with 8/20us waveform and 1A pulse current Cp – Device capacitance measured with zero volt bias 1Vrms Electrical Characteristics T 1.General technical Characteristics C C 0603 L 1.60 ± 0.20 W 0.80 ± 0.20 T 0.80 ± 0.20 C 0.30 ± 0.20 Unit : mm Operating temperature Storage temperature esponse time Solderability Solder leach resistance -55 … +125℃(85℃) -55 … +125℃(85℃) <1 ns 235℃, 2s 260℃, 10s 2. Environmental Characteristics Characteristics Specifications Bias humidity Thermal shock ∆VV /VV ≦±10% ∆VV /VV ≦±10% Vibration ∆VV /VV ≦±10% ∆VV /VV ≦±10% Full load voltage Solder leach resistance ∆VV /VV ≦±10% Test condition 90%RH, 40℃, Working voltage, 1000 hours -40℃ to 85℃, 30 min. cycle, 5 cycles 10 to 50 to 10 Hz, 1 min. cycle, 2 hours each in X-Y-Z Working voltage, 25℃, 1000 hours 260℃, 10s INPAQ TECHNOLOGY CO.,LTD