ALUMINUM ELECTROLYTIC CAPACITORS ZG 3.95mmL MAX. Chip Type, Wide Temperature Range series Chip type with 3.95mmLMAX height. Operating over wide temperature range of – 40 to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). ZT Smaller ZG Specifications Item Performance Characteristics Category Temperature Range –40 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 0.1 to 100µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater. 6.3 10 16 25 35 50 0.38 0.32 0.20 0.16 0.14 0.14 Rated voltage (V) 6.3 10 16 25 35 50 Impedance ratio Z–25°C / Z+20°C ZT / Z20 (MAX.) Z–40°C / Z+20°C 6 5 3 3 3 3 10 10 6 6 4 4 Rated voltage (V) Tangent of loss angle (tan δ) tan δ (MAX.) Stability at Low Temperature Capacitance change tan δ Leakage current 120Hz Within ±30% of the initial capacitance value 300% or less than the initial specified value Less than or equal to the initial specified value Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 105°C. Shelf Life After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Marking Black print on the case top. Chip Type V Capacitance 3.90 +0.05 –0.2 3.90 +0.05 –0.2 6.3 10 16 25 35 50 j A C E V H Code Within ±10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value 1 C±0.2 E E 0.5 to 0.8 Negative 0.5 to 0.8 Negative 2 3 4 5 6 7 8 9 10 11 12 13 14 U1 Z2 G3 14 C5 16 07 08 M9 C10 L11 112 G13 B14 U ZG 1 C 1 0 0 MC L 1 GB Positive A±0.3 A±0.3 A±0.3 A±0.3 Capacitance C±0.2 B±0.2 B±0.2 Series φD±0.5 φD±0.5 Series Lot No. X2 A2 10C 10C ZGZG Lot No.(C : 16V) Voltage Plastic platform 0.3 MAX. Plastic platform 0.3 MAX. 0.5 MAX. 0.5 MAX. Voltage (C : 16V) Voltage Capacitance change tan δ Leakage current Type numbering system (Example : 16V 10µF) Positive 120Hz 20°C φD A B C E 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 (mm) 6.3 2.4 6.6 6.6 2.2 Taping code Configuration Taping code Configuration Capacitance tolerance (±20%) Capacitance tolerance(10µF) (±20%) Rated capacitance Rated capacitance (10µF) Rated voltage (16V) RatedSeries voltage (16V) name SeriesType name Type Dimensions 6.3 0J V Cap. (µF) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 Code 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 4 5 5 6.3 10 1A 19 26 32 52 5 5 6.3 16 1C 24 30 40 4 5 6.3 6.3 25 1E 16 26 35 44 4 5 6.3 6.3 35 1V 11 20 33 42 4 5 6.3 13 22 36 4 4 4 4 4 4 4 5 6.3 50 1H Case size φ D (mm) 0.9 2.2 2.8 3.3 5.4 9.6 12. 16. 26. Rated ripple Rated ripple current (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size soldering by reflow are given in page 18,19. Please refer to page 3 for the minimum order quantity. CAT.8100D