EUA2005 1.5-W Mono Filterless Class-D Audio Power Amplifier DESCRIPTION FEATURES The EUA2005 is a high efficiency, 1.5W mono class-D audio power amplifier. A low noise, filterless PWM architecture eliminates the output filter, reducing external component count, system cost, and simplifying design. Operating in a single 5V supply, EUA2005 is capable of driving 8Ω speaker load at a continuous average output of 1.5W/10% THD+N or 1.3W/1% THD+N. The EUA2005 has high efficiency with speaker load compared to a typical class AB amplifier. With a 3.6V supply driving an 8Ω speaker , the efficiency for a 400mW power level is 84%. In cellular handsets, the earpiece, speaker phone, and melody ringer can each be driven by the EUA2005. The gain of EUA2005 is externally configurable which allows independent gain control from multiple sources by summing signals from seperate sources. The EUA2005 is available in DFN packages. z z z z z z z z z z z Efficiency at 3.6V With an 8-Ω Speaker: − 84% at 400 mW − 80% at 100 mW Low 2.8-mA Quiescent Current and 0.5-µA Shutdown Current 2.5V to 5.5V Wide Supply Voltage Optimized PWM Output Stage Eliminates LC Output Filter Improved PSRR (−72 dB) Eliminates Need for a Voltage Regulator Fully Differential Design Reduces RF Rectification and Eliminates Bypass Capacitor Improved CMRR Eliminates Two Input Coupling Capacitors Internally Generated 250-kHz Switching Frequency Integrated Pop and Click Suppression Circuitry 3mm × 3mm DFN-8 package RoHS compliant and 100% lead(Pb)-free APPLICATIONS z Typical Application Circuit Figure1. DS2005 Ver 1.1 Nov. 2006 1 Ideal for Wireless or Cellular Handsets and PDAs EUA2005 Pin Configurations Part Number Pin Configurations EUA2005 DFN-8 Pin Description PIN DFN-8 I/O SHUTDOWN 1 I NC 2 IN+ 3 I Positive differential input IN- 4 I Negative differential input VO+ 5 O Positive BTL output VDD 6 I Power supply GND 7 I High-current ground VO- 8 O Negative BTL output DS2005 Ver 1.1 Nov. 2006 DESCRIPTION Shutdown terminal (active low logic) No internal connection 2 EUA2005 Ordering Information Order Number Package Type Marking Operating Temperature range EUA2005JIR1 DFN-8 xxxx 2005A -40 °C to 85°C EUA2005 □ □ □ □ Lead Free Code 1: Lead Free 0: Lead Packing R: Tape & Reel Operating temperature range I: Industry Standard Package Type J: DFN DS2005 Ver 1.1 Nov. 2006 3 EUA2005 Absolute Maximum Ratings ▓ ▓ ▓ ▓ ▓ ▓ ▓ Supply Voltage, VDD ------------------------------------------------------------------------------------- -0.3 V to 6V Voltage at Any Input Pin ------------------------------------------------------------------------- -0.3 V to VDD +0.3V Junction Temperature, TJMAX --------------------------------------------------------------------------------------- 150°C Storage Temperature Rang, Tstg --------------------------------------------------------------------- -65°C to 150°C ESD Susceptibility -------------------------------------------------------------------------------------------- Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds ----------------------------------------- 2kV 260°C Thermal Resistance θJA (DFN) ---------------------------------------------------------------------------------------------------- 47°C/W Recommended Operating Conditions Supply voltage, VDD Min Max Unit 2.5 5.5 V High-level input voltage, VIH SHUTDOWN 1.6 VDD V Low-level input voltage, VIL SHUTDOWN 0 0.35 V Input resistor, RI Gain ≤ 20V/V (26dB) 15 Common mode input voltage range, VIC VDD=2.5V,5.5V,CMRR ≤ -49dB 0.5 VDD-0.8 V -40 85 °C Operating free-air temperature, TA kΩ Electrical Characteristics TA = 25°C (Unless otherwise noted) Symbol Parameter Conditions VOS Output offset voltage (measured differentially) VI= 0V,AV=2 V/V, VDD=2.5V to 5.5V PSRR Power supply rejection ratio CMRR Min EUA2005 Typ Max. Unit 1 25 mV VDD= 2.5V to 5.5V -72 -55 dB Common mode rejection ratio VDD= 2.5V to 5.5V, VIC= VDD/2 to 0.5V, VIC= VDD/2 to VDD -0.8 V -60 -48 dB I IH High-level input current VDD= 5.5V, VI= 5.8V 100 µA I IL Low-level input current VDD= 5.5V, VI= -0.3V 5 µA I(Q) I(SD) Quiescent current Shutdown current Static drain-source on-state rDS(on) resistance f(sw) Output impedance in SHUTDOWN Switching frequency VDD= 5.5V, no load 4.3 VDD= 3.6V, no load 2.8 VDD= 2.5V, no load 2 3.2 0.5 2 V (SHUTDOWN ) =0.35V, VDD= 2.5V to 5.5V VDD= 2.5V 700 VDD= 3.6V 500 VDD= 5.5V 400 V (SHUTDOWN ) =0.4V >1 VDD= 2.5V to 5.5V Resistance from shutdown toGND DS2005 Ver 1.1 Nov. 2006 200 250 300 4 4.9 mA µA mΩ kΩ 300 kHz kΩ EUA2005 Electrical Characteristics TA = 25°C ,Gain= 2V/V,RL=8Ω (Unless otherwise noted) EUA2005 Symbol Parameter Conditions Min Typ Max. VDD= 5V THD+N=10%, VDD= 3.6V f=1kHz, RL=8Ω PO Output power kSVR Supply ripple rejection ratio SNR Signal-to-noise ratio Vn VDD= 5V 1.30 CMRR ZI W 0.30 0.28 VDD= 3.6V,PO=0.5W, RL=8Ω, f=1kHz 0.30 VDD= 2.5V,PO=200mW, RL=8Ω, f=1kHz 0.28 VDD= 3.6V, Inputs f=217 Hz, ac-grounded with V(RIPPLE)=200mVpp CI= 2µF -60 dB 84 dB Common mode rejection ratio Start-up time from shutdown VDD= 3.6V DS2005 Ver 1.1 Nov. 2006 0.64 W VDD= 5V,PO=1W, RL=8Ω, f=1kHz VDD= 5V,PO=1W, RL=8Ω VDD= 3.6V, No weighting f=20Hz to 20kHz,Inputs ac-grounded with A weighting CI= 2µF VDD= 3.6V, f=217 Hz VIC=1 VPP Output voltage noise 0.79 0.39 VDD= 2.5V Total harmonic distortion THD+N plus noise 1.52 VDD= 2.5V THD+N=1%, VDD= 3.6V f=1kHz, RL=8Ω Unit 5 % 157 µVRMS 117 -55 dB 11.5 ms EUA2005 Typical Operating Characteristics EFFICIENCY vs OUTPUT POWER POWER DISSIPATION vs OUTPUT POWER 100 0.7 90 0.6 PD - Power Dissipation - W 80 Efficiency - % 70 VDD=5V, RL=8 ohm+33uH VDD=2.5V, RL= 8 ohm + 33uH 60 50 VDD=3.6V, RL=8 ohm + 33uH 40 30 20 0.5 0.4 0.3 0.2 VDD=3.6V, RL=8 ohm VDD=5V, RL=8 ohm 0.1 10 0 0.0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0.0 0.2 0.4 0.6 0.8 1.0 PO - Output Power - W PO - Output Power - W Figure2. Figure3. SUPPLY CURRENT vs OUTPUT POWER 1.2 1.4 SUPPLY CURRENT vs SUPPLY VOLTAGE 5.0 250 RL= 8 ohm, 33uH VDD=5V 4.5 VDD=3.6V 150 IDD - Supply Current -mA IDD - Supply Current - mA 200 VDD=2.5V 100 50 RL=8 ohm,(resistive) 4.0 3.5 3.0 2.5 RL=8 ohm, 33uH 2.0 NO Load 0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.5 1.4 2.5 3.0 3.5 PO - Output Power - W Figure4. 4.5 5.0 5.5 Figure5. SHUTDOWN CURRENT vs SHUTDOWN VOLTAGE OUTPUT POWER vs LOAD RESISTANCE 2.0 3.0 PO at 10% THD Gain=2 V/V F=1KHz VDD=5V 2.5 1.5 PO - Output Power - W I(SD) -Shutdown Current - uA 4.0 VDD - Supply Voltage -V 1.0 VDD=5V VDD=3.6V VDD=2.5V 0.5 2.0 VDD=3.6V 1.5 VDD=2.5V 1.0 0.5 0.0 0.0 0.0 0.1 0.2 0.3 0.4 0.5 8 Shutdown Voltage -V 16 20 24 RL - Load Resistance - ohm Figure7. Figure6. DS2005 Ver 1.1 Nov. 2006 12 6 28 32 EUA2005 OUTPUT POWER vs LOAD RESISTANCE 2.5 2.0 GAIN=2V/V F=1KHz 2.5 VDD=5V PO - Output Power -W PO - Output Power - W OUTPUT POWER vs SUPPLY VOLTAGE 3.0 PO at 1% THD Gain=2 V/V F=1KHz 1.5 VDD=3.6V 1.0 VDD=2.5V 0.5 2.0 1.5 1.0 RL = 8 ohm, 10% THD 0.5 RL= 8 ohm, 1% THD 0.0 8 12 16 20 24 28 0.0 32 2.5 RL - Load Resistance - ohm DS2005 Ver 1.1 Nov. 2006 3.0 3.5 4.0 VCC - Supply Voltage -V Figure8. Figure9. Figure10. Figure11. Figure12. Figure13. 7 4.5 5.0 EUA2005 THD+N - Total Harmonic Distortion + Noise -% TOTAL HARMONIC DISTORTION+NOISE vs COMMON MODE INPUT VOLTAGE 10 f= 1KHz Po=200mW 1 VDD=3.6V VDD=2.5V VDD=5V 0.1 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 VIC - Common Mode Input Voltage - V Figure14. Figure15. Figure16. Figure17. Figure19. Figure18. DS2005 Ver 1.1 Nov. 2006 8 EUA2005 SUPPLY RIPPLE REJECTION RATIO vs DC COMMON MODE VOLTAGE Supply Ripple Rejection Ratio - dB 0 -10 -20 -30 -40 VDD=2.5V VDD=3.6V -50 VDD=5V -60 -70 -80 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 DC Common Mode Voltage - V Figure21. Figure20. COMMON-MODE REJECTION RATIO vs COMMON-MODE INPUT VOLTAGE CMRR - Common Mode Rejection Ratio - dB 0 -10 -20 -30 -40 VDD=2.5V VDD=3.6V -50 -60 VDD=5V, Gain=2V/V -70 -80 -90 -100 0 1 2 3 4 5 VIC - Common Mode Input Voltage - V Figure22. DS2005 Ver 1.1 Nov. 2006 9 EUA2005 Application Information Table 1. Typical Component Values Fully Differential Amplifier The EUA2005 is a fully differential amplifier with differential inputs and outputs. The fully differential amplifier consists of a differential amplifier and a common-mode amplifier. The differential amplifier ensures that the amplifier outputs a differential voltage on the output that is equal to the differential input times the gain. The common-mode feedback ensures that the common-mode voltage at the output is biased around VDD/2 regardless of the common-mode voltage at the input. The fully differential EUA2005 can still be used with a single-ended input; however, the EUA2005 should be used with differential inputs when in a noisy environment, like a wireless handset, to ensure maximum noise rejection. Advantages of Fully Differential Amplifiers z REF DES VALUE RI 150kΩ ( ± 0.5%) CS 1µF (+22%,-80%) CI (1) 3.3nF ( ± 10%) (1) CI is only needed for single-ended input or if VICM is not between 0.5 V and VDD – 0.8 V. CI = 3.3 nF (with RI = 150 kΩ) gives a high-pass corner frequency of 321 Hz. Input-coupling capacitors not required: - The fully differential amplifier allows the inputs to be biased at voltage other than mid-supply. For example, if a codec has a midsupply lower than the midsupply of the EUA2005, the common-mode feedback circuit will adjust, and the EUA2005 outputs will still be biased at midsupply of the EUA2005. The inputs of the EUA2005 can be biased from 0.5V to VDD – 0.8 V. If the inputs are biased outside of that range, input-coupling capacitors are required. z Midsupply bypass capacitor, C(BYPASS), not required: - The fully differential amplifier does not require a bypass capacitor. This is because any shift in the midsupply affects both positive and negative channels equally and cancels at the differential output. z Better RF−immunity: -GSM handsets save power by turning on and shutting off the RF transmitter at a rate of 217 Hz. The transmitted signal is picked-up on input and output traces. The fully differential amplifier cancels the signal much better than the typical audio amplifier. Figure 23. Typical Application Schematic With Differential Input for a Wireless Phone Figure 24. Typical Application Schematic With Differential Input and Input Capacitors Component Selection Figure 23 shows the EUA2005 typical schematic with differential inputs and Figure 24 shows the EUA2005 with differential inputs and input capacitors, and Figure 25 shows the EUA2005 with single-ended inputs. Differential inputs should be used whenever possible because the single-ended inputs are much more susceptible to noise. Figure 25. Typical Application Schematic With Single-Ended Input DS2005 Ver 1.1 Nov. 2006 10 EUA2005 Input Resistors (RI) The input resistors (RI) set the gain of the amplifier according to equation (1). Gain = 2 × 150k Ω RI V ---------------------------------(1) V Resistor matching is very important in fully differential amplifiers. The balance of the output on the reference voltage depends on matched ratios of the resistors. CMRR, PSRR, and cancellation of the second harmonic distortion diminish if resistor mismatch occurs. Therefore, it is recommended to use 1% tolerance resistors or better to keep the performance optimized. Matching is more important than overall tolerance. Resistor arrays with 1% matching can be used with a tolerance greater than 1%. Place the input resistors very close to the EUA2005 to limit noise injection on the high-impedance nodes. For optimal performance the gain should be set to 2 V/V or lower. Lower gain allows the EUA2005 to operate at its best, and keeps a high voltage at the input making the inputs less susceptible to noise. Input Capacitors (CI) The EUA2005 does not require input coupling capacitors if the design uses a differential source that is biased from 0.5 V to VDD – 0.8 V (shown in Figure 23). If the input signal is not biased within the recommended common −mode input range, if needing to use the input as a high pass filter (shown in Figure 24), or if using a single-ended source (shown in Figure 25), input coupling capacitors are required. The input capacitors and input resistors form a high-pass filter with the corner frequency, fC, determined in equation (2). fc = 1 (2πR I C I ) --------------------------------------------(2) The value of the input capacitor is important to consider as it directly affects the bass (low frequency) performance of the circuit. Speakers in wireless phones cannot usually respond well to low frequencies, so the corner frequency can be set to block low frequencies in this application. Equation (3) is reconfigured to solve for the input coupling capacitance. 1 --------------------------------------------(3) Decoupling Capacitor (CS) CI = The EUA2005 is a high-performance class-D audio amplifier that requires adequate power supply decoupling to ensure the efficiency is high and total harmonic distortion (THD) is low. For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor, typically1 µF, placed as close as possible to the device VDD lead works best. Placing this decoupling capacitor close to the EUA2005 is very important for the efficiency of the class-D amplifier, because any resistance or inductance in the trace between the device and the capacitor can cause a loss in efficiency. For filtering lower-frequency noise signals, a 10µF or greater capacitor placed near the audio power amplifier would also help, but it is not required in most applications because of the high PSRR of this device. If the corner frequency is within the audio band, the capacitors should have a tolerance of ± 10% or better, because any mismatch in capacitance causes an impedance mismatch at the corner frequency and below. For a flat low-frequency response, use large input coupling capacitors (1 µF). However, in a GSM phone the ground signal is fluctuating at 217 Hz, but the signal from the codec does not have the same 217 Hz fluctuation. The difference between the two signals is amplified, sent to the speaker, and heard as a 217 Hz hum. DS2005 Ver 1.1 Nov. 2006 (2πR I f c ) Summing Input Signals Most wireless phones or PDAs need to sum signals at the audio power amplifier or just have two signal sources that need separate gain. The EUA2005 makes it easy to sum signals or use separate signal sources with different gains. Many phones now use the same speaker for the earpiece and ringer, where the wireless phone would require a much lower gain for the phone earpiece than for the ringer. PDAs and phones that have stereo headphones require summing of the right and left channels to output the stereo signal to the mono speaker. 11 EUA2005 Summing Two Differential Input Signals Two extra resistors are needed for summing differential signals (a total of 5 components). The gain for each input source can be set independently (see equations (4) and (5), and Figure 26). Gain1 = VO 2 × 150 kΩ V -----------------------(4) = V R I1 VI1 Gain 2 = VO 2 × 150 kΩ V -----------------------(5) = V R I2 VI 2 If summing left and right inputs with a gain of 1 V/V, use RI1 = RI2 = 300 kΩ. If summing a ring tone and a phone signal, set the ring-tone gain to Gain 2 = 2 V/V, and the phone gain to Gain 1 = 0.1 V/V. The resistor values would be. . . RI1=3MΩ, and=RI2=150kΩ Summing a Differential Input Signal and a Single-Ended Input Signal Figure 27 shows how to sum a differential input signal and a single-ended input signal. Ground noise can couple in through IN+ with this method. It is better to use differential inputs. The corner frequency of the single-ended input is set by CI2, shown in equation (8). To assure that each input is balanced, the single-ended input must be driven by a low-impedance source even if the input is not in use V 2 × 150 kΩ V ------------------------ (6) Gain1 = O = V R I1 VI1 Gain 2 = C I2 = VO 2 × 150 kΩ V -----------------------(7) = R I2 V VI 2 1 (2πR I2 f c 2 ) -----------------------------------------(8) If summing a ring tone and a phone signal, the phone signal should use a differential input signal while the ring tone might be limited to a single-ended signal. Phone gain is set at gain 1 = 0.1 V/V, and the ring-tone gain is set to gain 2 = 2 V/V, the resistor values would be… RI1=3MΩ, and=RI2=150kΩ The high pass corner frequency of the single-ended input is set by CI2. If the desired corner frequency is less than 20 Hz... C I2 > Figure 26. Application Schematic With EUA2005 Summing Two Differential Inputs 1 (2π150 kΩ 20 Hz ) --------------------------------(9) C I 2 > 53 P F -----------------------------------------------(10) Figure 27. Application Schematic With EUA2005 Summing Input and Single-Ended Input Signals DS2005 Ver 1.1 Nov. 2006 12 EUA2005 Summing Two Single-Ended Input Signals Four resistors and three capacitors are needed for summing single-ended input signals. The gain and corner frequencies (fc1 and fc2) for each input source can be set independently (see equations (11) through (14), and Figure 28). Resistor, RP, and capacitor, CP, are needed on the IN+ terminal to match the impedance on the IN− terminal. The single-ended inputs must be driven by low impedance sources even if one of the inputs is not outputting an ac signal. Gain1 = VO 2 × 150 kΩ V = V ---------------------(11) R I1 VI1 Gain 2 = VO 2 × 150 kΩ V ---------------------(12) = V R I2 VI 2 C I1 = C I2 = 1 (2πR I1f c1 ) -----------------------------------------(13) 1 (2πR I2 f c 2 ) -----------------------------------------(14) CP = C I1 + C I 2 -------------------------------------------(15) RP = R I1 × R I 2 (R I1 + R I2 ) ------------------------------------- (16) Figure 28. Application Schematic With EUA2005 Summing Two Single-Ended Input DS2005 Ver 1.1 Nov. 2006 13 EUA2005 Packaging Information DFN-8 NOTE 1. All dimensions are in millimeters, θ is in degrees 2. M: The maximum allowable corner on the molded plastic body corner 3. Dimension D does not include mold protrusions or gate burrs. Mold protrusions and gate burrs shall not exceed 0.15mm per side 4. Dimension E does not include interterminal mold protrusions or terminal protrusions. Interminal mold protrusions and/or terminal protrusions shall not exceed 0.20mm per side 5. Dimension b applies to plated terminals. Dimension A1 is primarily Y terminal plating, but may or may not include a small protrusion of terminal below the bottom surface of the package 6. Burr shall not exceed 0.060mm 7. JEDEC MO-229 SYMBOLS A A1 A3 b D D1 E E1 e L aaa bbb ccc M θ DS2005 Ver 1.1 Nov. 2006 MIN. 0.70 0 -----0.20 2.85 -----2.85 ----------0.25 ---------------------12 DIMENSIONS IN MILLIMETERS NOM. MAX. 0.80 0.90 0.015 0.03 0.20 REF -----0.30 0.40 3.00 3.15 2.30 BSC -----3.00 3.15 1.50 BSC -----0.65 BSC ----0.35 0.45 0.25 -----0.10 -----0.10 ----------0.05 -----0 14