ISSI IS31AP2006

IS31AP2006
3W MONO FILTER-LESS CLASS-D AUDIO POWER AMPLIFIER
April 2012
GENERAL DESCRIPTION
FEATURES
The IS31AP2006 is a high efficiency, 3W mono
Class-D audio power amplifier. A low noise, filter-less
PWM architecture eliminates the output filter, reducing
external component count, system cost, and
simplifying design.

Operating in a single 5V supply, IS31AP2006 is
capable of driving 4Ω speaker load at a continuous
average output of 3W with 10% THD+N. The
IS31AP2006 has high efficiency with speaker load
compared to a typical class-AB amplifier.
In cellular handsets, the earpiece, speaker phone, and
melody ringer can each be driven by the IS31AP2006.
The gain of IS31AP2006 is externally configurable
which allows independent gain control from multiple
sources by summing signals from each function.
The IS31AP2006 is available in DFN-8 (3mm×3mm)
packages.





5V supply at THD = 10%
-3W into 4Ω (Typ.)
-1.70W into 8Ω (Typ.)
Efficiency at 5V:
-83% at 400mW with a 4Ω speaker
-89% at 400mW with an 8Ω speaker
Optimized PWM output stage eliminates LC
output filter
Fully differential design reduces RF rectification
and eliminates bypass capacitor
Integrated pop-and-click suppression circuitry
DFN-8 (3mm×3mm) packages
APPLICATIONS







Wireless or cellular handsets and PDAs
Portable DVD player
Notebook PC
Portable radio
Educational toys
USB speakers
Portable gaming
TYPICAL APPLICATION CIRCUIT
Figure 1
Typical Application Circuit (Differential Input)
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 03/27/2012
1
IS31AP2006
Figure 2
Typical Application Schematic (Single-ended Input)
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 03/27/2012
2
IS31AP2006
PIN CONFIGURATION
Package
Pin Configuration (Top view)
DFN-8
PIN DESCRIPTION
No.
Pin
Description
1
OUT+
Positive audio output.
2, 3
VCC
Power supply.
4
IN-
Negative audio input.
5
IN+
Positive audio input.
6
SDB
Shutdown control, active low logic.
7
GND
Ground.
8
OUT-
Negative audio output.
Thermal Pad
Connect to GND.
Copyright © 2011 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that: a.) the risk of injury or damage has been minimized; b.) the user assume all such risks; and c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 03/27/2012
3
IS31AP2006
ORDERING INFORMATION
Industrial Range: -40°C to +85°C
Order Part No.
Package
QTY/Reel
IS31AP2006-DLS2-TR
DFN-8, Lead-free
2500
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 03/27/2012
4
IS31AP2006
ABSOLUTE MAXIMUM RATINGS
Supply voltage, VCC
Voltage at any input pin
Maximum junction temperature, TJMAX
Storage temperature range, TSTG
Operating temperature range, TA
ESD HBM
-0.3V ~ +6.0V
-0.3V ~ VCC+0.3V
150°C
-65°C ~ +150°C
−40°C ~ +85°C
7kV
Note:
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and
functional operation of the device at these or any other condition beyond those indicated in the operational sections of the specifications is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
VCC = 2.7V ~ 5.5V, TA = 25°C, unless otherwise noted.
Symbol
Parameter
Condition
VCC
Supply voltage
VOS
Output offset voltage
(measured differentially)
ICC
Quiescent current
ISD
Shutdown current
fsw
Switching frequency
RIN
Input resistor
Gain  20V/V
Input gain
RIN = 150kΩ
Gain
VIH
High-level input voltage
VIL
Low-level input voltage
Min.
Typ.
2.7
VSDB = 0V, AV = 2V/V
10
VCC = 5.5V, no load
2.6
VCC = 2.7V, no load
1.2
VSDB = 0.4V
Max.
Unit
5.5
V
mV
mA
1
250
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 03/27/2012
μA
kHz
15
kΩ
2
V/V
1.4
V
0.4
V
5
IS31AP2006
ELECTRICAL CHARACTERISTICS (NOTE 1)
TA = 25°C, Gain= 2V/V.
Symbol
Parameter
Condition
THD+N = 10%
f = 1kHz, RL = 8Ω
THD+N = 10%
f = 1kHz, RL = 4Ω
PO
Output power
THD+N = 1%
f = 1kHz, RL = 8Ω
THD+N=1%
f = 1kHz, RL = 4Ω
THD+N
Output voltage noise
tWU
SNR
PSRR
Typ.
VCC = 5.0V
1.70
VCC = 4.2V
1.20
VCC = 3.6V
0.83
VCC = 5.0V
3
VCC = 4.2V
2.05
VCC = 3.6V
1.55
VCC = 5.0V
1.45
VCC = 4.2V
0.95
VCC = 3.6V
0.66
VCC = 5.0V
2.50
VCC = 4.2V
1.70
VCC = 3.6V
1.25
Total
harmonic VCC = 5.0V, PO =1.0W, RL = 8Ω, f = 1kHz
distortion plus noise VCC = 5.0V, PO =1.2W, RL = 4Ω, f = 1kHz
VN
Min.
VCC = 3.6V~5V, f =20Hz to 20kHz, inputs
ac-grounded with CI = 1μF A-Weighting
0.28
0.31
Max.
Unit
W
W
W
W
%
68
μVrms
Wake-up time from
VCC = 3.6V
shutdown
36
ms
Signal-to-noise ratio
PO =1.0W, RL = 8Ω, VCC = 5.0V
92
dB
Power supply
rejection ratio
VCC = 2.5V ~ 5.5V
-55
dB
Note 1: Guaranteed by design.
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 03/27/2012
6
IS31AP2006
TYPICAL PERFORMANCE CHARACTERISTICS
20
20
RL = 8Ω+33µH
f = 1kHz
10
VCC = 3.6V
VCC = 3.6V
5
THD+N(%)
5
THD+N(%)
RL = 4Ω+33µH
f = 1kHz
10
2
VCC = 4.2V
1
2
VCC = 4.2V
1
0.5
0.5
0.2
0.2
VCC = 5.0V
VCC = 5.0V
0.1
10m
20m
50m
100m
200m
500m
1
2
0.1
10m
3
20m
50m
Output Power(W)
Figure 4
20
RL = 8Ω+33µH
10
2
VCC = 5.0V
PO = 1W
1
0.2
0.1
VCC = 3.6V
PO = 500mW
3 4
2
THD+N vs. Output Power
RL = 4Ω+33µH
VCC = 5.0V
PO = 1.2W
2
1
0.2
VCC = 3.6V
PO = 650mW
0.05
0.02
0.02
20
50
100
200
500
1k
2k
5k
0.01
10k 20k
20
50
100
200
Frequency(Hz)
Figure 5
Figure 6
1k
2k
5k
10k 20k
THD+N vs. Frequency
0
RL = 8Ω+33μH
Input Grounded
VCC = 3.6V~5.0V
RL = 8Ω+33µH
-20
100
PSRR(dB)
70
50
30
-40
VCC = 3.6V
-60
VCC = 4.2V
20
10
20
500
Frequency(Hz)
THD+N vs. Frequency
200
Output Voltage(uV)
1
0.1
0.05
0.01
500m
20
THD+N(%)
THD+N(%)
10
200m
Output Power(W)
THD+N vs. Output Power
Figure 3
100m
VCC = 5.0V
-80
50
100
200
1k
2k
5k
10k
20k
-100
20
50
100
Noise
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 03/27/2012
500
1k
2k
5k
20k
Frequency(Hz)
Frequency(Hz)
Figure 7
200
Figure 8
PSRR vs. Frequency
7
IS31AP2006
1.8
RL = 4Ω+33μH
f = 1kHz
THD+N = 10%
1.4
Output Power(W)
3
THD+N = 10%
Output Power(W)
1.6
3.5
RL = 8Ω+33μH
f = 1kHz
1.2
1
0.8
THD+N = 1%
0.6
2.5
2
1.5
1
0.4
THD+N = 1%
0.5
0.2
0
2.5
3
3.5
4
4.5
5
0
2.5
3
4
4.5
5
Power Supply(V)
Power Supply(V)
Figure 9
3.5
Output Power vs. Supply Voltage
Figure 10
Output Power vs. Supply Voltage
RL=8Ohm
Efficiency(%)
RL=4Ohm
Vcc=5V
Gain=2V/V
0
Figure 11
Efficiency vs. Output Power
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 03/27/2012
8
IS31AP2006
FUNCTIONAL BLOCK DIAGRAM
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 03/27/2012
9
IS31AP2006
APPLICATION INFORMATION
FULLY DIFFERENTIAL AMPLIFIER
VBattery
2,3
VCC
The IS31AP2006 is a fully differential amplifier with
differential inputs and outputs. The fully differential
amplifier consists of a differential amplifier and a
common-mode amplifier. The differential amplifier
ensures that the amplifier outputs a differential voltage
on the output that is equal to the differential input times
the gain. The common-mode feedback ensures that
the common-mode voltage at the output is biased
around VCC/2 regardless of the common-mode voltage
at the input. The fully differential IS31AP2006 can still
be used with a single-ended input; however, the
IS31AP2006 should be used with differential inputs
when in a noisy environment, like a wireless handset,
to ensure maximum noise rejection.
INPUT RESISTORS (RIN)
ADVANTAGES OF FULLY DIFFERENTIAL
AMPLIFIERS
The input resistors (RIN) set the gain of the amplifier
according to equation (1).
The fully differential amplifier does not require a
bypass capacitor. This is because any shift in the
midsupply affects both positive and negative channels
equally and cancels at the differential output.
GSM handsets save power by turning on and shutting
off the RF transmitter at a rate of 217Hz. The
transmitted signal is picked-up on input and output
traces. The fully differential amplifier cancels the signal
much better than the typical audio amplifier.
COMPONENT SELECTION
Figure 12 shows the IS31AP2006 with differential
inputs and optional input capacitors. Input capacitors
are used when the common mode input voltage range
specs can not be guaranteed or high pass filter is
considered.
Figure 13 shows the IS31AP2006 with single-ended
inputs. The input capacitors have to be used in the
single ended case because it is much more
susceptible to noise in this case.
VBattery
CS
1 F
CIN0.1 F
2, 3
RIN150k
Differential
Input
4
5
CIN+
0.1 F
VCC
0.1 F
ININ+
OUT+
IS31AP2006
OUT-
1
8
RIN+
150k
6
Shutdown
Control
SDB
GND
7
100k
Figure 12
Typical Application Circuit with Differential Input
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 03/27/2012
CS
1 F
0.1 F
RIN150k
CIN0.1 F
Single-ended
Input
4
5
CIN+
0.1 F
OUT+
IN-
IS31AP2006
IN+
OUT-
1
8
RIN+
150k
6
Shutdown
Control
SDB
GND
7
100k
Figure 13
Typical Application Circuit with Single-Ended Input
Gain 
2  150k   V 
RIN
 
V 
(1)
Resistor matching is very important in fully differential
amplifiers. The balance of the output on the reference
voltage depends on matched ratios of the resistors.
CMRR, PSRR, and cancellation of the second
harmonic distortion diminish if resistor mismatch
occurs. Therefore, it is recommended to use 1%
accuracy resistors or better to keep the performance
optimized. Matching is more important than overall
accuracy.
Place the input resistors close to the IS31AP2006 to
reduce noise injection on the high-impedance nodes.
For optimal performance the gain should be set to
2V/V or lower. Lower gain allows the IS31AP2006 to
operate at its best, and keeps a high voltage at the
input making the inputs less susceptible to noise.
DECOUPLING CAPACITOR (CS)
The IS31AP2006 is a high-performance Class-D audio
amplifier that requires adequate power supply
decoupling to ensure high efficiency and low total
harmonic distortion (THD). For higher frequency
transients, spikes, or digital noises on the line, a good
low equivalent-series-resistance (ESR) ceramic
capacitor, typically 1μF, placed as close as possible to
the device VCC pin works best. Placing this decoupling
capacitor close to the IS31AP2006 is also important for
the efficiency of the Class-D amplifier, because any
resistance or inductance in the trace between the
device and the capacitor can cause a loss in efficiency.
For filtering lower-frequency noise signals, a 10μF or
greater capacitor placed near the audio power
amplifier would also be helpful, but it is not required in
most applications because of better PSRR of this
device.
10
IS31AP2006
INPUT CAPACITORS (CIN)
The input capacitors and input resistors form a
high-pass filter with the corner frequency, fC,
determined in equation (2).
1
f 
c 2R C 
IN IN
(2)
The value of the input capacitor is important to
consider as it directly affects the bass (low frequency)
performance of the circuit. Speakers in wireless
phones cannot usually respond well to low frequencies,
so the corner frequency can be set to block low
frequencies in this application.
Equation (3) is reconfigured to solve for the input
coupling capacitance.
C
IN

1
2RIN f c 
(3)
Figure 14
Application Circuit with Summing Two Differential Inputs
If summing left and right inputs with a gain of 1V/V, use
RIN1 = RIN2 = 300kΩ.
If summing a ring tone and a phone signal, set the
ring-tone gain to Gain2 = 2V/V, and the phone gain to
Gain1 = 0.1V/V. The resistor values would be.
RIN1 = 3MΩ, and RIN2 = 150kΩ.
If the corner frequency is within the audio band, the
capacitors should have a tolerance of  10% or better,
because any mismatch in capacitance causes an
impedance mismatch at the corner frequency and
below.
For a flat low-frequency response, use large input
coupling capacitors (1μF). However, in a GSM phone
the ground signal is fluctuating at 217Hz, but the signal
from the codec does not have the same 217Hz
fluctuation. The difference between the two signals is
amplified, sent to the speaker, and heard as a 217Hz
hum.
SUMMING A DIFFERENTIAL INPUT SIGNAL AND A
SINGLE-ENDED INPUT SIGNAL
Figure 15 shows how to sum a differential input signal
and a single-ended input signal. Ground noise may
couple in through IN- with this method. It is better to
use differential inputs. The corner frequency of the
single-ended input is set by CIN2, shown in equation (8).
To assure that each input is balanced, the
single-ended input must be driven by a low-impedance
source even if the input is not in use.
Gain1 
2  150 k  V 
 
R IN 1
V 
(6)
Gain 2 
2  150 k  V 
 
R IN 2
V 
(7)
SUMMING INPUT SIGNALS
Most wireless phones or PDAs need to sum signals at
the audio power amplifier or just have two signal
sources that need separate gain. The IS31AP2006
makes it easy to sum signals or use separate signal
sources with different gains. Many phones now use the
same speaker for the earpiece and ringer, where the
wireless phone would require a much lower gain for
the phone earpiece than for the ringer. PDAs and
phones that have stereo headphones require summing
of the right and left channels to output the stereo signal
to the mono speaker.
If summing a ring tone and phone signals, the phone
signals should use the differential inputs while the ring
tone should use the single-ended input. The phone
gain is set at Gain2 = 0.1V/V, and the ring-tone gain is
set to Gain2 = 0.1V/V, the resistor values would be
SUMMING TWO DIFFERENTIAL INPUT SIGNALS
RIN1 = 150kΩ, and RIN2 = 3MΩ
Two extra resistors are needed for summing
differential signals. The gain for each input source can
be set independently (see equations (4) and (5), and
Figure 14).
The high pass corner frequency of the single-ended
input is set by CIN2. If the desired corner frequency is
less than 20Hz.
2  150 k  V 
Gain1 
 
R IN 1
V 
(4)
2  150 k  V 
Gain 2 
 
R IN 2
V 
(5)
C IN 2 
C IN 1 
1
1
(9)
2RIN 1 f C 1
C IN 2  53 pF
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 03/27/2012
(8)
2RIN 2 f c 2 
(10)
11
IS31AP2006
C IN 1 
1
(13)
2RIN 1 f C 1
1
2RIN 2 f C 2
(14)
C p  C IN 1  C IN 2
(15)
C IN 2 
RP 
R IN 1  R IN 2
R IN 1  R IN 2 
(16)
Figure 15 Application Circuit with Summing Differential Input and
Single-Ended Input Signals
SUMMING TWO SINGLE-ENDED INPUT SIGNALS
The gain and corner frequencies (fC1 and fC2) for each
input source can be set independently (see equations
(11) through (14), and Figure 16). Resistor, RP, and
capacitor, CP, are needed on the IN+ terminal to match
the impedance on the IN- terminal.
The single-ended inputs must be driven by low
impedance sources.
Gain1 
2  150 k  V 
 
R IN 1
V 
(11)
Gain 2 
2  150 k  V 
 
R IN 2
V 
(12)
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 03/27/2012
CIN2-
RIN2-
CIN1-
RIN1-
Single-ended
Input 2
4
Single-ended
Input 1
5
CP
Figure 16
Inputs
ININ+
RP
Application Circuit with Summing Two Single-Ended
12
IS31AP2006
CLASSIFICATION REFLOW PROFILES
Profile Feature
Pb-Free Assembly
Preheat & Soak
Temperature min (Tsmin)
Temperature max (Tsmax)
Time (Tsmin to Tsmax) (ts)
150°C
200°C
60-120 seconds
Average ramp-up rate (Tsmax to Tp)
3°C/second max.
Liquidous temperature (TL)
Time at liquidous (tL)
217°C
60-150 seconds
Peak package body temperature (Tp)*
Max 260°C
Time (tp)** within 5°C of the specified
classification temperature (Tc)
Max 30 seconds
Average ramp-down rate (Tp to Tsmax)
6°C/second max.
Time 25°C to peak temperature
Figure 17
8 minutes max.
Classification Profile
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 03/27/2012
13
IS31AP2006
PACKAGING INFORMATION
DFN-8
Note: All dimensions in millimeters unless otherwise stated.
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 03/27/2012
14