MK2304-2 ZERO DELAY, LOW SKEW BUFFER Description Features The MK2304-2 is a low jitter, low skew, high performance Phase Lock Loop (PLL) based zero delay buffer for high speed applications. Based on ICS’ proprietary low jitter PLL techniques, the device provides four low skew outputs at speeds up to 133 MHz at 3.3 V. The MK2304-2 includes a bank of two outputs running at 1/2X. In the zero delay mode, the rising edge of the input clock is aligned with the rising edges of all 4 outputs. Compared to competitive CMOS devices, the MK2304-2 has the lowest jitter. • • • • • • • Packaged in 8 pin SOIC Zero input-output delay Two 1X outputs plus two 1/2X outputs Output to output skew is less than 200 ps Output clocks up from 10 MHz to 133 MHz at 3.3 V Ability to generate 2X the input Full CMOS outputs with 18 mA output drive capability at TTL levels at 3.3 V • Spread SmartTM technology works with spread The MK2304-2 PLL enters a power-down state when there are no rising edges on the REF input. In this mode, all outputs are tri-stated and the PLL is turned off, resulting in leass than 25 µA of current draw. spectrum clock generators • • • • • ICS manufactures the largest variety of clock generators and buffers and is the largest clock supplier in the world. Advanced, low power, sub micron CMOS process Operating voltage of 3.3 V Available in industial temperature operation Available in Pb (lead) free package Low Standby Current Block Diagram VDD 1 FBIN CLKIN CLKA1 PLL CLKA2 BANK A CLKB1 /2 CLKB2 BANK B 1 GND 1 MDS 2304-2 C I n t e gra te d C i r c u i t S y s t e m s ● 525 Race Stre et, San Jo se, CA 9 5126 Revision 050306 ● te l (40 8) 2 97-12 01 ● w w w. i c st . c o m MK2304-2 ZERO DELAY, LOW SKEW BUFFER Pin Assignment Feedback Configuration Table REF 1 8 FBK CLKA1 2 7 VDD CLKA2 3 6 CLKB2 GND 4 5 CLKB1 Feedback From Bank A Bank B CLKA1:A2 CLKIN 2XCLKIN CLKB1:B2 CLKIN/2 CLKIN 8 Pi n ( 150 mi l ) SOI C Pin Descriptions Pin Number Pin Name Pin Type Pin Description 1 REF Input 2 CLKA1 Output Clock A1 output. 3 CLKA2 Output Clock A2 output. 4 GND Power Connect to ground. 5 CLKB1 Output Clock B1 output. 6 CLKB1 Output Clock B2 output. 7 VDD Power 3.3V Power Supply. 8 FBK Input PLL feedback input Clock input. Connect to input clock source, 5 V tolerant input. External Components The Mk2304-2 requires a minimum number of external components for proper operation. Decoupling capacitors of 0.1µF should be connected between VDD and GND, as close to the part as possible. A 33Ω series terminating resistor should be used on each clock output to reduce reflections. 2 MDS 2304-2 C In te grated Circuit Systems ● 525 Ra ce Street, San Jose, CA 9512 6 Revision 050306 ● tel (4 08) 297-1 201 ● w w w. i c s t . c o m MK2304-2 ZERO DELAY, LOW SKEW BUFFER Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the MK2304-2. These ratings, which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature (commercial) 0 to +70 °C Ambient Operating Temperature (industrial) -40 to +85 °C Storage Temperature -65 to +150 °C Junction Temperature 125 °C Soldering Temperature 260 °C Recommended Operation Conditions Parameter Min. Max. Units 0 +70 °C Ambient Operating Temperature (industrial) -40 +85 °C Power Supply Voltage (measured in respect to GND) +3.0 +3.6 V Ambient Operating Temperature (commercial) Typ. DC Electrical Characteristics VDD=3.3 V ±10%, Amb temp -40° C to 85° C Parameter Symbol Conditions Min. Typ. Operating Voltage VDD 3.0 Input High Voltage VIH 2 Input Low Voltage VIL Output High Voltage VOH IOH = -8 mA Output Low Voltage VOL IOL = 8 mA Operating Supply Current 100 MHz, CLKIN IDD No Load 45 Stand by Supply Current 0 MHz, CLKIN IDD No Load 12 Short Circuit Current IOS Each output Input Capacitance CIN FBIN Units 3.6 V V 0.8 2.4 0.4 25 525 Ra ce Street, San Jose, CA 9512 6 uA TBD mA 7 pF 3 ● V mA 50 MDS 2304-2 C V V Power-up Time In te grated Circuit Systems Max. ms Revision 050306 ● tel (4 08) 297-1 201 ● w w w. i c s t . c o m MK2304-2 ZERO DELAY, LOW SKEW BUFFER AC Electrical Characteristics VDD = 3.3V ±10%, Ambient Temperature -40° C to 85° C Parameter Symbol Conditions Min. Typ. Max. Units Output Frequency FBIN to CLKA1, 30 pF Load 10 100 MHz Output Frequency FBIN to CLKA1, 15 pf Load 10 133 MHz Output Rise Time tOR 0.8 to 2.0 V, CL=30 pF 2.2 ns Output Rise Time tOR 0.8 to 2.0 V, CL=15 pF 1.5 ns Output Fall Time tOF 0.8 to 2.0 V, CL=30 pF 2.2 ns Output Fall Time tOF 0.8 to 2.0 V, CL=15 pF 1.5 ns Output Clock Duty Cycle At 1.4 V, CL=30 pf 40 50 60 % Output Clock Duty Cycle At 1.4 V, CL=15 pf 45 50 65 % Device-to-Device skew, equally loaded Rising edges at VDD/2 500 ps Output-to-Output skew, equally loaded, On same bank Rising edges at VDD/2 200 ps Skew from Output Bank A to Output Bank B All outputs equally loaded 400 ps Delay CLKIN Rising Edge to FBIN Rising Edge Measured at VDD/2 ±250 ps Cycle-to-Cycle Jitter 30 pF loads 66.67 MHz outputs 400 ps 15 pF loads 66.67 MHz outputs 375 ps 1 ms PLL Lock Time Stable power supply, valid clocks on CLKIN, FBIN tLOCK Thermal Characteristics Parameter Thermal Resistance Junction to Ambient Thermal Resistance Junction to Case Conditions Min. Typ. Max. Units θJA Still air 120 °C/W θJA 1 m/s air flow 115 °C/W θJA 3 m/s air flow 105 °C/W 58 °C/W θJC 4 MDS 2304-2 C In te grated Circuit Systems Symbol ● 525 Ra ce Street, San Jose, CA 9512 6 Revision 050306 ● tel (4 08) 297-1 201 ● w w w. i c s t . c o m MK2304-2 ZERO DELAY, LOW SKEW BUFFER Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Narrow Body) Package dimensions are kept current with JEDEC Publication No. 95 Millimeters 8 Symbol E A A1 B C D E e H h L α H INDEX AREA 1 2 D Min Max 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BASIC 5.80 6.20 0.25 0.50 0.40 1.27 0° 8° Inches* Min Max .0532 .0688 .0040 .0098 .013 .020 .0075 .0098 .1890 .1968 .1497 .1574 0.050 BASIC .2284 .2440 .010 .020 .016 .050 0° 8° *For reference only. Controlling dimensions are in mm. A h x 45 A1 C -Ce SEATING PLANE B L .10 (.004) C Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature MK2304S-2 2304S-02 Tubes 8-pin SOIC 0 to 70° C MK2304S-2T 2304S-02 Tape and Reel 8-pin SOIC 0 to 70° C MK2304S-2I 2304S02I Tubes 8-pin SOIC -40° C to 85° C MK2304S-2IT 2304S02I Tape and Reel 8-pin SOIC -40° C to 85° C MK2304S-2LF 2304S02L Tubes 8-pin SOIC 0 to 70° C MK2304S-2LFT 2304S02L Tape and Reel 8-pin SOIC 0 to 70° C MK2304S-2ILF 2304S2IL Tubes 8-pin SOIC -40° C to 85° C MK2304S-2ILFT 2304S2IL Tape and Reel 8-pin SOIC -40° C to 85° C Parts that are ordered with a "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. 5 MDS 2304-2 C In te grated Circuit Systems ● 525 Ra ce Street, San Jose, CA 9512 6 Revision 050306 ● tel (4 08) 297-1 201 ● w w w. i c s t . c o m