5.0X6.0mm SURFACE MOUNT LED LAMP AA5060SEC/E HYPER ORANGE Description Features The Hyper Orange source color devices are made with SINGLE COLOR. SUITABLE FOR ALL SMT ASSEMBLY AND SOLDER DH InGaAlP on GaAs substrate Light Emitting Diode. PROCESS. AVAILABLE ON TAPE AND REEL. IDEAL FOR BACKLIGHTING. PACKAGE : 500PCS / REEL. RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. SPEC NO: DSAD0899 REV NO: V.6 DATE: MAR/14/2005 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI PAGE: 1 OF 4 ERP: 1201000530 Selection Guide Part No. Dice AA5060SEC/E Iv (mcd) @ 50mA Lens Type HYPER ORANGE(InGaAIP) Viewing Angle Min. Typ. 2θ θ1/2 650 1000 100° WATER CLEAR Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Hyper Orange λD Dominant Wavelength ∆λ1/2 Max. Units Test Conditions 630 nm IF=20mA Hyper Orange 621 nm IF=20mA Spectral Line Half-width Hyper Orange 20 nm IF=20mA C Capacitance Hyper Orange 25 pF VF=0V;f=1MHz VF Forward Voltage Hyper Orange 2.0 2.5 V IF=20mA IR Reverse Current Hyper Orange 10 uA VR = 5V Absolute Maximum Ratings at TA=25°C Parameter Hyper Orange Units Power dissipation 125 mW DC Forward Current 50 mA Peak Forward Current [1] 195 mA 5 V Reverse Voltage Operating/Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD0899 REV NO: V.6 DATE: MAR/14/2005 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI PAGE: 2 OF 4 ERP: 1201000530 Hyper Orange AA5060SEC/E SPEC NO: DSAD0899 REV NO: V.6 DATE: MAR/14/2005 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI PAGE: 3 OF 4 ERP: 1201000530 AA5060SEC/E Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. D i g i t a l l y s i g n e d b y N I N G T I N G c n = N I N G T I N G , o = N I N G T I N G , c = C N D a t e : 2 0 0 5 . 0 3 . 1 4 1 4 : 2 8 : 1 6 + 0 8 '0 0 'R e a s o n : < n o n e > SPEC NO: DSAD0899 REV NO: V.6 DATE: MAR/14/2005 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: B.H.LI PAGE: 4 OF 4 ERP: 1201000530