SUBMINIATURE SOLID STATE LAMP AM27SURC03 HYPER RED Description Features The Hyper Red source color devices are SUBMINIATURE PACKAGE. made with DH InGaAlP on GaAs substrate GULL WING. LONG LIFE - SOLID STATE RELIABILITY. Light Emitting Diode. LOW PACKAGE PROFILE. PACKAGE :1000PCS / REEL. RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. Specifications are subject to change without notice. SPEC NO: DSAD1296 REV NO: V.3 DATE: APR/07/2005 PAGE: 1 OF 4 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1202000388 Selection Guide Part No. Dice AM27SURC03 Iv (mcd) @ 20mA Lens Type HYPER RED (InGaAlP) Viewing Angle Min. Typ. 2 θ 1/2 280 1000 20° WATER CLEAR Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device λpeak Peak Wavelength Hyper Red λD Dominant Wavelength ∆λ1/2 Typ. Max. Units Test Conditions 640 nm IF=20mA Hyper Red 628 nm IF=20mA Spectral Line Half-width Hyper Red 27 nm IF=20mA C Capacitance Hyper Red 45 pF VF=0V;f=1MHz VF Forward Voltage Hyper Red 1.9 2.5 V IF=20mA IR Reverse Current Hyper Red 10 uA VR = 5V Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Units Power dissipation 170 mW DC Forward Current 30 mA Peak Forward Current [1] 185 mA 5 V Reverse Voltage Operating / Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD1296 REV NO: V.3 DATE: APR/07/2005 PAGE: 2 OF 4 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1202000388 Hyper Red AM27SURC03 SPEC NO: DSAD1296 REV NO: V.3 DATE: APR/07/2005 PAGE: 3 OF 4 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1202000388 AM27SURC03 Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) Remarks: If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. SPEC NO: DSAD1296 REV NO: V.3 APPROVED: J. Lu CHECKED: Allen Liu DATE: APR/07/2005 PAGE: 4 OF 4 DRAWN: H.Q.YUAN ERP:1202000388 D i g i t a l l y s i g n e d b y N I N G T I N G c n = N I N G T I N G , o = N I N G T I N G , c = C N D a t e : 2 0 0 5 . 0 4 . 0 7 1 5 : 3 4 : 4 5 + 0 8 '0 0 'R e a s o n : < n o n e >