KINGBRIGHT AM27SYCK08

SUBMINIATURE SOLID STATE LAMP
AM27SYCK08
SUPER BRIGHT YELLOW
Features
Description
OWIDE VIEWING ANGLE.
The Super Bright Yellow source color devices are made
OSUBMINIATURE PACKAGE.
with DH InGaAlP on GaAs substrate Light Emitting Diode.
OYOKE LEAD.
OLONG LIFE-SOLID STATE RELIABILITY.
OLOW PACKAGE PROFILE.
OPACKAGE : 1000PCS / REEL.
ORoHS COMPLIANT.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the lead emerge from the package.
4. Specifications are subject to change without notice.
SPEC NO: DSAD1319
REV NO: V.2
DATE: MAR/10/2005
PAGE: 1 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: S.H.CHEN
ERP:1202000415
Selection Guide
Part No.
Dice
AM27SYCK08
Iv (mcd)
@ 20mA
Lens Type
SUPER BRIGHT YELLOW (InGaAIP)
WATER CLEAR
Viewing
Angle
Min.
Typ.
2θ1/2
70
300
20°
Note:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
Super Bright Yellow
λD
Dominant Wavelength
∆λ1/2
Max.
Units
Test Conditions
590
nm
IF=20mA
Super Bright Yellow
590
nm
IF=20mA
Spectral Line Half-width
Super Bright Yellow
20
nm
IF=20mA
C
Capacitance
Super Bright Yellow
20
pF
VF=0V;f=1MHz
VF
Forward Voltage
Super Bright Yellow
2.0
2.5
V
IF=20mA
IR
Reverse Current
Super Bright Yellow
10
uA
VR = 5V
Absolute Maximum Ratings at TA=25°C
Parameter
Super Bright Yellow
Units
Power dissipation
125
mW
DC Forward Current
30
mA
Peak Forward Current [1]
175
mA
5
V
Reverse Voltage
-40°C To +85°C
Operating/Storage Temperature
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAD1319
REV NO: V.2
DATE: MAR/10/2005
PAGE: 2 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: S.H.CHEN
ERP:1202000415
Super Bright Yellow
AM27SYCK08
SPEC NO: DSAD1319
REV NO: V.2
DATE: MAR/10/2005
PAGE: 3 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: S.H.CHEN
ERP:1202000415
AM27SYCK08
Recommended Soldering Pattern
(Units : mm)
Tape Specifications
(Units : mm)
Remarks:
If there is sorting requirement (eg. forward voltage, luminous intensity or wavelength), the condition as follows:
1.Wavelength: +/-1nm (Test condition is based on the sorting standard).
2.Luminous intensity: +/-15% (Test condition is based on the sorting standard).
3.Forward voltage: +/-0.1V (Test condition is based on the sorting standard).
SPEC NO: DSAD1319
REV NO: V.2
DATE: MAR/10/2005
PAGE: 4 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: S.H.CHEN
ERP:1202000415