KINGBRIGHT WP1034HDT

2mm FLAT TOP LED LAM P
WP1034HDT
Features
BRIGHT RED
Description
MOUNTS FLUSH WITH PANEL.
The Bright Red source color devices are made with Gallium
LOW POWER CONSUMPTION.
Phosphide Red Light Emitting Diode.
LONG LIFE - SOLID STATE RELIABILITY.
RoHS COMPLIANT.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. Specifications are subject to change without notice.
SPEC NO: DSAF2525
REV NO: V.1
DATE: APR/18/2005
PAGE: 1 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1101000333
Selection Guide
Part No.
Dice
WP1034HDT
Iv (mcd)
@ 10mA
Lens Type
BRIGHT RED (GaP)
RED DIFFUSED
Viewing
Angle
Min.
Typ.
2θ
θ1/2
0.4
1
70°
Note:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
λpeak
Peak Wavelength
Bright Red
λD
Dominant Wavelength
∆λ1/2
Typ.
Max.
Units
Test Conditions
700
nm
IF=20mA
Bright Red
660
nm
IF=20mA
Spectral Line Half-width
Bright Red
45
nm
IF=20mA
C
Capacitance
Bright Red
40
pF
VF=0V;f=1MHz
VF
Forward Voltage
Bright Red
2.25
2.5
V
IF=20mA
IR
Reverse Current
Bright Red
10
uA
VR = 5V
Absolute Maximum Ratings at TA=25°C
Parameter
Bright Red
Units
Power dissipation
120
mW
DC Forward Current
25
mA
Peak Forward Current [1]
130
mA
5
V
Reverse Voltage
Operating/Storage Temperature
-40°C To +85°C
Lead Solder Temperature [2]
260°C For 3 Seconds
Lead Solder Temperature [3]
260°C For 5 Seconds
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. 2mm below package base.
3. 5mm below package base.
SPEC NO: DSAF2525
REV NO: V.1
DATE: APR/18/2005
PAGE: 2 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1101000333
Bright Red
WP1034HDT
SPEC NO: DSAF2525
REV NO: V.1
DATE: APR/18/2005
PAGE: 3 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1101000333
PACKING & LABEL SPECIFICATIONS
WP1034HDT
Remarks:
If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength),
the typical accuracy of the sorting process is as follows:
1. Wavelength: +/-1nm
2. Luminous Intensity: +/-15%
3. Forward Voltage: +/-0.1V
Note: Accuracy may depend on the sorting parameters.
SPEC NO: DSAF2525
REV NO: V.1
DATE: APR/18/2005
PAGE: 4 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: W.J.ZHU
ERP:1101000333