T-1 (3mm) RIGHT ANGLE LED INDICATOR Part Number: WP130WDT/EGW High Efficiency Red Green Features Description z PRE-TRIMMED LEADS FOR PC BOARD MOUNTING. The High Efficiency Red source color devices are made with z 3 LEADS WITH COMMON CATHODE. Gallium Arsenide Phosphide on Gallium Phosphide Orange z I.C. COMPATIBLE. Light Emitting Diode. z BLACK CASE ENHANCES CONTRAST RATIO. The Green source color devices are made with Gallium z UL RATING : 94V-0. Phosphide Green Light Emitting Diode. z HOUSING MATERIAL: TYPE 66 NYLON. z RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. Specifications are subject to change without notice. SPEC NO: DSAF1530 REV NO: V.3 DATE: MAY/19/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 1 OF 5 ERP: 1102000189 Selection Guide Part No. Dice Lens Type High Efficiency Red (GaAsP/GaP) WP130WDT/EGW Iv (mcd) [2] @ 20mA Min. Typ. 7 30 7 25 WHITE DIFFUSED Green (GaP) Viewing Angle [1] 2θ1/2 60° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2. Luminous intensity/ luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength High Efficiency Red Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 627 565 nm IF=20mA High Efficiency Red Green 625 568 nm IF=20mA Spectral Line Half-width High Efficiency Red Green 45 30 nm IF=20mA C Capacitance High Efficiency Red Green 15 15 pF VF=0V;f=1MHz VF [2] Forward Voltage High Efficiency Red Green 2 2.2 2.5 2.5 V IF=20mA IR Reverse Current High Efficiency Red Green 10 10 uA VR = 5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter High Efficiency Red Green Units Power dissipation 75 62.5 mW DC Forward Current 30 25 mA Peak Forward Current [1] 160 140 mA Reverse Voltage 5 Operating / Storage Temperature V -40°C To +85°C Lead Solder Temperature [2] 260°C For 3 Seconds Lead Solder Temperature [3] 260°C For 5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. SPEC NO: DSAF1530 REV NO: V.3 DATE: MAY/19/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 2 OF 5 ERP: 1102000189 WP130WDT/EGW High Efficiency Red SPEC NO: DSAF1530 REV NO: V.3 DATE: MAY/19/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 3 OF 5 ERP: 1102000189 Green SPEC NO: DSAF1530 REV NO: V.3 DATE: MAY/19/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 4 OF 5 ERP: 1102000189 PACKING & LABEL SPECIFICATIONS WP130WDT/EGW SPEC NO: DSAF1530 REV NO: V.3 DATE: MAY/19/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 5 OF 5 ERP: 1102000189